The effect of housing characteristics and occupant activities on the respiratory health of women and children in Lao PDR

The paper presents the results of a study conducted into the relationship between dwelling characteristics and occupant activities with the respiratory health of resident women and children in Lao People’s Democratic Republic (PDR). Lao is one of the least developed countries in south-east Asia with poor life expectancies and mortality rates. The study, commissioned by the World Health Organisation, included questionnaires delivered to residents of 356 dwellings in nine districts in Lao PDR over a five month period (December 2005-April 2006), with the aim of identifying the association between respiratory health and indoor air pollution, in particular exposures related to indoor biomass burning. Adjusted odds ratios were calculated for each health outcome separately using binary logistic regression. After adjusting for age, a wide range of symptoms of respiratory illness in women and children aged 1-4 years were positively associated with a range of indoor exposures related to indoor cooking, including exposure to a fire and location of the cooking place. Among women, “dust always inside the house” and smoking were also identified as strong risk factors for respiratory illness. Other strong risk factors for children, after adjusting for age and gender, included dust and drying clothes inside. This analysis confirms the role of indoor air pollution in the burden of disease among women and children in Lao PDR.

Patterns of correlation between vehicle occupant seat pressure and anthropometry

Seat pressure is known as a major factor of seat comfort in vehicles. In passenger vehicles, there is lacking research into the seat comfort of rear seat occupants. As accurate seat pressure measurement requires significant effort, simulation of seat pressure is evolving as a preferred method. However, analytic methods are based on complex finite element modeling and therefore are time consuming and involve high investment. Based on accurate anthropometric measurements of 64 male subjects and outboard rear seat pressure measurements in three different passenger vehicles, this study investigates if a set of parameters derived from seat pressure mapping are sensitive enough to differentiate between different seats and whether they correlate with anthropometry in linear models. In addition to the pressure map analysis, H-Points were measured with a coordinate measurement system based on palpated body landmarks and the range of H-Point locations in the three seats is provided. It was found that for the cushion, cushion contact area and cushion front area/force could be modeled by subject anthropometry,while only seatback contact area could be modeled based on anthropometry for all three vehicles. Major differences were found between the vehicles for other parameters.

Opinions, attitudes and driving experiences of car and racing "enthusiasts" : results of the Ontario Car and Racing Club Survey

In recent years, car club and racing websites and forums have become an increasingly popular way for car enthusiasts to access racing and car club news, chat-rooms and message boards. However, no North American research has been found that has examined opinions and driving experiences of car and racing enthusiasts. The purpose of this study was to examine car club members’ opinions about and experiences with various aspects of driving, road safety and traffic legislation, with a particular focus on street racing. A web-based questionnaire (Survey Monkey) was developed using the expert panel method and was primarily based on validated instruments or questions that were developed from other surveys. The questionnaire included: 1) driver concerns regarding traffic safety issues and legislation; 2) attitudes regarding various driving activities; 3) leisure-time activities, including club activities; 4) driving experiences, including offences and collisions; and 5) socio-demographic questions. The survey was pre- tested and piloted. Electronic information letters were sent out to an identified list of car clubs and forums situated in southern Ontario. Car club participants were invited to fill out the questionnaire. This survey found that members of car clubs share similar concerns regarding various road safety issues with samples of Canadian drivers, although a smaller percentage of car club members are concerned about speeding-related driving. Car club members had varied opinions regarding Ontario’s Street Racers, Stunt and Aggressive Drivers Legislation. The respondents agreed the most with the new offences regarding not sitting in the driver’s seat, having a person in the trunk, or driving as close as possible to another vehicle, pedestrian or object on or near the highway without a reason. The majority disagreed with police powers of impoundment and on-the-spot licence suspensions. About three quarters of respondents reported no collisions or police stops for traffic offences in the past five years. Of those who had been stopped, the most common offence was reported as speeding. This study is the first in Canada to examine car club members’ opinions about and experiences with various aspects of driving, road safety and traffic legislation. Given the ubiquity of car clubs and fora in Canada, insights on members’ opinions and practices provide important information to road safety researchers.

Determinants of driver vs. second row occupant posture modelling

Digital human modeling (DHM), as a convenient and cost-effective tool, is increasingly incorporated into product and workplace design. In product design, it is predominantly used for the development of driver-vehicle systems. Most digital human modeling software tools, such as JACK, RAMSIS and DELMIA HUMANBUILDER provide functions to predict posture and positions for drivers with selected anthropometry according to SAE (Society of Automotive Engineers) Recommended Practices and other ergonomics guidelines. However, few studies have presented 2nd row passenger postural information, and digital human modeling of these passenger postures cannot be performed directly using the existing driver posture prediction functions. In this paper, the significant studies related to occupant posture and modeling were reviewed and a framework of determinants of driver vs. 2nd row occupant posture modeling was extracted. The determinants which are regarded as input factors for posture modeling include target population anthropometry, vehicle package geometry and seat design variables as well as task definitions. The differences between determinants of driver and 2nd row occupant posture models are significant, as driver posture modeling is primarily based on the position of the foot on the accelerator pedal (accelerator actuation point AAP, accelerator heel point AHP) and the hands on the steering wheel (steering wheel centre point A-Point). The objectives of this paper are aimed to investigate those differences between driver and passenger posture, and to supplement the existing parametric model for occupant posture prediction. With the guide of the framework, the associated input parameters of occupant digital human models of both driver and second row occupant will be identified. Beyond the existing occupant posture models, for example a driver posture model could be modified to predict second row occupant posture, by adjusting the associated input parameters introduced in this paper. This study combines results from a literature review and the theoretical modeling stage of a second row passenger posture prediction model project.

