Inter-cycle variability of in-cylinder pressure parameters in an ethanol fumigated common rail diesel engine

The effects of ethanol fumigation on the inter-cycle variability of key in-cylinder pressure parameters in a modern common rail diesel engine have been investigated. Specifically, maximum rate of pressure rise, peak pressure, peak pressure timing and ignition delay were investigated. A new methodology for investigating the start of combustion was also proposed and demonstrated—which is particularly useful with noisy in-cylinder pressure data as it can have a significant effect on the calculation of an accurate net rate of heat release indicator diagram. Inter-cycle variability has been traditionally investigated using the coefficient of variation. However, deeper insight into engine operation is given by presenting the results as kernel density estimates; hence, allowing investigation of otherwise unnoticed phenomena, including: multi-modal and skewed behaviour. This study has found that operation of a common rail diesel engine with high ethanol substitutions (>20% at full load, >30% at three quarter load) results in a significant reduction in ignition delay. Further, this study also concluded that if the engine is operated with absolute air to fuel ratios (mole basis) less than 80, the inter-cycle variability is substantially increased compared to normal operation.

The influence of fatty acid methyl ester profiles on inter-cycle variability in a heavy duty compression ignition engine

With the advent of alternative fuels, such as biodiesels and related blends, it is important to develop an understanding of their effects on inter-cycle variability which, in turn, influences engine performance as well as its emission. Using four methanol trans-esterified biomass fuels of differing carbon chain length and degree of unsaturation, this paper provides insight into the effect that alternative fuels have on inter-cycle variability. The experiments were conducted with a heavy-duty Cummins, turbo-charged, common-rail compression ignition engine. Combustion performance is reported in terms of the following key in-cylinder parameters: indicated mean effective pressure (IMEP), net heat release rate (NHRR), standard deviation of variability (StDev), coefficient of variation (CoV), peak pressure, peak pressure timing and maximum rate of pressure rise. A link is also established between the cyclic variability and oxygen ratio, which is a good indicator of stoichiometry. The results show that the fatty acid structures did not have a significant effect on injection timing, injection duration, injection pressure, StDev of IMEP, or the timing of peak motoring and combustion pressures. However, a significant effect was noted on the premixed and diffusion combustion proportions, combustion peak pressure and maximum rate of pressure rise. Additionally, the boost pressure, IMEP and combustion peak pressure were found to be directly correlated to the oxygen ratio. The emission of particles positively correlates with oxygen content in the fuel as well as in the air-fuel mixture resulting in a higher total number of particles per unit of mass.

Spectral analysis of pair-correlation bandwidth: Application to cell biology images

Images from cell biology experiments often indicate the presence of cell clustering, which can provide insight into the mechanisms driving the collective cell behaviour. Pair-correlation functions provide quantitative information about the presence, or absence, of clustering in a spatial distribution of cells. This is because the pair-correlation function describes the ratio of the abundance of pairs of cells, separated by a particular distance, relative to a randomly distributed reference population. Pair-correlation functions are often presented as a kernel density estimate where the frequency of pairs of objects are grouped using a particular bandwidth (or bin width), Δ>0. The choice of bandwidth has a dramatic impact: choosing Δ too large produces a pair-correlation function that contains insufficient information, whereas choosing Δ too small produces a pair-correlation signal dominated by fluctuations. Presently, there is little guidance available regarding how to make an objective choice of Δ. We present a new technique to choose Δ by analysing the power spectrum of the discrete Fourier transform of the pair-correlation function. Using synthetic simulation data, we confirm that our approach allows us to objectively choose Δ such that the appropriately binned pair-correlation function captures known features in uniform and clustered synthetic images. We also apply our technique to images from two different cell biology assays. The first assay corresponds to an approximately uniform distribution of cells, while the second assay involves a time series of images of a cell population which forms aggregates over time. The appropriately binned pair-correlation function allows us to make quantitative inferences about the average aggregate size, as well as quantifying how the average aggregate size changes with time.

Beyond Gauss: Image-set matching on the Riemannian manifold of PDFs

State-of-the-art image-set matching techniques typically implicitly model each image-set with a Gaussian distribution. Here, we propose to go beyond these representations and model image-sets as probability distribution functions (PDFs) using kernel density estimators. To compare and match image-sets, we exploit Csiszar´ f-divergences, which bear strong connections to the geodesic distance defined on the space of PDFs, i.e., the statistical manifold. Furthermore, we introduce valid positive definite kernels on the statistical manifold, which let us make use of more powerful classification schemes to match image-sets. Finally, we introduce a supervised dimensionality reduction technique that learns a latent space where f-divergences reflect the class labels of the data. Our experiments on diverse problems, such as video-based face recognition and dynamic texture classification, evidence the benefits of our approach over the state-of-the-art image-set matching methods.

