Otimização do tempo e temperatura no processamento da gipsita oriunda dos cristalizadores da produção de sal para obter gesso de uso na construção civil

During the process of the salt production, the first the salt crystals formed are disposed of as industrial waste. This waste is formed basically by gypsum, composed of calcium sulfate dihydrate (CaSO4.2H2O), known as carago cru or malacacheta . After be submitted the process of calcination to produce gypsum (CaSO4.0,5H2O), can be made possible its application in cement industry. This work aims to optimize the time and temperature for the process of calcination of the gypsum (carago) for get beta plaster according to the specifications of the norms of civil construction. The experiments involved the chemical and mineralogical characterization of the gypsum (carago) from the crystallizers, and of the plaster that is produced in the salt industry located in Mossoró, through the following techniques: x-ray diffraction (XRD), x-ray fluorescence (FRX), thermogravimetric analysis (TG/DTG) and scanning electron microscopy (SEM) with EDS. For optimization of time and temperature of the process of calcination was used the planning three factorial with levels with response surfaces of compressive mechanical tests and setting time, according norms NBR-13207: Plasters for civil construction and x-ray diffraction of plasters (carago) beta obtained in calcination. The STATISTICA software 7.0 was used for the calculations to relate the experimental data for a statistical model. The process for optimization of calcination of gypsum (carago) occurred in the temperature range from 120° C to 160° C and the time in the range of 90 to 210 minutes in the oven at atmospheric pressure, it was found that with the increase of values of temperature of 160° C and time calcination of 210 minutes to get the results of tests of resistance to compression with values above 10 MPa which conform to the standard required (> 8.40) and that the X-ray diffractograms the predominance of the phase of hemidrato beta, getting a beta plaster of good quality and which is in accordance with the norms in force, giving a by-product of the salt industry employability in civil construction

Remote Sensing Detection of atmospheric pollutants using Lidar, Sodar and correlation with air quality data in an industrial area

Optical remote sensing techniques have obvious advantages for monitoring gas and aerosol emissions, since they enable the operation over large distances, far from hostile environments, and fast processing of the measured signal. In this study two remote sensing devices, namely a Lidar (Light Detection and Ranging) for monitoring the vertical profile of backscattered light intensity, and a Sodar (Acoustic Radar, Sound Detection and Ranging) for monitoring the vertical profile of the wind vector were operated during specific periods. The acquired data were processed and compared with data of air quality obtained from ground level monitoring stations, in order to verify the possibility of using the remote sensing techniques to monitor industrial emissions. The campaigns were carried out in the area of the Environmental Research Center (Cepema) of the University of São Paulo, in the city of Cubatão, Brazil, a large industrial site, where numerous different industries are located, including an oil refinery, a steel plant, as well as fertilizer, cement and chemical/petrochemical plants. The local environmental problems caused by the industrial activities are aggravated by the climate and topography of the site, unfavorable to pollutant dispersion. Results of a campaign are presented for a 24- hour period, showing data of a Lidar, an air quality monitoring station and a Sodar. © 2011 SPIE.

Avaliação preliminar do emprego de arenito zeolítico da região nordeste do Brasil como material pozolânico para cimento Portland

As zeolitas possuem atividade pozolânica normalmente sem a necessidade de ativação térmica, por isto têm sido empregadas na produção de cimento e concreto hidráulicos desde a época do império romano. Hoje em dia são utilizadas na fabricação do cimento Portland através da substituição do clinquer em percentuais que variam entre 5 e 20%, dependendo da reatividade e da finura da zeólita. Em razão disto, são muito importantes do ponto de vista econômico e ambiental, principalmente quando não necessitam de tratamento térmico para adquirirem caráter pozolânico satisfatório, porque reduzem significativamente a energia de produção do clinquer e a liberação de CO₂ proveniente tanto da descarbonatação da calcita como da combustão de combustíveis fósseis. Contudo, dados sobre reservas de zeólitas naturais são escassos e imprecisos. No Brasil, não existe conhecimento sobre depósitos naturais de zeólitas que possam ser explorados comercialmente. No nordeste do Brasil existe a ocorrência de zeolitas sedimentares relacionadas a arenitos descoberta nos anos 2000. Estes arenitos são constituídos de quartzo, argilominerais e zeolitas naturais (estilbita). O objetivo geral desse trabalho foi avaliar se esta zeólita natural presente no arenito possui atividade pozolânica satisfatória para ser empregada como adição mineral em cimentos Portland. No programa experimental o arenito zeolítico passou por beneficiamento através da remoção, por peneiramento, do quartzo e outros minerais inertes, de modo a concentrar a zeólita estilbita e com isto verificar as propriedades pozolânicas deste mineral. No estudo experimental foram empregadas as técnicas de difração de raios X, calorimetria, ensaios químicos e de determinação da atividade pozolânica em argamassas de cal hidratada e cimento Portland. Os resultados mostraram que o arenito zeolítico acelerou a hidratação do cimento Portland devido a extrema finura do material. O arenito apresentou atividade pozolânica, sendo a estilbita responsável por este comportamento. Entretanto, a reatividade foi ligeiramente inferior ao mínimo exigido para ser empregado em escala industrial como pozolana. Estudos complementares são necessários para averiguar se o tratamento térmico entre 300 °C e 500 °C pode aumentar a atividade pozolânica do arenito devido a destruição da estrutura cristalina tanto da estilbita quanto da esmectita presente no arenito.

