Temporary Speed Hump Impact Evaluation, 2002

The main objective of this research was to evaluate the impact of temporary speed humps and speed tables on vehicle speeds, vehicle speed profiles, and traffic volumes along local and/or collector streets in several rural Iowa cities. A 25 mile per hour (mph) temporary speed hump and a 30 mph temporary speed table, both made of recycled rubber, were purchased to test the impact of temporary devices. Two cities volunteered and the speed hump/table was installed on two test streets in the city of Atlantic (Roosevelt Drive and Redwood Drive) and one test street in the city of Le Claire (Canal Shore Drive). The speed hump was installed first and then converted to a speed table. Each device was installed for a period of at least two weeks at the same location. Speed, volume, and resident opinion data were then collected and evaluated.

Inter-limb coordination and energy cost in swimming.

OBJECTIVES: This study investigated the relationship between inter-arm coordination and the energy cost of locomotion in front crawl and breaststroke and explored swimmers' flexibility in adapting their motor organization away from their preferred movement pattern. DESIGN: Nine front-crawlers performed three 300-m in front crawl and 8 breaststrokers performed three 200-m in breaststroke at constant submaximal intensity and with 5-min rests. Each trial was performed randomly in a different coordination pattern: freely chosen, 'maximal glide' and 'minimal glide'. Two underwater cameras videotaped frontal and side views to analyze speed, stroke rate, stroke length and inter-limb coordination. METHODS: In front crawl, inter-arm coordination was quantified by the index of coordination (IdC) and the leg beat kicks were counted. In breaststroke, four time gaps quantified the arm to leg coordination (i.e., time between leg and arm propulsions; time between beginning, 90° flexion and end of arm and leg recoveries). The energy cost of locomotion was calculated from gas exchanges and blood lactate concentration. RESULTS: In both front crawl and breaststroke, the freely chosen coordination corresponded to glide pattern and showed the lowest energy cost (12.8 and 17.1Jkg(-1)m(-1), respectively). Both front-crawlers and breaststrokers were able to reach 'maximal glide' condition (respectively, +35% and +28%) but not 'minimal glide' condition for front crawl. CONCLUSIONS: The freely chosen pattern appeared more economic because more trained. When coordination was constrained, the swimmers had higher coordination flexibility in breaststroke than in front crawl, suggesting that breaststroke coordination was easier to regulate by changing glide time.

In Search of Corporate Renewal: How to Benefit from Corporate Venturing?

Despite the rapid change in today's business environment there are relatively few studies about corporate renewal. This study aims for its part at filling that research gap by studying the concepts of strategy, corporate renewal, innovation and corporate venturing. Its purpose is to enhance our understanding of how established companies operating in dynamic and global environment can benefit from their corporate venturing activities. The theoretical part approaches the research problem in corporate and venture levels. Firstly, it focuses on mapping the determinants of strategy and suggests using industry, location, resources, knowledge, structure and culture, market, technology and business model to assess the environment and using these determinants to optimize speed and magnitude of change.Secondly, it concludes that the choice of innovation strategy is dependent on the type and dimensions of innovation and suggests assessing market, technology, business model as well as novelty and complexity related to each of them for choosing an optimal context for developing innovations further. Thirdly, it directsattention on processes through which corporate renewal takes place. On corporate level these processes are identified as strategy formulation, strategy formation and strategy implementation. On the venture level the renewal processes are identified as learning, leveraging and nesting. The theoretical contribution of this study, the framework of strategic corporate venturing, joins corporate and venture level management issues together and concludes that strategy processes and linking processes are the mechanism through which continuous corporate renewaltakes place. The framework of strategic corporate venturing proposed by this study is a new way to illustrate the role of corporate venturing as a purposefullybuilt, different view of a company's business environment. The empirical part extended the framework by enhancing our understanding of the link between corporate renewal and corporate venturing in its real life environment in three Finnish companies: Metso, Nokia and TeliaSonera. Characterizing companies' environmentwith the determinants of strategy identified in this study provided a structured way to analyze their competitive position and renewal challenges that they arefacing. More importantly the case studies confirmed that a link between corporate renewal and corporate venturing exists and found out that the link is not as straight forward as indicated by the theory. Furthermore, the case studies enhanced the framework by indicating a sequence according to which the processes work. Firstly, the induced strategy processes strategy formulation and strategy implementation set the scene for corporate venturing context and management processes and leave strategy formation for the venture. Only after that can strategies formed by ventures come back to the corporate level - and if found viable in the corporate level be formalized through formulation and implementation. With the help of the framework of strategic corporate venturing the link between corporaterenewal and corporate venturing can be found and managed. The suggested response to the continuous need for change is continuous renewal i.e. institutionalizing corporate renewal in the strategy processes of the company. As far as benefiting from venturing is concerned the answer lies in deliberately managing venturing in a context different to the mainstream businesses and establishing efficientlinking processes to exploit the renewal potential of individual ventures.

