Effect of sodium alginate concentration on membrane strength and permeating property of poly-l-arginine group microcapsule

A novel poly-l-arginine microcapsule was prepared due to its nutritional function and pharmacological efficacy. A high-voltage electrostatic droplet generator was used to make uniform microcapsules. The results show that the membrane strength and permeating property are both remarkably affected with the changes of sodium alginate concentration. With the sodium alginate concentration increasing, gel beads sizes increase from 233 mum to 350 mum, release ratio is also higher at the same time, but the membrane strength decreases.

Preparation and physical properties of enhanced radiation induced crosslinking of ethylene-vinyl alcohol copolymer (EVOH)

Preparation and physical properties of ethylene-vinyl alcohol copolymer (EVOH) crosslinked by enhanced radiation have been studied through various methods. It was found that the most effective agent for irradiation-crosslinking was triallyl isocyanurate (TAIC) among four kinds of polyfunctional monomers. Gel content (65.6%) was formed for EVOH-44 (content of ethylene is 44 mol%) at 200 kGy with 5% TAIC, but for EVOH-32 (content of ethylene is 32 mol%), only 37.4% gel content was formed under the same conditions. This result showed that the more the content of ethylene units comprised in EVOH, the easier the chemical bonds could be formed between different molecular chains. Tensile strength and elastic modulus increased after crosslinking at high test temperature and elongation at break decreased at the same time. Hygroscopicity of EVOH showed noticeable decrease after enhancement radiation-crosslinking.

Effect of solution pH, ionic strength, and temperature on adsorption behavior of reactive dyes on activated carbon

The adsorption behavior of C.I. Reactive Blue 2, C.I. Reactive Red 4, and C.I. Reactive Yellow 2 from aqueous solution onto activated carbon was investigated under various experimental conditions. The adsorption capacity of activated carbon for reactive dyes was found to be relatively high. At pH 7.0 and 298 K, the maximum adsorption capacity for C.I. Reactive Blue 2, C.I. Reactive Yellow 2 and C.I. Reactive Red 4 dyes was found to be 0.27, 0.24, and 0.11 mmol/g, respectively. The shape of the adsorption isotherms indicated an L2-type isotherm according to the Giles and Smith classification. The experimental adsorption data showed good correlation with the Langmuir and Ferundlich isotherm models. Further analysis indicated that the formation of a complete monolayer was not achieved, with the fraction of surface coverage found to be 0.45, 0.42, and 0.22 for C.I. Reactive Blue 2, C.I. Reactive Yellow 2 and C.I. Reactive Red 4 dyes, respectively. Experimental data indicated that the adsorption capacity of activated carbon for the dyes was higher in acidic rather than in basic solutions, and further indicated that the removal of dye increased with increase in the ionic strength of solution, this was attributed to aggregation of reactive dyes in solution. Thermodynamic studies indicated that the adsorption of reactive dyes onto activated carbon was an endothermic process. The adsorption enthalpy (?H) for C.I. Reactive Blue 2 and C.I. Reactive Yellow 2 dyes were calculated at 42.2 and 36.2 kJ/mol, respectively. The negative values of free energy (?G) determined for these systems indicated that adsorption of reactive dyes was spontaneous at the temperatures under investigation (298-328 K). © 2007 Elsevier Ltd. All rights reserved.

Predicting impact damage, residual strength and crashworthiness of composite structures

The development of the latest generation of wide-body carbon-fibre composite passenger aircraft has heralded a new era in the utilisation of these materials. The premise of superior specific strength and stiffness, corrosion and fatigue resistance, is tempered by high development costs, slow production rates and lengthy and expensive certification programmes. Substantial effort is currently being directed towards the development of new modelling and simulation tools, at all levels of the development cycle, to mitigate these shortcomings. One of the primary challenges is to reduce the extent of physical testing, in the certification process, by adopting a ‘certification by simulation’ approach. In essence, this aspirational objective requires the ability to reliably predict the evolution and progression of damage in composites. The aerospace industry has been at the forefront of developing advanced composites modelling tools. As the automotive industry transitions towards the increased use of composites in mass-produced vehicles, similar challenges in the modelling of composites will need to be addressed, particularly in the reliable prediction of crashworthiness. While thermoset composites have dominated the aerospace industry, thermoplastics composites are likely to emerge as the preferred solution for meeting the high-volume production demands of passenger road vehicles. This keynote presentation will outline recent progress and current challenges in the development of finite-element-based predictive modelling tools for capturing impact damage, residual strength and energy absorption capacity of thermoset and thermoplastic composites for crashworthiness assessments.