First simultaneous measurement of the top quark mass in the lepton+jets and dilepton channels at CDF

We present a measurement of the mass of the top quark using data corresponding to an integrated luminosity of 1.9fb^-1 of ppbar collisions collected at sqrt{s}=1.96 TeV with the CDF II detector at Fermilab's Tevatron. This is the first measurement of the top quark mass using top-antitop pair candidate events in the lepton + jets and dilepton decay channels simultaneously. We reconstruct two observables in each channel and use a non-parametric kernel density estimation technique to derive two-dimensional probability density functions from simulated signal and background samples. The observables are the top quark mass and the invariant mass of two jets from the W decay in the lepton + jets channel, and the top quark mass and the scalar sum of transverse energy of the event in the dilepton channel. We perform a simultaneous fit for the top quark mass and the jet energy scale, which is constrained in situ by the hadronic W boson mass. Using 332 lepton + jets candidate events and 144 dilepton candidate events, we measure the top quark mass to be mtop=171.9 +/- 1.7 (stat. + JES) +/- 1.1 (syst.) GeV/c^2 = 171.9 +/- 2.0 GeV/c^2.

Análise espaço-temporal do uso do habitat pelo boto-cinza (Sotalia Guianensis) na Baía de Guanabara, Rio de Janeiro

Determinar áreas de vida tem sido um tema amplamente discutido em trabalhos que procuram entender a relação da espécie estudada com as características de seu habitat. A Baía de Guanabara abriga uma população residente de botos-cinza (Sotalia guianensis) e o objetivo do presente estudo foi analisar o uso espacial de Sotalia guianensis, na Baía de Guanabara (RJ), entre 2002 e 2012. Um total de 204 dias de coleta foi analisado e 902 pontos selecionados para serem gerados os mapas de distribuição. A baía foi dividida em quatro subáreas e a diferença no esforço entre cada uma não ultrapassou 16%. O método Kernel Density foi utilizado nas análises para estimativa e interpretação do uso do habitat pelos grupos de botos-cinza. A interpretação das áreas de concentração da população também foi feita a partir de células (grids) de 1,5km x 1,5km com posterior aplicação do índice de sobreposição de nicho de Pianka. As profundidades utilizadas por S. guianensis não apresentaram variações significativas ao longo do período de estudo (p = 0,531). As áreas utilizadas durante o período de 2002/2004 foram estimadas em 79,4 km com áreas de concentração de 19,4 km. Os períodos de 2008/2010 e 2010/2012 apresentaram áreas de uso estimadas em um total de 51,4 e 58,9 km, respectivamente e áreas de concentração com 10,8 e 10,4 km, respectivamente. As áreas utilizadas envolveram regiões que se estendem por todo o canal central e região nordeste da Baía de Guanabara, onde também está localizada a Área de Proteção Ambiental de Guapimirim. Apesar disso, a área de vida da população, assim como suas áreas de concentração, diminuiu gradativamente ao longo dos anos, especialmente no entorno da Ilha de Paquetá e centro-sul do canal central. Grupos com mais de 10 indivíduos e grupos na classe ≥ 25% de filhotes em sua composição, evidenciaram reduções de mais de 60% no tamanho das áreas utilizadas. A população de botos-cinza vem decrescendo rapidamente nos últimos anos, além de interagir diariamente com fontes perturbadoras, sendo estas possíveis causas da redução do uso do habitat da Baía de Guanabara. Por esse motivo, os resultados apresentados são de fundamental importância para a conservação desta população já que representam consequências da interação em longo prazo com um ambiente costeiro altamente impactado pela ação antrópica.

