Desenvolvimento de revestimentos de óxidos mistos nanoestruturados de TiO2/Al2O3 em substratos metálicos de aço AISI 1020 e estudo das propriedades anticorrosivas

Sóis liofilizados precursores de Al2O3/TiO2, foram preparados via tecnologia sol-gel, com diferentes porcentagens de óxido de titânio (5%, 10%, 15% e 20%, em massa). Os sóis liofilizados foram caracterizados por meio de diversas análises, com o intuito de obter informações sobre o comportamento térmico, fases presentes, tamanho de partícula, composição e uniformidade das amostras. Os resultados obtidos indicam que os sóis apresentam as fases boemita e anatase, com partículas de tamanho nanométrico, tem composições muito similares quando analisadas em pontos distintos, átomos bem dispersos e distribuídos. Após esta etapa, amostras de aço AISI 1020 foram recobertas com estes sóis através do método dip-coating, o comportamento corrosivo foi estudado por meio de ensaios eletroquímicos e a morfologia das camadas, analisadas por meio de microscopias. Observou-se que as camadas eram uniformes e recobriam por completo toda a superfície das amostras, os ensaios de polarização indicaram melhorias no potencial eletroquímico para amostras recobertas, em comparação com amostras de aço sem recobrimento. O monitoramento de circuito aberto apresentou bons ajustes, indicando bom comportamento da camada. Notou-se pelas microscopias a presença de pontos de corrosão em algumas amostras antes dos ensaios, suspeitando-se que os resultados obtidos teriam sido melhores, caso houvesse um maior controle do processo de recobrimento.

Effect of Cl- on the corrosive wear of AISI 321 stainless steel in H2SO4 solution

The effect of Cl- on the corrosive wear behaviour of AISI 321 stainless steel in H2SO4 solution was studied via the corrosive wear rate, the load bearing capacity of passive film and the relationship between pitting and corrosive wear. There is a critical load at natural potential, below which the corrosive wear rate is slightly lowered by Cl-, while above which is increased. At natural potential there are more pits at low load than that at a higher one in the wear tracks and the pits are also deeper. The load bearing capacity is lowered by Cl- at passive region and then the corrosive wear rate increased.

Stress corrosion cracking of AISI 321 stainless steel in acidic chloride solution

The stress corrosion cracking (SCC) of LambdaISI 321 stainless steel in acidic chloride solution was studied by slow strain rate (SSR) technique and fracture mechanics method. The fractured surface was characterized by cleavage fracture. In order to clarify the SCC mechanism, the effects of inhibitor KI on SCC behaviour were also included in this paper. A study showed that the inhibition effects of KI on SCC were mainly attributed to the anodic reaction of the corrosion process. The results of strain distribution in front of the crack tip of the fatigue pre-cracked plate specimens in air, in the blank solution (acidic chloride solution without inhibitor KI) and in the solution added with KI measured by speckle interferometry (SPI) support the unified mechanism of SCC and corrosion fatigue cracking (CFC).

Parameter studies of fibre laser micro-welding of AISI 316L using Taguchi method

This paper discusses the application of the Taguchi experimental design approach in optimizing the key process parameters for micro-welding of thin AISI 316L foil using the 100W CW fibre laser. A L16 Taguchi experiment was conducted to systematically understand how the power, scanning velocity, focus position, gas flow rate and type of shielding gas affect the bead dimensions. The welds produced in the L16 Taguchi experiment was mainly of austenite cellular-dendrite structure with an average grain size of 5µm. An exact penetration weld with the largest penetration to fusion width ratio was obtained. Among those process parameters, the interaction between power and scanning velocity presented the strongest effect to the penetration to fusion width ratio and the power was found to be the predominantly important factor that drives the interaction with other factors to appreciably affect the bead dimensions.

