Effect of soil preparation of boreal spruce forest on air and soil temperature conditions in forest regeneration areas.

The effect of scarification, ploughing and cross-directional plouhing on temperature conditions in the soil and adjacent air layer have been studied during 11 consecutive growth periods by using an unprepared clear-cut area as a control site. The maximum and minimum temperatures were measured daily in the summer months, and other temperature observations were made at four-hour intervals by means of a Grant measuring instrument. The development of the seedling stand was also followed in order to determine its shading effect on the soil surface. Soil preparation decreased the daily temperature amplitude of the air at the height of 10 cm. The maximum temperatures on sunny days were lower in the tilts of the ploughed and in the humps of the cross-directional ploughed sites compared with the unprepared area. Correspondingly, the night temperatures were higher and so the soil preparation considerably reduced the risk of night frost. In the soil at the depth of 5 cm, soil preparation increased daytime temperatures and reduced night temperatures compared with unprepared area. The maximum increase in monthly mean temperatures was almost 5 °C, and the daily variation in the surface parts of the tilts and humps increased so that excessively high temperatures for the optimal growth of the root system were measured from time to time. The temperature also rose at the depths of 50 and 100 cm. Soil preparation also increased the cumulative temperature sum. The highest sums accumulated during the summer months were recorded at the depth of 5 cm in the humps of cross-directional ploughed area (1127 dd.) and in the tilts of the ploughed area (1106 dd.), while the corresponding figure in the unprepared soil was 718 dd. At the height of 10 cm the highest temperature sum was 1020 dd. in the hump, the corresponding figure in the unprepared area being 925 dd. The incidence of high temperature amplitudes and percentage of high temperatures at the depth of 5 cm decreased most rapidly in the humps of cross-directional ploughed area and in the ploughing tilts towards the end of the measurement period. The decrease was attributed principally to the compressing of tilts, the ground vegetation succession and the growth of seedlings. The mean summer temperature in the unprepared area was lower than in the prepared area and the difference did not diminish during the period studied. The increase in temperature brought about by soil preparation thus lasts at least more than 10 years.

Computational study of the vortex path variation with the VG height

An extensive range of conventional, vane-type, passive vortex generators (VGs) are in use for successful applications of flow separation control. In most cases, the VG height is designed with the same thickness as the local boundary layer at the VG position. However, in some applications, these conventional VGs may produce excess residual drag. The so-called low-profile VGs can reduce the parasitic drag associated to this kind of passive control devices. As suggested by many authors, low-profile VGs can provide enough momentum transfer over a region several times their own height for effective flow-separation control with much lower drag. The main objective of this work is to study the variation of the path and the development of the primary vortex generated by a rectangular VG mounted on a flat plate with five different device heights h = delta, h(1) = 0.8 delta, h(2) = 0.6 delta, h(3) = 0.4 delta and h(4) = 0.2 delta, where delta is the local boundary layer thickness. For this purpose, computational simulations have been carried out at Reynolds number Re = 1350 based on the height of the conventional VG h = 0.25m with the angle of attack of the vane to the oncoming flow beta = 18.5 degrees. The results show that the VG scaling significantly affects the vortex trajectory and the peak vorticity generated by the primary vortex.

Tip leakage flow and heat transfer on turbine blade tip and casing, Part 1: Effect of tip clearance height and rotation speed

Steady simulations were performed to investigate tip leakage flow and heat transfer characteristics on the rotor blade tip and casing in a single-stage gas turbine engine. A typical high-pressure gas turbine stage was modeled with a pressure ratio of 3.2. The predicted isentropic Mach number and adiabatic wall temperature on the casing showed good agreement with available experimental data under similar operating condition. The present numerical study focuses extensively on the effects of tip clearance heights and rotor rotational speeds on the blade tip and casing heat transfer characteristics. It was observed that the tip leakage flow structure is highly dependent on the height of the tip gap and the speed of the rotor. In all cases, the tip leakage flow was seen to separate and recirculate just around the corner of the pressure side of the blade tip. This region of re-circulating flow enlarges with increasing clearance heights. The separated leakage flow reattaches afterwards on the tip surface. Leakage flow reattachment was shown to enhance surface heat transfer at the tip. The interaction between tip leakage flow and secondary flows that is induced by the relative casing motion is found to significantly influence the blade tip and casing heat transfer distribution. A region of critical heat transfer exists on the casing near the blade tip leading edge and along the pressure-side edge for all the clearance heights that were investigated. At high rotation speed, the region of critical heat transfer tends to move towards the trailing edge due to the change in inflow angle.

