Gulistān : manuscript, 1727?

Written in one column (in black and red ink) and two columns (in red ink), 29 lines per page.

London-van der Waals adhesiveness of rough particles

Van der Waals forces often dominate interactions and adhesion between fine particles and, in turn, decisively influence the bulk behaviour of powders. However, so far there is no effective means to characterize the adhesive behaviour of such particles. A complication is that most powder particles have rough surfaces, and it is the asperities on the surfaces that touch, confounding the actual surface that is in contact. Conventional approaches using surface energy provide limited information regarding adhesion, and pull-off forces measured through atomic force microscope (AFM) are highly variable and difficult to interpret. In this paper we develop a model which combines the Rumpf-Rabinovich and the JKR-DMT theories to account simultaneously for the effects of surface roughness and deformation on adhesion. This is applied to a 'characteristic asperity' which may be easily obtained from AFM measurements. The concept of adhesiveness, a material property reflecting the influences of elastic deformability, surface roughness, and interfacial surface energy, is introduced as an efficient and quantitative measure of the adhering tendency of a powder. Furthermore, a novel concept of specific adhesiveness is proposed as a convenient tool for characterizing and benchmarking solid materials. This paper provides an example to illustrate the use of the proposed theories. (c) 2005 Elsevier B.V. All rights reserved.

Influence of pretreatment on corrosion behaviour of duplex zinc/polymer coatings on steel substrates

An investigation has been undertaken to determine the major factors influencing the corrosion resistance of duplex-zinc coatings on steel substrates.Premature failure of these systems has been attributed to the presence of defects such as craters and pinholes in the polymer film and debonding of the polymer film from the zinc substrate.Defects found on commercially produced samples have been carefully characterised using metallographic and scanning electron microscopy techniques. The influence of zinc substrate surface roughness, polymer film thickness and degassing of conversion coatings films on the incidence of defects has been determined.Pretreatments of the chromate, chromate-phosphate, non chromate, and alkali-oxide types were applied and the conversion coatings produced characterised with respect to their nature and composition. The effect of degassing on the properties of the films was also investigated. Electrochemical investigations were carried out to determine the effect of the presence of the eta or zeta phase as the outermost layer of the galvanized coating.Flow characteristics of polyester on zinc electroplated hot-dip continuous and batch galvanized and zinc sprayed samples were investigated using hot-stage microscopy. The effects of different pretreatments and degassing after conversion coating formation on flow characteristics were determined.Duplex coatings were subjected to the acetic acid salt spray test. The effect on adhesion was determined using an indentation debonding test and the results compared with those obtained using cross-cut/peel and pull-off tests. The locus of failure was determined using scanning electron microscopy and X-ray photoelectron spectroscopy techniques.

Développement d’une stratégie de modification du bois afin de limiter les variations dimensionnelles du produit lambris dans un contexte éco-responsable

