Análise tribo-termodinâmica da aplicação de nanopartículas de Al2O3 como aditivo lubrificante em compressor hermético de refrigeração

The thermodynamic performance of a refrigeration system can be improved by reducing the compression work by a particular technique for a specific heat removal rate. This study examines the effect of small concentrations of Al2O3 (50 nm) nanoparticles dispersion in the mineral oil based lubricant on the: viscosity, thermal conductivity, and lubrication characteristics as well as the overall performance (based on the Second Law of Thermodynamics) of the refrigerating system using R134a or R600a as refrigerants. The study looked at the influences of variables: i) refrigerant charge (100, 110, 120 and 130 g), ii) rotational speed of the condenser blower (800 and 1100 RPM) and iii) nanoparticle concentration (0.1 and 0.5 g/l) on the system performance based on the Taguchi method in a matrix of L8 trials with the criterion "small irreversibility is better”. They were carried pulldown and cycling tests according to NBR 12866 and NBR 12869, respectively, to evaluate the operational parameters: on-time ratio, cycles per hour, suction and discharge pressures, oil sump temperature, evaporation and condensation temperatures, energy consumption at the set-point, total energy consumption and compressor power. In order to evaluate the nanolubricant characteristics, accelerated tests were performed in a HFRR bench. In each 60 minutes test with nanolubricants at a certain concentration (0, 0.1 and 0.5 g/l), with three replications, the sphere (diameter 6.00 ± 0.05 mm, Ra 0.05 ± 0.005 um, AISI 52100 steel, E = 210 GPa, HRC 62 ± 4) sliding on a flat plate (cast iron FC200, Ra <0.5 ± 0.005 um) in a reciprocating motion with amplitude of 1 mm, frequency 20 Hz and a normal load of 1,96 N. The friction coefficient signals were recorded by sensors coupled to the HFRR system. There was a trend commented bit in the literature: a nanolubricant viscosity reduction at the low nanoparticles concentrations. It was found the dominant trend in the literature: increased thermal conductivity with increasing nanoparticles mass fraction in the base fluid. Another fact observed is the significant thermal conductivity growth of nanolubricant with increasing temperature. The condenser fan rotational speed is the most influential parameter (46.192%) in the refrigerator performance, followed by R600a charge (38.606%). The Al2O3 nanoparticles concentration in the lubricant plays a minor influence on system performance, with 12.44%. The results of power consumption indicates that the nanoparticles addition in the lubricant (0.1 g/L), together with R600a, the refrigerator consumption is reduced of 22% with respect to R134a and POE lubricant. Only the Al2O3 nanoparticles addition in the lubricant results in a consumption reduction of about 5%.

Empirical expression of tool wear when face milling 416 SS

During a machining process, cutting parameters must be taken into account, since depending on them the cutting edge starts to wear out to the point that tool can fail and needs to be change, which increases the cost and time of production. Since wear is a negative phenomenon on the cutting tool, due to the fact that tool life is reduced, it is important to optimize the cutting variables to be used during the machining process, in order to increase tool life. This research is focused on the influence of cutting parameters such as cutting speed, feed per tooth and axial depth of cut on tool wear during a face milling operation. The Taguchi method is applied in this study, since it uses a special design of orthogonal array to study the entire parameters space, with only few numbers of experiments. Also a relationship between tool wear and the cutting parameters is presented. For the studies, a martensitic 416 stainless steel was selected, due to the importance of this material in the machining of valve parts and pump shafts. Copyright © 2009 by ASME.

