Fusion of Data from Quadcopter’s Inertial Measurement Unit Using Complementary Filter

A quadcopter is a helicopter with four rotors, which is mechanically simple device, but requires complex electrical control for each motor. Control system needs accurate information about quadcopter’s attitude in order to achieve stable flight. The goal of this bachelor’s thesis was to research how this information could be obtained. Literature review revealed that most of the quadcopters, whose source-code is available, use a complementary filter or some derivative of it to fuse data from a gyroscope, an accelerometer and often also a magnetometer. These sensors combined are called an Inertial Measurement Unit. This thesis focuses on calculating angles from each sensor’s data and fusing these with a complementary filter. On the basis of literature review and measurements using a quadcopter, the proposed filter provides sufficiently accurate attitude data for flight control system. However, a simple complementary filter has one significant drawback – it works reliably only when the quadcopter is hovering or moving at a constant speed. The reason is that an accelerometer can’t be used to measure angles accurately if linear acceleration is present. This problem can be fixed using some derivative of a complementary filter like an adaptive complementary filter or a Kalman filter, which are not covered in this thesis.

Supporting Parallel Legal Systems as a Means of Improving Access to Justice in Guatemala

Parallel legal systems can and do exist within a single sovereign nation, and rural Guatemala offers one example. Such parallel systems are generally viewed as failures of legal penetration which compromise the rule of law. The question addressed in this paper is whether the de facto existence of parallel systems in Guatemala benefits the indigenous population, or whether the ultimate goal of attaining access to justice requires a complete overhaul of the official legal system. Ultimately, the author concludes that while the official justice system needs a lot of work in order to expand access to justice, especially for the rural poor, the existence of a parallel legal system can be a vehicle for, rather than a hindrance to, expanding such access.

Innovation and Globalization Policy in Small Transition Countries ; Case study: Macedonia and Slovenia

Diese Arbeit befasst sich mit der Innovations- und Globalisierungspolitik in kleinen Transformationsländern am Beispiel Mazedoniens; diese wurde mit der Lage in Slowenien verglichen, einem Land von ungefähr gleicher Größe und mit gemeinsamer Vergangenheit als Teilrepublik der Jugoslawischen Föderation, aber mit einem wesentlich höheren ökonomischen Entwicklungsstand. Innovation wird dabei verstanden als „Herstellung, Anpassung und Ausnutzung von Neuerungen“, und sie wird durch das Umfeld, in dem sie stattfindet, beeinflusst. Anpassung und Ausnutzung sind gerade für kleine Transformationsländer von erheblicher Bedeutung, da ihre Fähigkeit zu Herstellung von Neuerungen sehr begrenzt sind. Die Rolle der Innovationspolitik besteht hierbei darin, institutionelle und organisationelle Regulierungen einzuführen, die ein günstiges Umfeld sowohl für Innovationen als auch für die Entwicklung eines nationalen Innovationssystems schaffen. Die Rolle der Politik besteht also nicht in der Innovation als solcher, sondern in der Herstellung der notwendigen Bedingungen für die Industrie und die Forschungseinrichtungen dahingehend zu schaffen, dass sie ihr Wissen, ihre Fertigkeiten und ihre praktischen Erfahrungen für innovative Tätigkeiten einsetzen können. Auf der einen Seite gibt es Institutionen und Organisationen, ohne die die Unternehmen rückständig und wenig leistungsstark wären (etwa das Patentamt oder Institutionen höherer Bildung), und auf der anderen Seite gibt es Institutionen und Organisationen, welche die Unternehmen dabei unterstützen, dass sie ihre Tätigkeit weiter unterstützen (z.B. durch Technologietransfer-Zentren und Netzwerke). Die Leistungen dieser Institutionen und Organisationen sind von großer Bedeutung für die nationalen Innovationssysteme und sollten ihrerseits durch Innovationspolitik unterstützt werden; dies bedeutet jedoch nicht, dass diese Leistungen vom Staat bereitgestellt werden, vielmehr sollte die Wirtschaftspolitik Möglichkeiten für die öffentlich/private oder sogar rein private Bereitstellung solcher Leistungen in Erwägung ziehen; dies würde nicht nur die Kosten für den Staat senken, sondern auch die Effizienz bei der Erstellung dieser Leistungen steigern. Die Arbeit kommt zu dem Schluss, dass das größte Problem der Innovationspolitik in Mazedonien darin besteht, dass es sie gar nicht gibt, und zwar nicht als Folge einer bewussten Entscheidung darüber. Tatsächlich müssen Ressourcen und Zeit für die Schaffung eines nationalen Innovationssystems eingesetzt werden mit Hilfe einer Politik, die sich auf die wesentlichen Umrisse konzentriert, wobei die Nachfrage nach Technologie im Unternehmensbereich gesteigert wird und das Wissen und das Informationsangebot restrukturiert wird. Dieses System muss offen sein, unter beständigem Verbesserungsdruck stehen und fähig sein, sich an Veränderungen anzupassen. Damit eine solche Politik erfolgreich ist, muss es einen Konsens darüber zwischen allen beteiligten Akteuren geben und darüber hinaus auch eine Kohärenz zwischen den verschiedenen politischen Institutionen. Das ist deswegen wichtig, weil der Innovationsprozess komplex ist und verschiedene Politikbereiche berührt. Ziel sollte die Schaffung eines Systems sein, das einerseits auf Autonomie und Kooperation aufbaut, andererseits aber auch Wettbewerb zwischen den beteiligten Institutionen und Organisationen fördert. Eine wichtige Bedingung für ein positives Investitionsklima im Bereich der Innovation ist die Erreichung von makroökonomischer Stabilität. Die gegenwärtige Situation ist gekennzeichnet durch Instabilität des Rechtswesens, durch Korruption und Probleme des Vertragsschutzes, die sowohl ausländische als auch inländische Akteure davon abhält, sich in wirtschaftlichen Aktivitäten in Mazedonien zu engagieren. Bei der Suche nach einem Ausweg aus diesen Problemen ist es wichtig für Mazedonien, von anderen Ländern wie Slowenien zu lernen, die ähnliche Probleme haben, aber auch schon Erfahrungen in der Problemlösung. Man muss dabei beachten, dass der Entwicklungsstand, das wirtschaftliche und das politische Umfeld in beiden Vergleichsländern sich erheblich unterscheiden, so dass die Lektionen, die Mazedonien von Slowenien lernen könnte, nicht direkt übertragen und kopiert werden können, sondern entsprechend angepasst werden müssen. Die vorliegende Arbeit liefert Einsichten in die Probleme der Innovationspolitik in Transformationsländern und liefert daher sowohl einen Anreiz als auch eine Quelle von Informationen für künftige Analysen der wirtschaftlichen Bedingungen und vor allem Innovationspolitik in Transformationsländern.

