Synthesis of liquid menthol by hydrogenation of dementholized peppermint oil over Ni catalysts

Hydrogenation of (-)-menthone and (+)-isomenthone was studied at 2.7 MPa and 100 ºC. The objective was to produce a liquid menthol mixture rich in (-)-menthol from dementholized peppermint oil. Ni-based catalysts were tested and compared for this reaction: a) 6 and 12% Ni dispersed into a nonstoichiometric magnesium aluminate (Ni-Mg-Al) with spinel structure; b) Ni-Raney catalyst. Both types of catalysts were active for (-)-menthone and (+)-isomenthone hydrogenation. Lower conversion but higher selectivity to (-)-menthol was obtained with Ni-Mg-Al catalysts. However, they rapidly lost their activity. Instead Ni-Raney catalysts kept its original activity even after several hydrogenation runs.

NANOPARTICLES OF TUNGSTEN AS LOW-COST MONOMETALLIC CATALYST FOR SELECTIVE HYDROGENATION OF 3-HEXYNE

Low-cost tungsten monometallic catalysts containing variable amounts of metal (4.5, 7.1 and 8.5%W) were prepared by impregnating alumina with ammonium metatungstate as an inexpensive precursor. The catalysts were characterized using ICP, XPS, XRD, TPR and hydrogen chemisorption. These techniques revealed mainly WO3-Al2O3 (W6+) species on the surface. The effects of the content of W nanoparticles and reaction temperature on activity and selectivity for the partial hydrogenation of 3-hexyne, a non-terminal alkyne, were assessed under moderate conditions of temperature and pressure. The monometallic catalysts prepared were found to be active and stereoselective for the production of (Z )-3-hexene, had the following order: 7.1WN/A > 8.5 WN/A ≥ 4.5 WN/A. Additionally, the performance of the synthesized xWN/A catalysts exhibited high sensitivity to temperature variation. In all cases, the maximum 3-hexyne total conversion and selectivity was achieved at 323 K. The performance of the catalysts was considered to be a consequence of two phenomena: a) the electronic effects, related to the high charge of W (+6), causing an intensive dipole moment in the hydrogen molecule (van der Waals forces) and leading to heterolytic bond rupture; the H+ and H- species generated approach a 3-hexyne adsorbate molecule and cause heterolytic rupture of the C≡C bond into C- = C+; and b) steric effects related to the high concentration of WO3 on 8.5WN/A that block the Al2O3 support. Catalyst deactivation was detected, starting at about 50 min of reaction time. Electrodeficient W6+ species are responsible for the formation of green oil at the surface level, blocking pores and active sites of the catalyst, particularly at low reaction temperatures (293 and 303 K). The resulting best catalyst, 7.1WN/A, has low fabrication cost and high selectivity for (Z )-3-hexene (94%) at 323 K. This selectivity is comparable to that of the classical and more expensive industrial Lindlar catalyst (5 wt% Pd). The alumina supported tungsten catalysts are low-cost potential replacements for the Lindlar industrial catalyst. These catalysts could also be used for preparing bimetallic W-Pd catalysts for selective hydrogenation of terminal and non-terminal alkynes.

Electrochemical properties of Cu4[PhN3C6H4N3(H)Ph]4(µ-O)2, a tetranuclear Copper(II) complex with 1-phenyltriazenido-2-phenyltriazene-benzene as ligand

Bis-(µ2-oxo)-tetrakis{[1-feniltriazene-1,3-diil)-2-(phenyltriazenil)benzene copper(II) is a tetranuclear complex which shows four Cu(II) ions coordinated by four 1,2-bis(phenyltriazene)benzene bridged ligands, with one diazoaminic deprotonated chain, and two O2- ligands. The complex reduces at E1/2 = -0.95 V vs Fc+/Fc, a two electrons process. Cyclic voltammetric and spectroelectrochemical studies showed a reversible process. When immobilized on carbon paste electrode, the complex electrocatalyses the reduction of O2 dissolved on aqueous solution at -0.3 V vs SCE potential. The obtained current shows linearity with O2 concentration.

