Modelling and simulation of biomass gasification in a circulating fluidized bed reactor

Computational Fluid Dynamics (CFD) has found great acceptance among the engineering community as a tool for research and design of processes that are practically difficult or expensive to study experimentally. One of these processes is the biomass gasification in a Circulating Fluidized Bed (CFB). Biomass gasification is the thermo-chemical conversion of biomass at a high temperature and a controlled oxygen amount into fuel gas, also sometime referred to as syngas. Circulating fluidized bed is a type of reactor in which it is possible to maintain a stable and continuous circulation of solids in a gas-solid system. The main objectives of this thesis are four folds: (i) Develop a three-dimensional predictive model of biomass gasification in a CFB riser using advanced Computational Fluid Dynamic (CFD) (ii) Experimentally validate the developed hydrodynamic model using conventional and advanced measuring techniques (iii) Study the complex hydrodynamics, heat transfer and reaction kinetics through modelling and simulation (iv) Study the CFB gasifier performance through parametric analysis and identify the optimum operating condition to maximize the product gas quality. Two different and complimentary experimental techniques were used to validate the hydrodynamic model, namely pressure measurement and particle tracking. The pressure measurement is a very common and widely used technique in fluidized bed studies, while, particle tracking using PEPT, which was originally developed for medical imaging, is a relatively new technique in the engineering field. It is relatively expensive and only available at few research centres around the world. This study started with a simple poly-dispersed single solid phase then moved to binary solid phases. The single solid phase was used for primary validations and eliminating unnecessary options and steps in building the hydrodynamic model. Then the outcomes from the primary validations were applied to the secondary validations of the binary mixture to avoid time consuming computations. Studies on binary solid mixture hydrodynamics is rarely reported in the literature. In this study the binary solid mixture was modelled and validated using experimental data from the both techniques mentioned above. Good agreement was achieved with the both techniques. According to the general gasification steps the developed model has been separated into three main gasification stages; drying, devolatilization and tar cracking, and partial combustion and gasification. The drying was modelled as a mass transfer from the solid phase to the gas phase. The devolatilization and tar cracking model consist of two steps; the devolatilization of the biomass which is used as a single reaction to generate the biomass gases from the volatile materials and tar cracking. The latter is also modelled as one reaction to generate gases with fixed mass fractions. The first reaction was classified as a heterogeneous reaction while the second reaction was classified as homogenous reaction. The partial combustion and gasification model consisted of carbon combustion reactions and carbon and gas phase reactions. The partial combustion considered was for C, CO, H2 and CH4. The carbon gasification reactions used in this study is the Boudouard reaction with CO2, the reaction with H2O and Methanation (Methane forming reaction) reaction to generate methane. The other gas phase reactions considered in this study are the water gas shift reaction, which is modelled as a reversible reaction and the methane steam reforming reaction. The developed gasification model was validated using different experimental data from the literature and for a wide range of operating conditions. Good agreement was observed, thus confirming the capability of the model in predicting biomass gasification in a CFB to a great accuracy. The developed model has been successfully used to carry out sensitivity and parametric analysis. The sensitivity analysis included: study of the effect of inclusion of various combustion reaction; and the effect of radiation in the gasification reaction. The developed model was also used to carry out parametric analysis by changing the following gasifier operating conditions: fuel/air ratio; biomass flow rates; sand (heat carrier) temperatures; sand flow rates; sand and biomass particle sizes; gasifying agent (pure air or pure steam); pyrolysis models used; steam/biomass ratio. Finally, based on these parametric and sensitivity analysis a final model was recommended for the simulation of biomass gasification in a CFB riser.

Nuovi processi catalitici per la produzione di syngas

The study of the combined Steam/Dry Reforming (S/DR) process for the production of syngas (CO + H2) from clean biogas was carried out using Ni/Ir bimetallic catalysts on Mg and Al mixed-oxides, obtained by calcination of hydrotalcite-type precursors (Ht) prepared by co-precipitation. The presence of small amounts of Ir promoted the catalytic activity and limited the deactivation phenomena through the formation of a bimetallic alloy, which does the catalyst very active even at lowest temperature and in lack of steam. By integrating a High Temperature–WGS unit (HTS) after the S/DR reactor it was possible to increase the H2 yield of the process. The performance of the Zn/Al/Cu-based catalyst was improved using a templating agent during the synthesis of the catalyst, which increased the catalyst’s structural properties and activity especially at lowest temperatures and at highest contact times. Finally, starting from the laboratory data, it was possible to simulate the S/DR process on industrial scale, evaluating its scalability and environmental impact. The results showed that, using the S/DR technology instead of the current processes, it was possible to reduce the energy costs and the atmospheric emissions of the plant.

