Uuteaineiden on-line-mittaus koivusulfaattisellutehtaalla

Tämän työn tarkoituksena oli tutkia pihkanhallintaa sulfaattisellutehtaalla ja uuteaineiden analysointimenetelmiä massasta ja suodoksesta. Tavoitteena oli kehittää uuteaineiden on-line mittausmenetelmä sulfaattisellutehtaalle. Kirjallisuusosassa esitettiin sulfaattisellun valmistusprosessi ja uuteaineiden käyttäytyminen prosessissa. Lisäksi työssä käsiteltiin tärkeimpiä pihkanhallintamenetelmiä ja uuteaineiden analysointia. Kokeellisessa osassa määritettiin uuteainepitoisuudet 29:stä massa- ja pesusuodosnäytteestä. Lisäksi suodosnäytteiden sameus ja kemiallinen hapenkulutus määritettiin laboratoriossa. On-line mittaukset tehtiin DD-pesurin paluusuodoksesta, josta mitattiin johtokyky, lämpötila, taitekerroin ja pH. Sameutta yritettiin mitata on-line nefelometrillä, mutta käytössä ollut laite ei soveltunut tumman suodoksen mittaamiseen. Työssä saatujen tulosten perusteella voidaan todeta, että pesusuodoksen ominaisuuksia mittaamalla ei voida arvioida massan uutepitoisuutta luotettavasti. Suodoksen ja massan uutepitoisuuksien välinen selitysaste oli 54%. Saippuoitumattomien uuteaineiden pitoisuuden ollessa erityisen suuri, suodoksen uutepitoisuus ei korreloi massassa olevan uutteen määrän kanssa. Täten kyseinen mittausmenetelmä ei ole sopiva, sillä se ei toimi silloin, kun olisi tärkeintä tietää oikea uuteainepitoisuus pihkanhallintakemikaalien annosten määrittämiseksi. Suodoksen sameus riippui sen uutepitoisuudesta 80% selitysasteella. Sameusmittaus on nopea ja suhteellisen luotettava menetelmä suodosten uutepitoisuuksien arviointiin, mutta se vaatii mittalaitteen joka käyttää usean ilmaisimen tekniikkaa. On-line-mittauksissa laitteisto tulisi varustaa automaattisella pesulaitteella, sillä mittarin linssit likaantuvat helposti prosessivirrassa.

