Níquel em solo e plantas de milho cultivadas em área tratada com lodo de esgoto durante 15 anos consecutivos

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Atributos químicos e matéria orgânica em complexos florestais periodicamente inundados na restinga da marambaia - RJ

This study aimed to evaluate and characterize the chemical properties of soil organic matter under two periodically flooded forest formations on the island of Marambaia, Rio de Janeiro. These formations differ on the degree of soil water saturation, caused by the influence of water table, and in the (F1) formation presents the water table nearer the surface compared to the (F2) formation. Samples were collected in layers from 0.00 to 0.05, 0.05-0.10 and 0.10-0.20 m. The soil properties evaluated were: pH, H+ + Al+ 3, Ca+2, Mg+2, Na+, K+, P, N, total organic carbon (TOC) and base saturation (V%), humin carbon fraction (C-HUM), carbon of humic acid fraction (HAF-C) and fulvic acid fraction carbon (FAF-C). Statistically higher pH values were observed for F1. In F2 there are higher values of Mg+2, P, N and V% value. Correlation was found between the concentrations of Mg+2, N, humic acid and fulvic acid with water table in F1, and water table in F2 with Na+ and K+. Fraction C-HUM was more representative of the total organic carbon, followed by C-HAF and C-FAF. The TOC levels were higher in F1. The C /N ratio was lower in F2, with values ranging between 9 and 12, and F1 were found higher values of this relationship, ranging from 9 to 15. Among the pathways of formation of organic soils in both areas it appears that the major route for organic matter accumulation is the inheritance route.

Humic fractions of forest, pasture and maize crop soils resulting from microbial activity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Teores de nitrogênio no solo e nas frações da matéria orgânica sob diferentes sistemas de produção de milho

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação de compostos modelos visando propor um método de diferenciação de matéria orgânica lábil e recalcitrante em ambientes aquáticos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chromium in soil organic matter and cowpea after four consecutive annual applications of composted tannery sludge

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Formas de fósforo, substâncias húmicas e nitrogênio inorgânico em áreas da Amazônia ocidental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Spurenanalyse von Uran und Plutonium sowie Speziationsuntersuchungen an Plutonium mit massenspektrometrischen und kapillarelektrophoretischen Methoden

