High resolution spectroscopy of (CH3OH)-C-13 around the 10R(20) CO2 laser emission: New FIR laser lines, frequency measurements and assignments

We investigated the IR absorption spectrum of (CH3OH)-C-13 around the frequency of the 10R(20) CO2 laser line. We found two absorption lines which can be excited by 10R(20) and studied the FIR laser emissions excited by this pump line using a waveguide CO2 laser of 300 MHz tunability: We report two new FIR laser lines of large offset, not previously observed due to their weakness and closeness to other stronger lines. We measured the frequencies of five FIR laser lines for the first time by an accurate heterodyne technique and present the complete assignments of the IR-FIR laser systems relative to this pump line. Furthermore we present new frequency values for two FIR laser lines whose frequencies had been previously wrongly measured. Copyright (C) 1997 Elsevier B.V. Ltd.

Optically pumped submillimeter laser lines from CD2Cl2 using a large tunability CW CO2 laser

Twenty-five new laser lines have been obtained is the wavelength region from 155 to 830 mu m by optically pumping the CD2Cl2 (deuterated dichloromethane) molecule with a CW CO3 laser having a tunability range of 300 MHz. The wavelength, polarization relative to that of CO2 pumping radiation, and offset relative to the CO2 center frequency were determined for all of the new lines and some other already known laser emissions. For all of them we give also the relative intensity and the optimum pressure of operation.

NEW FIR LASER LINES AND FREQUENCY MEASUREMENTS FROM OPTICALLY PUMPED CD-13(3)OH-3

We report the discovery of 57 new fir laser lines from (CD3OH)-C-13 molecule optically pumped by a waveguide CO2 laser of 300 MHz tunability. For all lines, precise frequency offset measurements between the CO2 line center and the center of the absorbing (CD3OH)-C-13 line were performed using the transferred Lamb-Dip technique. We have also measured directly the frequency of seven FIR laser lines by heterodyning with already known laser lines.We present a complete list of all known laser lines (134) and frequency measurements (24) for this molecule.

High resolution spectroscopy of 13CH3OH around the 10R(20) CO2 laser emission: New FIR laser lines, frequency measurement and assignments

We investigated the IR absorption spectrum of 13CH3OH around the frequency of the 10R(20) CO2 laser line. We found two absorption lines which can be excited by 10R(20) and studied the FIR laser emissions excited by this pump line using a waveguide CO2 laser of 300 MHz tunability. We report two new FIR laser lines of large offset, not previously observed due to their weakness and closeness to other stronger lines. We measured the frequencies of five FIR laser lines for the first time by an accurate heterodyne technique and present the complete assignments of the IR-FIR laser systems relative to this pump line. Furthermore we present new frequency values for two FIR laser lines whose frequencies had been previously wrongly measured. Copyright © 1997 Elsevier Science Ltd.

Transmissão DSL em modo fantasma: medições e avaliação de desempenho

A demanda por taxa de bits vem aumentando a cada ano, devido principalmente pela incorporação de aplicativos online ao cotidiano das pessoas. Assim, as companhias prestadoras deste tipo de serviço estão sempre investindo em pesquisa por tecnologias que possibilitem o aumento da taxa de bits com um bom custo-benefício. Seguindo esta perspectiva, este trabalho apresenta o modo de transmissão fantasma (Phantom mode), que visa aumentar a taxa total de transmissão de bits em sistemas DSL, quando múltiplos pares de cobre estão disponíveis. Aqui também são mostrados resultados e discussões importantes sobre desempenho do modo de transmissão fantasma. Também são discutidos procedimentos para a execução de medições de modo fantasma em frequências de 100 kHz a 300 MHz, em uma maneira que permite a medição de modo fantasma e modo diferencial com o mesmo setup. Novos resultados são apresentados sobre canal direto, far-end crosstalk (FEXT) e conversão de modo, para um cabo Cat-5e de 50 metros. Dentre outros fatos, foram verificadas grandes diferenças no canal direto de modo fantasma quando foram comparadas medições com cabo enrolado e desenrolado, e que a forma como o modo fantasma _e construção da influência bastante no comportamento das curvas de canal direto, FEXT e conversão de modo. Também são apresentados resultados de estimação da taxa de bits quando são usados modo fantasma e modo diferencial simultaneamente, e observou-se que ha um ganho de ate 60% quando foram usados este dois modos e vectoring.

