Material effects on stress-induced defect generation in trenched silicon-on-insulator structures

We have investigated the influence of the material properties of the silicon device layer on the generation of defects, and in particular slip dislocations, in trenched and refilled fusion-bonded silicon-on-insulator structures. A strong dependence of the ease of slip generation on the type of dopant species was observed, with the samples falling into three basic categories; heavily boron-doped silicon showed ready slip generation, arsenic and antimony-doped material was fairly resistant to slip, while silicon moderately or lightly doped with phosphorous or boron gave intermediate behavior. The observed behavior appears to be controlled by differences in the dislocation generation mechanism rather than by dislocation mobility. The introduction of an implanted buried layer at the bonding interface was found to result in an increase in slip generation in the silicon, again with a variation according to the dopant species. Here, the greatest slip occurred for both boron and antimony-implanted samples. The weakening of the implanted material may be related to the presence of a band of precipitates observed in the silicon near the bonding interface. (C) 2001 The Electrochemical Society.

Nuclear fuel cycles: interfaces with the environment

The waste materials generated in the nuclear fuel cycle are very varied,ranging from the tailings arising from mining and processing uranium ore, depleted uranium in a range of chemical forms, to a range of process wastes of differing activities and properties. Indeed, the wastes generated are intimately linked to the options selected in operating the nuclear fuel cycle, most obviously to the management of spent fuel. An open fuel cycle implies the disposal of highly radioactive spent fuel, whereas a closed fuel cycle generates a complex array of waste streams. On the other hand, a closed fuel cycle offers options for waste management, for example reduction in highly active waste volume, decreased radiotoxicity, and removal of fissile material. Many technological options have been proposed or explored, and each brings its own particular mix of wastes and environmental challenges.

Scattering of electromagnetic waves by rough interfaces and inhomogeneous layers

We consider a two-dimensional problem of scattering of a time-harmonic electromagnetic plane wave by an infinite inhomogeneous conducting or dielectric layer at the interface between semi-infinite homogeneous dielectric half-spaces. The magnetic permeability is assumed to be a fixed positive constant. The material properties of the media are characterized completely by an index of refraction, which is a bounded measurable function in the layer and takes positive constant values above and below the layer, corresponding to the homogeneous dielectric media. In this paper, we examine only the transverse magnetic (TM) polarization case. A radiation condition appropriate for scattering by infinite rough surfaces is introduced, a generalization of the Rayleigh expansion condition for diffraction gratings. With the help of the radiation condition the problem is reformulated as an equivalent mixed system of boundary and domain integral equations, consisting of second-kind integral equations over the layer and interfaces within the layer. Assumptions on the variation of the index of refraction in the layer are then imposed which prove to be sufficient, together with the radiation condition, to prove uniqueness of solution and nonexistence of guided wave modes. Recent, general results on the solvability of systems of second kind integral equations on unbounded domains establish existence of solution and continuous dependence in a weighted norm of the solution on the given data. The results obtained apply to the case of scattering by a rough interface between two dielectric media and to many other practical configurations.

Vanadium oxide-porphyrin nanocomposites as gas sensor interfaces for probing low water content in ethanol

Vanadium pentoxide xerogels (VXG) incorporating meso(3- and 4-pyridyl)porphyrin cobalt(III) species coordinated to four [Ru(bipy)(2)Cl](+) complexes were employed as gas sensing materials capable of detecting small amounts of water in commercial ethanol and fuel supplies. According to their X-ray diffraction data, the original VXG lamellar framework was maintained in the nanocomposite material, but the interlamellar distance increased from 11.7 to 15.2 angstrom, reflecting the intercalation of the porphyrin species into the vanadium pentoxide matrix. The films generated by direct deposition of the nanocomposite aqueous suspensions exhibited good electrical and electrochemical performance for application in resistive sensors. The analysis of water in ethanol and fuels was carried out successfully using an especially designed electric setup incorporating a laminar gas flow chamber and interdigitated gold electrodes coated with the nanocomposites. (C) 2010 Elsevier B.V. All rights reserved.