Die Elemente Uran und Plutonium besitzen seit Entdeckung der Kernspaltung und der technischen Nutzung der Kernenergie eine globale Bedeutung. So trägt Pu hauptsächlich zur Radiotoxizität von abgebrannten Brennelementen bei und erfordert im Falle einer Endlagerung in einer tiefen geologischen Formation einen sicheren Verschluss für bis zu einer Million Jahre. Das Wissen über die vorliegenden chemischen Spezies ist dabei entscheidend für das Verständnis der chemisch-physikalischen Wechselwirkungen im jeweiligen geochemischen System, insbesondere mit dem Wirtsgestein (hier Ton) und den allgegenwärtigen Huminstoffen (hier Fulvinsäure). Längerfristig sind so Vorhersagen über einen Transport des hochradioaktiven Abfalls nach Auslaugung und Austritt aus einem Endlager bis in die Biosphäre möglich. Gerade der Ultraspurenbereich, im Fernfeld eines Endlagers zu erwarten, ist dabei von besonderem Interesse. Darüber hinaus machen nuklearforensische Untersuchungen – in Hinblick auf illegal benutztes Nuklearmaterial, Schmuggel oder Nuklearterrorismus – zur Bestimmung der Herkunft, des Alters oder der Radiotoxizität isotopenselektive Nachweismethoden im Ultraspurenbereich notwendig. Im Rahmen dieser Arbeit wurden hierfür die Resonanzionisationsmassenspektrometrie (RIMS) zur isotopenselektiven Spuren- und Ultraspurenanalyse von U und Pu sowie die Kapillarelektrophorese (CE) gekoppelt an die induktiv gekoppelte Plasma (ICP)-Massenspektrometrie (CE-ICP-MS) zur Speziation von Pu eingesetzt. Für den isotopenselektiven Nachweis von Ultraspurenmengen von Uran mittels RIMS wurden vorbereitende Studien durchgeführt und mehrere zweifach resonante Anregungsleitern mit nicht-resonanter Ionisation untersucht. Eine Effizienz von ca. 10^-10 bei einer Nachweisgrenze von 10^12 Atomen U-238 konnte erzielt werden. In Zusammenarbeit mit dem Institut für Radiochemie, TU München, wurde mittels RIMS die Isotopenzusammensetzung von Plutonium, abgetrennt aus einem panzerbrechenden Urangeschoss aus dem Kosovokonflikt, bestimmt und dieses als Waffenplutonium mit einem Gehalt von 15 pg Pu-239/g Uran identifiziert. Rückschlüsse über Herkunft und Alter des Plutoniums konnten daraus gewonnen werden. Für Studien zur Umweltüberwachung von Plutonium in Rheinland-Pfalz wurden Grund-, Oberflächen- und Klärwasserproben mittels RIMS untersucht. Oberhalb der Nachweisgrenze von ca. 10^7 Atomen Pu-239/500 mL konnte kein signifikanter Gehalt bestimmt werden. Zusätzlich wurden Klärschlammproben untersucht, wobei in einer Probe 5,1*10^7 Atome Pu-239/g gemessen wurde, was auf eine Anreicherung von Pu im Klärschlamm aus großen Wasservolumina hindeuten könnte. Speziationsuntersuchungen von Plutonium in Kontakt mit Fulvinsäure und dem Tonmineral Kaolinit wurden in Hinblick auf die Wechselwirkungen im Umfeld eines nuklearen Endlagers durchgeführt. Die Redoxkinetik von Pu(VI) in Kontakt mit Gorleben-Fulvinsäure zeigt eine mit steigendem pH zunehmend schnellere und vollständige Reduktion und ein vergleichbares Verhalten zur Huminsäure. Für ein Plutoniumgemisch aus allen vier umweltrelevanten Oxidationsstufen in Kontakt mit Gorleben-Fulvinsäure konnte nach ca. 1 Monat Kontaktzeit eine fasst vollständige Reduktion zum tri- und tetravalenten Pu beobachtet werden. Sorptionsuntersuchungen der stabilsten Oxidationsstufe, Pu(IV), in Kontakt mit Kaolinit bei pH = 0 bis 13 im Konzentrationsbereich 10^-7 bis 10^-9 mol/L verdeutlichen das ausgeprägte Sorptionsverhalten von Pu(IV) (ca. 60% bis 90% Sorption) im umweltrelevanten pH-Bereich bei einem Einsetzen der Sorption bei pH = 0 bis 2. Im Rahmen des "Colloid and Radionuclide Retardation" (CRR) Experiments im Felslabor Grimsel, Schweizer Alpen, wurde in Zusammenarbeit mit dem Institut für Nukleare Entsorgung, Karlsruhe, die kolloidgetragene Migration von Pu(IV) in einem Grundwasserstrom durch Scherzonen im Granitgestein unter umweltrelevanten Bedingungen untersucht. Bei Zugabe von im Grundwasser stabilen Bentonitkolloiden – Bentonit wird als ein geeignetes Verschlussmaterial für nukleare Abfälle erforscht – konnte ein erhöhter Transport des Pu(IV) beobachtet werden, der durch Sorption des Pu an die mobilen Kolloide hervorgerufen wird. Zur Speziation von Plutonium im Ultraspurenbereich wurde im Rahmen dieser Arbeit an der Entwicklung der Kopplung der CE mit der sehr sensitiven RIMS gearbeitet. Das Prinzip der offline-Kopplung basiert auf dem Sammeln der zu unterschiedlichen Zeiten am Ende der Kapillare eluierten Oxidationsstufen in einzelnen Fraktionen. Aus jeder Fraktion wird ein eigenes Filament hergestellt und mit RIMS auf seinen Plutoniumgehalt untersucht. Eine erste Validierung der Methode konnte durch Bestimmung der Oxidationsstufenzusammensetzung eines bekannten Gemischs erfolgreich für einen Gehalt von ca. 6*10^9 Atome Pu-239 durchgeführt werden. Dies stellt einen möglichen Zugang zu dem erwarteten Konzentrationsbereich im Fernfeld eines Endlagers dar.

