Reducing fouling during UHT treatment of goat's milk

Whole fresh goat's milk was heat treated at 135 degrees C for 4 s using a miniature UHT plant. The temperature of the milk in the preheating and sterilizer sections, and the milk flow rate were monitored to evaluate the overall heat transfer coefficient (OHTC). The decrease in OHTC was used to estimate the extent of fouling. Goat's milk fouled very quickly and run times of the UHT plant were short. The use of sodium hexametaphosphate, trisodium citrate and cation exchange resins to reduce ionic calcium prior to UHT processing, increased the pH and alcohol stability of the milk and markedly increased the run time of the UHT plant.

Effects of phosphates and citrate on sediment formation in UHT goats' milk

Sediment formation was investigated during UHT treatment of goats' milk, subjected to indirect treatment at 140 degrees C for 2 s, with upstream homogenisation. Stabilisers evaluated were sodium hexametaphosphate (SHMP), trisodium citrate (TSC), disodium hydrogen orthophosphate (DSHP), and sodium dihydrogen orthophosphate (SDHP). With no added stabiliser, goats' milk produced a heavy sediment on UHT treatment. Addition of SDHP reduced pH, had little effect on ionic calcium and did not substantially reduce sediment. However, addition of SHMP, DSHP and TSC each reduced ionic calcium, increased ethanol stability and reduced sediment. Following stabiliser additions, there was a good correlation between ethanol stability and ionic calcium (R-2=0.85) but not between ethanol stability and pH (R-2=0.08). Overall, reducing ionic calcium reduced the amount of sediment formed for all these three stabilisers, although there was no single trend line between sediment formation and ionic calcium concentration. Sediment formation was not well correlated with pH for TSC or for SHMP, but it was for DSHP, making it the only stabiliser where sediment formation correlated well both with ionic calcium and pH, which might account for its effectiveness at higher ionic calcium levels. Sediment was much reduced when the temperature was reduced from 140 degrees C to 125 degrees C and 114 degrees C. There were no further changes in sediment on storage for two weeks. Analysis of the sediment showed that it was predominantly fat and protein, with a mass ratio ranging between 1.43:1 and 1.67:1. Its mineral content was usually less than 5% of dry weight. The maximum amounts of P and Ca were found to be 2.32% and 1.63%, respectively.

Survival of probiotics encapsulated in chitosan-coated alginate beads in yoghurt from UHT- and conventionally treated milk during storage

Survival of the microencapsulated probiotics, Lactobacillus acidophilus 547, Bifidobacterium bifidum ATCC 1994, and Lactobacillus casei 01, in stirred yoghurt from UHT- and conventionally treated milk during low temperature storage was investigated. The probiotic cells both as free cells and microencapsulated cells (in alginate beads coated with chitosan) were added into 20 g/100 g total solids stirred yoghurt from UHT-treated milk and 16 g/100 g total solids yoghurt from conventionally treated milk after 3.5 h of fermentation. The products were kept at 4 degrees C for 4 weeks. The survival of encapsulated probiotic bacteria was higher than free cells by approximately 1 log cycle. The number of probiotic bacteria was maintained above the recommended therapeutic minimum (10(7) cfu g(-1)) throughout the storage except for R bifidum. The viabilities of probiotic bacteria in yoghurts from both UHT- and conventionally treated milks were not significantly (P > 0.05) different. (c) 2004 Swiss Society of Food Science and Technology. Published by Elsevier Ltd. All rights reserved.

The influence of temperature on the foaming of milk

The effect of temperature (5-85 °C) on the foaming properties of cows' milk was investigated. The foaming properties of milk as a function of temperature varied considerably depending on fat content and the processing conditions used in manufacture. Skim milk foams were most stable when formed at 45 °C. Milk fat had a detrimental effect on foam formation and stability of whole milk especially in the temperature range 15-45 °C. The detrimental effects of milk fat on foaming properties were reduced by homogenization and ultra-high-temperature (UHT) treatment. No correlation was observed between foam formation and surface tension of whole milk in the temperature range 15-45 °C. There was a pronounced difference in the bubble size distributions of whole milk and skim milk especially at half-life of the foams. Bubbles in whole milk foams were smaller and showed a higher degree of rupture as a result of coalescence than those in skim milk foams.

