Microcystin-LR detection in water by the Fabry–Pérot interferometer using an optical fibre coated with a sol–gel imprinted sensing membrane

Cyanobacteria deteriorate the water quality and are responsible for emerging outbreaks and epidemics causing harmful diseases in Humans and animals because of their toxins. Microcystin-LR (MCT) is one of the most relevant cyanotoxin, being the most widely studied hepatotoxin. For safety purposes, the World Health Organization recommends a maximum value of 1 μg L−1 of MCT in drinking water. Therefore, there is a great demand for remote and real-time sensing techniques to detect and quantify MCT. In this work a Fabry–Pérot sensing probe based on an optical fibre tip coated with a MCT selective thin film is presented. The membranes were developed by imprinting MCT in a sol–gel matrix that was applied over the tip of the fibre by dip coating. The imprinting effect was obtained by curing the sol–gel membrane, prepared with (3-aminopropyl) trimethoxysilane (APTMS), diphenyl-dimethoxysilane (DPDMS), tetraethoxysilane (TEOS), in the presence of MCT. The imprinting effect was tested by preparing a similar membrane without template. In general, the fibre Fabry–Pérot with a Molecular Imprinted Polymer (MIP) sensor showed low thermal effect, thus avoiding the need of temperature control in field applications. It presented a linear response to MCT concentration within 0.3–1.4 μg L−1 with a sensitivity of −12.4 ± 0.7 nm L μg−1. The corresponding Non-Imprinted Polymer (NIP) displayed linear behaviour for the same MCT concentration range, but with much less sensitivity, of −5.9 ± 0.2 nm L μg−1. The method shows excellent selectivity for MCT against other species co-existing with the analyte in environmental waters. It was successfully applied to the determination of MCT in contaminated samples. The main advantages of the proposed optical sensor include high sensitivity and specificity, low-cost, robustness, easy preparation and preservation.

