Characterization of parasitics in TO-packaged high-speed laser modules

An elaborate analysis of the parasitic network of high-speed through-hole packaging (TO)-type laser modules is presented using a small-signal equivalent circuit model. The intrinsic laser diode is obtained using the optical modulation technique, and is embedded into the model as a separate component. Three step-by-step measurements are made for determining the packaging parasitic network, including the test fixture, TO header, submount, bonding wire, and parasitics of the laser chip. A good agreement between simulated and measured results confirms the validation and accuracy of the characterization procedures. Furthermore, several key parasitic elements are found based on the simulation of the high-frequency responses of the packaged devices. It is expected that the 3-dB bandwidth of 12 GHz or more of the low-cost TO packaged laser module may be achieved using the proposed optimization method.

Fabrication and characterization of TO packaged high-speed laser modules - art. no. 682407

Various high-speed laser modules are fabricated by TO-Packaged processes, such as FP laser modules, DFB laser modules, and VCSEL modules. Furthermore,, the resonance among the circuit elements provides an approach to compensating the TO packaging parasitics, and improving the frequency response of the devices. The detailed equivalent circuit model is established to investigate both the laser diode and packaging comprehensively. The small-signal modulation bandwidths of the TO packaged FP laser, DFB laser and the VCSEL modules are more than 10, 9.7 and 8 GHz, respectively.

High Speed VCSEL-Based Parallel Optical Transmission Modules

Design and fabrication of a parallel optical transmitter are reported. The optimized 12 channel parallel optical transmitter,with each channel＇s data rate up to 3Gbit/s,is designed, assembled, and measured. A top-emitting 850nm vertical cavity surface emitting laser（VCSEL） array is adopted as the light source,and the VCSEL chip is directly wire bonded to a 12 channel driver IC. The outputs of the VCSEL array are directly butt coupled into a 12 channel fiber array. Small form factor pluggable （SFP） packaging technology is used in the module to support hot pluggable in application. The performance results of the module are demonstrated. At an operating current of 8mA, an eye diagram at 3Gbit/s is achieved with an optical output of more than 1mW.

Comparison between weight loss of bends in a pneumatic conveyor and erosion rate obtained in a centrifugal erosion tester for the same materials

In order to find a link between results obtained from a laboratory erosion tester and tests carried out on a pneumatic conveyor, a comparison has been made between weight loss from bends on an industrial-scale pneumatic conveyor and erosion rates obtained in a small centrifugal erosion tester, for the same materials. Identical test conditions have been applied to both experiments so that comparable test results have been obtained. The erosion rate of mild steel commonly used as the wall material of conveyor pipes and pipe bends was determined individually on both test rigs. A relationship between weight loss from the bends and erosion rate determined from the tester has been developed. A discussion based on the results and their applicability to the prediction of wear in pneumatic conveyors concludes the paper.

AND Logic Gates Based on Small Molecules with Chemical Inputs and Luminescence Output

AND logic gate behaviour can be recognized in chemical-responsive luminescence phenomena concerning small molecules. Though initial developments concerned separate and distinguishable chemical species as inputs, consideration of other types of input sets allows substantial expansion of the sub-field. Dissection of these molecular devices into modules, where possible, enables analysis of their logic behaviour according to supramolecular photochemical mechanisms.

Dynamic Approach and Testbed for Small and Medium Players Simulation in Smart Grid Environments

The Smart Grid environment allows the integration of resources of small and medium players through the use of Demand Response programs. Despite the clear advantages for the grid, the integration of consumers must be carefully done. This paper proposes a system which simulates small and medium players. The system is essential to produce tests and studies about the active participation of small and medium players in the Smart Grid environment. When comparing to similar systems, the advantages comprise the capability to deal with three types of loads – virtual, contextual and real. It can have several loads optimization modules and it can run in real time. The use of modules and the dynamic configuration of the player results in a system which can represent different players in an easy and independent way. This paper describes the system and all its capabilities.