Ce travail de thèse présente deux grands axes. Le premier axe, touche les traitements du bois dans le but principal de réduire les variations dimensionnelles et d’améliorer la résistance à l’attaque des champignons lignivores. Le second axe quant à lui, touche l’aspect environnemental du traitement acide citrique-glycérol. Ce dernier a pour but principal de démontrer que le prolongement de la durée de vie en service du produit lambris traité, compense les impacts environnementaux causés par ce traitement. Dans le premier axe, deux traitements ont été réalisés sur deux essences de pin (Pinus strobus L. et Pinus contorta D.). Un traitement à l’anhydride maléique et un autre traitement avec une solution d’acide citrique – glycérol brute (AC-G). Dans le premier cas, les effets de deux paramètres (la durée de séchage et la température d’estérification) sur les résultats des essais de stabilité dimensionnelle, de résistance à la dégradation fongique et de vieillissement accéléré ont été évalués. Trois niveaux de durée de séchage après imprégnation (12 h, 18 h et 24 h) et trois niveaux de température d’estérification (140 °C, 160 °C et 180 °C) ont été considérés. Dans le second cas, après identification du meilleur catalyseur (HCl) et du meilleur ratio acide citrique – glycérol (3/1) pendant les essais préliminaires, les performances de ce traitement sur la stabilité dimensionnelle, la résistance à la pourriture fongique, la dureté de surface et l’adhérence des couches de revêtement de peinture sur la surface du substrat bois ont été analysées. Les résultats obtenus ont été appuyés par une suite d’analyses qualitatives et quantitatives pour mieux comprendre et expliquer. Les analyses qualitatives sont : (i) la spectroscopie infrarouge à transformée de Fourier (IRTF) et (ii) la microscopie électronique à balayage (MEB) tandis que la quantitative, l’analyse par perte de masse a été faite par pesée. Dans le second axe, une analyse des impacts environnementaux du traitement AC-G a été effectuée par le biais du logiciel SimaPro v8. La base de données Ecoinvent v3 et la méthode d’analyse d’impact Impact 2002+ ont été utilisées dans cette partie du travail de thèse. Sur la base des résultats du second traitement (AC-G) et des travaux disponibles dans la littérature, nous avons estimé, une durée de vie en service des lambris traités. Les différents scénarios de la durée de vie du lambris traité mis sur pied par rapport à celle offerte aujourd’hui par l’industrie, nous permettent de modéliser les impacts environnementaux du traitement. A cette fin, l’analyse de cycle de vie (ACV) a été utilisée comme outil de conception. En conclusion, les paramètres, durée de séchage et température d’estérification influencent les résultats obtenus dans le cas du traitement du bois à l’anhydride maléique. La combinaison 24 h de séchage et 180 °C, température d’estérification, représente les paramètres qui offrent les meilleurs résultats de stabilité dimensionnelle, de résistance à la dégradation fongique et de vieillissement accéléré. Le traitement AC-G améliore la stabilité dimensionnelle, la résistance à la dégradation fongique et la dureté de surface des échantillons. Cependant, le traitement réduit l’adhérence des couches de peinture. Les impacts environnementaux produits par le traitement AC-G sont majoritairement liés à la consommation de la ressource énergie (électricité). Le traitement prolonge la durée de vie en service du lambris traité et il a été mis en évidence que le scénario de durée de vie qui permettrait que le lambris traité puisse se présenter comme un produit à faible impact environnemental par rapport au lambris non traité est celui d’une durée de vie de 55 ans.

Effets des procédés d’usinage de finition sur les propriétés de surface, la performance d’un vernis et l’émission de poussières du bois de chêne rouge

La performance d’un produit de finition sur le bois est influencée par la manière dont la surface est préparée. Le ponçage est très utilisé pour préparer les surfaces lors de la finition. Toutefois, ce procédé génère une grande quantité de poussières. Ainsi, les effets des procédés d’usinage sur les propriétés de surface, la performance d’un vernis et l’émission de poussières ont été étudiés dans le but de déterminer les modes de préparation des surfaces les plus adéquats pour le bois de chêne rouge. Dans un premier volet, les propriétés de surface et la performance d’un vernis ont été évaluées sur les surfaces préparées à l’aide du procédé traditionnel de ponçage et de trois procédés alternatifs de rabotage soit la coupe périphérique droite, la coupe hélicoïdale et la coupe oblique. La qualité de surface a été évaluée au moyen des caractéristiques de rugosité, d’endommagement cellulaire et de mouillabilité. Des essais de résistance à l’adhésion d’un vernis d’usage intérieur ont été effectués avant et après un traitement de vieillissement accéléré. Les résultats ont montré que le ponçage a induit une rugosité et un niveau de fibrillation supérieurs à ceux des autres procédés, ainsi qu’une mouillabilité et une adhésion du vernis après vieillissement accéléré élevées. Les surfaces rabotées avec la coupe périphérique droite ont présenté un certain niveau de fibrillation, une rugosité et une mouillabilité intermédiaires. Néanmoins, l’adhésion du vernis après vieillissement a été également inférieure par rapport aux autres procédés. La coupe hélicoïdale a produit une rugosité intermédiaire. D’autre part, la coupe oblique a été le procédé qui a présenté une perte d’adhésion après vieillissement similaire au ponçage. Ce procédé a généré des surfaces lisses avec rugosité et mouillabilité intermédiaires. Sur la base des résultats obtenus, le ponçage à l’aide d’un programme P100-grain et une vitesse d’avance de 7 m/min, la coupe périphérique droite avec un angle d’attaque de 25° et une onde d’usinage de 1,0 mm, la coupe hélicoïdale avec une onde d’usinage de 1,0 mm et la coupe oblique realisé avec un angle oblique de 15° ont permis d’obtenir les meilleures conditions d’usinage pour chaque procédé. Dans un deuxième volet, l’effet de différents paramètres de coupe sur l’émission de poussières et la rugosité de la surface a été étudié lors de la coupe hélicoïdale. Les émissions de poussières ont diminué avec la diminution de laprofondeur de coupe et l’augmentation de l’épaisseur moyenne du copeau. Cependant, les surfaces obtenues avec l’épaisseur moyenne du copeau plus élevée ont présenté une rugosité supérieure. Par contre, si une surface plus lisse est requise, une vitesse d’avance intermédiaire doit être utilisée afin de diminuer la rugosité des surfaces sans exposer les travailleurs à des niveaux élevés de poussière de bois. Par ailleurs, l’émission de poussières pour chaque fraction de particules peut être estimée à travers les modèles développés.