Measurement Problems and Problem-Solving in Kraft Pulping

Tämän työn tarkoituksena on koota yhteen selluprosessin mittausongelmat ja mahdolliset mittaustekniikat ongelmien ratkaisemiseksi. Pääpaino on online-mittaustekniikoissa. Työ koostuu kolmesta osasta. Ensimmäinen osa on kirjallisuustyö, jossa esitellään nykyaikaisen selluprosessin perusmittaukset ja säätötarpeet. Mukana on koko kuitulinja puunkäsittelystä valkaisuun ja kemikaalikierto: haihduttamo, soodakattila, kaustistamo ja meesauuni. Toisessa osassa mittausongelmat ja mahdolliset mittaustekniikat on koottu yhteen ”tiekartaksi”. Tiedot on koottu vierailemalla kolmella suomalaisella sellutehtaalla ja haastattelemalla laitetekniikka- ja mittaustekniikka-asiantuntijoita. Prosessikemian paremmalle ymmärtämiselle näyttää haastattelun perusteella olevan tarvetta, minkä vuoksi konsentraatiomittaukset on valittu jatkotutkimuskohteeksi. Viimeisessä osassa esitellään mahdollisia mittaustekniikoita konsentraatiomittausten ratkaisemiseksi. Valitut tekniikat ovat lähi-infrapunatekniikka (NIR), fourier-muunnosinfrapunatekniikka (FTIR), online-kapillaarielektroforeesi (CE) ja laserindusoitu plasmaemissiospektroskopia (LIPS). Kaikkia tekniikoita voi käyttää online-kytkettyinä prosessikehitystyökaluina. Kehityskustannukset on arvioitu säätöön kytketylle online-laitteelle. Kehityskustannukset vaihtelevat nollasta miestyövuodesta FTIR-tekniikalle viiteen miestyövuoteen CE-laitteelle; kehityskustannukset riippuvat tekniikan kehitysasteesta ja valmiusasteesta tietyn ongelman ratkaisuun. Työn viimeisessä osassa arvioidaan myös yhden mittausongelman – pesuhäviömittauksen – ratkaisemisen teknis-taloudellista kannattavuutta. Ligniinipitoisuus kuvaisi nykyisiä mittauksia paremmin todellista pesuhäviötä. Nykyään mitataan joko natrium- tai COD-pesuhäviötä. Ligniinipitoisuutta voidaan mitata UV-absorptiotekniikalla. Myös CE-laitetta voitaisiin käyttää pesuhäviön mittauksessa ainakin prosessikehitysvaiheessa. Taloudellinen tarkastelu pohjautuu moniin yksinkertaistuksiin ja se ei sovellu suoraan investointipäätösten tueksi. Parempi mittaus- ja säätöjärjestelmä voisi vakauttaa pesemön ajoa. Investointi ajoa vakauttavaan järjestelmään on kannattavaa, jos todellinen ajotilanne on tarpeeksi kaukana kustannusminimistä tai jos pesurin ajo heilahtelee eli pesuhäviön keskihajonta on suuri. 50 000 € maksavalle mittaus- ja säätöjärjestelmälle saadaan alle 0,5 vuoden takaisinmaksuaika epävakaassa ajossa, jos COD-pesuhäviön vaihteluväli on 5,2 – 11,6 kg/odt asetusarvon ollessa 8,4 kg/odt. Laimennuskerroin vaihtelee tällöin välillä 1,7 – 3,6 m3/odt asetusarvon ollessa 2,5 m3/odt.

Integration of a Bioethanol Process to a Pulp Mill

Tässä diplomityössä tutkittiin puuhakkeen esihydrolyysi- ja hakkuujätteen hydrolyysiprosessien integroimista sellutehtaaseen bioetanolin tuottamiseksi. Tällaisesta ns. biojalostamosta luotiin WinGEMS-simulointiohjelmalla simulointimalli, jonka avulla tutkittiin bioetanoliprosessin vaikutusta sellutehtaan massa- ja energiataseisiin sekä alustavaa biojalostamon kannattavuutta. Simuloinnissa tarkasteltiin kolmea eri tapausta, joissa mäntysellun tuotannon ajateltiin olevan 1000 tonnia päivässä ja hakkuujätettä käytettävän 10 % tarvittavan kuitupuun määrästä: 1) Puuhakkeen esihydrolyysi ja hakkuujätteen hydrolyysi etanolin tuottamiseksi 2) Puuhakkeen esihydrolyysi, hakkuujäte kuorikattilaan poltettavaksi 3) Ei esihydrolyysiä, hakkuujäte kuorikattilaan poltettavaksi Verrattuna tapaukseen 3, puun kulutus kasvaa 16 % esihydrolysoitaessa puuhake ennen keittoa tapauksissa 1 ja 2. Kasvaneella puun kulutuksella tuotetaan tapauksessa 1 149 tonnia etanolia ja 240 MWh enemmän ylimääräsähköä päivässä. Tapauksessa 2 tuotetaan 68 tonnia etanolia ja 460 MWh enemmän ylimääräsähköä päivässä. Tämä tuottaisi vuotuista lisäkassavirtaa 18,8 miljoonaa euroa tapauksessa 1 ja 9,4 miljoonaa euroa tapauksessa 2. Hydrolyysin tuoteliuoksen, hydrolysaatin, haihduttaminen sekä hydrolyysiprosessien orgaanisten jäännöstuotteiden haihduttaminen ja polttaminen kasvattavat haihduttamon ja soodakattilan kuormitusta. Verrattuna tapaukseen 3, tapauksissa 1 ja 2 haihduttamon vaiheiden määrä on kasvatettava viidestä seitsemään ja tarvittavat lämmönsiirtopinta-alat lähes kaksinkertaistettava. Soodakattilan kuormitus kasvaa 39 % tapauksessa 1 ja 26 % tapauksessa 2.

