石油二次运移机理物理模拟研究

Oil and gas migration is very important for theoretical hydrocarbon geology study and exploration practice, but related research is weak. Physical simulation is a main method to study oil migration. Systematic experiments were done to quantitatively describe the migration patterns, path characters and oil saturation by adjusting the possible dynamic factors respectively. The following conclusions were drawn. 1. Darcy velocity and pore throat diameter were calculated according to seepage cross-sectional area and glass beads arrangement. With such normalized Darcy velocity and pore throat diameter, the date from one and two dimensional experiments can be reasonably drawn in two phase diagrams. It is found that the migration pattern can be identified using only one dimensionless number L which is defined as the ration of capillary number and Bond number. 2. Oil saturated in the pores between glass beads was used as calibration and oil saturation in the path was measured by magnetic resonance imaging. The results show that oil saturation in the center of migration path can reach 100%, is higher than oil saturation in the edge of migration path. 3. Percolation backbone during secondary oil migration was identified experimentally using Hele-Shaw cell. The backbone formed mainly because of the spatial variation of the cluster conductivity caused by oil saturation heterogeneity, main resistant force change, and path shrinkage and snap-off. Percolation backbone improves hydrocarbon migration efficiency and is a favorable factor for reservoir forming. 4. In the three dimensional filling models, the thickness of the secondary migration path is mall. It is only 2.5cm even for the piston pattern. Inclination of the model is the main influencing factor of the secondary path width.