Caracterização dos resíduos cauliníticos das indústrias de mineração de caulim da Amazônia como matéria-prima para produção de pozolanas de alta reatividade

As regiões do Rio Capim e do Rio Jari são os principais distritos caulinitícos da Região Amazônica, detentores das maiores reservas brasileiras de caulim de alta qualidade para aplicações como cobertura de papel. O caulim é lavrado e beneficiado por três grandes companhias que são responsáveis pela geração de aproximadamente 500 mil de toneladas anuais de um resíduo decorrente da etapa de centrifugação. Esse resíduo, na forma de polpa, é depositado em lagoas de sedimentação que ocupam grandes extensões de áreas. O objetivo da pesquisa foi investigar as características físicas, químicas e mineralógicas dos resíduos processados da Região do Jari e do Capim, de modo a avaliar se atendem aos requisitos como matéria-prima para a produção de uma pozolana de alta reatividade, o metacaulim, adição mineral que incorporada ao cimento Portland proporciona alto desempenho às misturas de concreto e argamassas. Os resíduos foram caracterizados por difração de raios X, análise térmica, espectroscopia de infravermelho, microscopia eletrônica de varredura, fluorescência de raios X e difração a laser. Ambos os resíduos são constituídos por no mínimo 92% de caulinita de baixa granulometria, cujas áreas superficiais específicas são superiores a 8 m²/g e os diâmetros médios de partículas inferiores a 1 µm. Os teores de sílica livre (quartzo) não foram superiores a 3%. O alto grau de concentração de caulinita destes resíduos dispensa os rígidos parâmetros de controle de remoção de impurezas, normalmente empregados na produção deste tipo de pozolana. O caulim do Rio Jari, com quantidade de defeitos na estrutura cristalina superior ao da caulinita do Rio Capim, proporcinou maior grau de desidroxilação a uma temperatura mais baixa quando calcinado, indicando a possibilidade de redução de gastos com energia para a produção da adição mineral. Os resultados das análises foram convergentes e apontam ambos os caulins estudados como excelentes matérias-primas para a produção do metacaulim de alta reatividade.

Tubos de concreto com adição de resíduos de borracha de pneu

Pós-graduação em Engenharia Civil - FEIS

Mordenite from Spain and its application as pozzolana

In Spain, natural zeolites have been only found in the volcanic areas of Canary Islands (San Gil, M.M., 1959). However, several years ago the study of the South Eastern region of continental Spain (Cabo de Gata) revealed the presence of a deposit of mordenite being industrially commercialized as bentonite. The deposit San José-Los Escullos is located in the concession registered as Los Murcianos, managed by Bentonitas Especiales, S.A. (BENESA) who was extracting bentonite while ignoring the presence of the zeolite. The name San José-Los Escullos refers to the discovery of mordenite in this deposit. The deposit is located in a volcanic area, constituted by pyroxenic andesites, breccias, tuffs, pyroclasts with andesitic and dacitic composition, largely altered by the hydrothermal solutions. The recent discovery of this zeolite with mordenite content up to 97%, has changed the initial vision about that deposit, and new possible uses of this mineral in the pozzolanic cement industry are foreseen. This work intends to give preliminary data on the characterization of this zeolite according to X-ray diffraction (XRD), ICP analyses, and scanning electron microscopy (SEM), as well as to emphasize the pozzolanic properties of this material, using both chemical and mechanical tests.