The Impact of Aspen and Alder on the Quality of NHBK

The purpose of this work was to study the effect of aspen and alder on birch cooking and the quality of the pulp produced. Three different birch kraft pulps were studied. As a reference, pure aspen and alder were included. The laboratory trials were done at the UPM Research Centre in Lappeenranta, Finland. The materials used were birch, aspen and alder mill chips that were collected around the area of South-Carelia in Finland. The chips used in the study were pulped using a standard kraft process. The pulps including birch fibres were ECF-bleached at laboratory scale to a target brightness of 85 %. The bleached pulps were beaten at low consistency by a laboratory Voith Sulzer refiner and tested for optical and physical properties. The theoretical part is a study of hardwoods that takes into accounts the differences between birch, aspen and alder. Major sub-areas were fibre and paper-technical properties as well as chemical composition and their influence on the different properties. The pulp properties of birch, aspen and alder found in previous studies were reported. Russian hardwood forest resources were also investigated. The fundamentals of kraft pulping and bleaching were studied at the end of theoretical part. The major effect of replacing birch with aspen and alder was the deterioration (lowering) of tensile and tear strengths. In other words, addition of aspen and alder to a birch furnish reduced strength properties. The reinforcement ability of the tested pulps was the following: 100 % birch > 80 % birch, 20 % aspen > 70 % birch, 20 % aspen, 10 % alder. The second thing noted was that blending of birch together with aspen and alder give better smoothness, optical properties and also formation. It can be concluded, that replacement of birch with alder during cooking by more than 10 % can negatively affect on the paper-technical properties of birch pulp. Mixing pure birch and aspen pulps would be more beneficial when producing printing paper made from chemical pulp.

Branqueamento de polpa celulósica kraft de eucalipto com peróxido ácido ativado por molibdênio

Optimum conditions to run the P Mo stage for bleaching eucalyptus kraft pulp were 90 ºC, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H2O2. The P Mo stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 ºC), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P Mo stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO.

Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill

Tension (TW) and opposite wood (OW) of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively). The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes) were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EO)D1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.

Ultrafiltration of pulp mill bleaching effluents

Main objective of this research was to find suitable polymeric ultrafiltration membranes with high retentions, good capacities and low fouling tendencies for the E2- and EP-effluent ultrafiltration. Purpose was to treat alkaline bleaching effluents with ultrafiltration in a way that permeates of the filtrations could be recycled back to process and the consumption of fresh water in the pulp mill could be reduced significantly. In the theoretical part of this work the challenges set by the pulp and paper indus-try processes for membranes were examined. An overview of the membrane tech-nology in the pulp industry was also provided. In addition process conditions in the chemical pulp bleaching and properties of bleaching effluents were discussed in literature study. In experimental part the E2- and EP-stage bleaching effluents from Stora Enso Imatra kraft pulp mill were ultrafiltered with CR250- and CR200-filters. Suitable membranes for ultrafiltration were chosen after screening experiments. Concentra-tion experiment was made for the E2-effluent in order to estimate water saving potential. The E2-effluent was finally ultrafiltered in the pulp mill in order to test the feasibility of ultrafiltration in a real industrial environment. Good membrane for the EP-effluent ultrafiltration based on the EP-screening ex-periments was polyethersulfone membrane UP020 with cut-off value of 20 000 Da. Polysulfone membrane UFX05 with cut-off value of 5 000 Da was promising membrane for the ultrafiltration of the E2-effluent. Based on the concentration filtration of the E2-effluent with UFX05 membrane the water saving potential could be 2.2 m3/Adt for the industrial scale ultrafiltration process. Retention re-sults, such as average COD retention of 60 %, from the trial filtration at the pulp mill with UFX05 membrane were modest compared to the screening experiments, where average COD retention was 75 %. Therefore tighter ultrafiltration mem-branes should be tested for the ultrafiltration of the E2-effluent. The UP020 mem-brane seemed to be suitable for the ultrafiltration of the EP-effluent however con-centration and pilot scale ultrafiltration experiments are needed to verify this.