Energy efficiency parameters in variable speed drives

The main purpose of this thesis is to measure and evaluate how accurately the current energy saving calculation in ABB’s new variable speed drive ACS850 works. The main topic of this thesis is energy-efficiency parameters. At the beginning of this thesis centrifugal pump, squirrel cage motor and variable speed drive, including some equations related to them, are being introduced. Also methods of throttling control and variable speed drive control of centrifugal pumps are being introduced. These subjects are introduced because the energy saving calculation in ACS850 is related to the centrifugal pumps usually driven by squirrel cage motors. The theory also includes short section about specific energy of pumping. Before measurements the current energy saving calculation of ACS850 is being introduced and analyzed. The measurements part includes introduction of measuring equipment, measurement results, summary and analysis of the measurements. At the end of this thesis a proposal for an improvement to the current energy saving calculation is being introduced and few proposals are made for new energy-efficiency parameters, which could be added to variable speed drives. At the end are also thoughts

Kuituvuoto reikäsihdillä massan syöttövaiheessa

Diplomityön tarkoituksena oli kehittää tutkimuslaite, jolla pystyttäisiin tutkimaan sellumassan syöttötapahtumaa reikäsihdillä ja tarkastelemaan syöttöhetkellä tapahtuvaa kuituhäviötä. Laitteen suunnittelun ja valmistuksen tavoitteena oli myös saada tutkimuslaite mahdollisim-man modifioitavaksi (syöttöaukon koko, muoto ja erityyppiset reikäsihdit ja näiden vaikutukset sellukuitujen hävikkiin). Haluttiin myös mahdollisuus syöttötapahtuman kuvaamiseen esim. suurnopeuskameroin, joka otettiinkin huomioon laiteosia valittaessa (läpinäkyvä akryyli). Tutkimuslaitteen kestävyyttä erilaisissa prosessiolosuhteissa haluttiin korostaa (voidaan operoida laajalla pH ja lämpötila-alueilla, sekä syöttöpainetta voidaan muunnella). Diplomityön kirjallisuusosassa käsitellään kuituvuodon aiheuttamia haittoja, joista tärkein on taloudellinen menetys. Näiden lisäksi kirjallisuusosassa tarkastellaan pääpirteittäin pesume-netelmiä ja käydään läpi kuitusulpun suotautumiseen vaikuttavia tekijöitä. Diplomityöhön sisältyi tutkimuslaitteen suunnittelun ja valmistuksen lisäksi myös laitteen toi-mivuuden testaus. Testit suoritettiin pohjoismaisella koivusellulla. Koivusellu otettiin happi-vaiheen jälkeisen pesurin poistosta. Massalle suoritettiin KAPPA-luvun, SR-luvun, viskositee-tin ja syrjäytys -määritykset, sekä kuituanalyysi. Laitteella suoritettiin 7 %, 10 % ja 12 % sakeuksisten massojen koeajotestit. Suodokset otettiin talteen jatkotutkimuksiin, jossa niistä mitattiin kuituvuoto. 10 % suodokselle suoritettiin myös kuituanalyysi. Tuloksista nähtiin, että 7 % sakeuksinen massa antoi lähes nelinkertaisen kuituvuotomäärän 10 % sakeuksiseen massan syöttöön nähden.

AMB system for high-speed motors using automatic commissioning

The general trend towards increasing e ciency and energy density drives the industry to high-speed technologies. Active Magnetic Bearings (AMBs) are one of the technologies that allow contactless support of a rotating body. Theoretically, there are no limitations on the rotational speed. The absence of friction, low maintenance cost, micrometer precision, and programmable sti ness have made AMBs a viable choice for highdemanding applications. Along with the advances in power electronics, such as signi cantly improved reliability and cost, AMB systems have gained a wide adoption in the industry. The AMB system is a complex, open-loop unstable system with multiple inputs and outputs. For normal operation, such a system requires a feedback control. To meet the high demands for performance and robustness, model-based control techniques should be applied. These techniques require an accurate plant model description and uncertainty estimations. The advanced control methods require more e ort at the commissioning stage. In this work, a methodology is developed for an automatic commissioning of a subcritical, rigid gas blower machine. The commissioning process includes open-loop tuning of separate parts such as sensors and actuators. The next step is to apply a system identi cation procedure to obtain a model for the controller synthesis. Finally, a robust model-based controller is synthesized and experimentally evaluated in the full operating range of the system. The commissioning procedure is developed by applying only the system components available and a priori knowledge without any additional hardware. Thus, the work provides an intelligent system with a self-diagnostics feature and an automatic commissioning.