中国大中型气田天然气成藏物理化学模拟研究

Natural gas pays more important role in the society as clean fuel. Natural gas exploration has been enhanced in recent years in many countries. It also has prospective future in our country through "85" and "95" national research. Many big size gas fields have been discovered in different formations in different basins such as lower and upper Paleozoic in Erdos basin, Tertiary system in Kuche depression in Tarim basin, Triassic system in east of Sichuan basin. Because gas bearing basins had been experienced multiple tectogenesis. The characteristics of natural gases usually in one gas field are that they have multiple source rocks and are multiple maturities and formed in different ages. There has most difficult to research on the gas-rock correlation and mechanism of gas formation. Develop advanced techniques and methods and apply them to solve above problems is necessary. The research is focused on the critical techniques of geochemistry and physical simulation of gas-rock correlation and gas formation. The lists in the following are conclusions through research and lots of experiments. I 8 advanced techniques have been developed or improved about gas-rock correlation and gas migration, accumulation and formation. A series of geochemistry techniques has been developed about analyzing inclusion enclave. They are analyzing gas and liquid composition and biomarker and on-line individual carbon isotope composition in inclusion enclave. These techniques combing the inclusion homogeneous temperature can be applied to study on gas-rock correlation directly and gas migration, filling and formation ages. Technique of on-line determination individual gas carbon isotope composition in kerogen and bitumen thermal pyrolysis is developed. It is applied to determine the source of natural is kerogen thermal degradation or oil pyrolysis. Method of on-line determination individual gas carbon isotope composition in rock thermal simulation has being improved. Based on the "95"former research, on-line determination individual gas carbon isotope composition in different type of maceral and rocks thermal pyrolys is has been determined. The conclusion is that carbon isotope composition of benzene and toluene in homogenous texture kerogen thermal degradation is almost same at different maturity. By comparison, that in mixture type kerogen thermal pyrolysis jumps from step to step with the changes of maturity. This conclusion is a good proof of gas-rock dynamic correlation. 3. Biomarker of rock can be determined directly through research. It solves the problems such as long period preparing sample, light composition losing and sample contamination etc. It can be applied to research the character of source rock and mechanism of source rock expulsion and the path of hydrocarbon migration etc. 4. The process of hydrocarbon dynamic generation in source rock can be seen at every stage applying locating observation and thermal simulation of ESEM. The mechanism of hydrocarbon generation and expulsion in source rock is discussed according to the experiments. This technique is advanced in the world. 5. A sample injection system whose character is higher vacuum, lower leaks and lower blank has been built up to analyze inert gas. He,Ar,Kr and Xe can be determined continuously on one instrument and one injection. This is advanced in domestic. 7. Quality and quantity analysis of benzene ring compounds and phenolic compounds and determination of organic acid and aqueous gas analysis are applied to research the relationship between compounds in formation water and gas formation. This is another new idea to study the gas-rock correlation and gas formation. 8. Inclusion analysis data can be used to calculate the Paleo-fluid density, Paleo-geothermal gradient and Paleo-geopressure gradient and then to calculate the Paleo-fluid potential. It's also a new method to research the direction of hydrocarbon migration and accumulation. 9. Equipment of natural gas formation simulation is produced during the research to probe how the physical properties of rock affect the gas migration and accumulation and what efficiency of gas migrate and factors of gas formation and the models of different type of migration are. II study is focused on that if the source rocks of lower Paleozoic generated hydrocarbon and what the source rocks of weathered formation gas pool and the mechanism of gas formation are though many advanced techniques application. There are four conclusions. 1.The maturity of Majiagou formation source rocks is higher in south than that in north. There also have parts of the higher maturity in middle and east. Anomalous thermal pays important role in big size field formation in middle of basin. 2. The amount of gas generation in high-over maturity source rocks in lower Paleozoic is lager than that of most absorption of source rocks. Lower Paleozoic source rocks are effective source rocks. Universal bitumen exists in Ordovician source rocks to prove that Ordovician source rocks had generated hydrocarbon. Bitumen has some attribution to the middle gas pool formation. 3. Comprehensive gas-rock correlation says that natural gases of north, west, south of middle gas field of basin mainly come from lower Paleozoic source rocks. The attribution ratio of lower Paleozoic source rocks is 60%-70%. Natural gases of other areas mainly come from upper Paleozoic. The attribution ratio of upper Paleozoic source rocks is 70%. 4. Paleozoic gases migration phase of Erdos basin are also interesting. The relative abundance of gasoline aromatic is quite low especially toluene that of which is divided by that of methyl-cyclohexane is less than 0.2 in upper Paleozoic gas pool. The migration phase of upper Paleozoic gas may be aqueous phase. By comparison, the relative abundance of gasoline aromatic is higher in lower Paleozoic gas. The distribution character of gasoline gas is similar with that in source rock thermal simulation. The migration phase of it may be free phase. IH Comprehensive gas-rock correlation is also processed in Kuche depression Tarim basin. The mechanism of gas formation is probed and the gas formation model has been built up. Four conclusions list below. 1. Gases in Kuche depression come from Triassic-Jurassic coal-measure source rocks. They are high-over maturity. Comparatively, the highest maturity area is Kelasu, next is Dabei area, Yinan area. 2. Kerogen thermal degradation is main reason of the dry gas in Kuche depression. Small part of dry gas comes from oil pyrolysis. VI 3.The K12 natural gas lays out some of hydro-gas character. Oil dissolved in the gas. Hydro-gas is also a factor making the gas drier and carbon isotope composition heavier. 4. The mechanism and genesis of KL2 gas pool list as below. Overpressure has being existed in Triassic-Jurassic source rocks since Keche period. Natural gases were expulsed by episode style from overpressure source rocks. Hetero-face was main migration style of gas, oil and water at that time. The fluids transferred the pressure of source rocks when they migrated and then separated when they got in reservoir. After that, natural gas migrated up and accumulated and formed with the techno-genesis. Tectonic extrusion made the natural gas overpressure continuously. When the pressure was up to the critical pressure, the C6-C7 composition in natural gas changed. The results were that relative abundance of alkane and aromatic decreased while cycloalkane and isoparaffin increased. There was lots of natural gas filling during every tectonic. The main factors of overpressure of natural gas were tectonic extrusion and fluid transferring pressure of source rocks. Well preservation was also important in the KL2 gas pool formation. The reserves of gas can satisfy the need of pipeline where is from west to east. IV A good idea of natural gas migration and accumulation modeling whose apparent character is real core and formation condition is suggested to model the physical process of gas formation. Following is the modeling results. 1. Modeling results prove that the gas accumulation rule under cap layer and gas fraction on migration path. 2. Natural gas migration as free phase is difficult in dense rock. 3. Natural gases accumulated easily in good physical properties reservoirs where are under the plugging layer. Under the condition of that permeability of rock is more than 1 * 10~(-3)μm~(-1), the more better the physical properties and the more bigger pore of rock, the more easier the gas accumulation in there. On the contrary, natural gas canonly migrate further to accumulate in good physical properties of rock. 4. Natural gas migrate up is different from that down. Under the same situation, the amount of gas migration up is lager than that of gas migration down and the distance of migration up is 3 times as that of migration down. 5. After gas leaks from dense confining layer, the ability of its dynamic plug-back decreased apparently. Gas lost from these arils easily. These confining layer can confine again only after geology condition changes. 6. Water-wetted and capillary-blocking rocks can't block water but gases generally. The result is that water can migrate continuously through blocking rocks but the gases stay under the blocking rocks then form in there. The experiments have proved the formation model of deep basin gas.