Ensaios de rampa para estudo da resistência de interfaces solo-geossintético

O emprego de materiais geossintéticos em obras de Engenharia Civil tem sido freqüente nas últimas décadas. Os projetos e obras exigem uma maior compreensão do comportamento de interação solo-geossintético. Este mecanismo de interação é complexo e depende das propriedades dos materiais envolvidos. Os parâmetros de resistência da interface são determinados em ensaios de campo, menos usuais, e ensaios de laboratório, dos quais destacam-se os ensaios de arrancamento e cisalhamento direto, e, mais recentemente, ensaios de rampa. A escolha do ensaio mais adequado é função do tipo de geossintético e da sua solicitação na massa de solo. Este trabalho teve como finalidade geral desenvolver um equipamento de grande escala, capaz de executar em uma mesma estrutura os principais ensaios de resistência de interfaces solo-geossintético. Especificamente, o objetivo principal consistiu em habilitar o equipamento para a realização de ensaios de rampa. O equipamento de rampa teve seu desempenho avaliado através de ensaios preliminares que permitiram avaliar a acurácia dos resultados e a adequação da metodologia de preparação dos corpos de prova e procedimento de ensaio O programa experimental envolveu ensaios de rampa em quatro tipos distintos de interface: solo-solo, solo-geotêxtil, solo-geogrelha e solo-geomembrana. Os ensaios de interface solo-solo permitiram a avaliação do equipamento, a comparação com ensaios convencionais de cisalhamento direto e a obtenção dos parâmetros de resistência para a determinação das eficiências de interação das interfaces em termos de adesão e ângulo de atrito. Os ensaios de interface sologeossintéticos indicaram um comportamento de resistência semelhante ao reportado na literatura e condicionado pelo tipo de material.

Uso do método das interfaces coesivas na análise da simulação do comportamento de fratura em materiais frágeis

Este trabalho apresenta uma abordagem numérica da fratura baseada no Método dos Elementos Finitos na qual são considerados materiais frágeis como objeto de estudo. As simulações realizadas são possíveis através de um algoritmo computacional que consiste na implementação de molas entre as faces dos elementos finitos. Esta composição constitui o método denominado Interfaces Coesivas. As molas fornecem o efeito de coesão e é representado por leis constitutivas do tipo bi-linear. Sua descrição é apresentada, bem como sua implementação na análise. Tanto o modo I como o modo II de ruptura são considerados. Com o objetivo de verificar o presente modelo com outros resultados e soluções, são analisados exemplos numéricos e experimentais extraídos da literatura. Tais exemplos tratam da nucleação, propagação e eventuais paradas de trincas em peças estruturais submetidas aos mais diversos carregamentos e condições de contorno. É ainda discutido como os parâmetros de fratura do material interferem no processo de ruptura. Uma tentativa é feita de determinar estes parâmetros, em especial no caso de concreto.

Filmes nanoestruturados aplicados ao sistema de língua eletrônica: um estudo de interfaces

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Nas ondas da informação: interfaces entre o pensamento geográfico e a geografia econômica para o estudo das telecomunicações no Brasil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Confocal laser scanning microscopy investigation of bond interfaces involved in fiber glass post cementation

Objective: This confocal microscopy study evaluated the cement/dentin and cement/post interfaces along theroot canalwallswhenfiberglasspostswerebonded to dentin using different types of cements. Material & Methods: Thirty endodontically treated premolars were divided into 3 groups according to the adhesive materials used in the bonding procedure: Prime & Bond 2.1/Self Cure + Enforce, RelyX Unicem and RelyX Luting. Rhodamine B dye was incorporated in the luting materials for the cementation of the fiber glass posts (Exacto, Angelus) to dentin. Three transversal slices (apical, middle and coronal) were examined under confocal laser scanning microscopy. Statistical analysis was performed using the Kappa, Kruskal-Wallis and Dunnet tests, in a significance level of 5%. Results: The Prime & Bond 2.1/Self Cure + Enforce presented a uniform formation of tags in the dentin but gaps in the cement/dentin interface. The RelyX Unicem and RelyX Luting presented an adhesive interface with a fewer amount of gaps, but showed shorter tag formation than the Enforce system. All cements presented the same pattern of bubbles inside the cements. The RelyX Luting presented a greater amount of cracks inside the cement in comparison with the other cements in the coronal third, while no difference was observed between RelyX Unicem and Enforce. The RelyX Luting showed the lowest quantity of cement penetration into the post. Conclusion: In general, the quality of bonding interfaces of fiber posts luted to root canals was affected by both location and type of cement.