Analisi del ciclo di vita di un processo industriale innovativo per la produzione di syngas da biogas

Una delle metodologie che negli ultimi tempi viene utilizzata più frequentemente per la valutazione ambientale di prodotti, processi e servizi è detta LCA, Life Cycle Assessment: essa valuta l’impatto ambientale associato ad un processo o ad un prodotto considerando tutto il suo ciclo di vita. Nel presente elaborato di tesi la metodologia è applicata ad un processo chimico industriale in fase di studio su scala di laboratorio presso il Dipartimento di Chimica Industriale dell’Università di Bologna, che prevede la sintesi di syngas a partire da biogas tramite le reazioni di dry reformng (DR) e steam refroming (SR). Tale processo è stato studiato poiché a livello teorico presenta i seguenti vantaggi: l’utilizzo di biogas come materia prima (derivante dalla digestione anaerobica dei rifiuti), lo sfruttamento dell’anidride carbonica presente nel biogas e l’utilizzo di un solo reattore anziché due. Il processo viene analizzato attraverso due diversi confronti: in primo luogo è comparato con processi con tecnologie differenti che producono il medesimo prodotto (syngas); in secondo luogo è paragonato a processi che impiegano la stessa materia prima (biogas), ottenendo prodotti differenti. Nel primo confronto i processi confrontati sono uno scenario di Autothermal reforming (ATR) e uno scenario che prevede DR e SR in due reattori separati; nel secondo confronto i prodotti che si ottengono sono: energia termica ed elettrica attraverso un sistema CHP, biometano con un sistema di upgrading del biogas, energia e biometano (CHP + upgrading) ed infine metanolo prodotto da syngas (generato dal processo studiato). Per il primo confronto è risultato che lo scenario che porta ad un minore impatto ambientale è il processo studiato dall'università di Bologna, seguito dallo Scenario con DR e SR in reattori separati ed infine dal processo di ATR. Per quanto concerne il secondo confronto lo scenario migliore è quello che produce biometano, mentre quello che produce metanolo è al terzo posto.

Catalizzatori strutturati per valorizzazione di biogas a syngas

Il presente lavoro di tesi è stato realizzato all’interno del programma Overseas, per cui è stata realizzata una collaborazione tra il Dipartimento di Chimica Industriale “Toso Montanari” (Chimind) dell’Università di Bologna e l’Instituto de Investigaciones en Catálisis y Petroquímica (Incape) dell’Università del Litoral di Santa Fe. Nel lavoro viene riportato lo studio di catalizzatori strutturati a base di Rh-CeO2, Rh/ZnAl2O4 e Rh/Al2O3, supportati su schiume NiCrAl, dei quali verrà valutata l’attività catalitica rispetto alla reazione di dry reforming del metano. La preparazione dei catalizzatori strutturati è stata eseguita utilizzando due diverse tecniche, dip-coating e elettrodeposizione. L’obbiettivo del lavoro è stato valutare il metodo di sintesi più adatto al supporto utilizzato. Le prove catalitiche sono state eseguite a 750°C, P atmosferica, rapporto CH4:CO2 1:1 con tempo di reazione di 2h. Dai risultati ottenuti dalle prove effettuate i catalizzatori sono risultati attivi, in particolare il supporto di CeO2 risulta già attivo per la reazione, soprattutto per quanto riguarda la conversione del metano. Tuttavia, la presenza di Rh migliora la conversione dei reagenti ed il rapporto H2/CO. La presenza di Zn, sul catalizzatore Rh/ZnAl2O4 va a peggiorare le prestazioni catalitiche, abbassando in particolare la conversione della CO2. In generale i catalizzatori ricoperti mediante elettrodeposizione mostrano attività catalitica più elevata. Dallo studio sulla superficie del catalizzatore Rh-CeO2 ridotto tramite XPS è emersa la presenza di Rh(0). Tuttavia, indifferentemente dalla tecnica di sintesi utilizzata, dall’ossido del supporto e dalla quantità di fase attiva, tutti i catalizzatori hanno sviluppato massicce quantità di carbonio filamentoso di dimensioni nanometriche, che hanno portato alla disgregazione e alla perdita di parte del coating.

Functional nanostructured catalysts based on the niobates to the dry methane reforming and ethylene homologation reactions

Catalytic activity and selectivity of niobate-based nanostructured materials were investigated. Dry methane reforming (DMR) and ethylene homologation reaction (EHR) were selected as test reactions. KSr 2Nb5O15, Sr2NaNb5O 15 and NaSr2(NiNb4)O15 δ niobate powders were prepared by the high energy ball milling method and calcined in a reductor atmosphere. N2 adsorption isotherms, X-ray diffraction and infrared spectroscopy characterization was performed. Hydrogen pretreated niobates showed from low to moderate catalytic initial activity in DMR's test, nevertheless the materials were deactivated rapidly and the kinetic parameters associated to deactivation were estimated. Otherwise, non-treated catalysts showed a high initial activity in EHR's test and KSr2Nb 5O15 catalyst requires 24 h to the total deactivation with a high selectivity to form propylene. A reaction mechanism to the propylene formation is discussed. © 2012 Elsevier Ltd. All rights reserved.