油藏动态模型和剩余油分布模式

This paper belong to national "973" technological project undertaken by Shengli Oilfield. Work area is composed of turbidite reservoir of S212 and delta reservoir of S283 of Sheng2 unit in Shengtuo Oilfield that has a 36 years water injection development history. Change of the macroscopic, microscopic and filterational parameters and its mechanism have been studied in the 4 water-cut stages i.e. the primary, moderate, high and supper-high stage by using multi-disciplinary theories and approaches, computer techniques and physical simulation comprehensively. Dynamic reservoir models to different water-cut stages have been established. The study of forming mechanism and distribution of residual oil revealed the main types and spatial distribution of residual oil in different water-cut stages and the distribution mode has also been built up. Macroscopic, microscopic and filterational parameters selecting principle, optimizing and selecting standard, matching standard and laws and related database of various dynamic parameters in different water-cut stages have been established, which laid good basis for revealing reservoir macroscopic, microscopic and filterational parameters' dynamic change and residual oil distribution. The study indicated that in general, the macroscopic, microscopic and filterational parameters will slowly increase and become better in both shallow turbidite and delta reservoirs with the increasing of water cut, but different reservoirs have their own characteristics and change laws. Parameters of I~2 unit, whose petrophysical properties are better, increase more quickly than 8~3, whose petrophysical properties are more unfavorable. The changes was relatively quickly in high water-cut stage, while relatively slowly from primary to moderate and from high to supper-high water-cut stage. This paper firstly put forward that reservoir macroscopic, microscopic and filterational parameters are controlled by dynamic geological function of reservoir fluid, which is considered the major reason of reservoir parameters' dynamic changes and residual oil formation and distribution during reservoir development. Physical simulation of filterational parameters verified that forming mechanism and distribution of residual oil in different water-cut stages are also controlled by dynamic geological function of reservoir fluid. The idea of fluid geological function during reservoir development developed the theory of development geology, and has important practical values. This paper firstly constructed dynamic geological and mathematical models and five modes of residual oil distribution in Shengtuo Oilfield, and achieved four-dimensional forecast of residual oil distribution in different watercut stages. Dynamic changes and mechanism of macroscopic, microscopic and fliterational parameters of reservoir and their change process have been revealed. Forecast of residual oil distribution has been achieved by computers. This paper established the related theories, approaches and techniques for residual oil study, characterization and in different water-cut stages, and realized dynamic forecast of residual oil. It gained remarkable economic benefit and social effect in guiding field development. These theories and techniques had important meaningfulness for residual oil prediction in the terrestrial faulted basins not only in Shengli Oilfield but also in the east of China. Furthermore, this study has developed the theory of development geology.

河流-三角洲储层剩余油分布模式及预测

Aim at the variousness and complexity of the spatial distribution of Remaining Oil in the fluvial and delta facies reservoir in paper. For example, in the La-Sa-Xing oilfield of Daqing, based on the research of the control factor and formation mechanization of block, single layer, interlayer and micromechanism, synthesizing the theories and methods of geology, well logging, reservoir engineering, artificial intelligence, physical simulation test , and computer multidisciplinary; Fully utilizing the material of geology, well logging, core well, dynamic monitor of oil and water well, and experimental analysis, from macro to micro, from quality to quantity, from indoor to workplace, we predicted the potentiality and distribution according to the four levels of Block, single layer, interlayer and micromechanism, and comprehensively summarized the different distribution pattern of remaining oil in the fluvial and delta facies reservoir This paper puts forward an efficient method to predict the remaining recoverable reserves by using the water flooding characteristic curve differential method and neutral network; for the first time utilizes multilevel fuzzy comprehensive judgment method and expert neutral network technology to predict the remaining oil distribution in the single layer? comprehensively takes advantage of reservoir flowing unit, indoor physical simulation test, inspection well core analysis and well-logging watered-out layer interpretation to efficiently predict the distribution of remaining oil; makes use of core analysis of different periods and indoor water driving oil test to study the micro distribution of remaining oil and the parameters varying law of reservoir substance properties, rock properties, wetting properties. Based on above, the remaining oil distribution predicting software is developed, which contains four levels of block, single layer, interlayer and micromechanism. This achievement has been used inLa-Sa-Xing oil field of Daqing and good results have been received.