Separation of lignin in Pulp Mill process and its effect on sodium sulphur balance

The aim of this thesis is to define effects of lignin separation process on Pulp mill chemical balance especially on sodium/sulphur-balance. The objective is to develop a simulation model with WinGEMS Process Simulator and use that model to simulate the chemical balances and process changes. The literature part explains what lignin is and how kraft pulp is produced. It also introduces to the methods that can be used to extract lignin from black liquor stream and how those methods affect the pulping process. In experimental part seven different cases are simulated with the created simulation model. The simulations are based on selected reference mill that produces 500 000 tons of bleached air-dried (90 %) pulp per year. The simulations include the chemical balance calculation and the estimated production increase. Based on the simulations the heat load of the recovery boiler can be reduced and the pulp production increased when lignin is extracted. The simulations showed that decreasing the waste acid stream intake from the chlorine dioxide plant is an effective method to control the sulphidity level when about 10 % of lignin is extracted. With higher lignin removal rates the in-mill sulphuric acid production has been discovered to be a better alternative to the sulphidity control.

Analytics for the modified kraft pulps

Tämän diplomityön tavoitteena on kehittää sopiva analyyttinen menetelmä muokatun kraft-sellukuidun substituutioasteen (DS) kvantitatiivista määrittämistä varten. Muokkauksella tarkoitetaan tässä yhteydessä joko kovalenttisesti tai adsorption avulla tapahtuvaa molekyylin kiinnittymistä sellukuidun pinnalle. Työn kirjallisuusosuudessa käsitellään lyhyesti eri muokkaustapoja ja yhdisteitä joiden avulla voidaan saavuttaa haluttuja ominaisuuksia sellusta valmistetuille lopputuotteille. Lisäksi kirjallisuusosuudessa käydään läpi käyttötarkoitukseen soveltuvimpia suoria ja epäsuoria analyysimenetelmiä. Analyysimenetelmistä kaikkein lupaavimpia testattiin työn kokeellisessa osassa. Diplomityön kokeellisessa osassa keskityttiin kehittämään muokatulle sellulle kvantitatiivista menetelmää DS:n määrittämiseksi Fourier-muunnos infrapuna-vaimennettu kokonaisheijastus (FTIR-ATR) spektrometrillä. Kirjallisuuskatsauksessa ei löytynyt yhtään dokumentoitua tutkimusta, jossa FTIR-ATR menetelmää olisi käytetty muokatun sellukuidun kvantitatiiviseen tutkimukseen. Muiden analyysimenetelmien, kuten alkuaineanalyysin, termogravimetrisen analyysin (TGA) ja valomikroskopian avulla pyrittiin tuottamaan lisätietoa muokkauksesta. Kvantitatiivisen FTIR-ATR menetelmän kehitykseen käytetyt muokatut sellukuidut olivat selluloosa-asetaattia ja selluloosa betainaattia. Saatujen tulosten perusteella muokattujen sulfiitti- ja kraft sellukuitujen DS:n kvantitatiivinen määrittäminen on mahdollista FTIR-ATR menetelmällä. Vähäinen kalibrointipisteiden määrä vaikeutti tarkan analyysimenetelmän tekemistä. Kehitetyn menetelmän suurimpina ongelmina olivat kiinteiden näytteiden heterogeenisyys sekä mahdollisten epäpuhtauksien tunnistaminen. Jatkotutkimusten avulla kehitettyä menetelmää on kuitenkin mahdollista käyttää muokattujen sellukuitujen jatkuvaan analysointiin selluteollisuudessa.