The contribution of seat components to seat hardness and the interface between human occupant and a driver seat

Effective digital human model (DHM) simulation of automotive driver packaging ergonomics, safety and comfort depends on accurate modelling of occupant posture, which is strongly related to the mechanical interaction between human body soft tissue and flexible seat components. This paper comprises: a study investigating the component mechanical behaviour of a spring-suspended, production level seat when indented by SAE J826 type, human thigh-buttock representing hard shell; a model of seated human buttock shape for improved indenter design using a multivariate representation of Australian population thigh-buttock anthropometry; and a finite-element study simulating the deflection of human buttock and thigh soft tissue when seated, based on seated MRI. The results of the three studies provide a description of the mechanical properties of the driver-seat interface, and allow validation of future dynamic simulations, involving multi-body and finite-element (FE) DHM in virtual ergonomic studies.

Evaluation of the Type I child car restraints fitting service in WA

Child passenger injury remains a major road safety issue despite advances in biomechanical understanding and child restraint design. In Australia, one intervention with parents to encourage universal and consistent use of the most appropriate restraint as well as draw their attention to critical aspects of installation is the RoadWise Type 1 Child Car Restraints Fitting Service, WA. A mixed methods evaluation of this service was conducted in early 2010. Evaluation results suggest that it has been effective in ensuring good quality training of child restraint fitters. In addition, stakeholder and user satisfaction with the Service is high, with participants agreeing that the Service is valuable to the community, and fitters regarding the training course, materials and post-training support as effective. However, a continuing issue for interventions of this type is whether the parents who need them perceive this need. Evidence from the evaluation suggests that only about 25% of parents who could benefit from the Service actually use it. This may be partly due to parental perceptions that such services are not necessary or relevant to them, or to overconfidence about the ease of installing restraints correctly. Thus there is scope for improving awareness of the Service amongst groups most likely to benefit from it (e.g. new parents) and for alerting parents to the importance of correct installation and getting their self-installed restraints checked. Efforts to inform and influence parents should begin when their children are very young, preferably at or prior to birth and/or before the parent installs the first restraint.

A behavioural car-following model that captures traffic oscillations

This paper presents a behavioral car-following model based on empirical trajectory data that is able to reproduce the spontaneous formation and ensuing propagation of stop-and-go waves in congested traffic. By analyzing individual drivers’ car-following behavior throughout oscillation cycles it is found that this behavior is consistent across drivers and can be captured by a simple model. The statistical analysis of the model’s parameters reveals that there is a strong correlation between driver behavior before and during the oscillation, and that this correlation should not be ignored if one is interested in microscopic output. If macroscopic outputs are of interest, simulation results indicate that an existing model with fewer parameters can be used instead. This is shown for traffic oscillations caused by rubbernecking as observed in the US 101 NGSIM dataset. The same experiment is used to establish the relationship between rubbernecking behavior and the period of oscillations.

A safety adapted car following model for traffic safety studies

Traffic safety studies demand more than what current micro-simulation models can provide as they presume that all drivers exhibit safe behaviors. All the microscopic traffic simulation models include a car following model. This paper highlights the limitations of the Gipps car following model ability to emulate driver behavior for safety study purposes. A safety adapted car following model based on the Gipps car following model is proposed to simulate unsafe vehicle movements, with safety indicators below critical thresholds. The modifications are based on the observations of driver behavior in real data and also psychophysical notions. NGSIM vehicle trajectory data is used to evaluate the new model and short following headways and Time To Collision are employed to assess critical safety events within traffic flow. Risky events are extracted from available NGSIM data to evaluate the modified model against them. The results from simulation tests illustrate that the proposed model can predict the safety metrics better than the generic Gipps model. The outcome of this paper can potentially facilitate assessing and predicting traffic safety using microscopic simulation.

The social car : new interactive vehicular applications derived from social media and urban informatics

Digital information that is place- and time-specific, is increasingly becoming available on all aspects of the urban landscape. People (cf. the Social Web), places (cf. the Geo Web), and physical objects (cf. ubiquitous computing, the Internet of Things) are increasingly infused with sensors, actuators, and tagged with a wealth of digital information. Urban informatics research explores these emerging digital layers of the city at the intersection of people, place and technology. However, little is known about the challenges and new opportunities that these digital layers may offer to road users driving through today’s mega cities. We argue that this aspect is worth exploring in particular with regards to Auto-UI’s overarching goal of making cars both safer and more enjoyable. This paper presents the findings of a pilot study, which included 14 urban informatics research experts participating in a guided ideation (idea creation) workshop within a simulated environment. They were immersed into different driving scenarios to imagine novel urban informatics type of applications specific to the driving context.