Otimização dos parâmetros de maquinagem no processo de fresagem

Cada vez mais, os principais objetivos na indústria é a produção a baixo custo, com a máxima qualidade e com o tempo de fabrico o mais curto possível. Para atingir esta meta, a indústria recorre, frequentemente, às máquinas de comando numérico (CNC), uma vez que com esta tecnologia torna se capaz alcançar uma elevada precisão e um tempo de processamento mais baixo. As máquinas ferramentas CNC podem ser aplicadas em diferentes processos de maquinagem, tais como: torneamento, fresagem, furação, entre outros. De todos estes processos, o mais utilizado é a fresagem devido à sua versatilidade. Utiliza-se normalmente este processo para maquinar materiais metálicos como é o caso do aço e dos ferros fundidos. Neste trabalho, são analisados os efeitos da variação de quatro parâmetros no processo de fresagem (velocidade de corte, velocidade de avanço, penetração radial e penetração axial), individualmente e a interação entre alguns deles, na variação da rugosidade num aço endurecido (aço 12738). Para essa análise são utilizados dois métodos de otimização: o método de Taguchi e o método das superfícies. O primeiro método foi utilizado para diminuir o número de combinações possíveis e, consequentemente, o número de ensaios a realizar é denominado por método de Taguchi. O método das superfícies ou método das superfícies de resposta (RSM) foi utilizado com o intuito de comparar os resultados obtidos com o método de Taguchi, de acordo com alguns trabalhos referidos na bibliografia especializada, o RSM converge mais rapidamente para um valor ótimo. O método de Taguchi é muito conhecido no setor industrial onde é utilizado para o controlo de qualidade. Apresenta conceitos interessantes, tais como robustez e perda de qualidade, sendo bastante útil para identificar variações do sistema de produção, durante o processo industrial, quantificando a variação e permitindo eliminar os fatores indesejáveis. Com este método foi vi construída uma matriz ortogonal L16 e para cada parâmetro foram definidos dois níveis diferentes e realizados dezasseis ensaios. Após cada ensaio, faz-se a medição superficial da rugosidade da peça. Com base nos resultados obtidos das medições da rugosidade é feito um tratamento estatístico dos dados através da análise de variância (Anova) a fim de determinar a influência de cada um dos parâmetros na rugosidade superficial. Verificou-se que a rugosidade mínima medida foi de 1,05m. Neste estudo foi também determinada a contribuição de cada um dos parâmetros de maquinagem e a sua interação. A análise dos valores de “F-ratio” (Anova) revela que os fatores mais importantes são a profundidade de corte radial e da interação entre profundidade de corte radial e profundidade de corte axial para minimizar a rugosidade da superfície. Estes têm contribuições de cerca de 30% e 24%, respetivamente. Numa segunda etapa este mesmo estudo foi realizado pelo método das superfícies, a fim de comparar os resultados por estes dois métodos e verificar qual o melhor método de otimização para minimizar a rugosidade. A metodologia das superfícies de resposta é baseada num conjunto de técnicas matemáticas e estatísticas úteis para modelar e analisar problemas em que a resposta de interesse é influenciada por diversas variáveis e cujo objetivo é otimizar essa resposta. Para este método apenas foram realizados cinco ensaios, ao contrário de Taguchi, uma vez que apenas em cinco ensaios consegue-se valores de rugosidade mais baixos do que a média da rugosidade no método de Taguchi. O valor mais baixo por este método foi de 1,03μm. Assim, conclui-se que RSM é um método de otimização mais adequado do que Taguchi para os ensaios realizados. Foram obtidos melhores resultados num menor número de ensaios, o que implica menos desgaste da ferramenta, menor tempo de processamento e uma redução significativa do material utilizado.

Projeto de experimentos em rodas ferroviárias fundidas em aço, com o uso da técnica de Taguchi

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Melhoria da qualidade de um processo de usinagem utilizando as técnicas de avaliação de Taguchi