Contaminantes orgánicos (PAHs) derivados de la escombrera de la Central Térmica de Aliaga (Teruel)

The aim of this study was to determine if the soils, waters and plants from the Aliaga dump contained polycyclic aromatic hydrocarbons (PAHs) and their quantification.The results showed that PAHs concentrations in soils are in general higher than the reference levels from the Spanish legislation. Waters and plants contained PAHs but in low concentrations. The possible actions for remediation (photodegradation and bioremediation) seem to be unviable here because of the large volume of materials involved, although its use as an additive for the cement industry and derivatives can be considered. It is proposed that fluorantene in waters, and phenanthrene and benzo[ghi]perilene in soils be considered as pollutants as well as to study the incorporation of PAHs to plants. Key-words: Polycyclic aromatic hydrocarbons, soil, plant and water contamination, fly- ash, power plant. RESUMEN: El objetivo de este estudio fue determinar y cuantificar los hidrocarburos policíclicos aromáticos (PAHs) en los suelos, plantas y aguas de la Escombrera de Aliaga. La concentración de PAHs en las cenizas supera, en general, los valores establecidos en la legislación española.Las aguas y plantas contienen PAHs, aunque en concentraciones bajas. La remoción de los materiales para someterlos a fotodegradación y biorremediación es inviable debido al gran volumen de la escombrera, aunque se plantea su uso como aditivo en la fabricación de productos derivados del cemento. Se propone incluir el fenantreno y benzo[ghi]perileno en la normativa de suelos, así como el naftaleno en la de aguas y la elaboración de una legislación sobre la incorporación de estos compuestos a las plantas.

Constitution, by-laws and rules of order of the American Brotherhood of Cementworkers ...

"Adopted by the first convention of the American Brotherhood of Cement Workers, June 18, 1903."

Medidas de concentração de radônio proveniente de argamassas de cimento portland, gesso e fosfogesso

Portland cement being very common construction material has in its composition the natural gypsum. To decrease the costs of manufacturing, the cement industry is substituting the gypsum in its composition by small quantities of phosphogypsum, which is the residue generated by the production of fertilizers and consists essentially of calcium dihydrate and some impurities, such as fluoride, metals in general, and radionuclides. Currently, tons of phosphogypsum are stored in the open air near the fertilizer industries, causing contamination of the environment. The 226 Ra present in these materials, when undergoes radioactive decay, produces the 222Rn gas. This radioactive gas, when inhaled together with its decay products deposited in the lungs, produces the exposure to radiation and can be a potential cause of lung cancer. Thus, the objective of this study was to measure the concentration levels of 222Rn from cylindrical samples of Portland cement, gypsum and phosphogypsum mortar from the state of Paraná, as well as characterizer the material and estimate the radon concentration in an environment of hypothetical dwelling with walls covered by such materials. Experimental setup of 222Rn activity measurements was based on AlphaGUARD detector (Saphymo GmbH). The qualitative and quantitative analysis was performed by gamma spectrometry and EDXRF with Au and Ag targets tubes (AMPTEK), and Mo target (ARTAX) and mechanical testing with x- ray equipment (Gilardoni) and the mechanical press (EMIC). Obtained average values of radon activity from studied materials in the air of containers were of 854 ± 23 Bq/m3, 60,0 ± 7,2 Bq/m3 e 52,9 ± 5,4 Bq/m3 for Portland cement, gypsum and phosphogypsum mortar, respectively. These results extrapolated into the volume of hypothetical dwelling of 36 m3 with the walls covered by such materials were of 3366 ± 91 Bq/m3, 237 ± 28 Bq/m3 e 208 ± 21 Bq/m3for Portland cement, gypsum and phosphogypsum mortar, respectively. Considering the limit of 300 Bq/m3 established by the ICRP, it could be concluded that the use of Portland cement plaster in dwellings is not secure and requires some specific mitigation procedure. Using the results of gamma spectrometry there were calculated the values of radium equivalent activity concentrations (Raeq) for Portland cement, gypsum and phosphogypsum mortar, which were obtained equal to 78,2 ± 0,9 Bq/kg; 58,2 ± 0,9 Bq/kg e 68,2 ± 0,9 Bq/kg, respectively. All values of radium equivalent activity concentrations for studied samples are below the maximum level of 370 Bq/kg. The qualitative and quantitative analysis of EDXRF spectra obtained with studied mortar samples allowed to evaluate quantitate and the elements that constitute the material such as Ca, S, Fe, and others.