Anomaly diagnosis in ceramic claddings by thermography - A review

With the increasing importance given to building rehabilitation comes the need to create simple, fast and non-destructive testing methods (NDT) to identify problems and for anomaly diagnosis. Ceramic tiles are one of the most typical kinds of exterior wall cladding in several countries; the earliest known examples are Egyptian dating from 4000 BC. This type of building facade coating, though being quite often used in due to its aesthetic and architectural characteristics, is one of the most complex that can be applied given the several parts from which it is composed; hence, it is also one of the most difficult to correctly diagnose with expeditious methods. The detachment of ceramic wall tiles is probably the most common and difficult to identify anomaly associated with this kind of cladding and it is also definitely the one that can compromise security the most. Thus, it is necessary to study a process of inspection more efficient and economic than the currently used which often consist in semi-destructive methods (the most common is the pull off test), that can only be used in a small part of the building at a time, allowing some assumptions of what can the rest of the cladding be like. Infrared thermography (IRT) is a NDT with a wide variety of applications in building inspection that is becoming commonly used to identify anomalies related with thermal variations in the inspected surfaces. Few authors have studied the application of IRT in anomalies associated with ceramic claddings claiming that the presence of air or water beneath the superficial layer will influence the heat transfer in a way that can be detected in both a qualitative and a quantitative way by the thermal camera, providing information about the state of the wall in a much broad area per trial than other methods commonly used nowadays. This article intends to present a review of the state of art of this NDT and its potentiality in becoming a more efficient way to diagnose anomalies in ceramic wall claddings.

Resistance of an epoxy coating with an organic inhibitor to cathodic disbondment in sea water

In this study, the effect of anti-corrosion inhibitor addition to epoxy coating, on the disbanding rate was evaluated. First to determination of mechanism, the bare steel substrates were immersed in the 3.5% NaCl solution and the solution containing 1 mM anti corrosion. The Electrochemical Impedance Spectroscopy was performed after 5 and 24 hour. The results indicated a lower corrosion rate in the presence of inhibitor. During the time, charge transfer resistance, was decreased for the substrates immersed in NaCl solution, and increased for the substrates immersed in NaCl solution containing 1 mM anti corrosion. This result can be related to more stability of corrosion products in presence of anti-corrosion and film formation. The coated substrates, with four different concentration of anticorrosion in coating, were protected under -1.2 voltage in the 3.5% NaCl solution. After 12 and 24 hour, the EIS test and disbanding area measurement, were evaluate. The lower disbanding rate, more charge transfer resistance and less double layer capacitance for the coating containing 0.75w% inhibitor, were observed. The result of Pull-off test after 1 day immersion in 3.5% NaCl solution, showed more wet adhesion for the coating containing 0.75w% inhibitor. The images of FE-SEM electron microscope and surface analyses EDX on the coated substrate after disbanding and the bare substrate immersed in 3.5w% NaCl containing 1 mM inhibitor, were proved the formation of stabilized film.