On classical and other methods of discriminant analysis and estimation of log-odds

For two multinormal populations with equal covariance matrices the likelihood ratio discriminant function, an alternative allocation rule to the sample linear discriminant function when n1 ≠ n2 ,is studied analytically. With the assumption of a known covariance matrix its distribution is derived and the expectation of its actual and apparent error rates evaluated and compared with those of the sample linear discriminant function. This comparison indicates that the likelihood ratio allocation rule is robust to unequal sample sizes. The quadratic discriminant function is studied, its distribution reviewed and evaluation of its probabilities of misclassification discussed. For known covariance matrices the distribution of the sample quadratic discriminant function is derived. When the known covariance matrices are proportional exact expressions for the expectation of its actual and apparent error rates are obtained and evaluated. The effectiveness of the sample linear discriminant function for this case is also considered. Estimation of true log-odds for two multinormal populations with equal or unequal covariance matrices is studied. The estimative, Bayesian predictive and a kernel method are compared by evaluating their biases and mean square errors. Some algebraic expressions for these quantities are derived. With equal covariance matrices the predictive method is preferable. Where it derives this superiority is investigated by considering its performance for various levels of fixed true log-odds. It is also shown that the predictive method is sensitive to n1 ≠ n2. For unequal but proportional covariance matrices the unbiased estimative method is preferred. Product Normal kernel density estimates are used to give a kernel estimator of true log-odds. The effect of correlation in the variables with product kernels is considered. With equal covariance matrices the kernel and parametric estimators are compared by simulation. For moderately correlated variables and large dimension sizes the product kernel method is a good estimator of true log-odds.

The Geography of Conflict and Death in Belfast, Northern Ireland

The conflict known as the oTroubleso in Northern Ireland began during the late 1960s and is defined by political and ethno-sectarian violence between state, pro-state, and anti-state forces. Reasons for the conflict are contested and complicated by social, religious, political, and cultural disputes, with much of the debate concerning the victims of violence hardened by competing propaganda-conditioning perspectives. This article introduces a database holding information on the location of individual fatalities connected with the contemporary Irish conflict. For each victim, it includes a demographic profile, home address, manner of death, and the organization responsible. Employing geographic information system (GIS) techniques, the database is used to measure, map, and analyze the spatial distribution of conflict-related deaths between 1966 and 2007 across Belfast, the capital city of Northern Ireland, with respect to levels of segregation, social and economic deprivation, and interfacing. The GIS analysis includes a kernel density estimator designed to generate smooth intensity surfaces of the conflict-related deaths by both incident and home locations. Neighborhoods with high-intensity surfaces of deaths were those with the highest levels of segregation ( 90 percent Catholic or Protestant) and deprivation, and they were located near physical barriers, the so-called peacelines, between predominantly Catholic and predominantly Protestant communities. Finally, despite the onset of peace and the formation of a power-sharing and devolved administration (the Northern Ireland Assembly), disagreements remain over the responsibility and ocommemorationo of victims, sentiments that still uphold division and atavistic attitudes between spatially divided Catholic and Protestant populations.

Exact Nonparametric Two-Sample Homogeneity Tests for Possibly Discrete Distributions.

In this paper, we study several tests for the equality of two unknown distributions. Two are based on empirical distribution functions, three others on nonparametric probability density estimates, and the last ones on differences between sample moments. We suggest controlling the size of such tests (under nonparametric assumptions) by using permutational versions of the tests jointly with the method of Monte Carlo tests properly adjusted to deal with discrete distributions. We also propose a combined test procedure, whose level is again perfectly controlled through the Monte Carlo test technique and has better power properties than the individual tests that are combined. Finally, in a simulation experiment, we show that the technique suggested provides perfect control of test size and that the new tests proposed can yield sizeable power improvements.

Grain size analyses in tin-lead glazes based on 2d-sections

A problem in the archaeometric classification of Catalan Renaissance pottery is the fact, that the clay supply of the pottery workshops was centrally organized by guilds, and therefore usually all potters of a single production centre produced chemically similar ceramics. However, analysing the glazes of the ware usually a large number of inclusions in the glaze is found, which reveal technological differences between single workshops. These inclusions have been used by the potters in order to opacify the transparent glaze and to achieve a white background for further decoration. In order to distinguish different technological preparation procedures of the single workshops, at a Scanning Electron Microscope the chemical composition of those inclusions as well as their size in the two-dimensional cut is recorded. Based on the latter, a frequency distribution of the apparent diameters is estimated for each sample and type of inclusion. Following an approach by S.D. Wicksell (1925), it is principally possible to transform the distributions of the apparent 2D-diameters back to those of the true three-dimensional bodies. The applicability of this approach and its practical problems are examined using different ways of kernel density estimation and Monte-Carlo tests of the methodology. Finally, it is tested in how far the obtained frequency distributions can be used to classify the pottery

Active regions for colour texture segmentation integrating region and boundary information