Speciation of tetravalent plutonium in contact with humic substances and kaolinite under environmental conditions

Plutonium represents the major contribution to the radiotoxicity of spent nuclear fuel over storage times of up to several hundred thousand years. The speciation of plutonium in aquifer systems is important in order to assess the risks of high-level nuclear waste disposal and to acquire a deep knowledge of the mobilization and immobilization behavior of plutonium. In aqueous solutions, plutonium can coexist in four oxidation states and each one of them has different chemical and physical behavior. Tetravalent plutonium is the most abundant under natural conditions. Therefore, detailed speciation studies of tetravalent plutonium in contact with humic substances (HS) and kaolinite as a model clay mineral have been performed in this work. Plutonium is present in the environment at an ultratrace level. Therefore, speciation of Pu at the ultratrace level is mandatory. Capillary electrophoresis (CE) coupled to resonance ionization mass spectrometry (RIMS) was used as a new speciation method. CE-RIMS enables to improve the detection limit for plutonium species by 2 to 3 orders of magnitude compared to the previously developed CE-ICP-MS. For understanding the behavior of Pu(IV) in aqueous systems, redox reactions, complexation, and sorption behavior of plutonium were studied. The redox behavior of plutonium in contact with humic acid (HA) and fulvic acid (FA) was investigated. A relatively fast reduction of Pu(VI) in contact with HS was observed. It was mainly reduced to Pu(IV) and Pu(III) within a couple of weeks. The time dependence of the Pu(IV) complexation with Aldrich HA was investigated and a complex constant (logßLC) between 6.4 - 8.4 of Pu(IV) was determined by means of ultrafiltration taking into account the loading capacity (LC). The sorption of tetravalent plutonium onto kaolinite was investigated as a function of pH in batch experiments under aerobic and anaerobic conditions. The sorption edge was found at about pH = 1 and a maximum sorption at around pH = 8.5. In the presence of CO2 at pH > 8.5, the sorption of plutonium was decreased probably due to the formation of soluble carbonate complexes. For comparison, the sorption of Th(IV) onto kaolinite was also investigated and consistent results were found. The Pu(IV) sorption onto kaolinite was studied by XANES and EXAFS at pH 1, 4, 9 and the sorbed species on kaolinite surface was Pu(IV). Depending on the pH, only 1 - 10 % of the sorbed plutonium is desorbed from kaolinite and released into a fresh solution at the same pH value. Furthermore, the sorption of HS onto kaolinite was studied as a function of pH at varying concentrations of HS, as a prerequisite to understand the more complex ternary system. The sorption of HA onto kaolinite was found to be higher than that of FA. The investigation of the ternary systems (plutonium-kaolinite-humic substances) is performed as a function of pH, concentration of HS, and the sequences of adding the reactants. The presence of HS strongly influences the sorption of Pu(IV) onto kaolinite over the entire pH range. For comparison, the influence of HS on the sorption of Th(IV) onto kaolinite was also investigated and a good agreement with the results of Pu(IV) was obtained.

Laboratory study on the optical properties of absorbing atmospheric aerosols and field applications