Independent evaluation of the ability of spaceborne radar and lidar to retrieve the microphysical and radiative properties of ice clouds

The combination of radar and lidar in space offers the unique potential to retrieve vertical profiles of ice water content and particle size globally, and two algorithms developed recently claim to have overcome the principal difficulty with this approach-that of correcting the lidar signal for extinction. In this paper "blind tests" of these algorithms are carried out, using realistic 94-GHz radar and 355-nm lidar backscatter profiles simulated from aircraft-measured size spectra, and including the effects of molecular scattering, multiple scattering, and instrument noise. Radiation calculations are performed on the true and retrieved microphysical profiles to estimate the accuracy with which radiative flux profiles could be inferred remotely. It is found that the visible extinction profile can be retrieved independent of assumptions on the nature of the size distribution, the habit of the particles, the mean extinction-to-backscatter ratio, or errors in instrument calibration. Local errors in retrieved extinction can occur in proportion to local fluctuations in the extinction-to-backscatter ratio, but down to 400 m above the height of the lowest lidar return, optical depth is typically retrieved to better than 0.2. Retrieval uncertainties are greater at the far end of the profile, and errors in total optical depth can exceed 1, which changes the shortwave radiative effect of the cloud by around 20%. Longwave fluxes are much less sensitive to errors in total optical depth, and may generally be calculated to better than 2 W m(-2) throughout the profile. It is important for retrieval algorithms to account for the effects of lidar multiple scattering, because if this is neglected, then optical depth is underestimated by approximately 35%, resulting in cloud radiative effects being underestimated by around 30% in the shortwave and 15% in the longwave. Unlike the extinction coefficient, the inferred ice water content and particle size can vary by 30%, depending on the assumed mass-size relationship (a problem common to all remote retrieval algorithms). However, radiative fluxes are almost completely determined by the extinction profile, and if this is correct, then errors in these other parameters have only a small effect in the shortwave (around 6%, compared to that of clear sky) and a negligible effect in the longwave.

The role of flower inclination, depth, and height in the preferences of a pollinating beetle (Coleoptera : Glaphyridae)

Amphicoma ( Glaphyridae) beetles are important pollinators of red bowl-shaped flowers in the Mediterranean. The role of color and shape in flower choice is well studied but the roles of inclination, depth, and height have seldom been investigated. Under field conditions, models were used to experimentally manipulate these three characters and visitation rates of beetles were recorded. Models with red horizontal surfaces were visited significantly more often than models with red vertical surfaces. Shallow flower models were visited significantly more than deeper equivalents. Models below or at the height of natural flower populations elicited significantly more landings than models above the height of flowers. Inclination, depth, and height characteristics are all likely to be important components in the flower preferences exhibited by pollinating beetles.

Epic Sea Battle at Night: a Revolutionary Play with the Economic Thinking of Milton Friedman

The play Epic Sea Battle at Night was originally staged in 1967, to commemorate two of China’s People’s Liberation Army’s military triumphs over the Taiwanese navy two years previously. Produced at the height of the Chinese Cultural Revolution, the play is an example of the exploitation of the arts as an ideological instrument, celebrating military heroism and political conviction. Stills from the play were included in, China Pictorial 11, an English language propaganda pamphlet that was distributed to Western Imperialists in order to educate them in Maoist policy. Today, these images are clear representations of ideology. More than forty years after the Cultural Revolution, the ideology under which we live, neo-liberal late-capitalism, deliberately shirks from such blatant displays of propaganda. We have supposedly the freedom to believe whatever we like in a post-ideological age, and yet core beliefs about meritocracy, individualism and competitiveness frequently go unchallenged. By juxtaposing the visual language of ideology with the text of the capitalist manifesto, the re-enactment of a scene from Epic Sea Battle at Night harnesses the aesthetics of the past so as to allow us to reconsider the alleged neutrality of the present. The design of the stage, the positioning of the actors, costumes and props of the current production closely resembled those documented in China Pictorial 11, yet the actors’ monologues belong to a completely different context. No less heroic and utopian in tone than the speech given by the political instructor of gunboat 874 in the original play, the capitalist manifesto was an attempt to give a concrete language to the shapeless ideology of the present, and to force the invisible currents that govern life today, in China as in the West, to the surface. Neither a lecture on neo-liberal economics, nor a theatrical performance of a narrative, the piece appropriated the format of the propaganda play to re-evaluate the relationship between art and politics now.