Effects of dietary restraint and oral contraceptives on bone strength and bone turnover in young women

ABSTRACT Introduction The purpose of this study was to assess specific osteoporosis-related health behaviours and physiological outcomes including daily calcium intake, physical activity levels, bone strength, as assessed by quantitative ultrasound, and bone turnover among women between the ages of 18 and 25. Respective differences on relevant study variables, based on dietary restraint and oral contraceptive use were also examined. Methods One hundred women (20.6 ± 0.2 years of age) volunteered to participate in the study. Informed written consent was obtained by all subjects prior to participation. The study and all related procedures were approved by the Brock University Research Ethics Board. Body mass, height, relative body fat, as well as chest, waist and hip circumferences were measured using standard procedures. The 10-item restrained eating subscale of the Dutch Eating Behaviour Questionnaire (DEBQ) was used to assess dietary restraint (van Strien et al., 1986). Daily calcium intake was assessed by the Rapid Assessment Method (RAM) (Hertzler & Frary 1994). Weekly physical activity was documented by the 4-item Godin Leisure-Time Exercise Questionnaire (Godin & Shephard 1985). Bone strength was determined from the speed of sound (SOS) as measured by QUS (Sunlight 7000S). SOS measurements (m/s) were taken of the dominant and non-dominant sides of the distal one third of the radius and the mid-shaft of the tibia. Resting blood samples were collected from all subjects between 9am and 12pm, in order to evaluate the impact of lifestyle factors on biochemical markers of bone turnover. Blood was collected during the early follicular phase of the menstrual cycle (approximately days 1-5) for all subjects. Samples were centrifliged and the serum or plasma was aliquoted into separate tubes and stored at -80°C until analysis. The bone formation markers measured were Osteocalcin (OC), bone specific alkaline phosphatase (BAP) and 25-OH vitamin D. The bone resorption markers measured were the carboxy (CTx) and amino (NTx) terminal telopeptides of type-I collagen crosslinks. All markers were assessed by ELISA. Subjects were divided into high (HDR) and low dietary restrainers (LDR) based on the median DEBQ score, and also into users (BC) and non-users (nBC) of oral contraceptives. A series of multiple one way ANOVA's were then conducted to identify differences between each set of groups for all relevant variables. A two-way ANOVA analysis was used to explore significant interactions between dietary restraint and use of oral contraceptives while a univariate follow-up analysis was also performed when appropriate. Pearson Product Moment Correlations were used to determine relationships among study variables. Results HDR had significantly higher BMI, %BF and circumference measures but lower daily calcium intake than LDR. There were no significant differences in physical activity levels between HDR and LDR. No significant differences were found between BC and nBC in body composition, calcium intake and physical activity. HDR had significantly lower tibial SOS scores than LDR in both the dominant and non-dominant sites. The post-hoc analysis showed that within the non-birth control group, the HDR had significantly lower tibial SOS scores of bone strength when compared to the LDR but Aere were no significant differences found between the two dietary restraint groups for those currently on birth control. HDR had significantly lower levels of OC than LDR and the BC group had lower levels of BAP than the nBC group. Consistently, the follow-up analysis revealed that within those not on birth control, subjects who were classified as HDR had significantly (f*<0.05) lower levels of OC when compared with LDR but no significant differences were observed in bone turnover between the two dietary restraint groups for those currently on birth control. Physical activity was not correlated with SOS scores and bone turnover markers possibly due to the low physical activity variability in this group of women. Conclusion This is the first study to examine the effects of dietary restraint on bone strength and turnover among this population of women. The most important finding of this study was that bone strength and turnover are negatively influenced by dietary restraint independent of relative body fat. In general, the results of the present thesis suggest that dietary restraint, oral contraceptive use, as well as low daily calcium intake and low physical activity levels were widespread behaviours among this population of college-aged women. The young women who were using dietary restraint as a strategy to lose weight, and thus were in the HDR group, despite their higher relative body fat and weight, had lower scores of bone strength and lower levels of markers of bone turnover compared to the low dietary restrainers. Additionally, bone turnover seemed to be negatively affected by oral contraceptives, while bone strength, as assessed by QUS, seemed unaffected by their use in this population of young women. Physical activity (weekly energy expenditure), on the other hand, was not associated with either bone strength or bone tiimover possibly due to the low variability of this variable in this population of young Canadian women.