Slow and Smooth: A Bayesian Theory for the Combination of Local Motion Signals in Human Vision

In order to estimate the motion of an object, the visual system needs to combine multiple local measurements, each of which carries some degree of ambiguity. We present a model of motion perception whereby measurements from different image regions are combined according to a Bayesian estimator --- the estimated motion maximizes the posterior probability assuming a prior favoring slow and smooth velocities. In reviewing a large number of previously published phenomena we find that the Bayesian estimator predicts a wide range of psychophysical results. This suggests that the seemingly complex set of illusions arise from a single computational strategy that is optimal under reasonable assumptions.

El plan de lengua y cohesión social en Catañunya: primeros datos de una investigación = Language and Social Cohesion Plan in Catalonia: Initial research data

Los programas de inmersión lingüística han constituido y constituyen dentro del Sistema Educativo catalán la principal forma para que el alumnado de lengua familiar no-catalana aprenda una nueva lengua, el catalán, sin que, en su proceso de aprendizaje, vea mermado ni el desarrollo de su propia lengua ni su rendimiento académico. El éxito de la inmersión lingüística en las décadas anteriores ha sido frecuentemente utilizado como uno de los argumentos orientativos para justificar la política lingüística que se sigue en la escolarización de la infancia extranjera. Sin embargo, los resultados obtenidos por investigaciones recientes parece que no avalan empíricamente dicho argumento. Este artículo analiza dichos resultados y expone, a partir del Plan para la Lengua y Cohesión Social puesto en marcha por el Departamento de Educación de la Generalitat de Cataluña, cuáles son los retos que se presentan a su Sistema Educativo dentro del nuevo marco que supone el aumento de la diversidad cultural y lingüística en la actual sociedad catalana