Vertical growth of mini watermelon according to the training height and plant density

A melancia é uma espécie tradicionalmente conduzida em campo no sistema rasteiro. As cultivares de frutos pequenos (1 a 3 kg), que adquirem melhores preços de mercado, vêm sendo cultivadas também em ambiente protegido, onde são conduzidas no sistema vertical, com poda de ramos e raleio de frutos. Essas práticas possibilitam aumentar o adensamento das plantas, a qualidade e a produtividade de frutos em comparação ao sistema rasteiro. Objetivou-se com este trabalho avaliar a influência de três alturas de condução (1,7; 2,2 e 2,7 m) e duas densidades de plantas (3,17 e 4,76 plantas m-2) sobre as características produtivas e qualitativas da mini melancia Smile cultivada em ambiente protegido. A poda da haste principal foi realizada aos 43, 55 e 66 dias após o transplante (DAT) para as alturas de condução de 1,7; 2,2 e 2,7 m, respectivamente. A massa seca dos ramos, dos pecíolos, das folhas e total foram afetados pela altura de condução, cujos maiores valores foram obtidos para as plantas conduzidas a 2,2 e 2,7 m de altura. A área foliar, a área foliar específica e o índice de área foliar não foram influenciados pela altura de condução das plantas. A altura de condução de 2,7 m elevou a produtividade total. Entretanto, a produtividade comercial, a massa média dos frutos e todas as características qualitativas não foram significativamente diferentes das obtidos pela altura de poda de 2,2 m. em relação à densidade de plantas, a melhor opção foi a de 4,76 plantas m-2, pois elevou a produtividade comercial em 37,4% sem reduzir a massa média dos frutos.

Vertical growth of mini watermelon according to the training height and plant density

The watermelon is traditionally cultivated horizontally on the ground. The cultivars of small fruits (1 to 3 kg), which reach better market prices, are also being grown in a greenhouse, where the plants are trained upward on vertical supports, with branches pruning and fruits thinning. These practices make possible an increase of the plant density, fruit quality and yield compared to the traditional growth system. The aim of this experiment was to evaluate the influence of three training heights (1.7, 2.2 and 2.7 m) and two planting densities (3.17 and 4.76 plants m-2) over the productive and qualitative characteristics of mini watermelon "Smile" cultivated in greenhouse. The pruning was done at 43, 55 and 66 days after transplanting (DAT), when the plant height reached 1.7, 2.2 and 2.7 m, respectively. The dry mass of branches, petioles, leaves and total were affected by the training height, where the highest values were obtained by the plants pruned at 2.2 and 2.7 m. Leaf area, specific leaf area and leaf area index were not affected by the height of the plants. The training height of 2.7 m raised the total yield, however, marketable yield, average fruit mass and all the quality characteristics did not differ significantly from those obtained by the training height of 2.2 m. Regarding to plant density, the best option was 4.76 plants m-2, due to the increasing of marketable yield in 37.4% without reducing the average weight of fruits.