The World Health Organization Multi-Professional Patient Safety Curriculum : implementation of key modules and its impact on patient safety knowledge, skills, and attitudes of medical students at the University of Algarve

ABSTRACT - Objectives: We attempted to show how the implementation of the key elements of the World Health Organization Patient Safety Curriculum Guide Multi-professional Edition in an undergraduate curriculum affected the knowledge, skills, and attitudes towards patient safety in a graduate entry Portuguese Medical School. Methods: After receiving formal recognition by the WHO as a Complementary Test Site and approval of the organizational ethics committee , the validated pre-course questionnaires measuring the knowledge, skills, and attitudes to patient safety were administered to the 2nd and3rd year students pursuing a four-year course (N = 46). The key modules of the curriculum were implemented over the academic year by employing a variety of learning strategies including expert lecturers, small group problem-based teaching sessions, and Simulation Laboratory sessions. The identical questionnaires were then administered and the impact was measured. The Curriculum Guide was evaluated as a health education tool in this context. Results: A significant number of the respondents, 47 % (n = 22), reported having received some form of prior patient safety training. The effect on Patient Safety Knowledge was assessed by using the percentage of correct pre- and post-course answers to construct 2 × 2 contingency tables and by applying Fishers’ test (two-tailed). No significant differences were detected (p < 0.05). To assess the effect of the intervention on Patient Safety skills and attitudes, the mean and standard deviation were calculated for the pre and post-course responses, and independent samples were subjected to Mann-Whitney’s test. The attitudinal survey indicated a very high baseline incidence of desirable attitudes and skills toward patient safety. Significant changes were detected (p < 0.05) regarding what should happen if an error is made (p = 0.016), the role of healthcare organizations in error reporting (p = 0.006), and the extent of medical error (p = 0.005). Conclusions: The implementation of selected modules of the WHO Patient Safety Curriculum was associated with a number of positive changes regarding patient safety skills and attitudes, with a baseline incidence of highly desirable patient safety attitudes, but no measureable change on the patient safety knowledge, at the University of Algarve Medical School. The significance of these results is discussed along with implications and suggestions for future research.

Large is fast, small is tight: determinants of speed and affinity in subunit capture by a periplasmic chaperone

The chaperone/usher pathway assembles surface virulence organelles of Gram-negative bacteria, consisting of fibers of linearly polymerized protein subunits. Fiber subunits are connected through 'donor strand complementation': each subunit completes the immunoglobulin (Ig)-like fold of the neighboring subunit by donating the seventh β-strand in trans. Whereas the folding of Ig domains is a fast first-order process, folding of Ig modules into the fiber conformation is a slow second-order process. Periplasmic chaperones separate this process in two parts by forming transient complexes with subunits. Interactions between chaperones and subunits are also based on the principle of donor strand complementation. In this study, we have performed mutagenesis of the binding motifs of the Caf1M chaperone and Caf1 capsular subunit from Yersinia pestis and analyzed the effect of the mutations on the structure, stability, and kinetics of Caf1M-Caf1 and Caf1-Caf1 interactions. The results suggest that a large hydrophobic effect combined with extensive main-chain hydrogen bonding enables Caf1M to rapidly bind an early folding intermediate of Caf1 and direct its partial folding. The switch from the Caf1M-Caf1 contact to the less hydrophobic, but considerably tighter and less dynamic Caf1-Caf1 contact occurs via the zip-out-zip-in donor strand exchange pathway with pocket 5 acting as the initiation site. Based on these findings, Caf1M was engineered to bind Caf1 faster, tighter, or both faster and tighter. To our knowledge, this is the first successful attempt to rationally design an assembly chaperone with improved chaperone function.