Advanced SPM studies on the growth of ultrathin films of organic semiconductors at metal and dielectric interfaces

Many studies on the morphology, molecular orientation, device performance, substrate nature and growth parameter dependence have been carried out since the proposal of Sexithiophene (6T) for organic electronics [ ] However, these studies were mostly performed on films thicker than 20nm and without specifically addressing the relationship between morphology and molecular orientation within the nano and micro structures of ultrathin films of 0-3 monolayers. In 2004, the observation that in OFETs only the first few monolayers at the interface in contact with the gate insulator contribute to the charge transport [ ], underlined the importance to study submonolayer films and their evolution up to a few monolayers of thickness with appropriate experimental techniques. We present here a detailed Non-contact Atomic Force Microscopy and Scanning Tunneling Microscopy study on various substrates aiming at the investigation of growth mechanisms. Most reported similar studies are performed on ideal metals in UHV. However it is important to investigate the details of organic film growth on less ideal and even technological surfaces and device testpatterns. The present work addresses the growth of ultra thin organic films in-situ and quasi real-time by NC-AFM. An organic effusion cell is installed to evaporate the organic material directly onto the SPM sample scanning stage.

Adsorption of macromolecules on interfaces studied by isothermal titration calorimetry

The mixing of nanoparticles with polymers to form composite materials has been applied for decades. They combine the advantages of polymers (e.g., elasticity, transparency, or dielectric properties) and inorganic nanoparticles (e.g., specific absorption of light, magneto resistance effects, chemical activity, and catalysis etc.). Nanocomposites exhibit several new characters that single-phase materials do not have. Filling the polymeric matrix with an inorganic material requires its homogeneous distribution in order to achieve the highest possible synergetic effect. To fulfill this requirement, the incompatibility between the filler and the matrix, originating from their opposite polarity, has to be resolved. A very important parameter here is the strength and irreversibility of the adsorption of the surface active compound on the inorganic material. In this work the Isothermal titration calorimetry (ITC) was applied as a method to quantify and investigate the adsorption process and binding efficiencies in organic-inorganic–hybrid-systems by determining the thermodynamic parameters (ΔH, ΔS, ΔG, KB as well as the stoichiometry n). These values provide quantification and detailed understanding of the adsorption process of surface active molecules onto inorganic particles. In this way, a direct correlation between the adsorption strength and structure of the surface active compounds can be achieved. Above all, knowledge of the adsorption mechanism in combination with the structure should facilitate a more rational design into the mainly empirically based production and optimization of nanocomposites.

On producing and sharing knowledge across boundaries: experiences from the interfaces of an international development research network

The number of large research networks and programmes engaging in knowledge production for development has grown over the past years. One of these programmes devoted to generating knowledge about and for development is National Centre of Competence in Research (NCCR) North–South, a cross-disciplinary, international development research network funded by the Swiss Agency for Development and Cooperation and the Swiss National Science Foundation. Producing relevant knowledge for development is a core goal of the programme and an important motivation for many of the participating researchers. Over the years, the researchers have made use of various spaces for exchange and instruments for co-production of knowledge by academic and non-academic development actors. In this article we explore the characteristics of co-producing and sharing knowledge in interfaces between development research, policy and NCCR North–South practice. We draw on empirical material of the NCCR North–South programme and its specific programme element of the Partnership Actions. Our goal is to make use of the concept of the interface to reflect critically about the pursued strategies and instruments applied in producing and sharing knowledge for development across boundaries.