Collaborative eLearning Assistant Network: caring agents are conscious agents

Would a research assistant - who can search for ideas related to those you are working on, network with others (but only share the things you have chosen to share), doesn’t need coffee and who might even, one day, appear to be conscious - help you get your work done? Would it help your students learn? There is a body of work showing that digital learning assistants can be a benefit to learners. It has been suggested that adaptive, caring, agents are more beneficial. Would a conscious agent be more caring, more adaptive, and better able to deal with changes in its learning partner’s life? Allow the system to try to dynamically model the user, so that it can make predictions about what is needed next, and how effective a particular intervention will be. Now, given that the system is essentially doing the same things as the user, why don’t we design the system so that it can try to model itself in the same way? This should mimic a primitive self-awareness. People develop their personalities, their identities, through interacting with others. It takes years for a human to develop a full sense of self. Nobody should expect a prototypical conscious computer system to be able to develop any faster than that. How can we provide a computer system with enough social contact to enable it to learn about itself and others? We can make it part of a network. Not just chatting with other computers about computer ‘stuff’, but involved in real human activity. Exposed to ‘raw meaning’ – the developing folksonomies coming out of the learning activities of humans, whether they are traditional students or lifelong learners (a term which should encompass everyone). Humans have complex psyches, comprised of multiple strands of identity which reflect as different roles in the communities of which they are part – so why not design our system the same way? With multiple internal modes of operation, each capable of being reflected onto the outside world in the form of roles – as a mentor, a research assistant, maybe even as a friend. But in order to be able to work with a human for long enough to be able to have a chance of developing the sort of rich behaviours we associate with people, the system needs to be able to function in a practical and helpful role. Unfortunately, it is unlikely to get a free ride from many people (other than its developer!) – so it needs to be able to perform a useful role, and do so securely, respecting the privacy of its partner. Can we create a system which learns to be more human whilst helping people learn?

Inovações tecnológicas na caprinocultura

O largo crescimento do setor de agronegócios no Brasil tem estimulado mudanças nos sistemas produtivos, tanto na intensificação, como na profissionalização da produção. Dessa forma, os produtores têm buscado estratégias para melhor atender aos desafios da atividade pecuária atual, dentre as quais se destacam as inovações tecnológicas que devem resultar em comprovado benefício à atividade, seja pelo aumento em produtividade, seja pela melhoria na qualidade dos produtos, seja pela conscientização do respeito ao meio ambiente. Assim como em outros segmentos do agronegócio brasileiro, na caprinocultura existe uma demanda crescente pela aplicação de inovações tecnológicas, uma vez que o sistema produtivo precisa ser mais competitivo para se manter no mercado. Dentre as inovações tecnológicas aplicadas na caprinocultura, foram abordadas as mais relevantes nas áreas de reprodução (desde métodos para indução de cio até a prática da transgenia), melhoramento genético (biogenética), sanidade (inovações no diagnóstico e prevenção de doenças de maior impacto na criação), nutrição (inovações nos sistemas de alimentação) e tratamento de dejetos (diminuição de contaminantes no ambiente). A utilização conjunta das inovações tecnológicas nos diferentes segmentos associados à cadeia produtiva caprina pode fazer com que ocorram melhorias nos rebanhos assim como nos produtos gerados.

Diuron exposure induces systemic and organ-specific toxicity following acute and sub-chronic exposure in male Wistar rats

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Custo de produção e indicadores de rentabilidade da cultura do milho safrinha

The objective of this study was to evaluate the production cost and profitability of the second season corn crop in the Medio Paranapanema region, São Paulo State Brazil, under two technological levels (middle and high technology), crop 2008/2009, and compare the results with the 2006/2007 agricultural year. Effective and total operational cost as well as five profitability indicators were used. It was concluded that the high technology production cost for corn crop (direct seedling, sowing during the recommended period, use of simple hybrid seed, application of side-dressing fertilization, and treatment of seeds with different insecticides) was superior to the middle technology production cost (direct seedling, sowing after the recommended time, use of double hybrid seed, and no side-dressing fertilization). However, the average cost was inferior (US$ 8.5), due to a higher yield (4 t). The high technology corn crop was profitable (gross income and profitability index of 14% and 12%, respectively). For the middle technology crop, profitability indexes pointed out that the cropping system needs to be reevaluated by technicians and research institutions, regarding the adequate technical recommendations. Profitability indexes decreased considerably in both cropping systems. It was verified that, in relation to the 2006/2007 harvest period, the total operational cost increased for both technologies, mainly because of the increase of supplies prices.