Development of a thermoelectric generator for the exhaust of a vehicle

Dissertação de mestrado integrado em Engenharia Mecânica

Estudo de revestimentos ativos para o isolamento térmico de edifícios

Dissertação de mestrado em Sustentabilidade do Ambiente Construído

Regulation of the Gac/Rsm pathway in "Pseudomonas fluorescens" CHA0

SUMMARY : Two-component systems are key mediators implicated in the response of numerous bacteria to a wide range of signals and stimuli. The two-component system comprised of the sensor kinase GacS and the response regulator GacA is broadly distributed among γ-proteobacteria bacteria and fulfils diverse functions such as regulation of carbon storage and expression of virulence. In Pseudomonas fluorescens, a soil bacterium which protects plants from root-pathogenic fungi and nematodes, the GacS/GacA two-component system has been shown to be essential for the production of secondary metabolites and exoenzymes required for the biocontrol activity of the bacterium. The regulatory cascade initiated by GacS/GacA consists of two translational repressor proteins, RsmA and RsmE, as well as three GacAcontrolled small regulatory RNAs RsmX, RsmY and RsmZ, which titrate RsmA and RsmE to allow the expression of biocontrol factors. Genetic analysis revealed that two additional sensor kinases termed RetS and Lads were involved as negative and positive control elements, respectively, in the Gac/Rsm pathway in P. fluoresens CHAO. Furthermore, it could be proposed that RetS and Lads interact with GacS, thereby modulating the expression of antibiotic compounds and hydrogen cyanide, as well as the rpoS gene encoding the stress and stationary phase sigma factor σ. Temperature was found to be an important environmental cue that influences the Gac/Rsm network. Indeed, the production of antibiotic compounds and hydrogen cyanide was reduced at 35°C, by comparison with the production at 30°C. RetS was identified to be involved in this temperature control. The small RNA RsmY was confirmed to be positively regulated by GacA and RsmA/RsmE. Two essential regions were identified in the rsmY promoter by mutational analysis, the upstream activating sequence (UAS) and the linker sequence. Although direct experimental evidence is still missing, several observations suggest that GacA may bind to the UAS, whereas the linker region would be recognized by intermediate RsmA/RsmEdependent repressors and/or activators. In conclusion, this work has revealed new elements contributing to the function of the signal transduction mechanisms in the Gac/Rsm pathway. RESUME : Les systèmes ä deux composants sont des mécanismes d'une importance notoire que beaucoup de bactéries utilisent pour faire face et répondre aux stimuli environnementaux. Le système à deux composants comprenant le senseur GacS et le régulateur de réponse GacA est très répandu chez les γ-protéobactéries et remplit des fonctions aussi diverses que la régulation du stockage de carbone ou l'expression de la virulence. Chez Pseudomonas fluorescens CHAO, une bactérie du sol qui protège les racines des plantes contre des attaques de champignons et nématodes pathogènes, le système à deux composants GacS/GacA est essentiel à la production de métabolites secondaires et d'exoenzymes requis pour l'activité de biocontrôle de la bactérie. La cascade régulatrice initiée pas GacS/GacA fait intervenir deux protéines répresseur de traduction, RsmA et RsmE, ainsi que trois petits ARNs RsmX, RsmY et RsmZ, dont la production est contrôlée par GacA. Ces petits ARNs ont pour rôle de contrecarrer l'action des protéines répressseur de la traduction, ce qui permet l'expression de facteurs de biocontrôle. Des analyses génétiques ont révélé la présence de deux senseurs supplémentaires, appelés Rets et Lads, qui interviennent dans la cascade Gac/Rsm de P. fluorescens. L'impact de ces senseurs est, respectivement, négatif et positif. Ces interactions ont apparenunent lieu au niveau de GacS et permettent une modulation de l'expression des antibiotiques et de l'acide cyanhydrique, ainsi que du gène rpoS codant pour le facteur sigma du stress. La température s'est révélée être un facteur environnemental important qui influence la cascade Gac/Rsm. Il s'avère en effet que la production d'antibiotiques ainsi que d'acide cyanhydrique est moins importante à 35°C qu'à 30°C. L'implication du senseur Rets dans ce contrôle par la température a pu être démontrée. La régulation positive du petit ARN RsmY par GacA et RsmA/RsmE a pu être confirmée; par le biais d'une analyse mutationelle, deux régions essentielles ont pu être mises en évidence dans la région promotrice de rsmY. Malgré le manque de preuves expérimentales directes, certains indices suggèrent que GacA puisse directement se fixer sur une des deux régions (appelée UAS), tandis que la deuxième région (appelée linker) serait plutôt reconnue par des facteurs intermédiaires (activateurs ou répresseurs) dépendant de RsmA/RsmE. En conclusion, ce travail a dévoilé de nouveaux éléments permettant d'éclairer les mécanismes de transduction des signaux dans la cascade Gac/Rsm.

Recycling of Asphalt Concrete From I-80 in Cass County, HR-1011, 1978

Approximately 40,000 tons of deteriorated asphalt concrete has been removed from Interstate 80 in Cass County and stockpiled. Laboratory tests indicate that this material has considerable value when upgraded with new aggregate and asphalt cement. This report documents the procedures used and results obtained on an experimental recycling project. It was demonstrated that present drum mixing-recycling equipment and procedures can be used to utilize this material with satisfactory results. Laboratory analyses of material components and mixtures were performed; these analyses indicate mixture can be produced that is uniform, stable, and very closely resembles mixture produced with all virgin material. A 1700 foot long test section was constructed on US 169 in Kossuth County wherein salvaged asphalt concrete from I-80 in Cass County was utilized. The salvaged mix was blended with virgin aggregate and recycled through a modified drum mixing plant, the reprocessed mixture was satisfactorily placed 1 1/2 inches thick as a resurfacing course on an old PCC pavement. An inspection of the test section was made in December of 1978 to evaluate the performance after one full year of service. There was no evidence of rutting or shoving from traffic. The surface does, however, have a very dry and somewhat ravelled appearance. This can be related to a low asphalt content in the mix and some temperature control problems which were difficult to get fully corrected on such a short project and with a short supply of readily available materials.