Conceptual Product Development in Small Corporations

The main objective of the thesis “Conceptual Product Development in Small Corporations” is by the use of a case study test the MFD™-method (Erixon G. , 1998) combined with PMM in a product development project. (Henceforth called MFD™/PMM-method). The MFD™/PMM-method used for documenting and controlling a product development project has since it was introduced been used in several industries and projects. The method has been proved to be a good way of working with the early stages of product development, however, there are almost only projects carried out on large industries which means that there are very few references to how the MFD™/PMM-method works in a small corporation. Therefore, was the case study in the thesis “Conceptual Product Development in Small Corporations” carried out in a small corporation to find out whether the MFD™/PMM-method also can be applied and used in such a corporation.The PMM was proposed in a paper presented at Delft University of Technology in Holland 1998 by the author and Gunnar Erixon. (See appended paper C: The chart of modular function deployment.) The title “The chart of modular function deployment” was later renamed as PMM, Product Management Map. (Sweden PreCAD AB, 2000). The PMM consists of a QFD-matrix linked to MIM (Module Indication Matrix) via a coupling matrix which makes it possible to make an unbroken chain from the customer domain to the designed product/modules. The PMM makes it easy to correct omissions made in creating new products and modules.In the thesis “Conceptual Product Development in Small Corporations” the universal MFD™/PMM-method has been adapted by the author to three models of product development; original-, evolutionary- and incremental development.The evolutionary adapted MFD™/PMM-method was tested as a case study at Atlings AB in the community Ockelbo. Atlings AB is a small corporation with a total number of 50 employees and an annual turnover of 9 million €. The product studied at the corporation was a steady rest for supporting long shafts in turning. The project team consisted of management director, a sales promoter, a production engineer, a design engineer and a workshop technician, the author as team leader and a colleague from Dalarna University as discussion partner. The project team has had six meetings.The project team managed to use MFD™ and to make a complete PMM of the studied product. There were no real problems occurring in the project work, on the contrary the team members worked very well in the group, having ideas how to improve the product. Instead, the challenge for a small company is how to work with the MFD™/PMM-method in the long run! If the MFD™/PMM-method is to be a useful tool for the company it needs to be used continuously and that requires financial and personnel resources. One way for the company to overcome the probable lack of recourses regarding capital and personnel is to establish a good cooperation with a regional university or a development centre.

Concept design of a novel tactile probe tip for down scaled 3D CMMs

Although coordinate metrology has reached a very high state of development concerning versatility and accuracy for common engineering parts, a high precision capability with nano scale resolution and accuracy is often hard to achieve when it is required to measure very small parts and features. The limiting component is the bulky probing system of traditional CMMs (coordinate measuring machines). In order to satisfy increasing demand for highly accurate geometrical measurements on small parts and small structures, a new measuring probe of high sensitivity and small geometrical dimension with low contact forces needs to be developed. In this paper, a novel probing system, which combines a FBG (Fibre Bragg Grating) embedded optical fibre tactile probe with an optical sensing technique, has been proposed. With the sensor elements integrated into the probe tip directly, the system sensitivity can be increased significantly. A preliminary theoretical analysis of the sensitivity of the FBG fibre sensor under axial and lateral end point loading has been presented and the results show that this micro scale probe has great potential to realize a resolution of 1nanometer on geometrical measurement of small parts.

Temperature Dynamics Investigation At Small And Shallow Lakes Using Hydrodynamic Model

A three-dimensional time-dependent hydrodynamic and heat transport model of Lake Binaba, a shallow and small dam reservoir in Ghana, emphasizing the simulation of dynamics and thermal structure has been developed. Most numerical studies of temperature dynamics in reservoirs are based on one- or two-dimensional models. These models are not applicable for reservoirs characterized with complex flow pattern and unsteady heat exchange between the atmosphere and water surface. Continuity, momentum and temperature transport equations have been solved. Proper assignment of boundary conditions, especially surface heat fluxes, has been found crucial in simulating the lake’s hydrothermal dynamics. This model is based on the Reynolds Average Navier-Stokes equations, using a Boussinesq approach, with a standard k − ε turbulence closure to solve the flow field. The thermal model includes a heat source term, which takes into account the short wave radiation and also heat convection at the free surface, which is function of air temperatures, wind velocity and stability conditions of atmospheric boundary layer over the water surface. The governing equations of the model have been solved by OpenFOAM; an open source, freely available CFD toolbox. As its core, OpenFOAM has a set of efficient C++ modules that are used to build solvers. It uses collocated, polyhedral numerics that can be applied on unstructured meshes and can be easily extended to run in parallel. A new solver has been developed to solve the hydrothermal model of lake. The simulated temperature was compared against a 15 days field data set. Simulated and measured temperature profiles in the probe locations show reasonable agreement. The model might be able to compute total heat storage of water bodies to estimate evaporation from water surface.