In-situ Molibdenum X-ray powder diffraction study of the early hydration of cementitious systems on a humidity chamber

The durability of cement-based construction materials depends on the environmental conditions during their service life. A further factor is the microstructure of the cement bulk, established by formation of cement hydrates. The development of the phases and microstructure under given conditions is responsible of the high strength of cementitious materials. The investigation on the early hydration behavior of cements and cementing systems has been for a long time a very important area of research: understanding the chemical reactions that lead to hardening is fundamental for the prediction of performances and durability of the materials. The production of 1 ton of Ordinary Portland Cement, OPC, releases into the atmosphere ~0.97 tons of CO2. This implies that the overall CO2 emissions from the cement industry are 6% of all anthropogenic carbon dioxide. An alternative to reduce the CO2 footprint consists on the development of eco-cements composed by less calcite demanding phases, such as belite and ye'elimite. That is the case of Belite-Ye’elimite cements (BY). Since the reactivity of belite is not quick enough, these materials develop low mechanical strengths at intermediate hydration ages. A possible solution to this problem goes through the production of cements which jointly contain alite with the two previously mentioned phases, named as Belite-Alite-Ye’elimite (BAY) cements. The reaction of alite and ye'elimite with water will develop cements with high mechanical strengths at early ages, while belite will contribute to later values. The final goal is to understand the hydration mechanisms of a variety of cementing systems (OPC, BAY and pure phases) as a function of water content, superplasticizer additives and type and content of sulfate source. In order to do so, in-situ laboratory humidity chambers with Molybdenum X-ray Powder diffraction are employed. In the first 2h of hydration, reaction degree (α) of ye'elimite had been decreased for superplasticizer.

Análise comparativa entre as propriedades do gesso obtido de rejeito da produção de sal e gesso comerciais

The environmental impacts, caused by the solid residues generation, are an often quoted concern nowadays. Some of these residues, which are originated from different human activities, can be fully reused, reducing the effects of the poor waste management on the environment. During the salt production process, the first formed crystals are discarded as industrial waste. This is mainly made of gypsum that is a calcium sulfate dihydrate (CaSO4.2H2O). The gypsum in question may go through a calcination process due to the plaster (CaSO4.0,5H2O) production and then the application on the cement industry. Considering the necessity of development and application for these industrial wastes, this paper aims to analyze the plaster, called Salgesso, from the gypsum that was generated during the salt production, and its use viability on the civil construction industry in order to create environmental and economical benefits. For characterization, the following experiments were performed: X-ray Fluorescence (XRF), X-ray Diffraction (XRD), thermal analysis (TG/DTG) and Scanning Electron Microscopy (SEM) with EDS. The following tests were also performed to obtain the mechanical characteristics: Thinness Modulus, Unit Mass, Setting Time and Compressive Resistance. Three commercial plasters used on civil construction were taken as references. All of these tests were performed according to the current standards. It was noticed that although there were some conflicting findings between the salt and commercial plasters in all of the studied properties, the Salgesso has its values within the standard limits. However, there is the possibility to improve them by doing a more effective calcination process. Three commercial plasters, used in construction, were used as reference material. All tests were performed according to standards in force. It was observed that although some tests present conflicting findings between the salt and gypsum plasters commercial properties in all of the studied Salgesso have values within the limits imposed by the standard, but can be improved simply by calcination process more effective

Performance of concrete incorporating amorphous silica residue and biomass fly ash

L'industrie du ciment est l'une des principales sources d'émission de dioxyde de carbone. L'industrie mondiale du ciment contribue à environ 7% des émissions de gaz à effet de serre dans l'atmosphère. Afin d'aborder les effets environnementaux associés à la fabrication de ciment exploitant en permanence les ressources naturelles, il est nécessaire de développer des liants alternatifs pour fabriquer du béton durable. Ainsi, de nombreux sous-produits industriels ont été utilisés pour remplacer partiellement le ciment dans le béton afin de générer plus d'économie et de durabilité. La performance d'un additif de ciment est dans la cinétique d'hydratation et de la synergie entre les additions et de ciment Portland. Dans ce projet, deux sous-produits industriels sont étudiés comme des matériaux cimentaires alternatifs: le résidu de silice amorphe (RSA) et les cendres des boues de désencrage. Le RSA est un sous-produit de la production de magnésium provenant de l'Alliance Magnésium des villes d'Asbestos et Thedford Mines, et les cendres des boues de désencrage est un sous-produit de la combustion des boues de désencrage, l'écorce et les résidus de bois dans le système à lit fluidisé de l'usine de Brompton située près de Sherbrooke, Québec, Canada. Récemment, les cendres des boues de désencrage ont été utilisées comme des matériaux cimentaires alternatifs. L'utilisation de ces cendres comme matériau cimentaire dans la fabrication du béton conduit à réduire la qualité des bétons. Ces problèmes sont causés par des produits d'hydratation perturbateurs des cendres volantes de la biomasse quand ces cendres sont partiellement mélangées avec du ciment dans la fabrication du béton. Le processus de pré-mouillage de la cendre de boue de désencrage avant la fabrication du béton réduit les produits d'hydratation perturbateurs et par conséquent les propriétés mécaniques du béton sont améliorées. Les approches pour étudier la cendre de boue de désencrage dans ce projet sont : 1) caractérisation de cette cendre volante régulière et pré-humidifiée, 2) l'étude de la performance du mortier et du béton incorporant cette cendre volante régulière et pré-humidifiée. Le RSA est un nouveau sous-produit industriel. La haute teneur en silice amorphe en RSA est un excellent potentiel en tant que matériau cimentaire dans le béton. Dans ce projet, l'évaluation des RSA comme matériaux cimentaires alternatifs compose trois étapes. Tout d'abord, la caractérisation par la détermination des propriétés minéralogiques, physiques et chimiques des RSA, ensuite, l'optimisation du taux de remplacement du ciment par le RSA dans le mortier, et enfin l'évaluation du RSA en remplacement partiel du ciment dans différents types de béton dans le système binaire et ternaire. Cette étude a révélé que le béton de haute performance (BHP) incorporant le RSA a montré des propriétés mécaniques et la durabilité, similaire du contrôle. Le RSA a amélioré les propriétés des mécaniques et la durabilité du béton ordinaire (BO). Le béton autoplaçant (BAP) incorporant le RSA est stable, homogène et a montré de bonnes propriétés mécaniques et la durabilité. Le RSA avait une bonne synergie en combinaison de liant ternaire avec d'autres matériaux cimentaires supplémentaires. Cette étude a montré que le RSA peut être utilisé comme nouveaux matériaux cimentaires dans le béton.