The interaction between aerosols and sun light plays an important role in the radiative balance of Earth’s atmosphere. This interaction is obtained by measuring the removal (extinction), redistribution (scattering), and transformation into heat (absorption) of light by the aerosols; i.e. their optical properties. Knowledge of these properties is crucial for our understanding of the atmospheric system. rn Light absorption by aerosols is a major contributor to the direct and indirect effects on our climate system, and an accurate and sensitive measurement method is crucial to further our understanding. A homebuilt photoacoustic sensor (PAS), measuring at a 532nm wavelength, was fully characterized and its functionality validated for measurements of absorbing aerosols. The optical absorption cross-sections of absorbing polystyrene latex spheres, to be used as a standard for aerosol absorption measurements, were measured and compared to literature values. Additionally, a calibration method using absorbing aerosol of known complex refractive index was presented.rn A new approach to retrieve the effective broadband refractive indices (mbroad,eff) of aerosol particles by a white light aerosol spectrometer (WELAS) optical particle counter (OPC) was achieved. Using a tandem differential mobility analyzer (DMA)-OPC system, the nbroad,eff are obtained for both laboratory and field applications. This method was tested in the laboratory using substances with a wide range of optical properties and it was used in ambient measurements to retrieve the nbroad,eff of biomass burning aerosols in a nationwide burning event in Israel. The retrieved effective broadband refractive indices for laboratory generated scattering aerosols were: ammonium sulfate (AS), glutaric acid (GA), and sodium chloride, all within 4% of literature values. For absorbing substances, nigrosine and various mixtures of nigrosine with AS and GA were measured, as well as a lightly absorbing substance, Suwannee river fulvic acid (SRFA). For the ambient measurements, the calibration curves generated from this method were to follow the optical evolution of biomass burning (BB) aerosols. A decrease in the overall aerosol absorption and scattering for aged aerosols during the day after the fires compared to the smoldering phase of the fires was found. rn The connection between light extinction of aerosols, their chemical composition and hygroscopicity for particles with different degrees of absorption was studied. The extinction cross-section (σext) at 532nm for different mobility diameters was measured at 80% and 90% relative humidity (RH), and at an RH<10%. The ratio of the humidified aerosols to the dry ones, fRHext(%RH,Dry), is presented. For purely scattering aerosols, fRHext(%RH,Dry) is inversely proportional with size; this dependence was suppressed for lightly absorbing ones. In addition, the validity of the mixing rules for water soluble absorbing aerosols is explored. The difference between the derived and calculated real parts of the complex RIs were less than 5.3% for all substances, wavelengths, and RHs. The obtained imaginary parts for the retrieved and calculated RIs were in good agreement with each other, and well within the measurement errors of retrieval from pulsed CRD spectroscopy measurements. Finally, a core-shell structure model is also used to explore the differences between the models, for substances with low growth factors, under these hydration conditions. It was found that at 80% RH and for size parameters less than 2.5, there is less than a 5 % difference between the extinction efficiencies calculated with both models. This difference is within measurement errors; hence, there is no significant difference between the models in this case. However, for greater size parameters the difference can be up to 10%. For 90% RH the differences below a size parameter of 2.5 were up to 7%.rn Finally, the fully characterized PAS together with a cavity ring down spectrometer (CRD), were used to study the optical properties of soot and secondary organic aerosol (SOA) during the SOOT-11 project in the AIDA chamber in Karlsruhe, Germany. The fresh fractal-like soot particles were allowed to coagulate for 28 hours before stepwise coating them with SOA. The single scattering albedo for fresh fractal-like soot was measured to be 0.2 (±0.03), and after allowing the soot to coagulate for 28 hours and coating it with SOA, it increased to 0.71(±0.01). An absorption enhancement of the coated soot of up to 1.71 (±0.03) times from the non-coated coagulated soot was directly measured with the PAS. Monodisperse measurements of SOA and soot coated with SOA were performed to derive the complex refractive index (m) of both aerosols. A complex refractive index of m = 1.471(±0.008) + i0.0(±0.002) for the SOA-αO3 was retrieved. For the compact coagulated soot a preliminary complex refractive index of m = 2.04(+0.21/-0.14) + i0.34(+0.18/-0.06) with 10nm(+4/-6) coating thickness was retrieved.rn These detail properties can be use by modelers to decrease uncertainties in assessing climatic impacts of the different species and to improve weather forecasting.rn

Organic geochemistry of DSDP Leg 41 holes

The black shale encountered in Cretaceous cores of the Cape Verde area during the DSDP Leg 41 are of marine origin and correspond to excellent potential oil source rocks. They have a low content of humic compounds. Pyrolysis assays, chloroformic extracts, and kerogen data attest to a relatively low stage of evolution for samples at Site 367 (Cape Verde Basin). The samples from Site 368 (Cape Verde Rise) are more evolved, and the deeper ones would be located at the beginning of the principal zone of oil formation.

Do decomposing organic matter residues reduce phosphorus sorption in highly weathered soils?

Many studies have shown a reduction in P sorption in highly weathered soils when organic matter (OM) is applied, suggesting competition between OM decomposition products and P for sorption sites. However, such studies seldom consider the P released from the added OM. To delineate the effects of OM addition on P availability through sorption competition and P addition, water leachate from incubated soybean (SB) [Glycine mar (L.) Merr.] and Rhodes grass (RG) (Chloris gayana Knuth cv. Callide) was used in competitive P sorption studies both undiluted and after acidification (i.e., the fulvic acid [FA] component). Addition of two rates (0.2 and 2 mL) of SB leachate to an Oxisol significantly increased P sorption at the higher rate, while a similar trend was observed following RG leachate addition at the same rates. Extending the range of highly weathered soils examined (two Oxisols, an Ultisol, and an acidic Vertisol) resulted in no observed decrease in P sorption following addition of OM leachate. Surprisingly, SB leachate transiently increased P sorption in the two Oxisol soils. Addition of the FA component of the leachates resulted in a transient (< 6 d) decrease in P sorption in three of the four soils examined and constituted the only evidence in this study that decomposing OM residues reduced P sorption. This research provides further evidence contradicting the long held assumption that inhibition of P sorption by dissolved organic compounds, derived from decomposing OM, is responsible for increased P phytoavailability when P fertilizer and OM are applied together.