大港油田孔南地区孔一段储层流动单元研究

The main reservoir type in the south of Dagang Oilfield is alluvial reservoir. In this paper, the reservoir structure model and the distribution of connected body and flow barrier were built on base of the study of high-resolution sequential stratigraphic skeleton and fine sedimentary microfacies on level of single sandbody. Utilizing the static and dynamic data synthetically and carrying out the comparision of the classification method for reservoir flow unit in different reservoir, the criterion, which can be used to classify the flow unit in first section of Kongdian formation of Kongnan area, was defined. The qualitative method of well-to-well correlation and the quantitative method of conditional simulation using multiple data are adopted to disclose the oil and water moving regulation in different flow unit and the distribution rule of remaining oil by physical simulation measure. A set of flow unit study method was formed that is suit for the Dagang Oilfield on account of the remaining oil production according to the flow unit. Several outstanding progresses was obtained in the following aspects:It is considered that the reservoir structure of Zao V iow oil group- Zao Vup4 layerand are jigsaw-puzzled reservoir, while ZaoVup3-ZaoVupi layers are labyrinth reservoir,which are studied on base of high-resolution sequential stratigraphic skeleton on the levelof single sandbody in first section of Kongdian formation of Kongnan area and accordingto the study of fine sedimentary microfacies and fault sealeing.When classifying the flow unit, only permeability is the basic parameter using thestatic and dynamic data and, and also different parameters should be chose or deleted, suchas porosity, effective thickness, fluid viscosity and so on, because of the weak or stronginterlayer heterogeneous and the difference of interlayer crude oil character.The method of building predicting-model of flow unit was proposed. This methodis according to the theories of reservoir sedimentology and high-resolution sequencestratigraphic and adopts the quantitative method of well-to well correlation and the quantitative method of stochastic simulation using integrateddense well data. Finally the 3-D predicting-model of flow unit and the interlay er distribution model in flow unit were built which are for alluvial fan and fan delta fades in first section of Kongdian formation of Kongnan area, and nine genetic model of flow unit of alluvial environment that spread in the space were proposed.(4) Difference of reservoir microscopic pore configuration in various flow units and difference of flow capability and oil displacement effect were demonstrated through the physical experiments such as nuclear magnetic resonance (NMR), constant rate mercury penetration, flow simulation and so on. The distribution of remaining oil in this area was predicted combining the dynamic data and numerical modeling based on the flow unit. Remaining oil production measure was brought up by the clue of flow unit during the medium and late course of the oilfield development.

Proceedings of the Fourth PHANTOM Users Group Workshop

This Report contains the proceedings of the Fourth Phantom Users Group Workshop contains 17 papers presented October 9-12, 1999 at MIT Endicott House in Dedham Massachusetts. The workshop included sessions on, Tools for Programmers, Dynamic Environments, Perception and Cognition, Haptic Connections, Collision Detection / Collision Response, Medical and Seismic Applications, and Haptics Going Mainstream. The proceedings include papers that cover a variety of subjects in computer haptics including rendering, contact determination, development libraries, and applications in medicine, path planning, data interaction and training.

Automatically Recovering Geometry and Texture from Large Sets of Calibrated Images

Three-dimensional models which contain both geometry and texture have numerous applications such as urban planning, physical simulation, and virtual environments. A major focus of computer vision (and recently graphics) research is the automatic recovery of three-dimensional models from two-dimensional images. After many years of research this goal is yet to be achieved. Most practical modeling systems require substantial human input and unlike automatic systems are not scalable. This thesis presents a novel method for automatically recovering dense surface patches using large sets (1000's) of calibrated images taken from arbitrary positions within the scene. Physical instruments, such as Global Positioning System (GPS), inertial sensors, and inclinometers, are used to estimate the position and orientation of each image. Essentially, the problem is to find corresponding points in each of the images. Once a correspondence has been established, calculating its three-dimensional position is simply a matter of geometry. Long baseline images improve the accuracy. Short baseline images and the large number of images greatly simplifies the correspondence problem. The initial stage of the algorithm is completely local and scales linearly with the number of images. Subsequent stages are global in nature, exploit geometric constraints, and scale quadratically with the complexity of the underlying scene. We describe techniques for: 1) detecting and localizing surface patches; 2) refining camera calibration estimates and rejecting false positive surfels; and 3) grouping surface patches into surfaces and growing the surface along a two-dimensional manifold. We also discuss a method for producing high quality, textured three-dimensional models from these surfaces. Some of the most important characteristics of this approach are that it: 1) uses and refines noisy calibration estimates; 2) compensates for large variations in illumination; 3) tolerates significant soft occlusion (e.g. tree branches); and 4) associates, at a fundamental level, an estimated normal (i.e. no frontal-planar assumption) and texture with each surface patch.