Effects of different calcium salts on properties of milk related to heat stability

Insoluble calcium salts were added to milk to increase total calcium by 30 mM, without changing properties influencing heat stability, such as pH and ionic calcium. There were no major signs of instability associated with coagulation, sediment formation or fouling when subjected to ultra high temperature (UHT) and in-container sterilisation. The buffering capacity was also unaltered. On the other hand, addition of soluble calcium salts reduced pH, increased ionic calcium and caused coagulation to occur. Calcium chloride showed the largest destabilising effect, followed by calcium lactate and calcium gluconate. Milk became unstable to UHT processing at lower calcium additions compared to in-container sterilisation.

Predictions of some product parameters based on the processing conditions of ultra-high-temperature milk plants

The temperature-time profiles of 22 Australian industrial ultra-high-temperature (UHT) plants and 3 pilot plants, using both indirect and direct heating, were surveyed. From these data, the operating parameters of each plant, the chemical index C*, the bacteriological index B* and the predicted changes in the levels of beta-lactoglobulin, alpha-lactalbumin, lactulose, furosine and browning were determined using a simulation program based on published formulae and reaction kinetics data. There was a wide spread of heating conditions used, some of which resulted in a large margin of bacteriological safety and high chemical indices. However, no conditions were severe enough to cause browning during processing. The data showed a clear distinction between the indirect and direct heating plants. They also indicated that degree of denaturation of alpha-lactalbumin varied over a wide range and may be a useful discriminatory index of heat treatment. Application of the program to pilot plants illustrated its value in determining processing conditions in these plants to simulate the conditions in industrial UHT plants. (C) 2008 Elsevier Ltd. All rights reserved.

Comparison of heat stability of goat milk subjected to ultra-high temperature and in-container sterilisation

Goatmilk with and without stabilizing salt was subjected to in-container and UHTsterilization. Heatstability was assessed by measuring the amount of sediment in the milk. Without stabilizing salts, goatmilk usually produced less sediment when subjected to in-containersterilization compared with UHT processing. Addition of stabilizing salts up to 12.8 mM resulted in a progressive increase in sediment for in-containersterilization. In contrast, adding stabilizing salts at 6.4 mM initially reduced sediment formation in UHT-treated milk but addition of stabilizing salts at 12.8 mM increased sediment formation. Adding stabilizing salts to goatmilk increased pH, decreased ionic calcium, and increased ethanol stability. Adding up to 2 mM calcium chloride increased sediment formation more after UHT treatment than after in-containersterilization. These results suggest that no single mechanism or set of reactions causes milk to produce sediment during heating and that the favored pathway is different for UHT and in-containersterilization processes. Poor heatstability could be induced both by increasing ionic calcium and by decreasing it. Ethanol stability is not a good indicator of heatstability for in-containersterilization, but it may be for UHTsterilization, if milk does not enter the region of poor heatstability found at low concentrations of ionic calcium.

Effect of seasonal variation on some physical properties and heat stability of milk subjected to ultra-high temperature and in-container sterilisation

Heat stability was evaluated in bulk raw milk, collected throughout the year and subjected to ultra-high temperature (UHT) or in-container sterilisation, with and without added calcium chloride (2 mM), disodium hydrogen phosphate (DSHP, 10 mM) and trisodium citrate (TSC, 10 mM). More sediment was observed following in-container sterilisation (0.24%) compared with UHT (0.19%). Adding CaCl2 made the milk more unstable to UHT than to in-container sterilisation, while adding DSHP and TSC made the milk more unstable during in-container sterilisation than to UHT processing, although TSC addition increased the sediment formed by UHT processing. Better heat stability was observed in autumn and winter than in spring and summer following UHT. However, following in-container sterilisation, samples with added stabilising salts showed significantly improved heat stability in autumn, whereas with added CaCl2, the best heat stability was observed in spring. No correlation was found between urea and heat stability. DSHP and TSC made the milk more unstable during in-container sterilisation than to UHT processing, although TSC addition increased the sediment formed by UHT processing. Better heat stability was observed in autumn and winter than in spring and summer following UHT. However, following in-container sterilisation, samples with added stabilising salts showed significantly improved heat stability in autumn, whereas with added CaCl2, the best heat stability was observed in spring. No correlation was found between urea and heat stability.