Report on the retrieval of data for small areas of microcomputers ( REDATAM) National Training Workshop

Through this workshop, database experts from the various ministries and the Central Statistical Office (CSO) were introduced to the CREATE and PROCESS modules of the REDATAM software, which could be used for database creation and analysis of data. This workshop was the second in a series of workshops aimed at promoting human-resource and capacity-building at the national and regional levels in the use of the REDATAM software. It also served as a qualifier for a follow-up workshop on the use of the web-publishing application of the software to be held in 2010.

Multiseries Lie groups and asymptotic modules for characterizing and solving integrable models

A multiseries integrable model (MSIM) is defined as a family of compatible flows on an infinite-dimensional Lie group of N-tuples of formal series around N given poles on the Riemann sphere. Broad classes of solutions to a MSIM are characterized through modules over rings of rational functions, called asymptotic modules. Possible ways for constructing asymptotic modules are Riemann-Hilbert and ∂̄ problems. When MSIM's are written in terms of the group coordinates, some of them can be contracted into standard integrable models involving a small number of scalar functions only. Simple contractible MSIM's corresponding to one pole, yield the Ablowitz-Kaup-Newell-Segur (AKNS) hierarchy. Two-pole contractible MSIM's are exhibited, which lead to a hierarchy of solvable systems of nonlinear differential equations consisting of (2 + 1) -dimensional evolution equations and of quite strong differential constraints. © 1989 American Institute of Physics.

The Role of Nanometer-Scaled Ligand Patterns in Polyvalent Binding by Large Mannan-Binding Lectin Oligomers

Mannan-binding lectin (MBL) is an important protein of the innate immune system and protects the body against infection through opsonization and activation of the complement system on surfaces with an appropriate presentation of carbohydrate ligands. The quaternary structure of human MBL is built from oligomerization of structural units into polydisperse complexes typically with three to eight structural units, each containing three lectin domains. Insight into the connection between the structure and ligand-binding properties of these oligomers has been lacking. In this article, we present an analysis of the binding to neoglycoprotein-coated surfaces by size-fractionated human MBL oligomers studied with small-angle x-ray scattering and surface plasmon resonance spectroscopy. The MBL oligomers bound to these surfaces mainly in two modes, with dissociation constants in the micro to nanomolar order. The binding kinetics were markedly influenced by both the density of ligands and the number of ligand-binding domains in the oligomers. These findings demonstrated that the MBL-binding kinetics are critically dependent on structural characteristics on the nanometer scale, both with regard to the dimensions of the oligomer, as well as the ligand presentation on surfaces. Therefore, our work suggested that the surface binding of MBL involves recognition of patterns with dimensions on the order of 10-20 nm. The recent understanding that the surfaces of many microbes are organized with structural features on the nanometer scale suggests that these properties of MBL ligand recognition potentially constitute an important part of the pattern-recognition ability of these polyvalent oligomers. The Journal of Immunology, 2012, 188: 1292-1306.

Benchmark Structures and Binding Energies of Small Water Clusters with Anharmonicity Corrections

For (H2O)n where n = 1–10, we used a scheme combining molecular dynamics sampling with high level ab initio calculations to locate the global and many low lying local minima for each cluster. For each isomer, we extrapolated the RI-MP2 energies to their complete basis set limit, included a CCSD(T) correction using a smaller basis set and added finite temperature corrections within the rigid-rotor-harmonic-oscillator (RRHO) model using scaled and unscaled harmonic vibrational frequencies. The vibrational scaling factors were determined specifically for water clusters by comparing harmonic frequencies with VPT2 fundamental frequencies. We find the CCSD(T) correction to the RI-MP2 binding energy to be small (<1%) but still important in determining accurate conformational energies. Anharmonic corrections are found to be non-negligble; they do not alter the energetic ordering of isomers, but they do lower the free energies of formation of the water clusters by as much as 4 kcal/mol at 298.15 K.