The modernization of bank supervision

Includes bibliography

Necessidades de formação continuada de professores do 1º ciclo do ensino fundamental

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Conhecimento básico de genética: concluintes do ensino e graduandos de ciências biológicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Melhoria da qualidade de um processo de usinagem utilizando as técnicas de avaliação de Taguchi

Delivering to the customers a product or service with the expected quality associated to the huge competitiveness that exists in the market nowadays, has been making organizations increasingly focus on quality planning using techniques which are directed towards the continuous improvement process and production optimization. Thus, this paper aims to improve a machining process using the techniques of experimental design to the optimization and this also includes the analysis of the measurement system. For this purpose, the alloy Nimonic 80A, a nickel base superalloy, was used in the process due to its widespread use for high temperatures, applying this study the robust method proposed by Genichi Taguchi, determining the influence of the factors considered input variables, cutting speed, feed rate, depth of cut, type of tool, lubrication, and material hardness, in the output or response variable, surface roughness, concluding with the use of Taguchi orthogonal array L16 and by analysis of ANOVA that the factor feed rate is significant and offers greater effect on the response variable studied, should be set to 0,12mm/rev. Moreover, the factor type of tool has more influence on the process when compared to other factors, being CP250 the one more suitable to the process. Lastly, the interaction feed rate x cutting speed provides greater significance in the process regarding to surface roughness variable, being the best match between them 0,12mm/rev to the feed rate and 90m/min to the cutting speed. In order to evaluate the measurement system, it was applied the repeatability and reproducibility method (R&R), through which we saw that the system needs improvement (R & R = 88.04% >>> 30%) as the value found in the study was well above compared to the one that classifies the system as inappropriate

Integrating on-line process control and imperfect corrective maintenance: An economical design

Existing studies of on-line process control are concerned with economic aspects, and the parameters of the processes are optimized with respect to the average cost per item produced. However, an equally important dimension is the adoption of an efficient maintenance policy. In most cases, only the frequency of the corrective adjustment is evaluated because it is assumed that the equipment becomes "as good as new" after corrective maintenance. For this condition to be met, a sophisticated and detailed corrective adjustment system needs to be employed. The aim of this paper is to propose an integrated economic model incorporating the following two dimensions: on-line process control and a corrective maintenance program. Both performances are objects of an average cost per item minimization. Adjustments are based on the location of the measurement of a quality characteristic of interest in a three decision zone. Numerical examples are illustrated in the proposal. (c) 2012 Elsevier B.V. All rights reserved.

