The use of an electrostatic lens to enhance the efficiency of the electrospinning process

Electrospun scaffolds manufactured using conventional electrospinning configurations have an intrinsic thickness limitation, due to a charge build-up at the collector. To overcome this limitation, an electrostatic lens has been developed that, at the same relative rate of deposition, focuses the polymer jet onto a smaller area of the collector, resulting in the fabrication of thick scaffolds within a shorter period of time. We also observed that a longer deposition time (up to 13 h, without the intervention of the operator) could be achieved when the electrostatic lens was utilised, compared to 9–10 h with a conventional processing set-up and also showed that fibre fusion was less likely to occur in the modified method. This had a significant impact on the mechanical properties, as the scaffolds obtained with the conventional process had a higher elastic modulus and ultimate stress and strain at short times. However, as the thickness of the scaffolds produced by the conventional electrospinning process increased, a 3-fold decrease in the mechanical properties was observed. This was in contrast to the modified method, which showed a continual increase in mechanical properties, with the properties of the scaffold finally having similar mechanical properties to the scaffolds obtained via the conventional process at longer times. This “focusing” device thus enabled the fabrication of thicker 3-dimensional electrospun scaffolds (of thicknesses up to 3.5 mm), representing an important step towards the production of scaffolds for tissue engineering large defect sites in a multitude of tissues.

Mapping local solutions to entrenched transport problems: Key lessons regarding the use of geographical information technologies in community mapping with disadvantaged communities

There is an increasing interest in the use of information technology as a participatory planning tool, particularly the use of geographical information technologies to support collaborative activities such as community mapping. However, despite their promise, the introduction of such technologies does not necessarily promote better participation nor improve collaboration. In part this can be attributed to a tendency for planners to focus on the technical considerations associated with these technologies at the expense of broader participation considerations. In this paper we draw on the experiences of a community mapping project with disadvantaged communities in suburban Australia to highlight the importance of selecting tools and techniques which support and enhance participatory planning. This community mapping project, designed to identify and document community-generated transport issues and solutions, had originally intended to use cadastral maps extracted from the government’s digital cadastral database as the foundation for its community mapping approach. It was quickly discovered that the local residents found the cadastral maps confusing as the maps lacked sufficient detail to orient them to their suburb (the study area). In response to these concerns and consistent with the project’s participatory framework, a conceptual base map based on resident’s views of landmarks of local importance was developed to support the community mapping process. Based on this community mapping experience we outline four key lessons learned regarding the process of community mapping and the place of geographical information technologies within this process.

What factors influence nurses’ assessment practices? Development of the Barriers to Nurses’ use of Physical Assessment Scale

Aim To develop and psychometrically test the Barriers to Nurses’ use of Physical Assessment Scale. Background There is growing evidence of failure to recognise hospitalised patients at risk of clinical deterioration, in part due to inadequate physical assessment by nurses. Yet, little is known about the barriers to nurses’ use of physical assessment in the acute hospital setting and no validated scales have been published. Design Instrument development study. Method Scale development was based on a comprehensive literature review, focus groups, expert review and psychometric evaluation. The scale was administered to 434 acute care registered nurses working at a large Australian teaching hospital between June and July 2013. Psychometric analysis included factor analysis, model fit statistics and reliability testing. Results The final scale was reduced to 38 items representing seven factors, together accounting for 57.7% of the variance: (1) reliance on others and technology, (2) lack of time and interruptions, (3) ward culture, (4) lack of confidence, (5) lack of nursing role models, (6) lack of influence on patient care, and; (7) specialty area. Internal reliability ranged from .70 to .86. Conclusion Findings provide initial evidence for the validity and reliability of the Barriers to Nurses’ use of Physical Assessment Scale and point to the importance of understanding the organisational determinants of nurses’ assessment practices. The new scale has potential clinical and research applications to support nursing assessment in acute care settings.