Projeto de um monopolo Hi para aplicações no sistema brasileiro de TV digital

A presente pesquisa trata o projeto e análise de uma antena monopolo planar com geometria modificada visando sua utilização para recepção do sinal de TV digital operante no Brasil na faixa de 470 MHz a 806 MHz. Faixa essa contida no espectro de UHF – Ultra High Frequency (300 MHz a 3 GHz). Para desenvolvimento desse trabalho foi tomado como referência à antena denominada “The Hi Monopole”. Que originalmente foi apresentada para operar em sistemas UWB (Ultra Wide Band) em 3,1 a 10,6 GHz. Para o desenvolvimento do trabalho proposto, diferentes técnicas de adequação da antena podem ser utilizadas para operação em banda larga, tais como: modificação na estrutura da antena, carregamento resistivo, chaveamento, utilização de elementos parasitas e estruturas de casamento. O projeto de antenas banda larga pode ser realizado a partir de três abordagens diferentes: domínio do tempo, domínio da frequência e método de expansão por singularidades. O método no domínio da frequência foi empregado neste trabalho para o projeto da antena proposta, algumas das técnicas supracitadas foram analisadas almejando o aumento da largura de banda, sendo confeccionado um protótipo da antena para validar os conceitos empregados. A antena foi então projetada para a faixa de 470 MHz a 890 MHz. O protótipo construído para essa mesma faixa apresentou bons resultados, o que valida à técnica empregada. Aspectos positivos e negativos do uso desta técnica são discutidos ao longo do trabalho. O programa computacional comercial CST® MICROWAVE STUDIO, baseado na Técnica da Integração Finita (FIT), foi usado para simulações no domínio da frequência.

Correlation between carotid bifurcation calcium burden on non-enhanced CT and percentage stenosis, as confirmed by digital subtraction angiography

Objectives: Previous evidence supports a direct relationship between the calcium burden (volume) on post-contrast CT with the percent internal carotid artery (ICA) stenosis at the carotid bifurcation. We sought to further investigate this relationship by comparing non-enhanced CT (NECT) and digital subtraction angiography (DSA). Methods: 50 patients (aged 41-82 years) were retrospectively identified who had undergone cervical NECT and DSA. A 64-multidetector array CT (MDCT) scanner was utilised and the images reviewed using preset window widths/levels (30/300) optimised to calcium, with the volumes measured via three-dimensional reconstructive software. Stenosis measurements were performed on DSA and luminal diameter stenoses >40% were considered "significant". Volume thresholds of 0.01, 0.03, 0.06, 0.09 and 0.12 cm(3) were utilised and Pearson's correlation coefficient (r) was calculated to correlate the calcium volume with percent stenosis. Results: Of 100 carotid bifurcations, 88 were available and of these 7 were significantly stenotic. The NECT calcium volume moderately correlated with percent stenosis on DSA r=0.53 (p<0.01). A moderate-strong correlation was found between the square root of calcium volume on NECT with percent stenosis on DSA (r=0.60, p<0.01). Via a receiver operating characteristic curve, 0.06 cm(3) was determined to be the best threshold (sensitivity 100%, specificity 90.1%, negative predictive value 100% and positive predictive value 46.7%) for detecting significant stenoses. Conclusion: This preliminary investigation confirms a correlation between carotid bifurcation calcium volume and percent ICA stenosis and is promising for the optimal threshold for stenosis detection. Future studies could utilise calcium volumes to create a "score" that could predict high grade stenosis.