Molecular modeling of asymmetric induction in heterogeneously catalyzed hydrogenation of the C=O bond

Modifiering av metallytor med starkt adsorberade kirala organiska molekyler är eventuellt den mest relevanta teknik man vet i dag för att skapa kirala ytor. Den kan utnyttjas i katalytisk produktion av enantiomeriskt rena kirala föreningar som behövs t.ex. som läkemedel och aromkemikalier. Trots många fördelar av asymmetrisk heterogen katalys jämfört med andra sätt för att få kirala föreningar, har den ändå inte blivit ett allmänt verktyg för storskaliga tillämpningar. Detta beror t.ex. på brist på djupare kunskaper i katalytiska reaktionsmekanismer och ursprunget för asymmetrisk induktion. I denna studie användes molekylmodelleringstekniker för att studera asymmetriska, heterogena katalytiska system, speciellt hydrering av prokirala karbonylföreningar till motsvarande kirala alkoholer på cinchona-alkaloidmodifierade Pt-katalysatorer. 1-Fenyl-1,2-propandion (PPD) och några andra föreningar, som innehåller en prokiral C=O-grupp, användes som reaktanter. Konformationer av reaktanter och cinchona-alkaloider (som kallas modifierare) samt vätebundna 1:1-komplex mellan dem studerades i gas- och lösningsfas med metoder som baserar sig på vågfunktionsteori och täthetsfunktionalteori (DFT). För beräkningen av protonaffiniteter användes också högst noggranna kombinationsmetoder såsom G2(MP2). Den relativa populationen av modifierarnas konformationer varierade som funktion av modifieraren, dess protonering och lösningsmedlet. Flera reaktant–modifierareinteraktionsgeometrier beaktades. Slutsatserna på riktning av stereoselektivitet baserade sig på den relativa termodynamiska stabiliteten av de diastereomeriska reaktant–modifierare-komplexen samt energierna hos π- och π*-orbitalerna i den reaktiva karbonylgruppen. Adsorption och reaktioner på Pt(111)-ytan betraktades med DFT. Regioselektivitet i hydreringen av PPD och 2,3-hexandion kunde förklaras med molekyl–yta-interaktioner. Storleken och formen av klustret använt för att beskriva Pt-ytan inverkade inte bara på adsorptionsenergierna utan också på de relativa stabiliteterna av olika adsorptionsstrukturer av en molekyl. Populationerna av modifierarnas konformationer i gas- och lösningsfas korrelerade inte med populationerna på Pt-ytan eller med enantioselektiviteten i hydreringen av PPD på Pt–cinchona-katalysatorer. Vissa modifierares konformationer och reaktant–modifierare-interaktionsgeometrier var stabila bara på metallytan. Teoretiskt beräknade potentialenergiprofiler för hydrering av kirala α-hydroxiketoner på Pt implicerade preferens för parvis additionsmekanism för väte och selektiviteter i harmoni med experimenten. De uppnådda resultaten ökar uppfattningen om kirala heterogena katalytiska system och kunde därför utnyttjas i utvecklingen av nya, mera aktiva och selektiva kirala katalysatorer.