In this paper a colour texture segmentation method, which unifies region and boundary information, is proposed. The algorithm uses a coarse detection of the perceptual (colour and texture) edges of the image to adequately place and initialise a set of active regions. Colour texture of regions is modelled by the conjunction of non-parametric techniques of kernel density estimation (which allow to estimate the colour behaviour) and classical co-occurrence matrix based texture features. Therefore, region information is defined and accurate boundary information can be extracted to guide the segmentation process. Regions concurrently compete for the image pixels in order to segment the whole image taking both information sources into account. Furthermore, experimental results are shown which prove the performance of the proposed method

A process for analysis of microarray comparative genomics hybridisation studies for bacterial genomes

Background: Microarray based comparative genomic hybridisation (CGH) experiments have been used to study numerous biological problems including understanding genome plasticity in pathogenic bacteria. Typically such experiments produce large data sets that are difficult for biologists to handle. Although there are some programmes available for interpretation of bacterial transcriptomics data and CGH microarray data for looking at genetic stability in oncogenes, there are none specifically to understand the mosaic nature of bacterial genomes. Consequently a bottle neck still persists in accurate processing and mathematical analysis of these data. To address this shortfall we have produced a simple and robust CGH microarray data analysis process that may be automated in the future to understand bacterial genomic diversity. Results: The process involves five steps: cleaning, normalisation, estimating gene presence and absence or divergence, validation, and analysis of data from test against three reference strains simultaneously. Each stage of the process is described and we have compared a number of methods available for characterising bacterial genomic diversity, for calculating the cut-off between gene presence and absence or divergence, and shown that a simple dynamic approach using a kernel density estimator performed better than both established, as well as a more sophisticated mixture modelling technique. We have also shown that current methods commonly used for CGH microarray analysis in tumour and cancer cell lines are not appropriate for analysing our data. Conclusion: After carrying out the analysis and validation for three sequenced Escherichia coli strains, CGH microarray data from 19 E. coli O157 pathogenic test strains were used to demonstrate the benefits of applying this simple and robust process to CGH microarray studies using bacterial genomes.

A Gaussian-mixture ensemble transform filter

We generalize the popular ensemble Kalman filter to an ensemble transform filter, in which the prior distribution can take the form of a Gaussian mixture or a Gaussian kernel density estimator. The design of the filter is based on a continuous formulation of the Bayesian filter analysis step. We call the new filter algorithm the ensemble Gaussian-mixture filter (EGMF). The EGMF is implemented for three simple test problems (Brownian dynamics in one dimension, Langevin dynamics in two dimensions and the three-dimensional Lorenz-63 model). It is demonstrated that the EGMF is capable of tracking systems with non-Gaussian uni- and multimodal ensemble distributions. Copyright © 2011 Royal Meteorological Society

Properties of series feature aggregation schemes

Feature aggregation is a critical technique in content-based image retrieval (CBIR) that combines multiple feature distances to obtain image dissimilarity. Conventional parallel feature aggregation (PFA) schemes failed to effectively filter out the irrelevant images using individual visual features before ranking images in collection. Series feature aggregation (SFA) is a new scheme that aims to address this problem. This paper investigates three important properties of SFA that are significant for design of systems. They reveal the irrelevance of feature order and the convertibility of SFA and PFA as well as the superior performance of SFA. Furthermore, based on Gaussian kernel density estimator, the authors propose a new method to estimate the visual threshold, which is the key parameter of SFA. Experiments, conducted with IAPR TC-12 benchmark image collection (ImageCLEF2006) that contains over 20,000 photographic images and defined queries, have shown that SFA can outperform conventional PFA schemes.

Properties of series feature aggregation schemes

Feature aggregation is a critical technique in content-based image retrieval (CBIR) that combines multiple feature distances to obtain image dissimilarity. Conventional parallel feature aggregation (PFA) schemes failed to effectively filter out the irrelevant images using individual visual features before ranking images in collection. Series feature aggregation (SFA) is a new scheme that aims to address this problem. This paper investigates three important properties of SFA that are significant for design of systems. They reveal the irrelevance of feature order and the convertibility of SFA and PFA as well as the superior performance of SFA. Furthermore, based on Gaussian kernel density estimator, the authors propose a new method to estimate the visual threshold, which is the key parameter of SFA. Experiments, conducted with IAPR TC-12 benchmark image collection (ImageCLEF2006) that contains over 20,000 photographic images and defined queries, have shown that SFA can outperform conventional PFA schemes.