Dynamics of the cold surface layer of polythermal Storglaciären, Sweden

Polythermal glaciers, i.e. glaciers with a combination of ice at and below the freezing point, are widespread in arctic and subarctic environments. The polythermal structure has major implications for glacier hydrology, ice flow and glacial erosion. However, the interplay of factors governing its spatial and temporal variations such as net mass balance, ice advection and water content in the ice is poorly investigated and as yet not fully understood. This study deals with a thorough investigation of the polythermal regime on Storglaciären, northern Sweden, a small valley glacier with a cold surface layer in the ablation area. Extensive field work was performed including mapping of the cold surface layer using ground-penetrating radar, ice temperature measurements, mass balance and ice velocity measurements. Analyses of these data combined with numerical modelling were used specifically to investigate the spatial and temporal variability of the cold surface layer, the spatial distribution of the water content just below the cold surface layer transition, the effect of radar frequency on the detection of the surface layer, and the sensitivity of the cold surface layer to changes in forcing. A comparison between direct temperature measurements in boreholes and ground-penetrating surveys shows that the radar-inferred cold-temperate transition depth is within ±1 m from the melting point of ice at frequencies above ~300 MHz. At frequencies below ~155 MHz, the accuracy degrades because of reduced scattering efficiency that occurs when the scatterers become much smaller compared to the wavelength. The mapped spatial pattern of the englacial cold-temperate transition boundary is complex. This pattern reflects the observed spatial variation in net loss of ice at the surface by ablation and vertical advection of ice, which is suggested to provide the predominant forcing of the cold surface layer thickness pattern. This is further supported by thermomechanical modeling of the cold surface layer, which indicates high sensitivity of the cold surface layer thickness to changes in vertical advection rates. The water content is the least investigated quantity that is relevant for the thermal regime of glaciers, but also the most difficult to assess. Spatial variability of absolute water content in the temperate ice immediately below the cold surface layer on Storglaciären was determined by combining relative estimates of water content from ground-penetrating radar data with absolute determination from temperature measurements and the thermal boundary condition at the freezing front. These measurements indicate large-scale spatial variability in the water content, which seems to arise from variations in entrapment of water at the firn-ice transition. However, this variability cannot alone explain the spatial pattern in the thermal regime on Storglaciären. Repeated surveys of the cold surface layer show a 22% average thinning of the cold surface layer on Storglaciären between 1989 and 2001. Transient thermomechanical modeling results suggest that the cold surface layer adapts to new equilibrium conditions in only a few decades after a perturbation in the forcing is introduced. An increased winter air temperature since mid-1980s seems to be the cause of the observed thinning of the cold surface layer. Over the last decades, mass balance measurements indicate that the glacier has been close to a steady state. The quasi-steady state situation is also reflected in the vertical advection, which shows no significant changes during the last decades. Increased winter temperatures at the ice surface would result in a slow-down of the formation of cold ice at the base of the cold surface layer and lead to a larger imbalance between net loss of ice at the surface and freezing of temperate ice at the cold-temperate transition.

Optimised polyolefin branch quantification by 13 C NMR spectroscopy

Quantitative branch determination in polyolefins by solid- and melt-state 13C NMR has been investigated. Both methods were optimised toward sensitivity per unit time. While solid-state NMR was shown to give quick albeit only qualitative results, melt-state NMR allowed highly time efficient accurate branch quantification. Comparison of spectra obtained using spectrometers operating at 300, 500 and 700 MHz 1H Larmor frequency, with 4 and 7~mm MAS probeheads, showed that the best sensitivity was achieved at 500 MHz using a 7 mm 13C-1H optimised high temperature probehead. For materials available in large quantities, static melt-state NMR, using large diameter detection coils and high coil filling at 300 MHz, was shown to produce comparable results to melt-state MAS measurements in less time. While the use of J-coupling mediated polarisation transfer techniques was shown to be possible, direct polarisation via single-pulse excitation proved to be more suitable for branch quantification in the melt-state. Artificial line broadening, introduced by FID truncation, was able to be reduced by the use of π pulse-train heteronuclear dipolar decoupling. This decoupling method, when combined with an extended duty-cycle, allowed for significant improvement in resolution. Standard setup, processing and analysis techniques were developed to minimise systematic errors contributing to the measured branch contents. The final optimised melt-state MAS NMR method was shown to allow time efficient quantification of comonomer content and distribution in both polyethylene- and polypropylene-co-α-olefins. The sensitivity of the technique was demonstrated by quantifying branch concentrations of 8 branches per 100,000 CH2 for an industrial ‘linear’ polyethylene in only 13 hours. Even lower degrees of 3–8 long-chain branches per 100,000 carbons were able to be estimated in just 24 hours for a series of γ-irradiated polypropylene homopolymers.