Hydrogenation of L-arabinose, D-galactose, D-maltose and L-rhamnose

Under de senaste åren har intresset för utnyttjandet av förnybara resurser kraftigt ökat. I samband med detta utgör kolhydrater en viktig del av den tillgängliga förnybara biomassan och den har därefter blivit föremål för ett stort intresse inom hållbar kemi. Sockeralkoholer är en särskilt viktig grupp av molekyler som vanligtvis erhålls ur kolhydrater och som har mångsidiga tillämpningar som t.ex. lågkalorihaltiga sötningsmedel. Forskningen i doktorsarbetet omfattar hydreringen av naturligt förekommande sockerarter L-arabinos, D-galaktos, D-maltos och L-ramnos till respektive sockeralkoholer. Dessa sockeralkoholer kan användas bl.a. som hälsosamma sötningsmedel på samma sätt som xylitol. Grunden för detta arbete består av hydreringsexperiment som utfördes på en dispergerad ruteniumkatalysator i syfte att studera bildningskinetiken av de motsvarande sockeralkoholerna. Reaktionerna genomfördes vid temperaturer mellan 90 och 130 °C och vätetryck mellan 40 och 60 bar. Under dessa betingelser var det möjligt att åstadkomma sockeromvandlingar upp till 100 %. Reaktionshastigheterna modellerades matematiskt. Konkurrerande kinetiska modeller som baserades på Langmuir-Hinshelwood-konceptet föreslogs för att beskriva reaktionerna. Parametrar i hastighetsekvationerna bestämdes därefter genom icke-linjär regression. Dessa modeller kunde väl förutsäga hydreringsreaktionernas förlopp och de kan följaktligen användas för design av industriella anläggningar. Ytterligare hydreringsexperiment med sockerblandningar genomfördes för att fördjupa kunskaper i kinetik och reaktionsmekanismer av sockerhydreringen. Studierna genomfördes med syntetiska sockerblandningar av L-arabinos och D-galaktos (de viktigaste komponenterna i hemicellulosan arabinogalaktan). Fullständig omsättning uppnåddes med utmärkta selektiviteter som överskred 95 % och dessutom inverkade varken temperatur eller vätetryck på reaktionens förlopp på något oväntat sätt. Antagandet av konkurrerande adsorption för en samtidig reduktion av båda sockermolekylerna gav en kinetisk modell som noggrant beskrev de experimentella resultaten. Idén om att utforska potentiella sätt att påskynda bildningen av sockeralkoholer ledde till utföringen av hydreringsexperiment med L-arabinos och D-galaktos i närvaro av ultraljud. Det visade sig att ultraljudets inverkan var oberoende av sockerhalten och vätetrycket och att bestrålningen gynnade hydreringen av D-galaktos trots att den inte förhindrade Ru/C-katalysatorns deaktivering överhuvudtaget. En kinetisk modell som beaktade deaktiveringen utvecklades. Kontinuerlig hydrering av L-arabinos genomfördes med tre olika Ru-katalysatorer på tre olika bärare: tyg av aktivt kol, kolnanorör på svampliknande metalliska strukturer samt krossade partiklar av en kommersiell Ru/C-katalysator. Det visade sig att det var möjligt att omvandla L-arabinos till arabitol med höga selektiviteter med hjälp av Ru/koltyg-katalysatorn. Dessa experiment demonstrerade att hydreringen av de valda sockerarterna är en helt genomförbar rutt till framställning av fin- och specialkemikalier, som kan förverkligas i större skala.

Asymmetric hydrogenation of alkenes with cationic iridium(I) complexes of 2-phosphino-1-aminoferrocene ligands

Iridium complexes with bidentate P,N ligands represent a class of catalysts that significantly expand the application range of asymmetric hydrogenation. New substrate classes, for which there have previously been no suitable catalysts, can now be efficiently hydrogenated in high conversion and enantioselectivity. These substrates are often of synthetic importance, thus iridium catalysis represents a significant advance in the field of asymmetric catalysis. Planar chiral ferrocenyl aminophosphine ligands in which both heteroatoms were directly bound to the cyclopentadienyl ring were prepared by BF3-activated lithiationsubstitution in the presence of a chiral diamine in 49-59% yield and 75-85% enantiomeric excess. Some of these ligands were recrystallized to enantiomeric purity via ammonium fluoroborate salt formation of the phosphine sulfide. A crystal structure of one of these compounds was obtained and features an intramolecular hydrogen bond between the nitrogen, hydrogen, and sulfur atoms. Neutralization, followed by desulfurization, provided the free ligands in enantiomeric purity. Iridium complexes with these ligands were formed via reaction with [Ir(COD)Clh followed by anion exchange with NaBArF. These complexes were successfully applied in homogeneous hydrogenation of several prochiral substrates, providing products in up to 92% enantiomeric excess. Variation of the dimethyl amino group to a pyrrolidine group had a negative effect on the selectivity of hydrogenation. Variation of the substituents on phosphorus to bulkier ortho-tolyl groups had a positive effect, while variation to the more electron rich dicyclohexyl phosphine had a negative effect on selectivity.

