Global analysis of aerodynamics deflectors efficiency in the grinding process

The conventional, grinding methods in some cases are not very efficient because the arising of thermal damages in the pieces is very common. Optimization methods of cutting fluid application in the grinding zone are essential to prevent thermal problems from interaction of the wheel grains with the workpiece. surface. The optimization can happen through the correct selection of the cut parameters and development of devices that eliminate air layer effects generated around the grinding wheel. This article will collaborate with the development of an experimentation methodology which allows evaluating, comparatively, the performance of the deflectors in the cutting region to minimize the air layer effect of the high speed of the grinding wheel. The air layers make the cutting fluid jet to dissipate in the machine. An optimized nozzle was used in order to compare the results with the conventional method (without baffles or deflectors) of cutting fluid application. The results showed the high eficciency of the deflectors or baffles in the finish results. Copyright © 2006 by ABCM.

Grinding of hardened steels using optimized cooling

Grinding - the final machining process of a workpiece - requires large amounts of cutting fluids for the lubrication, cooling and removal of chips. These fluids are highly aggressive to the environment. With the technological advances of recent years, the worldwide trend is to produce increasingly sophisticated components with very strict geometric and dimensional tolerances, good surface finish, at low costs, and particularly without damaging the environment. The latter requirement can be achieved by recycling cutting fluids, which is a costly solution, or by drastically reducing the amount of cutting fluids employed in the grinding process. This alternative was investigated here by varying the plunge velocity in the plunge cylindrical grinding of ABNT D6 steel, rationalizing the application of two cutting fluids and using a superabrasive CBN (cubic boron nitride) grinding wheel with vitrified binder to evaluate the output parameters of tangential cutting force, acoustic emission, roughness, roundness, tool wear, residual stress and surface integrity, using scanning electron microscopy (SEM) to examine the test specimens. The performance of the cutting fluid, grinding wheel and plunge velocity were analyzed to identify the best machining conditions which allowed for a reduction of the cutting fluid volume, reducing the machining time without impairing the geometric and dimensional parameters, and the surface finish and integrity of the machined components.

Influência das técnicas de mínima quantidade de lubrificante, refrigeração otimizada e refrigeração convencional na qualidade de peças produzidas com aços endurecidos no processo de retificação

The influence of minimum lubrication, optimized and conventional cooling at different flows and application rates of cutting fluids on the quality of hardened-steel pieces produced by external cylindrical plunge grinding with super-abrasive grinding wheels with low CBN concentrations was verified. The analysis of the quality of the pieces was performed through the assessment of the behavior of the specific energy of the grinding, roughness, roundness deviation, and the generated residual stress. By analyzing of the application ways and of the several flows and application rates of the cutting fluid, one could encounter lubrication/cooling conditions that enable the reduction in cutting fluid volume, reduction in grinding time without compromising the dimensional parameters (superficial finishing, surface integrity). Regarding the different applications of cutting fluids, it could be noted the optimized application for higher velocities has presented the best performance, demonstrating the effectiveness of the new concept of nozzle utilized.

Analysis on turning Ti-6Al-4V with different cooling methods

The aim of this paper is to optimize the machining of Ti-6Al-4V alloy, by studying the chip formation, roughness and tool wear for different cooling conditions. The results were compared between cooling methods, minimal quantity of fluid (MQF) and flooding, and also without fluid for the tool H13A. The turning of Ti-6Al-4V has shown good results on roughness (0, 8μm) and tool life, which was 11% lower with MQF than with the flooding method. The tool wear causes variation of the shear angle, which promotes strength hardening of the chip. As a result, the machined surface could be damaged. The use of the cutting fluid helps to save the cutting edge and could reduce the strength hardening. Nevertheless, it could also facilitate the formation of built-up edge. The nucleation of alpha lamellar colonies can occur due to a combination of deformation rates and temperature, mainly when the flooding is used, but it's not conclusive. The lamellar colonies were also found with the MQF in some regions, however, this structure did not show hardness variation compared to equiaxial. For all this reasons, the machining parameters might be carefully chosen.

Retificação da alumina com rebolo diamantado usando diferentes métodos de lubri-refrigeração

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo comparativo entre a lubri-refrigeração convencional e a MQL no processo de retificação cilíndrica externa de mergulho

Pós-graduação em Engenharia Mecânica - FEB

Estudo e caracterização do processo de usinagem do compóstio GLARE

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelagem térmica para avaliação da temperatura no fresamento de aços para moldes e matrizes

Pós-graduação em Engenharia Mecânica - FEIS

Portaferramentas para torneamento com refrigeração interna baseada na mudança de fase do fluido

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise da influência da profundidade de corte e de diferentes métodos de lubri-refrigeração na retificação plana de aço ABNT 4340

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização da mínima quantidade de lubrificante (MQL) com água no processo de retificação cilíndrica externa de mergulho de cerâmicas com rebolo diamantado

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Comparação entre os métodos convencional e com bocal modificado de aplicação de fluido de corte no processo de retificação cilíndrica interna

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da matriz polimérica e dos métodos de extração de corpos de prova em compósitos de fibra de carbono

Pós-graduação em Engenharia Mecânica - FEB

Análise da influência da velocidade de mergulho na retificação de aços endurecidos utilizando refrigeração otimizada

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização da técnica da mínima quantidade de lubrificante (MQL) com adição de água no processo de retificação cilíndrica externa de aços endurecidos com rebolos de CBN

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)