Temporal trends in the characteristics of children at antiretroviral therapy initiation in southern Africa: the IeDEA-SA Collaboration

BACKGROUND Since 2005, increasing numbers of children have started antiretroviral therapy (ART) in sub-Saharan Africa and, in recent years, WHO and country treatment guidelines have recommended ART initiation for all infants and very young children, and at higher CD4 thresholds for older children. We examined temporal changes in patient and regimen characteristics at ART start using data from 12 cohorts in 4 countries participating in the IeDEA-SA collaboration. METHODOLOGY/PRINCIPAL FINDINGS Data from 30,300 ART-naïve children aged <16 years at ART initiation who started therapy between 2005 and 2010 were analysed. We examined changes in median values for continuous variables using the Cuzick's test for trend over time. We also examined changes in the proportions of patients with particular disease severity characteristics (expressed as a binary variable e.g. WHO Stage III/IV vs I/II) using logistic regression. Between 2005 and 2010 the number of children starting ART each year increased and median age declined from 63 months (2006) to 56 months (2010). Both the proportion of children <1 year and ≥10 years of age increased from 12 to 19% and 18 to 22% respectively. Children had less severe disease at ART initiation in later years with significant declines in the percentage with severe immunosuppression (81 to 63%), WHO Stage III/IV disease (75 to 62%), severe anemia (12 to 7%) and weight-for-age z-score<-3 (31 to 28%). Similar results were seen when restricting to infants with significant declines in the proportion with severe immunodeficiency (98 to 82%) and Stage III/IV disease (81 to 63%). First-line regimen use followed country guidelines. CONCLUSIONS/SIGNIFICANCE Between 2005 and 2010 increasing numbers of children have initiated ART with a decline in disease severity at start of therapy. However, even in 2010, a substantial number of infants and children started ART with advanced disease. These results highlight the importance of efforts to improve access to HIV diagnostic testing and ART in children.

Similarity Mapplet: Interactive Visualization of the Directory of Useful Decoys and ChEMBL in High Dimensional Chemical Spaces

An Internet portal accessible at www.gdb.unibe.ch has been set up to automatically generate color-coded similarity maps of the ChEMBL database in relation to up to two sets of active compounds taken from the enhanced Directory of Useful Decoys (eDUD), a random set of molecules, or up to two sets of user-defined reference molecules. These maps visualize the relationships between the selected compounds and ChEMBL in six different high dimensional chemical spaces, namely MQN (42-D molecular quantum numbers), SMIfp (34-D SMILES fingerprint), APfp (20-D shape fingerprint), Xfp (55-D pharmacophore fingerprint), Sfp (1024-bit substructure fingerprint), and ECfp4 (1024-bit extended connectivity fingerprint). The maps are supplied in form of Java based desktop applications called “similarity mapplets” allowing interactive content browsing and linked to a “Multifingerprint Browser for ChEMBL” (also accessible directly at www.gdb.unibe.ch) to perform nearest neighbor searches. One can obtain six similarity mapplets of ChEMBL relative to random reference compounds, 606 similarity mapplets relative to single eDUD active sets, 30 300 similarity mapplets relative to pairs of eDUD active sets, and any number of similarity mapplets relative to user-defined reference sets to help visualize the structural diversity of compound series in drug optimization projects and their relationship to other known bioactive compounds.