Accurate image capturing control of bottle caps based on iterative learning control and Kalman filtering

This paper investigates camera control for capturing bottle cap target images in the fault-detection system of an industrial production line. The main purpose is to identify the targeted bottle caps accurately in real time from the images. This is achieved by combining iterative learning control and Kalman filtering to reduce the effect of various disturbances introduced into the detection system. A mathematical model, together with a physical simulation platform is established based on the actual production requirements, and the convergence properties of the model are analyzed. It is shown that the proposed method enables accurate real-time control of the camera, and further, the gain range of the learning rule is also obtained. The numerical simulation and experimental results confirm that the proposed method can not only reduce the effect of repeatable disturbances but also non-repeatable ones.

Towards improving the framework for probabilistic forecast evaluation

The evaluation of forecast performance plays a central role both in the interpretation and use of forecast systems and in their development. Different evaluation measures (scores) are available, often quantifying different characteristics of forecast performance. The properties of several proper scores for probabilistic forecast evaluation are contrasted and then used to interpret decadal probability hindcasts of global mean temperature. The Continuous Ranked Probability Score (CRPS), Proper Linear (PL) score, and IJ Good’s logarithmic score (also referred to as Ignorance) are compared; although information from all three may be useful, the logarithmic score has an immediate interpretation and is not insensitive to forecast busts. Neither CRPS nor PL is local; this is shown to produce counter intuitive evaluations by CRPS. Benchmark forecasts from empirical models like Dynamic Climatology place the scores in context. Comparing scores for forecast systems based on physical models (in this case HadCM3, from the CMIP5 decadal archive) against such benchmarks is more informative than internal comparison systems based on similar physical simulation models with each other. It is shown that a forecast system based on HadCM3 out performs Dynamic Climatology in decadal global mean temperature hindcasts; Dynamic Climatology previously outperformed a forecast system based upon HadGEM2 and reasons for these results are suggested. Forecasts of aggregate data (5-year means of global mean temperature) are, of course, narrower than forecasts of annual averages due to the suppression of variance; while the average “distance” between the forecasts and a target may be expected to decrease, little if any discernible improvement in probabilistic skill is achieved.

Income inequality in Central America, Dominican Republic and Mexico: assessing the importance of individual and household characteristics

Includes bibliography

Interaction between recrystallization and strain-induced precipitation in a high Nb- and N-bearing austenitic stainless steel: influence of the interpass time

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

On Modular Design of Field Robotic Systems

Robots are needed to perform important field tasks such as hazardous material clean-up, nuclear site inspection, and space exploration. Unfortunately their use is not widespread due to their long development times and high costs. To make them practical, a modular design approach is proposed. Prefabricated modules are rapidly assembled to give a low-cost system for a specific task. This paper described the modular design problem for field robots and the application of a hierarchical selection process to solve this problem. Theoretical analysis and an example case study are presented. The theoretical analysis of the modular design problem revealed the large size of the search space. It showed the advantages of approaching the design on various levels. The hierarchical selection process applies physical rules to reduce the search space to a computationally feasible size and a genetic algorithm performs the final search in a greatly reduced space. This process is based on the observation that simple physically based rules can eliminate large sections of the design space to greatly simplify the search. The design process is applied to a duct inspection task. Five candidate robots were developed. Two of these robots are evaluated using detailed physical simulation. It is shown that the more obvious solution is not able to complete the task, while the non-obvious asymmetric design develop by the process is successful.

Effect of the cooling rate on microstructure and hardness of MAR-M247 Ni-based superalloy

The effect of cooling rate on the microstructure of MAR-M247 Ni-based superalloy was investigated via physical simulation of the casting process. Solidification experiments with cooling rates in the range of 0.25–10 K/s showed smooth temperature profiles with measured cooling rates matching the set values. The MAR-M247 showed cellular (0.25 K/s) and dendritic (1, 5 and 10 K/s) microstructures. Microconstituents also varied with cooling rates: γ/γ′ matrix with carbides and γ/γ′ eutectic at 0.25 K/s, γ/γ′ matrix with carbides at 1 K/s, and γ/γ′ matrix with carbides and γ/MC eutectic at 5 and 10 K/s. Moreover, the secondary dendritic arm spacing decreased and the hardness increased with the increase in the cooling rates.

Pulsed wall jet simulation of a stationary thunderstorm downburst, Part A: Physical structure and flow field characterization

A pulsed wall jet has been used to simulate the gust front of a thunderstorm downburst. Flow visualization, wind speed and surface pressure measurements were obtained. The characteristics of the hypothesized ring vortex of a full-scale downburst were reproduced at a scale estimated to be 1:3000.