Critical reflections on the use of participatory methodologies to build evaluation capacities in international development organisations

There has been a greater focus on strengthening evaluation capacity building (ECB) within development organisations in recent years. This can be attributed in part to the growing appreciation of the value of participatory and collaborative forms of evaluation. Evaluation is increasingly seen as an ongoing learning process and an important means of strengthening capacity and improving organisational performance (Horton et al., 2003:7). While there are many benefits of using participatory methodologies in ECB projects, our experiences and a review of the literature in this area highlight the many challenges, issues and contradictions that can affect the success of such ECB efforts. We discuss these issues, drawing on our learnings from the ongoing participatory action research (PAR) project 'Assessing Communication for Social Change’ (AC4SC). This four year project, which began in 2007, is a collaboration between communication and development academics and evaluation specialists from two Australian universities and communication for development practitioners and monitoring and evaluation (M&E) staff in the NGO Equal Access Nepal (EAN). The aim is to develop, implement, and evaluate a participatory methodology for assessing the social change impacts of community radio programs produced by EAN. It builds on previous projects that used ethnographic action research (EAR) methodology (Tacchi et al., 2007).

The use of phospholipid fatty acid analysis to measure impact of acid rock drainage on microbial communities in sediments

The impact of acid rock drainage (ARD) and eutrophication on microbial communities in stream sediments above and below an abandoned mine site in the Adelaide Hills, South Australia, was quantified by PLFA analysis. Multivariate analysis of water quality parameters, including anions, soluble heavy metals, pH, and conductivity, as well as total extractable metal concentrations in sediments, produced clustering of sample sites into three distinct groups. These groups corresponded with levels of nutrient enrichment and/or concentration of pollutants associated with ARD. Total PLFA concentration, which is indicative of microbial biomass, was reduced by >70% at sites along the stream between the mine site and as far as 18 km downstream. Further downstream, however, recovery of the microbial abundance was apparent, possibly reflecting dilution effect by downstream tributaries. Total PLFA was >40% higher at, and immediately below, the mine site (0-0.1 km), compared with sites further downstream (2.5-18 km), even after accounting for differences in specific surface area of different sediment samples. The increased microbial population in the proximity of the mine source may be associated with the presence of a thriving iron-oxidizing bacteria community as a consequence of optimal conditions for these organisms while the lower microbial population further downstream corresponded with greater sediments' metal concentrations. PCA of relative abundance revealed a number of PLFAs which were most influential in discriminating between ARD-polluted sites and the rest of the sites. These PLFA included the hydroxy fatty acids: 2OH12:0, 3OH12:0, 2OH16:0; the fungal marker: 18:2ω6; the sulfate-reducing bacteria marker 10Me16:1ω7; and the saturated fatty acids 12:0, 16:0, 18:0. Partial constrained ordination revealed that the environmental parameters with the greatest bearing on the PLFA profiles included pH, soluble aluminum, total extractable iron, and zinc. The study demonstrated the successful application of PLFA analysis to rapidly assess the toxicity of ARD-affected waters and sediments and to differentiate this response from the effects of other pollutants, such as increased nutrients and salinity.

Theorizing the use of multiple conceptual models in combination

Conceptual modelling continues to be an important means for graphically capturing the requirements of an information system. Observations of modelling practice suggest that modellers often use multiple conceptual models in combination, because they articulate different aspects of real-world domains. Yet, the available empirical as well as theoretical research in this area has largely studied the use of single models, or single modelling grammars. We develop a Theory of Combined Ontological Coverage by extending an existing theory of ontological expressiveness of conceptual modelling grammars. Our new theory posits that multiple conceptual models are used to increase the maximum coverage of the real-world domain being modelled, whilst trying to minimize the ontological overlap between the models. We illustrate how the theory can be applied to analyse sets of conceptual models. We develop three propositions of the theory about evaluations of model combinations in terms of users’ selection, understandability and usefulness of conceptual models.

Introduction : studying Indonesian media worlds at the intersections of area and cultural studies

When preparing this special issue,1 our discussions with the editorial board of the International Journal of Cultural Studies (IJCS) included a moment of simultaneous surprise and reflection, which we would like to use as a starting point for our introduction to the articles appearing here. This occurred during communications about the number and length of the articles required for a special issue. The board’s representative stipulated that a specific number of articles were to be written by Indonesian scholars. The request surprised us. We had neither discussed nor anticipated ethnic or national quotas for authorial participation. But although the request caught us off guard it also stimulated us to think about the two disciplinary terrains traversed in the articles to follow.