Production and Characterization of Endocylanase from Bacillus Pumilus Using Solidstate Fermentation and its Application in 'Paper Pulp Processing

In the present studies it is clear that Bacillus pumilus xylanase is having the characteristic suited for an industrial enzyme (xylanases that are active and stable at elevated temperatures and alkaline pH are needed). SSF production of xylanases and its application appears to be an innovative technology where the fermented substrate is the enzyme source that is used directly in the bleaching process without a prior downstream processing. The direct use of SSF enzymes in bleaching is a relatively new biobleaching approach. This can certainly benefit the bleaching process to lower the xylanase production costs and improve the economics and viability of the biobleaching technology. The application of enzymes to the bleaching process has been considered as an environmentally friendly approach that can reduce the negative impact on the environment exerted by the use of chlorine-based bleaching agents. It has been demonstrated that pretreatment of kraft pulp with xylanase prior to bleaching (biobleaching) can facilitate subsequent removal of lignin by bleaching chemicals, thereby, reducing the demand for elemental chlorine or improving final paper brightness. Using this xylanase pre-treatment, has resulted in an increased of brightness (8.5 Unit) when compared to non-enzymatic treated bleached pulp prepared using identical conditions. Reduction of the consumption of active chlorine can be achieved which results in a decrease in the toxicity, colour, chloride and absorbable organic halogen (AOX) levels of bleaching effluents. The xylanase treatment improves drainage, strength properties and the fragility of pulps, and also increases the brightness of pulps. This positive result shows that enzyme pre-treatment facilitates the removal of chromophore fragments of pulp there by making the process more environment friendly

Surface properties of eucalyptus pulp fibres as reinforcement of cement-based composites

The objective of the present work is to evaluate the effects of the surface properties of unrefined eucalyptus pulp fibres concerning their performance in cement-based composites. The influence of the fibre surface on the microstructure of fibre-cement composites was evaluated after accelerated ageing cycles, which simulate natural weathering. The surface of unbleached pulp is a thin layer that is rich in cellulose, lignin, hemicelluloses, and extractives. Such a layer acts as a physical and chemical barrier to the penetration of low molecular components of cement. The unbleached fibres are less hydrophilic than the bleached ones. Bleaching removes the amorphous lignin and extractives from the surface and renders it more permeable to liquids. Atomic force microscopy (AFM) helps in understanding the fibre-cement interface. Bleaching improved the fibre- cement interfacial bonding, whereas fibres in the unbleached pulp were less susceptible to the re-precipitation of cement hydration products into the fibre cavities (lumens). Therefore, unbleached fibres can improve the long-term performance of the fibre-cement composite owing to their delayed mineralization.

Hydrogen peroxide and supercritical carbon dioxide: a new bleaching stage for Eucalyptus kraft-O(2) pulps

Kraft pulp is currently bleached largely by the elemental chlorine free (ECF) technology with oxygen, chlorine dioxide, and hydrogen as active agents. This technology brought about significant environmental improvements in relation to standard processes based on chlorine gas and hypochlorite, but there is still need for further improvements. This study presents a novel environmentally friendly bleaching stage - the so-called `hydrogen peroxide in supercritical carbon dioxide`, P((SC-CO2)) - that can be adapted to current ECF bleaching processes, with preference in cases where hydrogen peroxide is already used. In this study, the P((SC-CO2)) stage was evaluated as a replacement to the last peroxide stage of the D(EP)DP bleaching sequence and to the first peroxide stage of the D(EP)DP sequence, for an oxygen delignified eucalypt kraft-O(2) pulp. The P((SC-CO2)) stage was run with 0.5% hydrogen peroxide, at 15% consistency, 70 degrees C, and 73 bar. The reaction time was 30 min. The performances of regular P stages and the new P((SC-CO2)) stage were compared. Promising results were observed with the DEP((SC-CO2))DP sequence; the P((SC-CO2)) decreased kappa number from 2.7 to 2.1, and the hexenuronic acid groups from 17.0 to 12.4 mmol kg(-1). The P((SC-CO2)) stage showed poor performance when applied in the D(EP)DP((SC-CO2)) sequence. It is concluded that the process presents potential but requires further optimization to improve selectivity and efficiency.