A reactividade do clinquer

A indústria cimenteira é uma indústria com grandes gastos energéticos, sendo por Isso de extrema importância, do ponto de vista económico, desenvolver estratégias e procedimentos que conduzam à sua minimização. O intuito da realização do presente trabalho foi estudar a reactividade do clínquer da Cimpor­ Centro de Produção de Loulé, ao introduzir alterações ao processo de fabrico de cimento. O estudo engloba três objectivos: C. Melhorar a qualidade do clínquer; C. Reduzir o consumo térmico do forno; C. Reduzir o consumo energético dos moinhos de cimento. Na paragem de Maio de 2008 foi instalado um novo redutor para o motor do forno que permitiu alterar a velocidade máxima de 2 para 3,5 rpm, o que consequentemente diminuiu a taxa de enchimento de ≈20% para ≈14%. Os resultados mostraram que com a alteração ao processo atingiram-se dois dos três objectivos pretendidos. Isto é, obteve-se um clínquer de melhor qualidade e houve uma diminuição do consumo térmico do forno. Contudo, não se conseguiram tirar conclusões acerca do consumo energético dos moinhos de cimento, sendo para tal, necessário prolongar o tempo do estudo. ABSTRACT: The cement industry is an industry with high energy costs and is therefore of extreme importance, in economic terms, to develop strategies and procedures that lead to its minimization. The purpose of this work was to study the reactivity of the clinker produced at Loulé Cimpor Production Center by introducing changes in the manufacture process of cement. The study comprised three main objectives: C. Improving the quality of the clinker; C. Reducing the heat consumption of the furnace; C. Reducing energy consumption of the cement mills. During the stop of May 2008 a new reducer was installed in the furnace motor which allowed changing the maximum speed of 2 to 3.5 rpm, which consequently decreased the rate of filling from ≈20% to ≈14%. The results showed that with the process modification, two of the three objectives were reached up. That is, a better quality of clinker was obtained and there was a decrease in the heat consumption of the furnace. However, during the period of this study it was not possible to draw a final conclusion about the energy consumption of the cement mills, and therefore, it is necessary to study the process for a longer period of time.

Brazilian sugar cane bagasse ashes from the cogeneration industry as active pozzolans for cement manufacture

For proper management of wastes and their possible recycling as raw materials, complete characterization of the materials is necessary to evaluate the main scientific aspects and potential applications. The current paper presents a detailed scientific study of different Brazilian sugar cane bagasse ashes from the cogeneration industry as alternative cementing materials (active addition) for cement manufacture. The results show that the ashes from the industrial process (filter and bottom ones) present different chemical and mineralogical compositions and pozzolanic properties as well. As a consequence of its nature, the kinetic rate constant (K) states that the pozzolanic activity is null for the bottom ash and very low for the filter ash with respect to a sugar cane bagasse ash obtained in the laboratory under controlled burning conditions (reference). The scarce pozzolanic activity showed by ashes could be related to a possible contamination of bagasse wastes (with soils) before their use as alternative combustibles. For this reason, an optimization process for these wastes is advisable, if the ashes are to be used as pozzolans. (C) 2011 Elsevier Ltd. All rights reserved.