AITSL pilot projects [Queensland University of Technology : The existing school-based practices and processes for the use of NAPLAN data] Final report

This pilot project investigated the existing practices and processes of Proficient, Highly Accomplished and Lead teachers in the interpretation, analysis and implementation of National Assessment Program – Literacy and Numeracy (NAPLAN) data. A qualitative case study approach was the chosen methodology, with nine teachers across a variety of school sectors interviewed. Themes and sub-themes were identified from the participants’ interview responses revealing the ways in which Queensland teachers work with NAPLAN data. The data illuminated that generally individual schools and teachers adopted their own ways of working with data, with approaches ranging from individual/ad hoc, to hierarchical or a whole school approach. Findings also revealed that data are the responsibility of various persons from within the school hierarchy; some working with the data electronically whilst others rely on manual manipulation. Manipulation of data is used for various purposes including tracking performance, value adding and targeting programmes for specific groups of students, for example the gifted and talented. Whilst all participants had knowledge of intervention programmes and how practice could be modified, there were large inconsistencies in knowledge and skills across schools. Some see the use of data as a mechanism for accountability, whilst others mention data with regards to changing the school culture and identifying best practice. Overall, the findings showed inconsistencies in approach to focus area 5.4. Recommendations therefore include a more national approach to the use of educational data.

The primacy of vital signs – Acute care nurses’ and midwives’ use of physical assessment skills: A cross sectional study

BACKGROUND: Registered nurses and midwives play an essential role in detecting patients at risk of deterioration through ongoing assessment and action in response to changing health status. Yet, evidence suggests that clinical deterioration frequently goes unnoticed in hospitalised patients. While much attention has been paid to early warning and rapid response systems, little research has examined factors related to physical assessment skills. OBJECTIVES: To determine a minimum data set of core skills used during nursing assessment of hospitalised patients and identify nurse and workplace predictors of the use of physical assessment to detect patient deterioration. DESIGN: The study used a single-centre, cross-sectional survey design. SETTING and PARTICIPANTS: The study included 434 registered nurses and midwives (Grades 5-7) involved in clinical care of patients on acute care wards, including medicine, surgery, oncology, mental health and maternity service areas, at a 929-bed tertiary referral teaching hospital in Southeast Queensland, Australia. METHODS: We conducted a hospital-wide survey of registered nurses and midwives using the 133-item Physical Assessment Skills Inventory and the 58-item Barriers to Registered Nurses’ Use of Physical Assessment scale. Median frequency for each physical assessment skill was calculated to determine core skills. To explore predictors of core skill utilisation, backward stepwise general linear modelling was conducted. Means and regression coefficients are reported with 95% confidence intervals. A p value < .05 was considered significant for all analyses. RESULTS: Core skills used by most nurses every time they worked included assessment of temperature, oxygen saturation, blood pressure, breathing effort, skin, wound and mental status. Reliance on others and technology (F = 35.77, p < .001), lack of confidence (F = 5.52, p = .02), work area (F = 3.79, p = .002), and clinical role (F = 44.24, p < .001) were significant predictors of the extent of physical assessment skill use. CONCLUSIONS: The increasing acuity of the acute care patient plausibly warrants more than vital signs assessment; however, our study confirms nurses’ physical assessment core skill set is mainly comprised of vital signs. The focus on these endpoints of deterioration as dictated by early warning and rapid response systems may divert attention from and devalue comprehensive nursing assessment that could detect subtle changes in health status earlier in the patient's hospitalisation.

Too much knowledge for a nurse? Use of physical assessment by final-semester nursing students

There is debate around the scope of physical assessment skills that should be taught in undergraduate nursing programs. Yet this debate is largely uninformed by evidence on what is learned and practiced by nursing students. This study examined the pattern and correlates of physical assessment skill utilization by 208 graduating nursing students at an Australian university, including measures of knowledge, frequency of use and perceived barriers to physical assessment skills during clinical practice. Of the 126 skills surveyed, on average only five were used every time students practiced. Core skills reflected inspection or general observation of the patient; none involved complex palpation, percussion or auscultation. Skill utilization was also shaped by specialty area. Most skills (70%) were, on average, never performed or learned and students perceived nursing physical assessment was marginalized in both university and workplace contexts. Lack of confidence was thus a significant barrier to use of skills. Based on these findings we argue that the current debate must shift to how we might best support students to integrate comprehensive physical assessment into nursing practice.