Principal components analysis for quality evaluation of cooled banana 'Nanicão' in different packing

This work aims determinate the evaluation of the quality of 'Nanicão' banana, submitted to two conditions of storage temperature and three different kinds of package, using the technique of the Analysis of Principal Components (ACP), as a basis for an Analysis of Variance. The fruits used were 'Nanicão' bananas, at ripening degree 3, that is, more green than yellow. The packages tested were: "Torito" wood boxes, load capacity: 18 kg; "½ box" wood boxes, load capacity: 13 kg; and cardboard boxes, load capacity: 18 kg. The temperatures assessed were: room temperature (control); and (13±1ºC), with humidity controlled to 90±2,5%. Fruits were discarded when a sensory analysis determined they had become unfit for consumption. Peel coloration, percentages of imperfection, fresh mass, total acidity, pH, total soluble solids and percentages of sucrose were assessed. A completely randomized design with a 2-factorial treatment structure (packing X temperature) was used. The obtained data were analyzed through a multivariate analysis known as Principal Components Analysis, using S-plus 4.2. The conclusion was that the best packages to preserve the fruit were the ½ box ones, which proves that it is necessary to reduce the number of fruits per package to allow better ventilation and decreases mechanical injuries and ensure quality for more time.

SC HIOMON JA PAPERIKONEEN LÄMPÖTASAPAINON HALLINTA

Kivihiokkeen valmistus on energiaintensiivistä. Käytetystä energiasta muuttuu yli 90 prosenttia lämmöksi. Hiomolla käytetystä lämmöksi muuttuneesta tehosta voidaan paperikoneelle siirtää noin puolet. Mekaanisen massan valmistuksen ja paperikoneen vesikierrot erotetaan toisistaan häiriöaineiden kulkeutumisen estämiseksi. Vesikiertojen erottamisella katkaistaan myös lämmön siirtyminen hiomolta paperikoneelle massojen mukana. Käyttämällä lämmönsiirtimiä hiomon vesien jäähdytyksessä, voidaan hiomon hiomakoneiden suihkuvesivesilämpötilaa alentaa. Lämmönsiirto vaikuttaa paperikoneella annostelumassojen laimennusten kautta perälaatikkolämpötilaa kohottavasti. Työn tehtäväksi määritettiin kesäkuukausina esiintyvä hiomakoneiden suihkuveden raakavesijäähdytyksen tarpeen poistaminen ensisijaisesti niin, että ylimäärälämpö hyödynnetään tehtaalla. Työn muiksi tavoitteiksi muodostui annostelumassojen lämpötilan hallinta, etenkin muutokset, joilla voidaan nostaa hylkymassan annostelulämpötilaa. Työn kokeellinen osa tehtiin UPM Kymmene Oyj Kajaanin tehtailla syksyn 2004 aikana. Työssä tutkittiin WinGEMS simulointiohjelmalla tehtyjen mallien avulla lämmön siirtymistä hiomon ja paperikone 2:n välillä, sekä lämmönsiirtoa pois tasealueelta. Simulointimalli nykytilanteesta rakennettiin yksityiskohtaisesti nykyisen tuotantoprosessin kaltaiseksi ja siitä muokattiin eri vaihtoehtoja, joilla ratkaistiin tutkimukselle asetetut tehtävät. Kytkentämuutoksilla pystyttiin siirtämään hiomolta yli 85 % hiomakoneiden suihkuveden ylimäärälämmöstä ilman uusia laitehankintoja. Asentamalla lopuksi lämmönsiirrin hiomon puhdassuodoslinjaan, hiomakoneiden suihkuveden jäähdytystarve poistettiin kokonaan. Samalla alennettiin valkaisuun menevän massan lämpötilaa, jolloin peroksidivalkaisun kemikaalikulutus väheni yli 10 %. Lämmönsiirrinverkostosta tehtiin kesätilanteen pinch-analyysi, jolla selvitettiin prosessin lämmitys ja jäähdytystarpeet. Analyysin perusteella selvisi, että kytkennöissä ei rikota pinch sääntöjä ja, että prosessissa esiintyy kynnysongelma, jossa prosessi tarvitsee ainoastaan jäähdytystä.