Fabrication of disposable voltammetric electronic tongues by using Prussian Blue films electrodeposited onto CD-R gold surfaces and recognition of milk adulteration

A new approach to fabricate a disposable electronic tongue is reported. The fabrication of the disposable sensor aimed the integration of all electrodes necessary for measurement in the same device. The disposable device was constructed with gold CD-R and copper sheets substrates and the sensing elements were gold, copper and a gold surface modified with a layer of Prussian Blue. The relative standard deviation for signals obtained from 20 different disposable gold and 10 different disposable copper electrodes was below 3.5%. The performance, electrode materials and the capability of the device to differentiate samples were evaluated for taste substances model, milk with different pasteurization processes (homogenized/pasteurized, ultra high temperature (UHT) pasteurized and UHT pasteurized with low fat content) and adulterated with hydrogen peroxide. In all analysed cases, a good separation between different samples was noticed in the score plots obtained from the principal component analysis (PCA). Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

Qualidade microbiológica de leite UHT caprino: pesquisa de bactérias dos gêneros Staphylococcus, Bacillus e Clostridium

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Healing process of incisor teeth of diabetic rats replanted after storage in milk

Several local factors that influence the healing process of replanted teeth have been investigated. However, it remains unclear how systemic alterations, such as diabetes mellitus, affect the prognosis of these cases. The purpose of this study was to evaluate the healing process of incisors of non-controlled diabetic rats replanted after storage in bovine long shelf-life (UHT) whole milk. Thirty-two rats were randomly assigned to receive an endovenous injection of either citrate buffer solution (group I - control; n = 16) or streptozotocin dissolved in citrate buffer solution to induce diabetes (group II; n = 16). After confirmation of the diabetic status by analysis of the glycemic levels, the maxillary right incisor of each animal was extracted and immersed in milk for 60 min. The root canals of teeth were then instrumented, and were filled with a calcium hydroxide-based dressing and replanted into their sockets. All animals received systemic antibiotic and were killed by anesthetic overdose 10 and 60 days after replantation. The specimens containing the replanted teeth were removed, fixed, decalcified, and embedded in paraffin. Semi-serial 6-mu m-thick sections were obtained and stained with hematoxylin and eosin for histologic and histometric analyses. The results showed that the connective tissue adjacent to the root surface was less organized in the diabetic animals than in the control animals in both periods; the root dentin was less severely affected by root resorption in the diabetic rats; there were no significant differences between the control and diabetic groups regarding the occurrence of replacement resorption and inflammatory resorption.

Methods of detecting fouling caused by heating of milk

Fouling is the deposition of milk solids on heat transfer sur aces, particularly heat exchangers. It is a major industrial problem, which causes a decrease in heat transfer efficiency and shortens run times. The resultant effect is a decrease in process efficiency and economy. For studying and monitoring deposit formation, suitable fouling detectors or methods of measuring the deposit are required. This can be achieved through direct means, whereby the deposit is analyzed after a certain time, or indirectly through instrumentation for monitoring parameters such as temperature, pressure, flow rate, overall heat transfer coefficient, heat flux, and other physical properties. This article reviews the various reported fouling detection methods.

MiLK: Transforming everyday places into dynamic learning spaces with mobile and web technologies

This paper explores how game authoring tools can teach processes that transform everyday places into engaging learning spaces. It discusses the motivation inherent in playing games and creating games for others, and how this stimulates an iterative process of creation and reflection and evokes a natural desire to engage in learning. The use of MiLK at the Adelaide Botanic Gardens is offered as a case in point. MiLK is an authoring tool that allows students and teachers to create and share SMS games for mobile phones. A group of South Australian high school students used MiLK to play a game, create their own games and play each other’s games during a day at the gardens. This paper details the learning processes involved in these activities and how the students, without prompting, reflected on their learning, conducted peer assessment, and engaged in a two-way discussion with their teacher about new technologies and their implications for learning. The paper concludes with a discussion of the needs and requirements of 21st century learners and how MiLK can support constructivist and connectivist teaching methods that engage learners and will produce an appropriately skilled future workforce.

MILK : the Mobile Informal Learning Kit. Collaborating to design successful mobile learning applications

This paper suggests ways for educators and designers to understand and merge priorities in order to inform the development of mobile learning (m-learning) applications that maximise user experiences and hence learning opportunities. It outlines a User Experience Design (UXD) theory and development process that requires designers to conduct a thorough initial contextual inquiry into a particular domain in order to set project priorities and development guidelines. A matrix that identifies the key contextual considerations namely the social, cultural, spatial, technical and temporal constructs of any domain is presented as a vital tool for achieving successful UXD. The frame of reference provided by this matrix ensures that decisions made throughout the design process are attributable to a desired user experience. To illustrate how the proposed UXD theory and development process supports the creation of effective m-learning applications, this paper documents the development process of MILK (Mobile Informal Learning Kit). MILK is a support tool that allows teachers and students to develop event paths that consist of a series SMS question and answer messages that lead players through a series of checkpoints between point A and point B. These event paths can be designed to suit desired learning scenarios and can be used to explore a particular place or subject. They can also be designed to facilitate formal or informal learning experiences.