A methodology for current density calculations in high-frequency RF resonators

As nuclear magnetic resonance imaging and spectroscopy move inexorably toward higher field-strength magnets in search of improved signal-to-noise ratio, spectral resolution, and spatial resolution, the way in which radiofrequency (RF) probes are designed changes. At higher frequencies, resonant cavities become the favored RF ''coil'' type and may be built using streamline elements to reduce the inductance of the system. In modeling such systems, the quasi-static approach of assuming that current flows evenly in all conductor cross sections and that adjacent conductors do not affect each other becomes less reasonable. The proximity of RF conductors in resonators typically causes RF eddy currents to flow, whereby the current density in each rung is altered by the RF fields generated by nearby conductors. The proper understanding and prediction of how resonators will perform require a model of the current densities flowing in conducting sections, including all RF eddy current effects. Very few models of this type have been presented in the literature. This article presents an overview of one such model and of how it may be applied to a variety of resonators, both shielded and unshielded, circular, and elliptical, in cross section. Results are presented from a shielded head coil operating at 2 tesla. (C) 1997 John Wiley & Sons, Inc.

Chemical characterization of soils of a tropical humid forest zone: A methodology

A methodology, based on a combination of routinely performed analyses and investigation of fundamental charge and anion sorption properties, was used to characterize the soils of the humid forest zone of Cameroon, In general, the soils have about 2 cmol kg(-1) permanent negative charge, with about 1 cmol kg(-1) from variable-charge sources at current soil pH values, Furthermore, they are impoverished with respect to Ca, Mg, and K, while Al frequently dominates the exchange complex. Thus, the ability of these soils to retain base cations is more limited than is suggested by the cation-exchange capacity (CEC), Therefore we propose the concept of a degradation index (DI) defined as: DI = 100(CEC5.5 - sum of basic cations)/CEC5.5, where CEC5.5 is the CEC measured at pH 5.5, This index encompasses degradation a soil may have experienced from natural or man-made causes, Extractable PO4 concentrations are considered very low and the soils have a moderate to high capacity to fix added PO4. Surface soil SO4 concentrations are considered marginal to deficient for plant growth, though adequate reserves of SO4 are held in the subsoil by SO4 sorption, The approach used demonstrated that the five morphologically different soil profile classes identified in the zone have similar chemical characteristics. Thus, the results of experimentation conducted on one of the soil profile classes will be applicable throughout the zone, Furthermore, the approach has provided a means of identifying comparable soil types in other parts of the world and will guide technology transfer, The analytical methods used in this study are relatively simple and require no specialized equipment, and are therefore within the capabilities of many laboratories in the developing world.

GP5+/6+ SYBR Green methodology for simultaneous screening and quantification of human papillomavirus

Background: Detection and quantification of human papillomavirus (HPV) may help in predicting the evolution of HPV infection and progression of associated lesions. Objectives: We propose a novel protocol using consensus primers GP5+/6+ in a SYBR Green quantitative real-time (Q-RT) polymerase chain reaction (PCR). The strategy permits screening for HPV infection and viral load quantification simultaneously. Study design: DNA from 153 archived cervical samples, previously tested for HPV detection by GP5+/6+ PCR and typed by EIA-RLB (enzyme immunoassay-reverse line blot) or sequence analysis, was analysed using SYBR Green Q-RT PCR. Melting temperature assay (T(m)) and cycle threshold (C(t)) were used to evaluate HPV positivity and viral load. The T(m) in the range of 77-82 degrees C was considered to be positive for HPV-DNA. HPV results generated through GP5+/6+ conventional PCR were considered the gold standard against which sensitivity and specificity of our assay were measured. Results: Out of 104 HPV positive samples, 100 (96.2%) were also determined as positive by SYBR Green Q-RT PCR; of the 49 HPV-negative samples, all were determined as negative. There was an excellent positivity agreement (K = 0.94) between the SYBR Green Q-RT and the previous methods employed. The specificity and sensitivity were 100% and 96.2%, respectively. Comparison of SYBR Green Q-RT and TaqMan oligo-probe technologies gave an excellent concordance (pc = 0.95) which validated the proposed strategy. Conclusions: We propose a sensitive and easy-to-perform technique for HPV screening and viral load quantification simultaneously. (C) 2009 Elsevier B.V. All rights reserved.