Effect of anode material and cavity design on the performance of microcavity OLEDs

We report on the effect of the replacement of the conventional ITO anode with the semitransparent metallic material on the performance of microcavity OLEDs. We performed comprehensive simulations of the emission from microcavity OLEDs consisting of widely used organic materials, N,N′-di(naphthalene-1- yl)-N,N′-diphenylbenzidine (NPB) as a hole transport layer and tris (8-hydroxyquinoline) (Alq3) as emitting and electron transporting layer. Silver and LiF/Al were considered as a cathode, while metallic (Au and Ag) anode was used and simulations were performed on devices with both the metallic and conventional ITO anode. The electroluminescence emission spectra, electric field distribution inside the device, carrier density, recombination rate and exciton density were calculated as a function of the position of the emission layer. The results show that the metallic anode enhances light output and that optimum emission from a microcavity OLED is achieved when the position of the recombination region is aligned with the antinode of the standing wave inside the cavity. The microcavity OLED devices with Ag/Ag and Ag/Au mirrors were fabricated and characterized. The experimental results have been compared to the simulations and the influence of the different anode, emission region width and position on the performance of microcavity OLEDs was discussed.

INTERFACES ENTRE TECNOLOGIAS EDUCACIONAIS E GESTÃO DE INSTITUIÇÃO DE ENSINO SUPERIOR PRIVADA

O uso de recursos tecnológicos como facilitadores do processo ensino-aprendizado em todos os níveis de ensino tem sido objeto de polêmica entre os pesquisadores do tema. Por um lado aqueles responsáveis pelo ensino os professores resistem às mudanças que a cada dia ocorrem no mundo moderno; por outro os estudantes solicitam um ambiente de aprendizagem que utilize as tecnologias as quais estão acostumados e dominam. Por fim, os gestores das instituições de ensino, que possuem um grande desafio de proporcionar os recursos no interior das instituições, sem permitir, contudo, que comprometam a saúde financeira da instituição. Não obstante, no Brasil a concorrência entre as instituições de ensino tem sido acirrada, principalmente nas instituições de ensino superior privadas. Assim, as instituições procuram um diferencial para atrair seus clientes, objetivando manter a sua sustentabilidade financeira. Esta pesquisa se dispõe a aproximar os temas de gestão do ensino superior com a implantação do uso da tecnologia representada pelo equipamento tablet, demonstrando os resultados para a gestão da instituição de ensino superior antes e depois de sua implantação. A metodologia do estudo de caso - na instituição onde foi analisada mostrou que a implantação da tecnologia proporcionou vantagens competitivas para a gestão - por meio da análise dos indicadores financeiros e a evolução da base de alunos. A tecnologia por si só não prova as vantagens desejadas, porém, com um projeto correlacionado ao modelo de ensino utilizado e material didático que contemple o uso da tecnologia, os custos logísticos foram reduzidos e aumentou a atração de novos alunos, promovendo as vantagens competitivas da Instituição de Ensino.

Novel cationic polymers for use at biological interfaces

One of the main problems with the use of synthetic polymers as biomaterials is the invasion of micro-organisms causing infection. A study of the properties of polymeric antibacterial agents, in particular polyhexamethylene biguanide, has revealed that the essential components for the design of a novel polymeric antibacterial are a balance between hydrophilicity and hydrophobicity coupled with sites of cationicity. The effect of cation incorporation on the physical properties of hydrogels has been investigated. Hydrogel systems copolymerised with either N-vinyl imidazole or dimethylaminoethyl methacrylate have been characterised in terms of their water binding, mechanical and surface properties. It has been concluded that the incorporation of these monomers does not adversely affect the properties of such hydrogels and that these materials are potential candidates for further development for use in biomedical applications. It has been reported that hydro gels with ionic character may increase the deposition of biological material onto the hydrogel surface when it is in contact with body fluids. An investigation into the deposition characteristics of hydrogels containing the potentially cationic monomers has been carried out, using specific protein adsorption and in vitro spoilation techniques. The results suggest that at low levels of cationicity, the deposition of positively charged proteins is reduced without adversely affecting the uptake of the other proteins. The gross deposition characteristics were found to be comparable to some commercially available contact lens materials. A preliminary investigation into the development of novel antibacterial polymers has been completed and some novel methods of bacterial inhibition discussed. These methods include development of an hydrogel whose potential application is as a catheter coating.