Use of Petrifilm(R) 3M to assess coliform numbers on lamb carcasses.

Petrifilm(R) (6410) was used directly on lamb carcasses to enumerate coliforms. 10 sites on 30 carcasses were sampled at each of 4 separate meat processing establishments (works). Coliform counts obtained by this technique were statistically analysed using analysis of variance (ANOVA) to select the optimum sampling sites on the carcass and to assess contamination of the carcass by gut flora at a particular establishment. There was a large variation between sites and between works. In general, works 3 and 4 produced cleaner carcasses than works 2, which in turn was cleaner than works 1. Works 1, 2 and 4 used conventional dressing techniques and works 3 used the inverted dressing method, therefore, the coliform counts found at works 3 and 4 are achievable regardless of dressing technique. Coliform bacteria were most concentrated around the posterior pelvic rim and less prevalent at the carcass extremities. The posterior pelvic rim (sites 3 and 4) had higher (P < 0.05) coliform counts than the exterior ventral flank area (sites 5, 6, 7 and 8), which in turn had higher (P < 0.05) counts than the proximal hind and proximal fore limbs (sites 1, 2, 9 and 10) across all works. With in-line routine testing it is recommended that the majority of carcasses sampled should give coliform counts of <50 cfu/20 cm2 for sites 4 and 8. Reprinted with permission from Journal of Food Protection. Copyright held by the International Association of Food Protection, Des Moines, Iowa, USA. Authors affifiation. J.A.Guthrie & K.J.Dunlop International Food Institute of Queensland, Department of Primary Industries, Rockhampton and G.A.Saunders Veterinary Public Health Division, Livestock and Meat Authority of Queensland, Emerald.

Use of electronic portal imaging devices for electron treatment verification

This study aims to help broaden the use of electronic portal imaging devices (EPIDs) for pre-treatment patient positioning verification, from photon-beam radiotherapy to photon- and electron-beam radiotherapy, by proposing and testing a method for acquiring clinicallyuseful EPID images of patient anatomy using electron beams, with a view to enabling and encouraging further research in this area. EPID images used in this study were acquired using all available beams from a linac configured to deliver electron beams with nominal energies of 6, 9, 12, 16 and 20 MeV, as well as photon beams with nominal energies of 6 and 10 MV. A widely-available heterogeneous, approximately-humanoid, thorax phantom was used, to provide an indication of the contrast and noise produced when imaging different types of tissue with comparatively realistic thicknesses. The acquired images were automatically calibrated, corrected for the effects of variations in the sensitivity of individual photodiodes, using a flood field image. For electron beam imaging, flood field EPID calibration images were acquired with and without the placement of blocks of water-equivalent plastic (with thicknesses approximately equal to the practical range of electrons in the plastic) placed upstream of the EPID, to filter out the primary electron beam, leaving only the bremsstrahlung photon signal. While the electron beam images acquired using a standard (unfiltered) flood field calibration were observed to be noisy and difficult to interpret, the electron beam images acquired using the filtered flood field calibration showed tissues and bony anatomy with levels of contrast and noise that were similar to the contrast and noise levels seen in the clinically acceptable photon beam EPID images. The best electron beam imaging results (highest contrast, signal-to-noise and contrast-to-noise ratios) were achieved when the images were acquired using the higher energy electron beams (16 and 20 MeV) when the EPID was calibrated using an intermediate (12 MeV) electron beam energy. These results demonstrate the feasibility of acquiring clinically-useful EPID images of patient anatomy using electron beams and suggest important avenues for future investigation, thus enabling and encouraging further research in this area. There is manifest potential for the EPID imaging method proposed in this work to lead to the clinical use of electron beam imaging for geometric verification of electron treatments in the future.