Methodological approaches to planar and volumetric scintigraphic imaging of small volume targets with high spatial resolution and sensitivity

Single-photon emission computed tomography (SPECT) is a non-invasive imaging technique, which provides information reporting the functional states of tissues. SPECT imaging has been used as a diagnostic tool in several human disorders and can be used in animal models of diseases for physiopathological, genomic and drug discovery studies. However, most of the experimental models used in research involve rodents, which are at least one order of magnitude smaller in linear dimensions than man. Consequently, images of targets obtained with conventional gamma-cameras and collimators have poor spatial resolution and statistical quality. We review the methodological approaches developed in recent years in order to obtain images of small targets with good spatial resolution and sensitivity. Multipinhole, coded mask- and slit-based collimators are presented as alternative approaches to improve image quality. In combination with appropriate decoding algorithms, these collimators permit a significant reduction of the time needed to register the projections used to make 3-D representations of the volumetric distribution of target’s radiotracers. Simultaneously, they can be used to minimize artifacts and blurring arising when single pinhole collimators are used. Representation images are presented, which illustrate the use of these collimators. We also comment on the use of coded masks to attain tomographic resolution with a single projection, as discussed by some investigators since their introduction to obtain near-field images. We conclude this review by showing that the use of appropriate hardware and software tools adapted to conventional gamma-cameras can be of great help in obtaining relevant functional information in experiments using small animals.

THE INFLUENCE OF LENGTH CHANGE SPEED AND DIRECTION ON DYNAMIC FUNCTION POTENTIATION IN FAST MOUSE MUSCLE

The purpose of this study was to test the hypothesis that the potentiation of dynamic function was dependent upon both length change speed and direction. Mouse EDL was cycled in vitro (25º C) about optimal length (Lo) with constant peak strain (± 2.5% Lo) at 1.5, 3.3 and 6.9 Hz before and after a conditioning stimulus. A single pulse was applied during shortening or lengthening and peak dynamic (concentric or eccentric) forces were assessed at Lo. Stimulation increased peak concentric force at all frequencies (range: 19 ± 1 to 30 ± 2%) but this increase was proportional to shortening speed, as were the related changes to concentric work/power (range: -15 ± 1 to 39 ± 1 %). In contrast, stimulation did not increase eccentric force, work or power at any frequency. Thus, results reveal a unique hysteresis like effect for the potentiation of dynamic output wherein concentric and eccentric forces increase and decrease, respectively, with work cycle frequency.

THE INFLUENCE OF LENGTH CHANGE SPEED AND DIRECTION ON DYNAMIC FUNCTION POTENTIATION IN FAST MOUSE MUSCLE

The purpose of this study was to test the hypothesis that the potentiation of dynamic function was dependent upon both length change speed and direction. Mouse EDL was cycled in vitro (250 C) about optimal length (Lo) with constant peak strain (± 2.5% Lo) at 1.5,3.3 and 6.9 Hz before and after a conditioning stimulus. A single pulse was applied during shortening or lengthening and peak dynamic (concentric or eccentric) forces were assessed at Lo. Stimulation increased peak concentric force at all frequencies (range: 19±1 to 30 ± 2%) but this increase was proportional to shortening speed, as were the related changes to concentric work/power (range: -15 ± 1 to 39 ± 1 %). In contrast, stimulation did not increase eccentric force, work or power at any frequency. Thus, results reveal a unique hysteresis like effect for the potentiation of dynamic output wherein concentric and eccentric forces increase and decrease, respectively, with work cycle frequency.

An efficient scheme for the evaluation of coding performance of high speed links incorporating joint error behaviour based on Monte Carlo Method

While channel coding is a standard method of improving a system’s energy efficiency in digital communications, its practice does not extend to high-speed links. Increasing demands in network speeds are placing a large burden on the energy efficiency of high-speed links and render the benefit of channel coding for these systems a timely subject. The low error rates of interest and the presence of residual intersymbol interference (ISI) caused by hardware constraints impede the analysis and simulation of coded high-speed links. Focusing on the residual ISI and combined noise as the dominant error mechanisms, this paper analyses error correlation through concepts of error region, channel signature, and correlation distance. This framework provides a deeper insight into joint error behaviours in high-speed links, extends the range of statistical simulation for coded high-speed links, and provides a case against the use of biased Monte Carlo methods in this setting

Effects of gender on stroke rates, critical speed and velocity of a 30-min swim in young swimmers