Half-sandwich Complexes of Ruthenium; Synthesis and Application to Catalysis

This thesis describes syntheses and catalytic reactivity of several half-sandwich complexes of ruthenium. The neutral ruthenium trihydride complex, Cp(PPri3)RuH3(1), can efficiently catalyse the H/D exchange reaction between various organic substrates and deuterium sources, such as benzene-d6. Moreover, the H/D exchange reactions of polar substrates were also observed in D2O, which is the most attractive deuterium source due to its low cost and low toxicity. Importantly, the H/D exchange under catalytic conditions was achieved not only in aromatic compounds but also in substituted liphatic compounds. Interestingly, in the case of alkanes and alkyl chains, highly selective deuterium incorporation in the terminal methyl positions was observed. It was discovered that the methylene units are engaged in exchange only if the molecule contains a donating functional group, such as O-and N-donors, C=C double bonds, arenes and CH3. The cationic half-sandwich ruthenium complex [Cp(PPri3)Ru(CH3CN)2]+(2) catalyses the chemoselective mono-addition of HSiMe2Ph to pyridine derivatives to selectively give the 1,4-regiospecific, N-silylated products. An ionic hydrosilylation mechanismis suggested based on the experiments. To support this mechanistic proposal, kinetic studies under catalytic conditions were performed. Also, the 1,4-regioselective mono-hydrosilylation of nitrogen containing compounds such as phenanthroline, quinoline and acridine can be achieved with the related Cp*complex [Cp*(phen)Ru(CH3CN)]+(3) (phen = 1,10-phenanthroline) and HSiMe2Ph under mild conditions. The cationic ruthenium complex 2 can also be used as an efficient catalyst for transfer hydrogenation of various organic substrates including carbonyls, imines, nitriles and esters. Secondary alcohols, amines, N-isopropylidene amines and ether compounds can be obtained in moderate to high yields. In addition, other ruthenium complexes, 1,3 and [Cp*(PPri3)Ru(CH3CN)2]+(4), can catalyse transfer hydrogenation of carbonyls although the reactions were sluggish compared to the ones of 2. The possible intermediate, Cp(PPri3)Ru(CH3CN)(H), was characterized by NMR at low temperature and the kinetic studies for the transfer hydrogenation of acetophenone were performed. Recently, chemoselective reduction of acid chlorides to aldehydes catalysed by the complex 2 was reported. To extend the catalytic reactivity of 2, reduction of iminoyl chlorides, which can be readily obtained from secondary amides, to the corresponding imines and aldehydes was investigated. Various substituted iminoyl chlorides were converted into the imines and aldehydes under mild conditions and several products were isolated with moderate yields.

Diastereoselective Synthesis of Planar Chiral N-Substituted Ferrocenes Derived from Epimeric Imidazolones and their Application to Asymmetric Hydrogenation of Quinolines

This thesis describes the synthesis and use of an N-substituted ferrocene bearing a proline-derived chiral directing group and diastereoselective lithiation-electrophile quench of the pro-Sp hydrogen of the ferrocene to give planar chiral products in >95:5 dr. The auxiliary group is found to be stable to lithium bases of types RLi and R2NLi giving the same diastereoselectivity. The anti- epimer of the previously mentioned syn auxiliary induces lithiation of pro Rp rather than pro Sp hydrogen in >95:5 dr. Upon electrophile quench and elimination, the enantiomer of the syn-derived planar chiral imidazolone is obtained. Hence, this method provides a practical way to prepare planar chiral enantiomers in this series without the use of a more expensive D-proline derived starting material. The syn and anti epimers have β, γ-stereogenic centers and the origin of stereoselectivity in lithiation appears to be driven by the conformational bias exerted by the β-silyloxy moiety in each chiral auxiliary. In the thesis, this conclusion is supported using insensitivity of lithiation selectivity to the bulkiness of the base, comparison of enantiomers, deuteration experiments, nOe difference studies and computational modeling of the ground states and lithiation transition states for both substrates. The products are then converted to ligand precursors to make iridium and rhodium complexes. Among them, one of the cationic iridium complex is found to be effective in the asymmetric hydrogenation of 2-substituted quinolines with enantioselectivities up to 80% at pressures as low as 5 atm.

Alkylation of Benzene with I-Octene over Titania Pillared Monmorillonite

Linear alkylbenzene sulfonic acid, the largest-volume synthetic surfactant, in addition to its excellent performance , is important due to its biodegradable environmental friendliness, as it has a straight chain and is prepared by the sulphonation of linear alkylbenzenes (LAB). To ensure environmental protection, the commercial benzene alkylation catalysts HF or AICI3 are replaced and we have developed a clean LAB production process using a pillared clay catalyst capable of not only replacing the conventional homogeneous catalyst, but also having high selectivity for the best biodegradable 2-phenyl LAB isomer .Pillared clay catalysts having high Bronsted acidity show efficient conversion in gas phase alkylation of benzene with 1-octene with a good 2-phenyl octane selectivity.