A Study Of The Strength And Compressibility Characteristics Of Cochin Marine Clays

With the advent of urbanisation and consequent search for more and more habitable land, it was imperative that the large tracts of marine clays, considered inhabitable earlier, had to be reclaimed and developed. These marine clays, wellknown for its high compressibility and poor shear strength, posed numerous problems to the builders and Cochin was no exception. It is only less than a decade since active research work was initiated on marine clays in general and Cochin marine clays in particular. Eventhough some systematic studies are available on compressibility characteristics, attempts to study the shear strength aspects and development of techniques to improve it have been very limited. This work is an investigation on the consolidation and shear strength characteristics of Cochin marine clays including methods to improve the same

The significance of volcanic eruption strength and frequency for climate

A simple physical model of the atmospheric effects of large explosive volcanic eruptions is developed. Using only one input parameter - the initial amount of sulphur dioxide injected into the stratosphere - the global-average stratospheric optical-depth perturbation and surface temperature response are modelled. The simplicity of this model avoids issues of incomplete data (applicable to more comprehensive models), making it a powerful and useful tool for atmospheric diagnostics of this climate forcing mechanism. It may also provide a computationally inexpensive and accurate way of introducing volcanic activity into larger climate models. The modelled surface temperature response for an initial sulphur-dioxide injection, coupled with emission-history statistics, is used to demonstrate that the most climatically significant volcanic eruptions are those of sufficient explosivity to just reach into the stratosphere (and achieve longevity). This study also highlights the fact that this measure of significance is highly sensitive to the representation of the climatic response and the frequency data used, and that we are far from producing a definitive history of explosive volcanism for at least the past 1000 years. Given this high degree of uncertainty, these results suggest that eruptions that release around and above 0.1 Mt SO2 into the stratosphere have the maximum climatic impact.

Estimation of in vitro prebiotic activity of individual and mixed dietary fibres

Background: Epidemiological studies have demonstrated a link between dietary fibre deficiency and prevalence of many “Western diseases” particularly colon related diseases. Many of the health benefits associated with dietary fibre are attributed to their prebiotic effect. However, not all fibres have the same prebiotic potential or the same impact on colon health.

Objective: To examine the in vitro fermentation properties of individual and mixed dietary fibres by measuring fermentation byproducts over time.

Design: Wheat bran and guar gum were selected for this study. Individual and mixed dietary fibres were added to batch fermentation system and were inoculated with fresh faecal inoculum (n= 4). Positive (inulin) and negative (no substrate) fermenters were also used to determine the differences. The pH of the five fermenters was adjusted to a baseline of 5.5 and 6.8 representing the pH of the proximal and distal sections of the colon respectively. Samples were drawn out of the fermenters at 0, 3, 9 and 24 hours for the analysis of pH, ammonia and short chain fatty acids (SCFAs).

Outcomes: There were no significant differences in the pH levels at various time points between fermenters adjusted to pH 5.5 at baseline. However, in fermenters adjusted to pH 6.8 the pH of the fermenter containing wheat bran increased over the time (24h (P = 0.017)) due to production of a high amount of ammonia. The total SCFAs production was greater in fermenters containing combined fibres.

Conclusion: There is a large inter-individual variation in the prebiotic effect of all types of dietary fibres, however, in the present study, dietary fibre combinations showed greater prebiotic potential compared with the individual fibres.

Simultaneously enhanced strength and ductility of titanium via multimodal grain structure

Commercial Ti with a multimodal grain structure was successfully produced using cryorolling, followed by low-temperature annealing. This multimodal grain structure Ti exhibited a combination of high yield strength (926 MPa), a uniform elongation of 11% and a failure elongation of 23%. The strength enhancement was mainly derived from the ultrafine equiaxed grains, while the improved ductility originated from the large fraction of high-angle grain boundaries and the multimodal grain structure.

Reliability of isokinetic strength and aerobic power testing for patients with chronic heart failure

PURPOSE: The objective of this study was to assess the reliability of testing skeletal muscle strength and peak aerobic power in a clinical population of patients with chronic heart failure (CHF).

METHODS: Thirty-three patients with CHF (New York Heart Association (NYHA) Functional Class 2.3 ± 0.5; left ventricular ejection fraction 27% ± 7%; age 65 ± 9 years; 28:5 male-female ratio) underwent two identical series of tests (T1 and T2), 1 week apart, for strength and endurance of the muscle groups responsible for knee extension/flexion and elbow extension/flexion. The patients also underwent two graded exercise tests on a bicycle ergometer to measure peak oxygen consumption (VO_2peak). Three months later, 18 of the patients underwent a third test (T3) for each of the measures. Means were compared using MANOVA with repeated measures for strength and endurance, and ANOVA with repeated measures for VO_2peak.