CO2 reforming of methane on Ni catalysts: Effects of the support phase and preparation technique

The effects of the support phase and catalyst preparation methods on catalytic activity and carbon deposition were systematically investigated over nickel catalysts supported on Al2O3, SiO2 and MgO for the reforming reaction of methane with carbon dioxide. It is found that the pore structure of the support and metal-support interaction significantly affected the catalytic activity and coking resistance. Catalyst with well-developed porosity exhibited higher catalytic activity. Strong interaction between metal and the support made the catalyst more resistant to sintering and coking, thus resulting in a longer time of catalyst stability. (C) 1998 Elsevier Science B.V.

Reforming of methane with carbon dioxide over Ni/Al2O3 catalysts: Effect of nickel precursor

The catalytic activities of Ni/gamma-Al2O3 catalysts prepared using different nickel precursor compounds were studied for the reaction of methane reforming with CO2. It is found that the nickel precursor employed in the catalyst preparation plays an important role. The catalyst based on nickel nitrate exhibited higher catalytic activity and stability over a 24-h test period than the other two catalysts derived from nickel chloride and nickel acetylacetonate. A comprehensive characterisation of the catalysts showed that the weak interaction between Ni particles and gamma-Al2O3 resulted in more active sites on Ni nitrate-derived Ni/gamma-Al2O3 catalyst. Coking studies showed that carbon deposition on Ni catalysts derived from inorganic precursors (nitrate and chloride) were more severe than on the organic precursor-derived catalyst. However, the Ni nitrate-derived catalyst was found to have the highest stability (or lowest deactivation rate) mainly due to the active carbon species (-C-C-) of the resulting graphitic structure and their close contact with the metal particles. In contrast, the carbon formed on Ni-AA catalyst (from Ni acetylacetonate) is dominated by inactive -CO-C- species, thus leading to a rapid accumulation of carbon in this catalyst and more severe deactivation. (C) 1998 Elsevier Science B.V.

Preparation, characterization, and catalytic properties of clay-based nickel catalysts for methane reforming

Naturally occurring clays and pillared clays are used as supports of nickel catalysts for the methane reforming reaction with carbon dioxide to synthesis gas. The structural and textural characteristics of the supports and catalysts are systematically examined by N-2 adsorption/desorption and X-ray diffraction (XRD) techniques. It is found that the pore structures and surface properties of supports greatly affect the catalytic activities of the catalysts prepared. The catalysts supported on the mesoporous clays or pillared clays are obviously superior to those on microporous supports because the mesoporous supports are highly thermal stable compared to the microporous ones. It is found that introducing lanthanum to the supports can improve the catalyst basicity and thus enhance the catalytic activities of these catalysts. Deactivation of catalysts prepared and factors influencing their stability are also discussed. (C) 1998 Academic Press.

Thermogravimetric analysis of carbon deposition over Ni/gamma-Al2O3 catalysts in carbon dioxide reforming of methane

Carbon formation on Ni/gamma-Al2O3 catalysts and its kinetics during methane reforming with carbon dioxide was studied in the temperature range of 500-700 degrees C using a thermogravimetric analysis technique. The activation energies of methane cracking, carbon gasification in CO2, as well as carbon deposition in CO2-CH4 reforming were obtained. The results show that the activation energy for carbon gasification is larger than that of carbon formation in methane cracking and that the activation energy of coking in CO2-CH4 reforming is also larger than that of methane decomposition to carbon. The dependencies of coking rate on partial pressures of CH4 and CO2 indicate that methane decomposition is the main route for carbon deposition. A mechanism and kinetic model for carbon deposition is proposed.

Role of CeO2 in Ni/CeO2-Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on gamma-Al2O3, CeO2 and CeO2-A1(2)O(3) systems were tested for catalytic CO2 reforming of methane into synthesis gas. Ni/CeO2-Al2O3 catalysts showed much better catalytic performance than either CeO2- or gamma-Al2O3-supported Ni catalysts. CeO2 as a support for Ni catalysts produced a strong metal-support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO2 had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/gamma-Al2O3 catalysts for this reaction. A weight loading of 1-5 wt% CeO2 was found to be the optimum. Ni catalysts with CeO2 promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO2-promoted catalysts are attributed to the oxidative properties of CeO2. (C) 1998 Elsevier Science B.V. All rights reserved.