Thermochemistry of Charge-Transfer Complexes of 7,7,8,8-Tetracyanoquinodimethane with Benzene and Its Chloro Derivatives

The enthalpies of formation of charge-transfer complexes of benzene, chlorobenzene, and 1,3-dichlorobenzene as donors with 7,7,8,8-tetracyanoquinodimethane as acceptor were determined. The thermochemical data show an increased stability of charge-transfer complexes of donors with permanent dipole moment. The results confirm the importance of electrostatic forces in bonding and stabilizing weak complexes. The approximate formation constants of the complexes are also reported.

Influence of residual cations (Na+, K+ and Mg2+) in the alkylation activity of benzene with 1-octene over rare earth metal ion exchanged FAU–Y zeolite

The effect of residual cations in rare earth metal modified faujasite–Y zeolite has been monitored using magic angle spinning NMR spectral analysis and catalytic activity studies. The second metal ions being used are Na+, K+ and Mg+. From a comparison of the spectra of different samples, it is concluded that potassium and magnesium exchange causes a greater downfield shift in the 29Si NMR peaks. Also, lanthanum exchanged samples show migration behavior from large cages to small cages, which causes the redistribution of second counter cations. It is also observed that Mg2+ causes the most effective migration of lanthanum ions due to its greater charge. The prepared systems were effectively employed for the alkylation of benzene with 1-octene in the vapor phase. From the deactivation studies it is observed that the as-exchanged zeolites possess better stability towards reaction condition over the pure HFAU zeolite.

Alkylation of Benzene with higher olefins over zeolites: A green route for lab synthesis.

The objective of the present work is to improve the textural and structural properties of zeolite-Y through ion exchange with rare earth metals. We meant to obtain a comparative evaluation of the physicochemical properties and catalytic activity of rare earth modified H-Y, Na-Y, K-Y, and Mg-Y zeolites. Friedel-Crafts alkylations of benzene with higher 1- olefins such as 1-octene, 1-decene, and 1dodecene for the synthesis of linear alkylbenzene (LAB) have been selected for the present study. An attempt has also been directed towards the correlation of the enhancement in 2-phenylalkane formation to the improvement in the textural and structural properties upon rare earth modification for the zeolite-Y. The present method for LAB synthesis stands as an effective Green alternative for the existing hydrofluoric acid technology

Automatic generation of active coordinates for quantum dynamics calculations: application to the dynamics of benzene photochemistry

A new practical method to generate a subspace of active coordinates for quantum dynamics calculations is presented. These reduced coordinates are obtained as the normal modes of an analytical quadratic representation of the energy difference between excited and ground states within the complete active space self-consistent field method. At the Franck-Condon point, the largest negative eigenvalues of this Hessian correspond to the photoactive modes: those that reduce the energy difference and lead to the conical intersection; eigenvalues close to 0 correspond to bath modes, while modes with large positive eigenvalues are photoinactive vibrations, which increase the energy difference. The efficacy of quantum dynamics run in the subspace of the photoactive modes is illustrated with the photochemistry of benzene, where theoretical simulations are designed to assist optimal control experiments

New Ruthenium complexes containing N, P and S-donor type of ligands: coordination chemistry, characterization and application to asymetric and non-asymetric catalysis

Síntesi de nous complexos de Ruteni amb lligands no quirals que tenen per fórmula [Ru(phen)([9]aneS3)X] (on X = H2O, py i MeCN). Caracterització espectroscòpica electroquímica i estructural d'aquesta família de complexos. Estudi de les seves propietats catalítiques en front a l'oxidació de substrats orgànics com l'alcohol benzílic en reaccions d'electrocatàlisi. Avaluació cinètica dels mecanismes de substitució entre els complexos Ru-py i Ru-MeCN. Generació d'un interruptor molecular foto-induït. Síntesi de nous complexos quirals de Ru atropoisomèricament purs amb lligands oxazolínics que tenen per fórmula [Ru(trpy)(Ph-box-R)X] on (X = Cl, H2O, py, MeCN, 2-OH-py). Caracterització estructural exhaustiva en estat sòlid (Raig-X) en solució (RMN) i en fase gas (càlculs DFT). Avaluació de la seva activitat catalítica en reaccions asimmetriques d'epoxidació de substrats proquirals. Síntesi de nous lligands polipiridílics quirals amb simetria C3. Estudi de la seva química de coordinació i avaluació de la seva activitat catalítica en reaccions asimmetriques d'oxidació i reducció.