Precision of fit and retention force of cast non-precious-crowns on standard titanium implant-abutment with different design and height

OBJECTIVE The cost-effectiveness of cast nonprecious frameworks has increased their prevalence in cemented implant crowns. The purpose of this study was to assess the effect of the design and height of the retentive component of a standard titanium implant abutment on the fit, possible horizontal rotation and retention forces of cast nonprecious alloy crowns prior to cementation. MATERIALS AND METHODS Two abutment designs were examined: Type A with a 6° taper and 8 antirotation planes (Straumann Tissue-Level RN) and Type B with a 7.5° taper and 1 antirotation plane (SICace implant). Both types were analyzed using 60 crowns: 20 with a full abutment height (6 mm), 20 with a medium abutment height (4 mm), and 20 with a minimal (2.5 mm) abutment height. The marginal and internal fit and the degree of possible rotation were evaluated by using polyvinylsiloxane impressions under a light microscope (magnification of ×50). To measure the retention force, a custom force-measuring device was employed. STATISTICAL ANALYSIS one-sided Wilcoxon rank-sum tests with Bonferroni-Holm corrections, Fisher's exact tests, and Spearman's rank correlation coefficient. RESULTS Type A exhibited increased marginal gaps (primary end-point: 55 ± 20 μm vs. 138 ± 59 μm, P < 0.001) but less rotation (P < 0.001) than Type B. The internal fit was also better for Type A than for Type B (P < 0.001). The retention force of Type A (2.49 ± 3.2 N) was higher (P = 0.019) than that of Type B (1.27 ± 0.84 N). Reduction in abutment height did not affect the variables observed. CONCLUSION Less-tapered abutments with more antirotation planes provide an increase in the retention force, which confines the horizontal rotation but widens the marginal gaps of the crowns. Thus, casting of nonprecious crowns with Type A abutments may result in clinically unfavorable marginal gaps.

Use of cognitive interviewing in the development of a Spanish language genetic knowledge instrument

Study purpose. Genetic advances are significantly impacting healthcare, yet recent studies of ethnic group participation in genetic services demonstrate low utilization rates by Latinos. Limited genetic knowledge is a major barrier. The purpose of this study was to field test items in a Spanish-language instrument that will be used to measure genetic knowledge relevant to type 2 diabetes among members of the ethnically heterogeneous U.S. Latino community. Accurate genetic knowledge measurement can provide the foundation for interventions to enhance genetic service utilization. ^ Design. Three waves of cognitive interviews were conducted in Spanish to field test 44 instrument items Thirty-six Latinos, with 12 persons representative of Mexican, Central and South American, and Cuban heritage participated, including 7 males and 29 females between 22 and 60 years of age; 17 participants had 12 years or less of education. ^ Methods. Text narratives from transcriptions of audiotaped interviews were qualitatively analyzed using a coding strategy to indicate potential sources of response error. Through an iterative process of instrument refinement, codes that emerged from the data were used to guide item revisions at the conclusion of each phase; revised items were examined in subsequent interview waves. ^ Results. Inter-cultural and cross-cultural themes associated with difficulties in interpretation and grammatical structuring of items were identified; difficulties associated with comprehension reflected variations in educational level. Of the original 44 items, 32 were retained, 89% of which were revised. Six additional items reflective of cultural knowledge were constructed, resulting in a 38-item instrument. ^ Conclusions. Use of cognitive interviewing provided a valuable tool for detecting both potential sources of response error and cultural variations in these sources. Analysis of interview data guided successive instrument revisions leading to improved item interpretability and comprehension. Although testing in a larger sample will be essential to test validity and reliability, the outcome of field testing suggests initial content validity of a Spanish-language instrument to measure genetic knowledge relative to type 2 diabetes. ^ Keywords. Latinos, genetic knowledge, instrument development, cognitive interviewing ^

Collection of data on plant height along the plant diversity gradient in the Jena Experiment (Main Experiment, time series since 2002)