Domestic objects and the taste epiphany - A resource for consumption methodology

The presentation of an aesthetic identity involves the accomplishment of a coherent, plausible narrative which links one's choices to desired characteristics of the self. As symbolic evidence of a person's taste, material culture is a vital component of a successful narrative. Via case studies of pivotal household objects, this paper uses face-to-face interview data as a way of investigating processes of aesthetic choice. Household objects are interpreted as material elements imbricated in the presentation of a socially plausible and internally consistent aesthetic self. Narrative analysis, and the concept of the epiphany-object, are proposed as useful ways of accounting for tastes in domestic material culture. Methodological questions of truth-telling and authenticity in the face-to-face context are considered, and the sociological problem of taste is scrutinized in light of ideas about social accountability and textual identity.

Model based procedure for scale-up of wet overflow ball mills Part 1: Outline of the methodology

Bond's method for ball mill scale-up only gives the mill power draw for a given duty. This method is incompatible with computer modelling and simulation techniques. It might not be applicable for the design of fine grinding ball mills and ball mills preceded by autogenous and semi-autogenous grinding mills. Model-based ball mill scale-up methods have not been validated using a wide range of full-scale circuit data. Their accuracy is therefore questionable. Some of these methods also need expensive pilot testing. A new ball mill scale-up procedure is developed which does not have these limitations. This procedure uses data from two laboratory tests to determine the parameters of a ball mill model. A set of scale-up criteria then scales-up these parameters. The procedure uses the scaled-up parameters to simulate the steady state performance of full-scale mill circuits. At the end of the simulation, the scale-up procedure gives the size distribution, the volumetric flowrate and the mass flowrate of all the streams in the circuit, and the mill power draw.

A methodology for analysis of sugarcane productivity trends - I. Analysis across districts

Historically, few articles have addressed the use of district level mill production data for analysing the effect of varietal change on sugarcane productivity trends. This appears to be due to lack of compiled district data sets and appropriate methods by which to analyse these data. Recently, varietal data on tonnes of sugarcane per hectare (TCH), sugar content (CCS), and their product, tonnes of sugar content per hectare (TSH) on a district basis, have been compiled. This study was conducted to develop a methodology for regular analysis of such data from mill districts to assess productivity trends over time, accounting for variety and variety x environment interaction effects for 3 mill districts (Mulgrave, Babinda, and Tully) from 1958 to 1995. Restricted maximum likelihood methodology was used to analyse the district level data and best linear unbiased predictors for random effects, and best linear unbiased estimates for fixed effects were computed in a mixed model analysis. In the combined analysis over districts, Q124 was the top ranking variety for TCH, and Q120 was top ranking for both CCS and TSH. Overall production for TCH increased over the 38-year period investigated. Some of this increase can be attributed to varietal improvement, although the predictors for TCH have shown little progress since the introduction of Q99 in 1976. Although smaller gains have been made in varietal improvement for CCS, overall production for CCS decreased over the 38 years due to non-varietal factors. Varietal improvement in TSH appears to have peaked in the mid-1980s. Overall production for TSH remained stable over time due to the varietal increase in TCH and the non-varietal decrease in CCS.

A methodology for discipline-specific curriculum development

A methodology and framework for discipline-specific curriculum development in a local context is described. These activities, as part of the Thailand-Australia Science and Engineering Assistance Project, were in response to a needs analysis for curriculum assistance to a number of publicly-funded Thai universities in the engineering priority area of Materials Processing and Manufacturing. The paper outlines a strategy for the delivery of a centralised curriculum development workshop for academic staff follow-up visits and local curriculum activities with participating universities, and the presentation of technical short courses as guidance for such activity in other settings and/or discipline areas. This paper is part of a process of documentation so that others can apply the developed methodology and framework for curriculum development. While the paper is a report on curriculum activities in a particular setting, it is written in a manner that allows application of the methodology to other settings. The reader is advised that each curriculum activity needs to adopt a methodology and strategy to fit the particular circumstances being considered To assist in applying this approach elsewhere, a description of the various steps in the curriculum process, and typical responses to some of the more global issues, have been presented. Full details are available in the various TASEAP reports prepared by the authors. Specific detail has been omitted where this detail does not provide any information for generalized consumption.

Detection of swallowing sounds: Methodology revisited

Cervical auscultation is in the process of gaining clinical credibility. In order for it to be accepted by the clinical community, the procedure and equipment used must first be standardized. Takahashi et al. [Dysphagia 9:54-62, 1994] attempted to provide benchmark methodology for administering cervical auscultation. They provided information about the acoustic detector unit best suited to picking up swallowing sounds and the best cervical site to place it. The current investigation provides contrasting results to Takahashi et al. with respect to the best type of acoustic detector unit to use for detecting swallowing sounds. Our study advocates an electret microphone as opposed to an accelerometer for recording swallowing sounds. However, we agree on the optimal placement site. We conclude that cervical auscultation is within reach of the average dysphagia clinic.