Monitoring the viability of citrus rootstocks seeds stored under refrigeration

The citrus nursery tree is produced through the bud grafting process, in which rootstock is usually grown from seed germination. The objective of this research was to evaluate, in two dissimilar environmental conditions, the viability and polyembryony expression of five citrus rootstocks seeds stored in different periods under refrigeration. The rootstock varieties evaluated were: Rangpur lime (Citrus limonia Osb. cv. Limeira), Trifoliate orange (Poncirus trifoliata Raf. cv. Limeira), Citrumelo (P. trifoliata x C. paradisi Macf. cv. Swingle), Sunki mandarin (C. sunki Hort. ex Tanaka) and Volkamer lemon (C. volkameriana Ten. & Pasq. cv. Catania 2). The experimental design was the randomized blocks in a 11 x 5 x 2 factorial scheme, evaluating from time zero to the tenth month of storage, the five varieties of rootstock in two environments: germination and growth B.O.D type chamber (Biological Oxygen Demand - Eletrolab Brand Model FC 122) at 25 °C; and greenhouse seedbed with partial temperature control (22 °C to 36 °C) and humidity control (75-85%). The plot had 24 seeds in four replicates, using trays with substrate in greenhouse and Petri dishes with filter paper in B.O.D. chamber. The seed germination rate and polyembryony expression were evaluated monthly. It was concluded that Trifoliate and Citrumelo Swingle seeds can be stored for up to seven months, while Volkamer lemon, Rangpur lime and Sunki seeds can be stored for up to ten months. The polyembryony expression rate was slightly higher when measured in greenhouse than in B.O.D. chamber and remained stable in both environments until the seventh month, from which dropped sharply. Citrumelo Swingle seeds expressed the highest polyembryony rate (18.8%), followed by Rangpur lime and Volkamer lemon (average value of 13.7%), Sunki (9.4%) and Trifoliate (3.2%). Despite some differences among varieties, the viability of rootstock stored seeds can be monitored either in the greenhouse or in B.O.D. germination chamber, the latter being the faster and more suitable method.

Cooling system optimization in medium-speed engines

Tässä työssä optimoidaan keskinopean Wärtsilä 32 -dieselmoottorin jäähdytysjärjestelmää ja tutkitaan taajuusmuuttajien käyttömahdollisuutta kiertopumppujen yhteydessä niin, että järjestelmässä saataisiin kiertämään vain kulloinkin tarvittava määrä vettä. Tutkimuksen mallinnus on toteutettu laatimalla aiemmin käytössä olleista yksinkertaisista simulointimalleista yksi malli, johon on sisällytetty sekä virtauksen että lämmönsiirron laskenta, jotka on aiemmin mallinnettu erillisillä ohjelmilla. Diplomityö on osa projektia, joka on tehty Sähkötekniikan osaston tutkijan Mikko Pääkkösen kanssa yhteistyössä. Tämän diplomityö keskittyy lähinnä virtausteknisiin ja lämmönsiirtoon liittyviin asioihin, kun taas sähkötekniikan osuus on esitetty Mikko Pääkkösen raportissa. Tulosten perustella voidaan sanoa, että taajuusmuuttajakäyttö kannattaa kiertopumppujen yhteydessä. Käyttämällä pumppujen virtaussäätöä voidaan jäähdytysjärjestelmästä jättää monia komponentteja, kuten termostaattiventtiilejä pois. Mallinnetut yksinkertaiset piiriratkaisut näyttävät toimivan ainakin yleisellä tasolla. Tutkimusta pumppujen säädöstä ja tässä projektissa luoduista jäähdytysjärjestelmäkonfiguraatioista kannattaa jatkaa.