This data set contains a time series of plant height measurements (vegetative and reproductive) from the main experiment plots of a large grassland biodiversity experiment (the Jena Experiment; see further details below). In addition, data on species specific plant heights for the main experiment are available from 2002. In the main experiment, 82 grassland plots of 20 x 20 m were established from a pool of 60 species belonging to four functional groups (grasses, legumes, tall and small herbs). In May 2002, varying numbers of plant species from this species pool were sown into the plots to create a gradient of plant species richness (1, 2, 4, 8, 16 and 60 species) and functional richness (1, 2, 3, 4 functional groups). Plots were maintained by bi-annual weeding and mowing. 1. Plant height was recorded, generally, twice a year just before biomass harvest (during peak standing biomass in late May and in late August). Methodologies of measuring height have varied somewhat over the years. In earlier year the streched plant height was measured, while in later years the standing height without streching the plant was measured. Vegetative height was measured either as the height of the highest leaf or as the length of the main axis of non-flowering plants. Regenerating height was measured either as the height of the highest flower on a plant or as the height of the main axis of flowering. Sampled plants were either randomly selected in the core area of plots or along transects in defined distances. For details refer to the description of individual years. Starting in 2006, also the plots of the management experiment, that altered mowing frequency and fertilized subplots (see further details in the general description of the Jena Experiment) were sampled. 2. Species specific plant height was recorded two times in 2002: in late July (vegetative height) and just before biomass harvest during peak standing biomass in late August (vegetative and regenerative height). For each plot and each sown species in the species pool, 3 plant individuals (if present) from the central area of the plots were randomly selected and used to measure vegetative height (non-flowering indviduals) and regenerative height (flowering individuals) as stretched height. Provided are the means over the three measuremnts per plant species per plot.

Oceanographical and meterological observations in the Westafrican area of upwelling during the 'Deutsche Nordatlantische Expedition' 1937

In 1937 the "Meteor" performed the cruises of the first part of the "Deutsche Nordatlantische Expedition". This publication treats seven stations of three-day-anchoring occupied during that time, five of which are located on the shelf, one on the continental slope and one on a ridge between the Capverde islands. The Bohnecke current meter, an instrument developed for the expedition, is described briefly and it's accuracy studied by comparing the measurements of two instruments which operated simultaneously at the same depth. It is shown that it is very sensitive for movements of the anchored ship because of the very short measuring intervall (2 minutes). The influence of the ship's movements could not be eliminated completely, the mode of using the instrument at different depths being unsuitable for this. Considering the stratification the accuracy of it's representation by the mean temperature and salinity distributionis studied. It is shown that under certain conditions a distribution estimated from observed values gives more exact results. This especially applies to the TS-diagram. Station Meteor336, located on the shelf near Cape Juby, shows temperatures 4 °C less than the open ocean and so belongs to the area of upwelling. During the observation period, however, internal tides are prominent. The diurnal component is of considerable influence, the distinction from inertial oscillations (25.5 hours) not being possible, however. Station Meteor341, on the shelf off Spanish-Sahara, gives an excellent example of the movements in the centre of the area of upwelling. Changing it's direction by 45° at the beginning of the measurements, the wind causes a change of current direction at all depths which, after some inertial oscillations (period 28.3 hours), settles down to a final value. At the beginning and the end of the observations the current at the upper depths is directed off-shore, the angle between current and wind being 22°, while at the lower depths it is orientated towards the shore. The depth of the upper homogenous layer gives the origin of the water transported upwards When during the inertial oscillations the current goes offshore at all depths temporarily, a sudden disturbance occurs in the temperature measurements. Station Meteor311 is located similar to station Meteor341 but was occupied one month earlier. At that time the wind situation was unnormal, the usual wind direction of 45° occuring at the end of the station. Therefore an unnormally high vertical shear of current speed and direction has been observed, the current vector being directed off-shore at the surface and near the bottom, towards the coast inbetween. The TS-diagram shows that the bottom water is replaced first so that upwelling does not occur during observation time. The state reached at the end of the station does not seem to be stable. Station Meteor369, on the continental slope, is governed by internal waves. Besides the internal tide of 12.4 hours a wave of 6.5 hour period is observed, being possibly amplified by the large bottom slope. In 40 - 60 m depth, where the thermocline is located, a wave with 3.3 hour period is observed which is argued to be an internal boundary wave. Station Meteor334 is located on the shelf NW of the mouth of the Senegal river. A marked temperature stratification, associated with large disturbances, and nearly constant salinity have been found there. The current was going slowly towards S or SW in the upper 20 - 30 m, towards N underneath. At the boundary of the current systems intense turbulence developed,including as it seems a water type of less salinity which is transported from the Senegal river by the lower current. Station Meteor327, located at 100 m depth between two of the Capverde islands, shows oceanic characteristics. The semidiurnal tide is found mainly, the diurnal component having considerable influence. Furtheron an internal wave of 6 hour period is seen the maximum amplitude of which is moving slowly downwards. Two possibilities of explaining it are discussed. Station Meteor366 is found in the area of ceasing winds off the coast of upper Guinea. The temperature there depends strongly on the depth, the salinity being nearly constant. The currents are divided into an upper and a lower system with large variations in both of them. A change of wind direction of nearly 90° is supposed to be the reason. The variations in salinity accordingly are interpreted as the influence of fresh water outflow from land which is felt in a different way at different wind directions. In the last section the daily changes in air and water temperature are studied. The upwelling having large influence on these, a centre of the area of upwelling can be located at about 100 miles north of Cape Blanc (Station Meteor311). The semidiurnal tidal component is compared with previous results for the Atlantic Ocean yielding considerable differences for the direction and time of occurence of the current maximum which might be due to the topographical influences around the shelf.