Our objective was to analyze the effect of gender on the relationship between stroke rates corresponding to critical speed (SRCS) and maximal speed of 30 min (SRS30) in young swimmers. Twenty two males (GM1) (Age = 15.4 ± 2.1 yr., Body mass = 63.7 ± 12.9 kg, Stature = 1.73 ± 0.09 m) and fourteen female (GF) swimmers (Age = 15.1 ± 1.6 yr., Body mass = 58.3 ± 8.8 kg, Stature = 1.65 ± 0.06 m) were studied. A subset of males (GM2) was matched to the GF by their velocity for a 30 min swim (S30). The critical speed (CS) was determined through the slope of the linear regression line between the distances (200 and 400 m) and participant's respective times. CS was significantly higher than S30 in males (GM1 - 1.25 and 1.16 and GM2 - 1.21 and 1.12 m·s-1) and females (GF - 1.15 and 1.11 m·s-1). There was no significant difference between SRCS and SRS30 in males (GM1 - 34.16 and 32.32 and GM2 - 34.67 and 32.46 cycle·s-1, respectively) and females (GF - 34.18 and 33.67 cycle·s-1-1, respectively). There was a significant correlation between CS and S30 (GM1 - r = 0.89, GF - r = 0.94 and GM2 - r = 0.90) and between SRCS and SRS30 (GM1 - r = 0.89, GF - r = 0.80 and GM2 - r = 0.88). Thus, the relationship between SRCS and SRS30 is not influenced by gender, in swimmers with similar and different aerobic capacity levels. ©Journal of Sports Science and Medicine (2007).

Speed estimation for induction motor using neural networks method

This work presents an alternative approach based on neural network method in order to estimate speed of induction motors, using the measurement of primary variables such as voltage and current. Induction motors are very common in many sectors of the industry and assume an important role in the national energy policy. The nowadays methodologies, which are used in diagnosis, condition monitoring and dimensioning of these motors, are based on measure of the speed variable. However, the direct measure of this variable compromises the system control and starting circuit of an electric machinery, reducing its robustness and increasing the implementation costs. Simulation results and experimental data are presented to validate the proposed approach. © 2003-2012 IEEE.

Evaluation of factors affecting speed perception in a driving simulator

The present study was conducted to determine the effects of different variables on the perception of vehicle speeds in a driving simulator. The motivations of the study include validation of the Michigan Technological University Human Factors and Systems Lab driving simulator, obtaining a better understanding of what influences speed perception in a virtual environment, and how to improve speed perception in future simulations involving driver performance measures. Using a fixed base driving simulator, two experiments were conducted, the first to evaluate the effects of subject gender, roadway orientation, field of view, barriers along the roadway, opposing traffic speed, and subject speed judgment strategies on speed estimation, and the second to evaluate all of these variables as well as feedback training through use of the speedometer during a practice run. A mixed procedure model (mixed model ANOVA) in SAS® 9.2 was used to determine the significance of these variables in relation to subject speed estimates, as there were both between and within subject variables analyzed. It was found that subject gender, roadway orientation, feedback training, and the type of judgment strategy all significantly affect speed perception. By using curved roadways, feedback training, and speed judgment strategies including road lines, speed limit experience, and feedback training, speed perception in a driving simulator was found to be significantly improved.

Measuring population mobility speed from space

Ad-hoc population dynamics in Krugman’s type core and periphery models adjust population share of a region, based on its real wage rate deviation from national average, at pre-specified speed of population mobility. Whereas speed of population mobility is expected to be different across countries, for geographical, cultural, technological, etc. reasons, one common speed is often applied in theoretical and simulation analysis, due to spatially patchy, and temporally infrequent, availability of sub-national regional data. This article demonstrates how, increasingly available, high definition spatio-temporal remote-sensing data, and their by-products, can be used to measure speed of population mobility in national and sub-national level.

A comparative analysis of visual strategy in elite and amateur handball goalkeepers

The aim of the present study was to analyze the visual strategies prior to a throw from 7 metres in elite and amateur handball goalkeepers. To this end we analyzed the visual fixations in number and order of 10 goalkeepers (29.7±5.4 years; 14.7±8.6 years of experience), 3 elite and 7 amateurs, during the life size projection of 14 different throws, made by different players. During each throw the movement of the eyeballs, the dilation of the pupil (pupillometry) and the subject?s blinking were recorded thanks to a technological system which permitted eye tracking with high speed cameras, and the subsequent presentation of the visual data for each action studied. The elite goalkeepers performed a greater number of visual fixations than the amateur goalkeepers, revealing large and significant differences. Equally the priority zones observed were differed, with the amateur goalkeepers fixating more on the thrower?s face, and the elite goalkeepers paying more attention to the area of the arm/ball. It can therefore be inferred that elite goalkeepers have a greater perceptive capacity and also use different visual strategies from the amateur goalkeepers.