Prediction of surface roughness during hard turning of AISI 4340 steel (69 HRC)

In this study, 39 sets of hard turning (HT) experimental trials were performed on a Mori-Seiki SL-25Y (4-axis) computer numerical controlled (CNC) lathe to study the effect of cutting parameters in influencing the machined surface roughness. In all the trials, AISI 4340 steel workpiece (hardened up to 69 HRC) was machined with a commercially available CBN insert (Warren Tooling Limited, UK) under dry conditions. The surface topography of the machined samples was examined by using a white light interferometer and a reconfirmation of measurement was done using a Form Talysurf. The machining outcome was used as an input to develop various regression models to predict the average machined surface roughness on this material. Three regression models - Multiple regression, Random Forest, and Quantile regression were applied to the experimental outcomes. To the best of the authors’ knowledge, this paper is the first to apply Random Forest or Quantile regression techniques to the machining domain. The performance of these models was compared to each other to ascertain how feed, depth of cut, and spindle speed affect surface roughness and finally to obtain a mathematical equation correlating these variables. It was concluded that the random forest regression model is a superior choice over multiple regression models for prediction of surface roughness during machining of AISI 4340 steel (69 HRC).

Parametric design optimization of hard turning of AISI 4340 steel (69 HRC)

Continuous research endeavors on hard turning (HT), both on machine tools and cutting tools, have made the previously reported daunting limits easily attainable in the modern scenario. This presents an opportunity for a systematic investigation on finding the current attainable limits of hard turning using a CNC turret lathe. Accordingly, this study aims to contribute to the existing literature by providing the latest experimental results of hard turning of AISI 4340 steel (69 HRC) using a CBN cutting tool. An orthogonal array was developed using a set of judiciously chosen cutting parameters. Subsequently, the longitudinal turning trials were carried out in accordance with a well-designed full factorial-based Taguchi matrix. The speculation indeed proved correct as a mirror finished optical quality machined surface (an average surface roughness value of 45 nm) was achieved by the conventional cutting method. Furthermore, Signal-to-noise (S/N) ratio analysis, Analysis of variance (ANOVA), and Multiple regression analysis were carried out on the experimental datasets to assert the dominance of each machining variable in dictating the machined surface roughness and to optimize the machining parameters. One of the key findings was that when feed rate during hard turning approaches very low (about 0.02mm/rev), it could alone be most significant (99.16%) parameter in influencing the machined surface roughness (Ra). This has, however also been shown that low feed rate results in high tool wear, so the selection of machining parameters for carrying out hard turning must be governed by a trade-off between the cost and quality considerations.

Microstructure, mechanical properties and chemical degradation of brazed AISI 316 stainless steel/alumina systems

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Comportamiento de los aceros refractarios AISI 304 y HP40+Nb sometidos a altas temperaturas y una atmósfera oxi-carburizante

Tesis (Maestría en Ciencias de la Ingeniería Mécanica con Especialidad en Materiales) UANL

Comportamiento de los aceros refractarios AISI 304 y HP40+Nb sometidos a altas temperaturas y una atmósfera oxi-carburizante

Tesis (Maestría en Ciencias de la Ingeniería Mécanica con especialidad en Materiales) U.A.N.L.

Efectos microestructurales sobre el desgaste en acero tipo AISI D2 [por] Efrén Sauceda Tello

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) U.A.N.L.

Estudio de la precipitación de carburos en el acero inoxidable AISI 304 en enfriamiento contínuo [por] Juan Pablo Vázquez Hernández

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) U.A.N.L.

Geometría fractal de las fronteras de grano del acero AISI 304 sometido a deformación por Víctor Miguel Trejo Ramón

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) U.A.N.L.

Efecto de los carburos en el desgaste del acero tipo AISI D2

Tesis (Maestro en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) UANL, 1998.

Propagación de grietas en un acero inoxidable del tipo AISI 304 recubierto con una aleación resistente al desgaste

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) U.A.N.L.

Tratamiento térmico de anillos de acero AISI 4140.

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) UANL, 2012.