RESULTS: Combining data for all four movement patterns, the expression of strength increased from T1 to T2 by 12% ± 25% (P < .001; intraclass correlation coefficient [ICC] = 0.89). Correspondingly, endurance increased by 13% ± 23% (P = .004; ICC = 0.87). Peak oxygen consumption was not significantly different (16.2 ± 0.8 and 16.1 ± 0.8 mL·kg^-1·min^-1 for T1 and T2, respectively;P = .686; ICC = 0.91). There were no significant differences between T2 and T3 for strength (2% ± 17%;P = .736; ICC = 0.92) or muscle endurance (-1% ± 15%;P = .812; ICC = 0.96), but VO_2peak decreased from 16.7 ± 1.2 to 14.9 ± 0.9 mL·kg^-1·min^-1 (-10% ± 18%;P = .021; ICC = 0.89).

CONCLUSIONS: These data suggest that in a population of patients with CHF, a familiarization trial for skeletal muscle strength testing is necessary. Although familiarization is not required for assessing oxygen consumption as a single measurement, VO_2peak declined markedly in the 3-month period for which these patients were followed. Internal consistency within patients was high for the second and third strength trials and the first and second tests of VO_2peak.

Bone strength and density via pQCT in post-menopausal osteopenic women after 9 months resistive exercise with whole body vibration or proprioceptive exercise

OBJECTIVES: In order to better understand which training approaches are more effective for preventing bone loss in post-menopausal women with low bone mass, we examined the effect of a nine-month resistive exercise program with either an additional whole body vibration exercise (VIB) or balance training (BAL). METHODS: 68 post-menopausal women with osteopenia were recruited for the study and were randomised to either the VIB or BAL group. Two training sessions per week were performed. 57 subjects completed the study (VIB n=26; BAL n=31). Peripheral quantitative computed tomography (pQCT) measurements of the tibia, fibula, radius and ulna were performed at baseline and at the end of the intervention period at the epiphysis (4% site) and diaphysis (66% site). Analysis was done on an intent-to-treat approach. RESULTS: Significant increases in bone density and strength were seen at a number of measurement sites after the intervention period. No significant differences were seen in the response of the two groups at the lower-leg. CONCLUSIONS: This study provided evidence that a twice weekly resistive exercise program with either additional balance or vibration training could increase bone density at the distal tibia after a nine-month intervention period in post-menopausal women with low bone mass.

Mechanical strength and subcritical crack growth under wet cyclic loading of glass-infiltrated dental ceramics

Objectives. Evaluate the flexural strength (sigma) and subcritical crack growth (SCG) under cyclic loading of glass-infiltrated alumina-based (IA, In-Ceram Alumina) and zirconia-reinforced (IZ, In-Ceram Zirconia) ceramics, testing the hypothesis that wet environment influences the SCG of both ceramics when submitted to cyclic loading.Methods. Bar-shaped specimens of IA (n = 45) and IZ ( n = 45) were fabricated and loaded in three-point bending (3P) in 37 degrees C artificial saliva (IA(3P) and IZ(3P)) and cyclic fatigued (F) in dry (D) and wet (W) conditions (IA(FD), IA(FW), IZ(FD), IZ(FW)). The initial sigma and the number of cycles to fracture were obtained from 3P and F tests, respectively. Data was examined using Weibull statistics. The SCG behavior was described in terms of crack velocity as a function of maximum stress intensity factor (K(Imax)).Results. The Weibull moduli (m = 8) were similar for both ceramics. The characteristic strength (sigma(0)) of IA and IZ was and 466 MPa 550 MPa, respectively. The wet environment significantly increased the SCG of IZ, whereas a less evident effect was observed for IA. In general, both ceramics were prone to SCG, with crack propagation occurring at K(I) as low as 43-48% of their critical K(I). The highest sigma of IZ should lead to longer lifetimes for similar loading conditions.Significance. Water combined with cyclic loading causes pronounced SCG in IZ and IA materials. The lifetime of dental restorations based on these ceramics is expected to increase by reducing their direct exposure to wet conditions and/or by using high content zirconia ceramics with higher strength. (C) 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.