Avaliação do desempenho do aço AISI D2 tratado termicamente e nitretado em plasma com gaiola catódica visando aplicação industrial

In the research, steel samples tool AISI D2, treated thermally, in the conditions: relief of tension, when maximum, seasoned and seasoned was treated thermally in the temperature of revenimento and revenida had been nitrited in plasma with cathodic cage, in atmosphere of 80%N2:20%H2. One used pressure of 2,5 mbar, 400 and 480°C temperatures with treatment time of 3 and 4 hours, with the objective to evaluate its performance in pipes cut tool. It was compared that the performance of the same steel when only thermally treated, both with tension relief. It was evaluated its hardness. Microstructural aspects (the layer thickness, interface, graisn size, etc) and crystalline phases on the surface. Besides, it was verified accomplishment possibility of nitriding simultaneous to annealing treatment. The tempering samples had presented hardness levels of 600 HV, while in nitrited samples these values had been 1100 HV

Influencia da Carga no Comportamento quanto ao Desgaste de um Aco ABNT-1020 Bifasico Revenido a 450°C

The wear rate of the dual-phase steel ABNT-1020 tempered at 450°C sliding against cemented steel ABNT-1020 in function of load value is investigated in wide load range. The alteration in behavior of this function at intermediate load level, like in the case of low hardness steel sliding against high hardness steel, is observed. The analysis by scanning electronic microscope before and after this alteration showed a change of wear mechanism from plastic displacement to embrittlement.

Microstructure evolution during warm deformation of low carbon steel with dispersed cementite

The microstructure evolution and mechanical behavior during large strain of a 0.16%C-Mn steel has been investigated by warm torsion tests. These experiments were carried out at 685°C at equivalent strain rate of 0.1 s . The initial microstructure composed of a martensite matrix with uniformly dispersed fine cementite particles was attained by quenching and tempering. The microstructure evolution during tempering and straining was performed through interrupted tests. As the material was reheated to testing temperature, well-defined cell structure was created and subgrains within lath martensite were observed by TEM; strong recovery took place, decreasing the dislocation density. After 1 hour at the test temperature and without straining, EBSD technique showed the formation of new grains. The flow stress curves measured had a peculiar shape: rapid work hardening to a hump, followed by an extensive flow-softening region. 65% of the boundaries observed in the sample strained to ε = 1.0 were high angle grain boundaries. After straining to ε = 5.0, average ferrite grain size close to 1.5 μm was found, suggesting that dynamic recrystallization took place. Also, two sets of cementite particles were observed: large particles aligned with straining direction and smaller particles more uniformly dispersed. The fragmentation or grain subdivision that occurred during reheating and tempering time was essential for the formation of ultrafine grained microstructure.

Efeito do tratamento térmico nas propriedades mecânicas e resistência ao desgaste de um ferro fundido branco multicomponente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Determinação da taxa de propagação de trinca por fadiga dos aços SAE-1050 e SAE-4130 empregados na fabricação de eixos ferroviários

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização de um aço microligado ao boro e tratado termicamente utilizado na fabricação de tubos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de tubo ARBL contendo 1Cr 0,2Mo fabricado pelo processo ERW/HF destinado à indústria de petróleo e gás

Pós-graduação em Engenharia Mecânica - FEG

Influência do raio de ponta do entalhe, do tipo de carregamento e da microestrutura no processo à fratura do aço estrutural ABNT-4340

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos dos tratamentos térmicos de normalização, resfriamento rápido e alívio de tensões no aço ASTM A-516 grau 70, utilizado na fabricação de vasos de pressão

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência do processamento térmico sobre as propriedades mecânicas e microestruturais de um aço XC48 aplicado a componentes automotivos visando atendimento ao projeto ULSAB

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos das microestruturas bainíticas e multifásicas nas propriedades mecânicas de um aço AISI 4340

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Projeto de experimentos e modelamento matemático do limite de resistência dos arames de aço SAE 9254 temperados e revenidos usados na fabricação de molas automobilísticas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Planejamento de experimentos em blocos aplicado às propriedades mecânicas de arames de aço para molas

The purpose of this article is to demonstrate an application of the design of block experiments via analysis and multiple linear regression in the investigation of a steel thermal treatment process with multiple responses. The study aimed to design statistical models to predict the mechanical properties in SAE 9254 draw steel wires, with diameters of 2.00 mm and 6.50 mm, after quench hardening and tempering. For this purpose, process input variables (wire diameter, processing speed, tempering temperature and polymer concentration) were investigated regarding their influence on the material tensile strength, yield point and hardness. The results revealed that the mechanical properties of the steel wire are significantly influenced by the selected variables, and analysis of variance (ANOVA) was employed to validate the design of the statistical models. Multiple linear regression allowed for an appropriate representation of the process, and graphical analysis was found to be very useful in displaying the behavior of the multiple responses.

Second Phase Precipitation in Ultrafine-grained Ferrite Steel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Modelagem e otimização por metodologia de superfícies de resposta: um estudo em arames de aço SAE 9254 para molas automobilísticas

Pós-graduação em Engenharia Mecânica - FEG