Estudo das principais argamassas utilizadas na reabilitação de edifícios antigos

Com o passar dos anos, as obras mais sublimes, começam a mostrar marcas subtis ou profundas de deterioração, como por exemplo: fissurações e defeitos associados à humidade. Estes são reflexo de fatores externos, como fungos, a própria atmosfera reativa, mudanças climatéricas e, até mesmo, a ação do homem. Neste seguimento pretende-se estudar as principais argamassas utilizadas na reabilitação de edifícios antigos, principalmente, as argamassas utilizadas no decorrer das obras ao longo do estágio, com o objetivo de comparar as suas caraterísticas, sendo estas argamassas tradicionais e pré-fabricadas. Foram feitos vários ensaios para determinar as suas resistências mecânicas, nomeadamente, o ensaio de resistência à flexão e compressão em diferentes idades após a confeção das argamassas, e ensaios para determinar a sua durabilidade como o ensaio de absorção da água por capilaridade; ensaio de absorção de água por imersão às 48horas (pressão atmosférica); ensaio para determinação do teor de água às 48horas e o ensaio de arrancamento (pull-off). A análise dos resultados mostrou que as argamassas adquirem mais resistência com o passar do tempo após a sua confeção, e que as argamassas dos provetes obtidos de forma tradicional, constituídos por argamassa de cal Hidráulica (HL5) e argamassa de cimento, apresentam melhores resultados do que a argamassa pré-fabricada (weber.cal classic).

Avaliação de concretos reforçados por confinamento com manta de fibra de vidro estrutural e pré-impreganada

Due to the occurrence of diseases in the use of structural reinforcements in composites, with presentation of concrete blanket detachment, has been identified the need to evaluate the performance of concrete reinforced with glass fiber. This study aims to evaluate these concretes by means of testing methodologies, using concrete with low resistance with structural reinforcement for confinement by preimpregnated glass fiber and traditional fiberglass blanket. The first stage of work was the development of methodologies for analysis, opting for four types, such as the acoustic survey, strength to compressive, the pull-off and ultrasound. Next, tests were carried out using the four selected methodologies in 30 of proof-of-specimens by 5x10 cm, 15 were reinforced with the traditional fiberglass blanket with 5specimens exposed to test a marine environment of marine coastline of Natal-RN and 15 were reinforced with a pre-impregnated glass fiber blanket, as well as 5specimens exposed to a test environment of the marine coastline of Natal-RN. After conducting the acoustic survey, it has been verified a lack of delaminating and air bubbles in the samples, confirming the absence of gross shortcomings in the implementation of the ribs both the traditional fiberglass blanket and in the preimpregnated fiber glass blanket. After carrying out methods of pull-off and compressive strengthening test it was observed that the reinforced proof-bodies with pre-impregnated glass blanket showed maximum stresses higher than the traditional fiberglass blanket; consequently a greater grip with the formation of a smaller area of . fracture, unlike traditional glass mat, which showed lower maximum stresses, with a greater area of fracture. It was also found that the traditional fiberglass blanket presented detachment of blanket-concrete interface, unlike the pre-impregnated fiberglass blanket, which showed a better grip on the blanket-concrete interface. In the trial of ultrasound there was no presence of cracks in the blanket-concrete interface, yielding to both blankets good compactness of the concrete. At the end of this work, they were developed and proposed two methods of testing for evaluation of reinforced concrete structures with composites, for standardization, the acoustic survey and pull-off

A switching control strategy for single and dual inductor push-pull converters

A switching control strategy is proposed for single and dual inductor current-fed push-pull converters. The proposed switching control strategy can be used with both current-fed push-pull converters with an active voltage doubler rectifier, or active rectifier, in the secondary side of the isolation transformer. The proposed switching control strategy makes turn-on and turn-off processes of the primary side power switches zero-voltage-switching and zero-current-switching respectively. The soft-switching operation of the single and dual inductor push-pull converters, with both types of active rectifier, is explained. Simulation and experimental results are provided to validate soft switching operation of the current-fed push-pull converters with the proposed switching control strategy.