Molecular characterization of Cladium peat from the Florida Everglades: biomarker associations with humic fractions

The accumulation and preservation of peat soils in Everglades freshwater marshes and mangrove swamps is an essential process in the ecological functioning of these ecosystems. Human intervention and climate change have modified nutrient dynamics and hydroperiod in the Everglades and peat loss due to such anthropogenic activities is evident. However, not much is known on the molecular level regarding the biogeochemical characteristics, which allow peat to be preserved in the Everglades. Lipid biomarkers trapped within or bound to humic-type structures can provide important geochemical information regarding the origin and microbial transformation of OM in peat. Four lipid fractions obtained from a Cladium peat, namely the freely extractable fraction and those associated with humin, humic acid, and fulvic acid fractions, showed clear differences in their molecular distribution suggesting different OM sources and structural and diagenetic states of the source material. Both, higher plant derived and microbial lipids were found in association with these humic-type substances. Most biomarker distributions suggest an increment in the microbial/terrestrial lipid ratio from the free to humin to humic to fulvic fractions. Microbial reworking of lipids, and the incorporation of microbial biomarkers into the humic-type fractions was evident, as well as the preservation of diagenetic byproducts. The lipid distribution associated with the fulvic acids suggests a high degree of microbial reworking for this fraction. Evidence for this 3D structure was obtained through the presence of the relatively high abundance of α,ω-dicarboxylic acids and phenolic and benzenecarboxylic compounds. The increment in structural complexity of the phenolic and benzencarboxylic compounds in combination with the reduction in the carbon chain length of the dicarboxylic acids from the free to fulvic fraction suggests the latter to be structurally the most stable, compacted and diagenetically altered substrate. This analytical approach can now be applied to peat samples from other areas within the Everglades ecosystem, affected differently by human intervention with the aim to assess changes in organic matter preservation.

Effects of Natural Organic Matter on the Dissolution Kinetics and Bioavailability of Metal Oxide Nanoparticles

The rapid development of nanotechnology and wider applications of engineered nanomaterials (ENMs) in the last few decades have generated concerns regarding their environmental and health risks. After release into the environment, ENMs undergo aggregation, transformation, and, for metal-based nanomaterials, dissolution processes, which together determine their fate, bioavailability and toxicity to living organisms in the ecosystems. The rates of these processes are dependent on nanomaterial characteristics as well as complex environmental factors, including natural organic matter (NOM). As a ubiquitous component of aquatic systems, NOM plays a key role in the aggregation, dissolution and transformation of metal-based nanomaterials and colloids in aquatic environments.

The goal of this dissertation work is to investigate how NOM fractions with different chemical and molecular properties affect the dissolution kinetics of metal oxide ENMs, such as zinc oxide (ZnO) and copper oxide (CuO) nanoparticles (NPs), and consequently their bioavailability to aquatic vertebrate, with Gulf killifish (Fundulus grandis) embryos as model organisms.

ZnO NPs are known to dissolve at relatively fast rates, and the rate of dissolution is influenced by water chemistry, including the presence of Zn-chelating ligands. A challenge, however, remains in quantifying the dissolution of ZnO NPs, particularly for time scales that are short enough to determine rates. This dissertation assessed the application of anodic stripping voltammetry (ASV) with a hanging mercury drop electrode to directly measure the concentration of dissolved Zn in ZnO NP suspensions, without separation of the ZnO NPs from the aqueous phase. Dissolved zinc concentration measured by ASV ([Zn]ASV) was compared with that measured by inductively coupled plasma mass spectrometry (ICP-MS) after ultracentrifugation ([Zn]ICP-MS), for four types of ZnO NPs with different coatings and primary particle diameters. For small ZnO NPs (4-5 nm), [Zn]ASV was 20% higher than [Zn]ICP-MS, suggesting that these small NPs contributed to the voltammetric measurement. For larger ZnO NPs (approximately 20 nm), [Zn]ASV was (79±19)% of [Zn]ICP-MS, despite the high concentrations of ZnO NPs in suspension, suggesting that ASV can be used to accurately measure the dissolution kinetics of ZnO NPs of this primary particle size.

Using the ASV technique to directly measure dissolved zinc concentration, we examined the effects of 16 different NOM isolates on the dissolution kinetics of ZnO NPs in buffered potassium chloride solution. The observed dissolution rate constants (kobs) and dissolved zinc concentrations at equilibrium increased linearly with NOM concentration (from 0 to 40 mg-C L-1) for Suwannee River humic acid (SRHA), Suwannee River fulvic acid and Pony Lake fulvic acid. When dissolution rates were compared for the 16 NOM isolates, kobs was positively correlated with certain properties of NOM, including specific ultraviolet absorbance (SUVA), aromatic and carbonyl carbon contents, and molecular weight. Dissolution rate constants were negatively correlated to hydrogen/carbon ratio and aliphatic carbon content. The observed correlations indicate that aromatic carbon content is a key factor in determining the rate of NOM-promoted dissolution of ZnO NPs. NOM isolates with higher SUVA were also more effective at enhancing the colloidal stability of the NPs; however, the NOM-promoted dissolution was likely due to enhanced interactions between surface metal ions and NOM rather than smaller aggregate size.