Geração de finos no branqueamento de pasta kraft de eucalipto e seu efeito nas propriedades do papel

Este trabalho teve por objetivo avaliar a quantidade de finos gerada por diferentes reagentes de branqueamento e seu efeito nas propriedades físicas e mecânicas da celulose kraft de eucalipto. A polpa foi branqueada por quatro sequências diferentes. Parte das amostras foi classificada em equipamento Bauer-McNett, sendo a parte não classificada (global) refinada para 40 ºSR, em moinho laboratorial PFI. As duas maiores porções de cada amostra proveniente da classificação foram também refinadas com o mesmo número de revoluções que a sua amostra global. Realizaram-se ensaios físicos e mecânicos das amostras refinadas, e suas fibras foram analisadas em equipamento FQA (Fiber Quality Analyser), antes e depois do refino. A maior quantidade de finos foi observada nas polpas refinadas e na sequência-referência. Os resultados de tração foram mais elevados e significativos nas amostras globais; as polpas classificadas não apresentaram diferença entre si, sendo atribuída a maior resistência à tração na presença de finos. A resistência ao rasgo foi afetada pelo comprimento das fibras e não pelo teor de finos. Os maiores valores de ascensão capilar Klemm ocorreram nas amostras classificadas em razão da ausência de finos e do maior comprimento de fibras.

Influência do cancro basal em Eucalyptus grandis nas propriedades da madeira e polpação kraft

The objective of this research is to assess the influences of basal canker on wood properties for the kraft pulp production. The material consisted of seeded E. grandis trees classified into 4 levels of basal canker severity (0, 1, 2 and 3) and installed in three soil types classified by texture (AQ1 and AQ2 - 10 to 15% clay, and LEm2 - 26 to 35 clay). The sampling consisted of randomly selecting five trees for each for each canker severity level and soil type, totaling 60 trees (4 canker levels x 3 soil types x 5 trees). These trees were fallen and cut into sections at 0, 25, 50, 75 and 100% of the commercial height for the collection of disk and logs of wood. The results showed that the soil texture influences in the Eucalyptus canker severity and this fact should be considered when assessing the wood properties and their final destination. The texture of the soil and the severe levels of basal canker influence the wood properties, and therefore the kraft pulping.

Xylanase and β-Xylosidase from Penicillium janczewskii: Production, Physico-Chemical properties, and application of the crude extract to pulp biobleaching

Extracellular xylanase and β-xylosidase production by a Penicillium janczewskii strain were investigated in liquid cultures with xylan from oat spelts under different physical and chemical conditions. The selected conditions for optimized production of xylanase and β-xylosidase were 7 days, pH 6.5, at 30 °C and 8 days, pH 5.0, at 25 °C, respectively. The xylanase exhibited optimal activity in pH 5.0 at 50 °C and the β- xylosidase in pH 4.0 at 75 °C. The xylanase was more stable at pH 6.0 to 9.5, while the β-xylosidase remained stable at pH ranging from 1.6 to 5.5. The xylanase half-life (T50) at 40, 50, and 60 °C was 183, 15, and 3 min, respectively. β-xylosidase half-life was 144, 8, and 4 min at 50, 65, and 75 °C, respectively. When applied to the biobleaching of Eucalyptus kraft pulp, xylanase dosages of 2 and 4 U/g dried pulp reduced, respectively, kappa number by 3.0 and 3.3 units after 1 h treatment, demonstrating that the use of P. janczewskii xylanases in this process is quite promising. The pulp viscosity was not altered, confirming the absence of cellulolytic enzymes in the fungal extract.