Delivering to the customers a product or service with the expected quality associated to the huge competitiveness that exists in the market nowadays, has been making organizations increasingly focus on quality planning using techniques which are directed towards the continuous improvement process and production optimization. Thus, this paper aims to improve a machining process using the techniques of experimental design to the optimization and this also includes the analysis of the measurement system. For this purpose, the alloy Nimonic 80A, a nickel base superalloy, was used in the process due to its widespread use for high temperatures, applying this study the robust method proposed by Genichi Taguchi, determining the influence of the factors considered input variables, cutting speed, feed rate, depth of cut, type of tool, lubrication, and material hardness, in the output or response variable, surface roughness, concluding with the use of Taguchi orthogonal array L16 and by analysis of ANOVA that the factor feed rate is significant and offers greater effect on the response variable studied, should be set to 0,12mm/rev. Moreover, the factor type of tool has more influence on the process when compared to other factors, being CP250 the one more suitable to the process. Lastly, the interaction feed rate x cutting speed provides greater significance in the process regarding to surface roughness variable, being the best match between them 0,12mm/rev to the feed rate and 90m/min to the cutting speed. In order to evaluate the measurement system, it was applied the repeatability and reproducibility method (R&R), through which we saw that the system needs improvement (R & R = 88.04% >>> 30%) as the value found in the study was well above compared to the one that classifies the system as inappropriate

Treatment of rice straw hemicellulosic hydrolysates with advanced oxidative processes: a new and promising detoxification method to improve the bioconversion process

Abstract Background The use of lignocellulosic constituents in biotechnological processes requires a selective separation of the main fractions (cellulose, hemicellulose and lignin). During diluted acid hydrolysis for hemicellulose extraction, several toxic compounds are formed by the degradation of sugars and lignin, which have ability to inhibit microbial metabolism. Thus, the use of a detoxification step represents an important aspect to be considered for the improvement of fermentation processes from hydrolysates. In this paper, we evaluated the application of Advanced Oxidative Processes (AOPs) for the detoxification of rice straw hemicellulosic hydrolysate with the goal of improving ethanol bioproduction by Pichia stipitis yeast. Aiming to reduce the toxicity of the hemicellulosic hydrolysate, different treatment conditions were analyzed. The treatments were carried out according to a Taguchi L16 orthogonal array to evaluate the influence of Fe+2, H2O2, UV, O3 and pH on the concentration of aromatic compounds and the fermentative process. Results The results showed that the AOPs were able to remove aromatic compounds (furan and phenolic compounds derived from lignin) without affecting the sugar concentration in the hydrolysate. Ozonation in alkaline medium (pH 8) in the presence of H2O2 (treatment A3) or UV radiation (treatment A5) were the most effective for hydrolysate detoxification and had a positive effect on increasing the yeast fermentability of rice straw hemicellulose hydrolysate. Under these conditions, the higher removal of total phenols (above 40%), low molecular weight phenolic compounds (above 95%) and furans (above 52%) were observed. In addition, the ethanol volumetric productivity by P. stipitis was increased in approximately twice in relation the untreated hydrolysate. Conclusion These results demonstrate that AOPs are a promising methods to reduce toxicity and improve the fermentability of lignocellulosic hydrolysates.

An approximate method for the solution of an influence function foil rolling model

Fleck and Johnson (Int. J. Mech. Sci. 29 (1987) 507) and Fleck et al. (Proc. Inst. Mech. Eng. 206 (1992) 119) have developed foil rolling models which allow for large deformations in the roll profile, including the possibility that the rolls flatten completely. However, these models require computationally expensive iterative solution techniques. A new approach to the approximate solution of the Fleck et al. (1992) Influence Function Model has been developed using both analytic and approximation techniques. The numerical difficulties arising from solving an integral equation in the flattened region have been reduced by applying an Inverse Hilbert Transform to get an analytic expression for the pressure. The method described in this paper is applicable to cases where there is or there is not a flat region.

A Petrov-Galerkin method for a singularly perturbed ordinary differential equation with non-smooth data

In this paper, a singularly perturbed ordinary differential equation with non-smooth data is considered. The numerical method is generated by means of a Petrov-Galerkin finite element method with the piecewise-exponential test function and the piecewise-linear trial function. At the discontinuous point of the coefficient, a special technique is used. The method is shown to be first-order accurate and singular perturbation parameter uniform convergence. Finally, numerical results are presented, which are in agreement with theoretical results.