Based on the above results, we designed experiments to quantitatively link the dissolution kinetics and bioavailability of CuO NPs to Gulf killifish embryos under the influence of NOM. The CuO NPs dissolved to varying degrees and at different rates in diluted 5‰ artificial seawater buffered to different pH (6.3-7.5), with or without selected NOM isolates at various concentrations (0.1-10 mg-C L-1). NOM isolates with higher SUVA and aromatic carbon content (such as SRHA) were more effective at promoting the dissolution of CuO NPs, as with ZnO NPs, especially at higher NOM concentrations. On the other hand, the presence of NOM decreased the bioavailability of dissolved Cu ions, with the uptake rate constant negatively correlated to dissolved organic carbon concentration ([DOC]) multiplied by SUVA, a combined parameter indicative of aromatic carbon concentration in the media. When the embryos were exposed to CuO NP suspension, changes in their Cu content were due to the uptake of both dissolved Cu ions and nanoparticulate CuO. The uptake rate constant of nanoparticulate CuO was also negatively correlated to [DOC]×SUVA, in a fashion roughly proportional to changes in dissolved Cu uptake rate constant. Thus, the ratio of uptake rate constants from dissolved Cu and nanoparticulate CuO (ranging from 12 to 22, on average 17±4) were insensitive to NOM type or concentration. Instead, the relative contributions of these two Cu forms were largely determined by the percentage of CuO NP that was dissolved.

Overall, this dissertation elucidated the important role that dissolved NOM plays in affecting the environmental fate and bioavailability of soluble metal-based nanomaterials. This dissertation work identified aromatic carbon content and its indicator SUVA as key NOM properties that influence the dissolution, aggregation and biouptake kinetics of metal oxide NPs and highlighted dissolution rate as a useful functional assay for assessing the relative contributions of dissolved and nanoparticulate forms to metal bioavailability. Findings of this dissertation work will be helpful for predicting the environmental risks of engineered nanomaterials.

On the microstructure, growth pattern and original porosity of belemnite rostra: insights from calcitic Jurassic belemnites

Calcitic belemnite rostra are usually employed to perform paleoenvironmental studies based on geochemical data. However, several questions, such as their original porosity and microstructure, remain open, despite they are essential to make accurate interpretations based on geochemical analyses.This paper revisits and enlightens some of these questions. Petrographic data demonstrate that calcite crystals of the rostrum solidum of belemnites grow from spherulites that successively develop along the apical line, resulting in a “regular spherulithic prismatic” microstructure. Radially arranged calcite crystals emerge and diverge from the spherulites: towards the apex, crystals grow until a new spherulite is formed; towards the external walls of the rostrum, the crystals become progressively bigger and prismatic. Adjacent crystals slightly vary in their c-axis orientation, resulting in undulose extinction. Concentric growth layering develops at different scales and is superimposed and traversed by a radial pattern, which results in the micro-fibrous texture that is observed in the calcite crystals in the rostra.Petrographic data demonstrate that single calcite crystals in the rostra have a composite nature, which strongly suggests that the belemnite rostra were originally porous. Single crystals consistently comprise two distinct zones or sectors in optical continuity: 1) the inner zone is fluorescent, has relatively low optical relief under transmitted light (TL) microscopy, a dark-grey color under backscatter electron microscopy (BSEM), a commonly triangular shape, a “patchy” appearance and relatively high Mg and Na contents; 2) the outer sector is non-fluorescent, has relatively high optical relief under TL, a light-grey color under BSEM and low Mg and Na contents. The inner and fluorescent sectors are interpreted to have formed first as a product of biologically controlled mineralization during belemnite skeletal growth and the non-fluorescent outer sectors as overgrowths of the former, filling the intra- and inter-crystalline porosity. This question has important implications for making paleoenvironmental and/or paleoclimatic interpretations based on geochemical analyses of belemnite rostra.Finally, the petrographic features of composite calcite crystals in the rostra also suggest the non-classical crystallization of belemnite rostra, as previously suggested by other authors.