Patterns in and kinetics of phase separation in binary mixtures

This work focused mainly on two aspects of kinetics of phase separation in binary mixtures. In the first part, we studied the interplay of hydrodynamics and the phase separation of binary mixtures. A considerably flat container (a laterally extended geometry), at an aspect ratio of 14:1 (diameter: height) was chosen, so that any hydrodynamic instabilities, if they arise, could be tracked. Two binary mixtures were studied. One was a mixture of methanol and hexane, doped with 5% ethanol, which phase separated under cooling. The second was a mixture of butoxyethanol and water, doped with 2% decane, which phase separated under heating. The dopants were added to bring down the phase transition temperature around room temperature.rnrnAlthough much work has been done already on classical hydrodynamic instabilities, not much has been done in the understanding of the coupling between phase separation and hydrodynamic instabilities. This work aimed at understanding the influence of phase separation in initiating any hydrodynamic instability, and also vice versa. Another aim was to understand the influence of the applied temperature protocol on the emergence of patterns characteristic to hydrodynamic instabilities. rnrnOn slowly cooling the system continuously, at specific cooling rates, patterns were observed in the first mixture, at the start of phase separation. They resembled the patterns observed in classical Rayleigh-Bénard instability, which arises when a liquid continuously is heated from below. To suppress this classical convection, the cooling setup was tuned such that the lower side of the sample always remained cooler by a few millikelvins, relative to the top. We found that the nature of patterns changed with different cooling rates, with stable patterns appearing for a specific cooling rate (1K/h). On the basis of the cooling protocol, we estimated a modified Rayleigh number for our system. We found that the estimated modified Rayleigh number is near the critical value for instability, for cooling rates between 0.5K/h and 1K/h. This is consistent with our experimental findings. rnrnThe origin of the patterns, in spite of the lower side being relatively colder with respect to the top, points to two possible reasons. 1) During phase separation droplets of either phases are formed, which releases a latent heat. Our microcalorimetry measurements show that the rise in temperature during the first phase separation is in the order of 10-20millikelvins, which in some cases is enough to reverse the applied temperature bias. Thus phase separation in itself initiates a hydrodynamic instability. 2) The second reason comes from the cooling protocol itself. The sample was cooled from above and below. At sufficiently high cooling rates, there are situations where the interior of the sample is relatively hotter than both top and bottom of the sample. This is sufficient to create an instability within the cell. Our experiments at higher cooling rates (5K/h and above) show complex patterns, which hints that there is enough convection even before phase separation occurs. Infact, theoretical work done by Dr.Hayase show that patterns could arise in a system without latent heat, with symmetrical cooling from top and bottom. The simulations also show that the patterns do not span the entire height of the sample cell. This is again consistent with the cell sizes measured in our experiment.rnrnThe second mixture also showed patterns at specific heating rates, when it was continuously heated inducing phase separation. In this case though, the sample was turbid for a long time until patterns appeared. A meniscus was most probably formed before the patterns emerged. We attribute the reason of patterns in this case to Marangoni convection, which is present in systems with an interface, where local differences in surface tension give rise to an instability. Our estimates for the Rayleigh number also show a significantly lower number than that's required for RB-type instability.rnrnIn the first part of the work, therefore, we identify two different kinds of hydrodynamic instabilities in two different mixtures. Both are observed during, or after the first phase separation. Our patterns compare with the classical convection patterns, but here the origins are from phase separation and the cooling protocol.rnrnIn the second part of the work, we focused on the kinetics of phase separation in a polymer solution (polystyrene and methylcyclohexane), which is cooled continuously far down into the two phase region. Oscillations in turbidity, denoting material exchange between the phases are seen. Three processes contribute to the phase separation: Nucleation of droplets, their growth and coalescence, and their subsequent sedimentation. Experiments in low molecular binary mixtures had led to models of oscillation [43] which considered sedimentation time scales much faster than the time scales of nucleation and growth. The size and shape of the sample therefore did not matter in such situations. The oscillations in turbidity were volume-dominated. The present work aimed at understanding the influence of sedimentation time scales for polymer mixtures. Three heights of the sample with same composition were studied side by side. We found that periods increased with the sample height, thus showing that sedimentation time determines the period of oscillations in the polymer solutions. We experimented with different cooling rates and different compositions of the mixture, and we found that periods are still determined by the sample height, and therefore by sedimentation time. rnrnWe also see that turbidity emerges in two ways; either from the interface, or throughout the sample. We suggest that oscillations starting from the interface are due to satellite droplets that are formed on droplet coalescence at the interface. These satellite droplets are then advected to the top of the sample, and they grow, coalesce and sediment. This type of an oscillation wouldn't require the system to pass the energy barrier required for homogenous nucleation throughout the sample. This mechanism would work best in sample where the droplets could be effectively advected throughout the sample. In our experiments, we see more interface dominated oscillations in the smaller cells and lower cooling rates, where droplet advection is favourable. In larger samples and higher cooling rates, we mostly see that the whole sample becomes turbid homogenously, which requires the system to pass the energy barrier for homogenous nucleation.rnrnOscillations, in principle, occur since the system needs to pass an energy barrier for nucleation. The height of the barrier decreases with increasing supersaturation, which in turn is from the temperature ramp applied. This gives rise to a period where the system is clear, in between the turbid periods. At certain specific cooling rates, the system can follow a path such that the start of a turbid period coincides with the vanishing of the last turbid period, thus eliminating the clear periods. This means suppressions of oscillations altogether. In fact we experimentally present a case where, at a certain cooling rate, oscillations indeed vanish. rnrnThus we find through this work that the kinetics of phase separation in polymer solution is different from that of a low molecular system; sedimentation time scales become relevant, and therefore so does the shape and size of the sample. The role of interface in initiating turbid periods also become much more prominent in this system compared to that in low molecular mixtures.rnrnIn summary, some fundamental properties in the kinetics of phase separation in binary mixtures were studied. While the first part of the work described the close interplay of the first phase separation with hydrodynamic instabilities, the second part investigated the nature and determining factors of oscillations, when the system was cooled deep into the two phase region. Both cases show how the geometry of the cell can affect the kinetics of phase separation. This study leads to further fundamental understandings of the factors contributing to the kinetics of phase separation, and to the understandings of what can be controlled and tuned in practical cases. rn