Soft-switching single inductor current-fed push-pull converter for PV applications

A switching control strategy is proposed for single inductor current-fed push-pull converter with a secondary side active voltage doubler rectifier or a voltage rectifier used in photovoltaic (PV) grid interfacing. The proposed switching control strategy helps to turn-on and turn-off the primary side power switches with zero-voltage and zero-current switching. The operation of the push-pull converter is analyzed for two modes of operation. The feasibility of the proposed switching control strategy is validated using simulation and experimental results.

Simulations of X and Y Retinal Ganglion Cell Behavior with a Nonlinear Push-pull Model of Spatiotemporal Retinal Processing

This article describes a nonlinear model of neural processing in the vertebrate retina, comprising model photoreceptors, model push-pull bipolar cells, and model ganglion cells. Previous analyses and simulations have shown that with a choice of parameters that mimics beta cells, the model exhibits X-like linear spatial summation (null response to contrast-reversed gratings) in spite of photoreceptor nonlinearities; on the other hand, a choice of parameters that mimics alpha cells leads to Y-like frequency doubling. This article extends the previous work by showing that the model can replicate qualitatively many of the original findings on X and Y cells with a fixed choice of parameters. The results generally support the hypothesis that X and Y cells can be seen as functional variants of a single neural circuit. The model also suggests that both depolarizing and hyperpolarizing bipolar cells converge onto both ON and OFF ganglion cell types. The push-pull connectivity enables ganglion cells to remain sensitive to deviations about the mean output level of nonlinear photoreceptors. These and other properties of the push-pull model are discussed in the general context of retinal processing of spatiotemporal luminance patterns.

Pull-out behaviour of axially loaded basalt fibre reinforced polymer (BFRP) rods bonded parallel to the grain of glulam elements

Synopsis: Bonded-in rod timber joints off er several advantages over conventional types of joint, including high local force transfer, very stiff connections, and improved ?re and aesthetic properties since the connection is completely hidden in the insulating timber members. More recently, the use of ?bre reinforced polymer (FRP) as a connecting rod, alternative to steel rods, in bonded-in rod connections for timber structures has been investigated. However, the investigation into the behaviour of such joints is limited, in particular, connections involving basalt ?bre reinforced polymers (BFRP) bars - which is the primary focus of this research. This paper presents an experimental programme conducted to investigate the behaviour of bonded-in BFRP bars loaded parallel to the grain of glulam members. Tensile pull-out tests were conducted to examine the effect of bonded length and bond stress-slip on the structural capacity of the connection. An analytical design expression for predicting pull-out capacity is proposed and the results have been compared with some established design equations. It was found that pull-out load increased approximately linearly with the bonded length, up to maximum which occurred at a bonded length of 15 times the hole diameter, and did not increase beyond this bonded length. The most signi?cant failure modes were failure at the timber/adhesive interface followed by pullout of the BFRP rod. Increased bonded lengths resulted in higher bond slip values compared to lower equivalent bonded lengths. The proposed design model gave the best predictions of pull-out capacity compared with other existing models.

Push and Pull Motivations for Quitting: A three-wave investigation of predictors and consequences of turnover

We report a new analysis of data from a multi-year study, some of which were previously published in the current journal. A longitudinal sample of 380 computer specialists was followed over two years, yielding three measures each of job satisfaction, organizational commitment, and turnover intentions, as well as actual turnover, and reasons for leaving, at Times 2 and 3. Career paths were more diverse than the classical distinction between stayers and leavers implies. Furthermore, although the largest single group of leavers cited “push” reasons, conforming to the classical withdrawal model, a sizable number were attracted to another job (“pull motivation”). In a three-wave structural equation model, job (dis)satisfaction predicted turnover, while organizational commitment exerted its influence only via its association with job satisfaction. As expected, however, attitudes predicted turnover only for participants with push motivation. Quitting, in turn, predicted an improvement in both satisfaction and commitment, indicating that it paid off for the individual. The necessity to study consequences of turnover and to distinguish between different subgroups of stayers and leavers is emphasized.