Construcció d'un equip per a la producció de cervesa artesana

Catalunya és un dels territoris on hi ha hagut més auge del sector de la cervesa artesana, i són molt nombroses les microcerveseries i les botigues especialitzades on es poden trobar els recursos materials necessaris, a més de ser centres difusió de coneixements relacionats. Així, doncs, aquest projecte està emmarcat en un context que permet el desenvolupament de tècniques d’elaboració de cervesa artesana. Aquest projecte es basa en la construcció d’un equip amb materials reutilitzats i amb un pressupost limitat que permet reproduir a petita escala els processos d’elaboració que es duen a terme en les microcerveseries artesanes actuals. El projecte s’ha assentat sobre la comprensió dels fonaments teòrics i pràctics del procés d’elaboració de cervesa, i amb l’experiència inicial d’elaboració de cervesa amb un equip bàsic de tipus homebrewer. Per minimintzar costos els tancs s’han construït a partir de barrils de cervesa i les parts sobrants s’han aprofitat per a altres elements. S’han emprat elements quotidians com una olla a pressió i s’ha construït un sistema regulador de pressió (per al tanc de fermentació cilindrocònic isobàric construït) en lloc d’adquirir-lo. S’ha posat l’èmfasi en minimitzar la necessitat de manipulació manual durant l’elaboració. Per tant, s’han instal·lat els components de l’equip formant un circuit tancat amb sistema de bombeig, i s’ha incorporat un sistema que permet el control i la lectura de les temperatures de cada procés. Altres elements són el sistema de filtres amb mecanisme de tub en forma d’ela (que permet l’extracció del most dels tanc de maceració i de cocció d’una manera efectiva i sense necessitat de manipulació) i el sistema de dutxa (que permet automatitzar el procés de rentat i filtrat). Un element que distingeix aquest equip d’altres equips emprats en algunes microcerveseries artesanes és el tanc de fermentació cilindrocònic isobàric amb vàlvula controladora de pressió, que permet prescindir de la doble fermentació en ampolla, ja que permet aprofitar el gas carbònic produït durant la fermentació per la carbonatació de la cervesa. Es pot concloure que gràcies a les seves característiques, l’equip permet realitzar successives elaboracions obtenint el mateix producte amb les mateixes característiques organolèptiques, principalement gràcies a la cambra de fermentació, que permet realitzar les etapes de fermentació, maduració i clarificació controlant la temperatura desitjada; al tanc de maceració amb aïllament, que permet realitzar el procés a temperatura constant sense pèrdues tèrmiques i al sistema de control de temperatura de totes les etapes. L’únic inconvenient és que, degut a la manca pressupostària, ha estat impossible l’adquisició d’un sistema d’embotellament isobàric que permeti realitzar l’embotellament sense pèrdues del gas carbònic. Per tant, el producte final pot embotellar-se amb una lleugera pèrdua de gas o es pot emmagatzemar en el mateix fermentador cilindrocònic per al seu consum directe, a l’estil d’alguns brewpubs.

Construção de uma célula espectroeletroquímica termostatizada e sua aplicação para estudar polímeros eletrocrômicos

The construction of a temperature controllable spectroelectrochemical cell is described. Its use in the analysis of the thermodynamic and structural parameters of the electrochromic process of poly(3-methyl thiophene) in the temperature range between -40ºC and 60ºC is given as an example of application.

Kaksiakselisen välijäähdytyksellä, välipoltolla ja rekuperaattorilla varustetun mikrokaasuturbiinin osakuormahyötysuhteen säilyvyyden optimointi

Työssä pyrittiin etsimään differentiaalievoluutioalgoritmilla kaksiakseliselle, välijäähdytyksellä, välipoltolla ja rekuperaattorilla varustetulle mikrokaasuturbiinille sellaiset kompressorien painesuhteet ja rekuperaattorin rekuperaatioaste, että saavutettaisiin mandollisimman hyvä osakuormahyötysuhteen säilyvyys. Osakuormatehon säätömenetelmäksi oli valittu pyörimisnopeussäädön ja turbiinien sisääntulolämpötilan alentamisen yhdistelmä, jossa generaattorilla varustetun akselin pyörimisnopeus sekä molempien turbiinien sisääntulolämpötilat olivat toisistaan riippumatta vapaasti säädettävissä. Työssä löydettiin optimaalinen säätömenetelmien yhdistelmä, jolla saavutetaan parempi osakuormahyötysuhteen säilyvyys, kuin millään käytetyistä menetelmistä yksinään. Lisäksi havaittiin, ettei optimaalinen säätömenetelmä merkittävästi riipu koneikolle valituista suunnittelupisteen parametreista. Osakuormahyötysuhteen säilyvyyden kannalta optimaalinen koneikko ei merkittävästi poikennut suunnittelupisteen hyötysuhteen kannalta optimaalisesta.

Medidas de tensão superficial pelo método de contagem de gotas: descrição do método e experimentos com tensoativos não-iônicos etoxilados

Surface tension knowledge of surfactants aqueous solutions is important during amphiphilic molecule manufacturing and new product development, as feedback information to handle synthesis parameters to target performance. Drop counting method is an interesting simplification of drop weight method for surface tension measurements. A simple laboratory measurement device, with capability for temperature control, was assembled to allow investigation of ethoxylated surfactants. The implementation of the method was preceded by a detailed investigation of two factors that may affect the measured surface tension: drop formation velocity and surfactant ethoxylation degree. The limitations of the method are discussed on this basis.

