Theory and application of electrical engineering.

Includes bibliographies.

Electrical engineering; the engineering journal of the electrical industry.

Vols. 2 and 4 include supplements "The Manchester electrical exhibition of 1908" and "The electrical exhibition of 1911", respectively, each issued in 5 parts.

Contribution from the Dept. of Electrical Engineering.

Reprinted in part from various scientific serials.

Discussion of the precision of measurements : with examples taken mainly from physics and electrical engineering /

Advertising section at the end of the book.

A functional description of the Edvac [an automatically-sequence serial binary electronic digital computer. Final report of work under contract W36-034-ORD-7593 between the Ordinance Department, Department of the Army and the University of Pennsylvania, Moore School of Electrical Engineering.

Errata, as of Apr. 1, 1950 (7 ¹., 2 diagrs.) inserted.

Electrical Engineering Regulations

Mode of access: Internet.

The dynamic decode-and-forward channel: SNR allocation.

In the half-duplex relay channel applying the decode-and-forward protocol the relay introduces energy over random time intervals into the channel as observed at the destination. Consequently, during simulation the average signal power seen at the destination becomes known at run-time only. Therefore, in order to obtain specific performance measures at the signal-to-noise ratio (SNR) of interest, strategies are required to adjust the noise variance during simulation run-time. It is necessary that these strategies result in the same performance as measured under real-world conditions. This paper introduces three noise power allocation strategies and demonstrates their applicability using numerical and simulation results.

A touchless passive Infrared gesture sensor.

A sensing device for a touchless, hand gesture, user interface based on an inexpensive passive infrared pyroelectric detector array is presented. The 2 x 2 element sensor responds to changing infrared radiation generated by hand movement over the array. The sensing range is from a few millimetres to tens of centimetres. The low power consumption (< 50 μW) enables the sensor’s use in mobile devices and in low energy applications. Detection rates of 77% have been demonstrated using a prototype system that differentiates the four main hand motion trajectories – up, down, left and right. This device allows greater non-contact control capability without an increase in size, cost or power consumption over existing on/off devices.

CFAR Adaptive PN Code acquisition for DSSS Systems.

Constant false alarm rate (CFAR) techniques can be used in Pseudo-Noise (PN) code acquisition in Spread Spectrum (SS) communication systems, and all the CFAR techniques perform well in homogeneous background PN code acquisition. However, in non-homogeneous background, some CFAR techniques suffer rapid degradation. GO/SO (Greatest-of/Smallest-of) CFAR and adaptive censored mean level detector (ACMLD) are two adaptive CFAR techniques, which are analyzed and compared with other CFAR techniques. The simulation results show that GO/SO CFAR is superior to other CFAR techniques, it maintains short mean acquisition time (MAT) even at environment with strong clutter noise, and ACMLD is suitable for background with strong interfering targets

Mid-infrared photonic sensors based on metamaterial structures

In this work three different metallic metamaterials (MMs) structures such as asymmetric split ring resonators (A-SRRs), dipole and split H-shaped (ASHs) structures that support plasmonic resonances have been developed. The aim of the work involves the optimization of photonic sensor based on plasmonic resonances and surface enhanced infrared absorption (SEIRA) from the MM structures. The MMs structures were designed to tune their plasmonic resonance peaks in the mid-infrared region. The plasmonic resonance peaks produced are highly dependent on the structural dimension and polarisation of the electromagnetic (EM) source. The ASH structure particularly has the ability to produce the plasmonic resonance peak with dual polarisation of the EM source. The double resonance peaks produced due to the asymmetric nature of the structures were optimized by varying the fundamental parameters of the design. These peaks occur due to hybridization of the individual elements of the MMs structure. The presence of a dip known as a trapped mode in between the double plasmonic peaks helps to narrow the resonances. A periodicity greater than twice the length and diameter of the metallic structure was applied to produce narrow resonances for the designed MMs. A nanoscale gap in each structure that broadens the trapped mode to narrow the plasmonic resonances was also used. A thickness of 100 nm gold was used to experimentally produce a high quality factor of 18 in the mid-infrared region. The optimised plasmonic resonance peaks was used for detection of an analyte, 17β-estradiol. 17β-estradiol is mostly responsible for the development of human sex organs and can be found naturally in the environment through human excreta. SEIRA was the method applied to the analysis of the analyte. The work is important in the monitoring of human biology and in water treatment. Applying this method to the developed nano-engineered structures, enhancement factors of 10^5 and a sensitivity of 2791 nm/RIU was obtained. With this high sensitivity a figure of merit (FOM) of 9 was also achieved from the sensors. The experiments were verified using numerical simulations where the vibrational resonances of the C-H stretch from 17β-estradiol were modelled. Lastly, A-SRRs and ASH on waveguides were also designed and evaluated. These patterns are to be use as basis for future work.