A case study on the use of legume crop rotations in sugarcane

Growing legume fallow crops has proven to be an important factor in reducing the yield decline effect in sugarcane production. Legumes can also provide a direct economic benefit to sugarcane farmers by providing a source of nitrogen. Further, in some instances, income can flow from the sale, of grain or seed. The following case study provides an insight into the changes made by Russell Young, a sugarcane farmer situated in the Rita Island area of the Burdekin district. The case study focuses on the economics of the old farming system versus a new farming system. The old farming system is based on the conventional farming practices previously used by the Young family in 2002 compared to the 2006 farming system which involves a reduction in tillage practices and use of a Soybean rotational crop for seed production. A whole-of-farm was used to assess the impact of the new farming system on farm profitability. A whole-of-farm economic analysis looks at the impact of a change in farming practice across the whole business, rather than focusing on one single component. This case study is specific to an individual grower’s situation and is not representative of all situations. When evaluating a farming system change, it is important to have a detailed plan.

Geological factors affecting on after-use of Finnish cut-over peatlands : with implications on the carbon accumulation

In Finland, peat harvesting sites are utilized down almost to the mineral soil. In this situation the properties of mineral subsoil are likely to have considerable influence on the suitability for the various after-use forms. The aims of this study were to recognize the chemical and physical properties of mineral subsoils possibly limiting the after-use of cut-over peatlands, to define a minimum practice for mineral subsoil studies and to describe the role of different geological areas. The future percentages of the different after-use forms were predicted, which made it possible to predict also carbon accumulation in this future situation. Mineral subsoils of 54 different peat production areas were studied. Their general features and grain size distribution was analysed. Other general items studied were pH, electrical conductivity, organic matter, water soluble nutrients (P, NO3-N, NH4-N, S and Fe) and exchangeable nutrients (Ca, Mg and K). In some cases also other elements were analysed. In an additional case study carbon accumulation effectiveness before the intervention was evaluated on three sites in Oulu area (representing sites typically considered for peat production). Areas with relatively sulphur rich mineral subsoil and pool-forming areas with very fine and compact mineral subsoil together covered approximately 1/5 of all areas. These areas were unsuitable for commercial use. They were recommended for example for mire regeneration. Another approximate 1/5 of the areas included very coarse or very fine sediments. Commercial use of these areas would demand special techniques - like using the remaining peat layer for compensating properties missing from the mineral subsoil. One after-use form was seldom suitable for one whole released peat production area. Three typical distribution patterns (models) of different mineral subsoils within individual peatlands were found. 57 % of studied cut-over peatlands were well suited for forestry. In a conservative calculation 26% of the areas were clearly suitable for agriculture, horticulture or energy crop production. If till without large boulders was included, the percentage of areas suitable to field crop production would be 42 %. 9-14 % of all areas were well suitable for mire regeneration or bird sanctuaries, but all areas were considered possible for mire regeneration with correct techniques. Also another 11 % was recommended for mire regeneration to avoid disturbing the mineral subsoil, so total 20-25 % of the areas would be used for rewetting. High sulphur concentrations and acidity were typical to the areas below the highest shoreline of the ancient Litorina sea and Lake Ladoga Bothnian Bay zone. Also differences related to nutrition were detected. In coarse sediments natural nutrient concentration was clearly higher in Lake Ladoga Bothnian Bay zone and in the areas of Svecokarelian schists and gneisses, than in Granitoid area of central Finland and in Archaean gneiss areas. Based on this study the recommended minimum analysis for after-use planning was for pH, sulphur content and fine material (<0.06 mm) percentage. Nutrition capacity could be analysed using the natural concentrations of calcium, magnesium and potassium. Carbon accumulation scenarios were developed based on the land-use predictions. These scenarios were calculated for areas in peat production and the areas released from peat production (59300 ha + 15 671 ha). Carbon accumulation of the scenarios varied between 0.074 and 0.152 million t C a-1. In the three peatlands considered for peat production the long term carbon accumulation rates varied between 13 and 24 g C m-2 a-1. The natural annual carbon accumulation had been decreasing towards the time of possible intervention.

Layout plan of area around the workshop "Trud - Schastʻė"

Digital image