Synthesis of percarboxylic acids in microreactor

Percarboxylic acids are commonly used as disinfection and bleaching agents in textile, paper, and fine chemical industries. All of these applications are based on the oxidative potential of these compounds. In spite of high interest in these chemicals, they are unstable and explosive chemicals, which increase the risk of synthesis processes and transportation. Therefore, the safety criteria in the production process should be considered. Microreactors represent a technology that efficiently utilizes safety advantages resulting from small scale. Therefore, microreactor technology was used in the synthesis of peracetic acid and performic acid. These percarboxylic acids were produced at different temperatures, residence times and catalyst i.e. sulfuric acid concentrations. Both synthesis reactions seemed to be rather fast because with performic acid equilibrium was reached in 4 min at 313 K and with peracetic acid in 10 min at 343 K. In addition, the experimental results were used to study the kinetics of the formation of performic acid and peracetic acid. The advantages of the microreactors in this study were the efficient temperature control even in very exothermic reaction and good mixing due to the short diffusion distances. Therefore, reaction rates were determined with high accuracy. Three different models were considered in order to estimate the kinetic parameters such as reaction rate constants and activation energies. From these three models, the laminar flow model with radial velocity distribution gave most precise parameters. However, sulfuric acid creates many drawbacks in this synthesis process. Therefore, a ´´greener´´ way to use heterogeneous catalyst in the synthesis of performic acid in microreactor was studied. The cation exchange resin, Dowex 50 Wx8, presented very high activity and a long life time in this reaction. In the presence of this catalyst, the equilibrium was reached in 120 second at 313 K which indicates a rather fast reaction. In addition, the safety advantages of microreactors were investigated in this study. Four different conventional methods were used. Production of peracetic acid was used as a test case, and the safety of one conventional batch process was compared with an on-site continuous microprocess. It was found that the conventional methods for the analysis of process safety might not be reliable and adequate for radically novel technology, such as microreactors. This is understandable because the conventional methods are partly based on experience, which is very limited in connection with totally novel technology. Therefore, one checklist-based method was developed to study the safety of intensified and novel processes at the early stage of process development. The checklist was formulated using the concept of layers of protection for a chemical process. The traditional and three intensified processes of hydrogen peroxide synthesis were selected as test cases. With these real cases, it was shown that several positive and negative effects on safety can be detected in process intensification. The general claim that safety is always improved by process intensification was questioned.

Thermal modelling of commercial lithium-ion batteries

The accelerating adoption of electrical technologies in vehicles over the recent years has led to an increase in the research on electrochemical energy storage systems, which are among the key elements in these technologies. The application of electrochemical energy storage systems for instance in hybrid electrical vehicles (HEVs) or hybrid mobile working machines allows tolerating high power peaks, leading to an opportunity to downsize the internal combustion engine and reduce fuel consumption, and therefore, CO2 and other emissions. Further, the application of electrochemical energy storage systems provides an option of kinetic and potential energy recuperation. Presently, the lithium-ion (Li-ion) battery is considered the most suitable electrochemical energy storage type in HEVs and hybrid mobile working machines. However, the intensive operating cycle produces high heat losses in the Li-ion battery, which increase its operating temperature. The Li-ion battery operation at high temperatures accelerates the ageing of the battery, and in the worst case, may lead to a thermal runaway and fire. Therefore, an appropriate Li-ion battery cooling system should be provided for the temperature control in applications such as HEVs and mobile working machines. In this doctoral dissertation, methods are presented to set up a thermal model of a single Li-ion cell and a more complex battery module, which can be used if full information about the battery chemistry is not available. In addition, a non-destructive method is developed for the cell thermal characterization, which allows to measure the thermal parameters at different states of charge and in different points of cell surface. The proposed models and the cell thermal characterization method have been verified by experimental measurements. The minimization of high thermal non-uniformity, which was detected in the pouch cell during its operation with a high C-rate current, was analysed by applying a simplified pouch cell 3D thermal model. In the analysis, heat pipes were incorporated into the pouch cell cooling system, and an optimization algorithm was generated for the estimation of the optimalplacement of heat pipes in the pouch cell cooling system. An analysis of the application of heat pipes to the pouch cell cooling system shows that heat pipes significantly decrease the temperature non-uniformity on the cell surface, and therefore, heat pipes were recommended for the enhancement of the pouch cell cooling system.