Development and Application of Improvements to the Tile-based Fisher Ratio Method and Fundamental Instrument Considerations for Non-targeted Analysis using Two-dimensional Gas Chromatography

Thesis (Ph.D.)--University of Washington, 2016-06

Modeling of Turbulent Natural Gas and Biogas Flames of the Delft Jet-in-Hot-Coflow Burner: Effects of Coflow Temperature, Fuel Temperature and Fuel Composition on the Flame Lift-Off Height

The structure of a turbulent non-premixed flame of a biogas fuel in a hot and diluted coflow mimicking moderate and intense low dilution (MILD) combustion is studied numerically. Biogas fuel is obtained by dilution of Dutch natural gas (DNG) with CO2. The results of biogas combustion are compared with those of DNG combustion in the Delft Jet-in-Hot-Coflow (DJHC) burner. New experimental measurements of lift-off height and of velocity and temperature statistics have been made to provide a database for evaluating the capability of numerical methods in predicting the flame structure. Compared to the lift-off height of the DNG flame, addition of 30 % carbon dioxide to the fuel increases the lift-off height by less than 15 %. Numerical simulations are conducted by solving the RANS equations using Reynolds stress model (RSM) as turbulence model in combination with EDC (Eddy Dissipation Concept) and transported probability density function (PDF) as turbulence-chemistry interaction models. The DRM19 reduced mechanism is used as chemical kinetics with the EDC model. A tabulated chemistry model based on the Flamelet Generated Manifold (FGM) is adopted in the PDF method. The table describes a non-adiabatic three stream mixing problem between fuel, coflow and ambient air based on igniting counterflow diffusion flamelets. The results show that the EDC/DRM19 and PDF/FGM models predict the experimentally observed decreasing trend of lift-off height with increase of the coflow temperature. Although more detailed chemistry is used with EDC, the temperature fluctuations at the coflow inlet (approximately 100K) cannot be included resulting in a significant overprediction of the flame temperature. Only the PDF modeling results with temperature fluctuations predict the correct mean temperature profiles of the biogas case and compare well with the experimental temperature distributions.

Influence of host plant structure and microclimate on the abundance and behaviour of Tephritid fly

Microclimate and host plant architecture significantly influence the abundance and behavior of insects. However, most research in this field has focused at the invertebrate assemblage level, with few studies at the single-species level. Using wild Solanum mauritianum plants, we evaluated the influence of plant structure (number of leaves and branches and height of plant) and microclimate (temperature, relative humidity, and light intensity) on the abundance and behavior of a single insect species, the monophagous tephritid fly Bactrocera cacuminata (Hering). Abundance and oviposition behavior were signficantly influenced by the host structure (density of foliage) and associated microclimate. Resting behavior of both sexes was influenced positively by foliage density, while temperature positively influenced the numbers of resting females. The number of ovipositing females was positively influenced by temperature and negatively by relative humidity. Feeding behavior was rare on the host plant, as was mating. The relatively low explanatory power of the measured variables suggests that, in addition to host plant architecture and associated microclimate, other cues (e.g., olfactory or visual) could affect visitation and use of the larval host plant by adult fruit flies. For 12 plants observed at dusk (the time of fly mating), mating pairs were observed on only one tree. Principal component analyses of the plant and microclimate factors associated with these plants revealed that the plant on which mating was observed had specific characteristics (intermediate light intensity, greater height, and greater quantity of fruit) that may have influenced its selection as a mating site.