Evaluation of the GHR car following model for traffic safety studies

Traffic safety studies mandate more than what existing micro-simulation models can offer as they postulate that every driver exhibits a safe behaviour. All the microscopic traffic simulation models are consisting of a car-following model and the Gazis–Herman–Rothery (GHR) car-following model is a widely used model. This paper highlights the limitations of the GHR car-following model capability to model longitudinal driving behaviour for safety study purposes. This study reviews and compares different version of the GHR model. To empower the GHR model on precise metrics reproduction a new set of car-following model parameters is offered to simulate unsafe vehicle conflicts. NGSIM vehicle trajectory data is used to evaluate the new model and short following headways and Time to Collision are employed to assess critical safety events within traffic flow. Risky events are extracted from available NGSIM data to evaluate the modified model against the generic versions of the GHR model. The results from simulation tests illustrate that the proposed model does predict the safety metrics better than the generic GHR model. Additionally it can potentially facilitate assessing and predicting traffic facilities’ safety using microscopic simulation. The new model can predict Near-miss rear-end crashes.

Comparison and modification of car following models toward a more accurate microscopic simulation parameters reproduction

Traffic safety studies demand more than what current micro-simulation models can provide as they presume that all drivers of motor vehicles exhibit safe behaviours. Several car-following models are used in various micro-simulation models. This research compares the mainstream car following models’ capabilities of emulating precise driver behaviour parameters such as headways and Time to Collisions. The comparison firstly illustrates which model is more robust in the metric reproduction. Secondly, the study conducted a series of sensitivity tests to further explore the behaviour of each model. Based on the outcome of these two steps exploration of the models, a modified structure and parameters adjustment for each car-following model is proposed to simulate more realistic vehicle movements, particularly headways and Time to Collision, below a certain critical threshold. NGSIM vehicle trajectory data is used to evaluate the modified models performance to assess critical safety events within traffic flow. The simulation tests outcomes indicate that the proposed modified models produce better frequency of critical Time to Collision than the generic models, while the improvement on the headway is not significant. The outcome of this paper facilitates traffic safety assessment using microscopic simulation.

I just want to design a sexy flying car! Teaching design-led innovation to designers

Many international management programs have capitalised on the value design can have upon potential business solutions and strategies (Martin, 2009 & Brown, 2008) as well as many international design programs introducing designers to business theory and curriculum (Manzini & Rizzo, 2011). This paper presents the findings from structured interviews with undergraduate design students and design industry professionals. Current literature surrounding design led innovation and the role designers’ play within it is also discussed and the challenges facing designers in this emerging design era are presented. The findings from this study indicate that most designers enter an undergraduate program not wanting to become the business leaders of tomorrow. Instead, they enter in the hope they can humbly help people and to make a difference in the world. There are contentions with this perspective, felt by industry, academia and students around why designers need to be taught business theory content. This paper provides the first step to overcoming this challenge by providing insight into the attitudes, perceptions and challenges designers are facing with this new design era.

Occupant comfort, the housing industry and electricity infrastructure : understanding the synergies

Despite increasingly stringent energy performance regulations for new homes, southeast Queensland has a high and growing penetration of, and reliance on, air conditioners to provide thermal comfort to housing inhabitants. This reliance impacts on electricity infrastructure investment which is the key driving force behind rising electricity prices. This paper reports initial findings of a research project that seeks to better understand three key issues: (i) how families manage their thermal comfort in summer and how well their homes limit overheating; (ii) the extent to which the homes have been constructed according to the building approval documentation; and (iii) the impact that these issues have on urban design, especially in relation to electricity infrastructure in urban developments.

Does 2-wheeler experience affect behaviours and attitudes to 2-wheelers as a car driver?

• Car-bicycle and car-motorcycle crashes often serious • Car driver mostly at fault, often because of failure to see (Schramm et al, 2010) • Car drivers with motorcycling experience less likely to be involved in motorcycle crashes or be at fault (Brooks & Guppy, 1990; Magazzu et al., 2006) and hold more positive beliefs about motorcyclists (Crundall et al., 2008) • Does bicycle riding experience have the same benefits?

Bus and car travel time on urban networks : integrating Bluetooth and bus vehicle identification data

Travel time in an important transport performance indicator. Different modes of transport (buses and cars) have different mechanical and operational characteristics, resulting in significantly different travel behaviours and complexities in multimodal travel time estimation on urban networks. This paper explores the relationship between bus and car travel time on urban networks by utilising the empirical Bluetooth and Bus Vehicle Identification data from Brisbane. The technologies and issues behind the two datasets are studied. After cleaning the data to remove outliers, the relationship between not-in-service bus and car travel time and the relationship between in-service bus and car travel time are discussed. The travel time estimation models reveal that the not-in-service bus travel time are similar to the car travel time and the in-service bus travel time could be used to estimate car travel time during off-peak hours