A switched-beam antenna of monopoles housed in a radial guide with transition to free space

The design of a switched-beam antenna formed by a circular array of monopoles housed inside a radial guide with a transition to free space is presented. Two alternative types of transitions to free space, one using a truncated conducting cone and the other created by a tapered dielectric material at the edge of the radial guide, are described. The use of the radial guide with transition increases the return-loss bandwidth of the array and enables shaping its beam in elevation. (C) 2004 Wiley Periodicals, Inc.

Axially Symmetric Radiation Patterns from Corrugated

A modified H-plane sectoral horn antenna with identical E- and'H- plane.patterns over the X-band frequency is discussed. This system has significantly reduced side lobes and hack lobes. Half=power beam width and gain of the antenna are also improved with enhanced matching , Experimental results for a number of horns with various flanges are presented . These find practical application for illuminating symmetric antennas like paraboloids and polarization measurements in radio astronomy, etc. Compared to the fixed pyramidal horns. the present system offers great convenience in trimming the antenna characteristics

Micromachined waveguide antennas for 1.6 THz

A new type of horn antenna for operation at 1.6 THz, that can be fabricated monolithically with 1/4-height micromachined waveguide, is described. Height, limitations imposed by the micromachining process are overcome by removing a tapered slot in the upper surface of a scalar horn, allowing the E-plane fields to extend outside the confines of the metallic structure before radiation, with a consequent reduction in E-plane beamwidth. 1.6 THz radiation pattern measurements for different designs show that, while there is scope for further optimisation, 3 dB beamwidths of 24 degrees and 17.5 degrees in the E- and H-planes, respectively, can be achieved.

Fabrication and characterization of micromachined rectangular waveguide components for use at millimeter-wave and terahertz frequencies

The fabrication and characterization of micromachined reduced-height air-filled rectangular waveguide components suitable for integration is reported in this paper. The lithographic technique used permits structures with heights of up to 100 μm to be successfully constructed in a repeatable manner. Waveguide S-parameter measurements at frequencies between 75-110 GHz using a vector network analyzer demonstrate low loss propagation in the TE10 mode reaching 0.2 dB per wavelength. Scanning electron microscope photographs of conventional and micromachined waveguides show that the fabrication technique can provide a superior surface finish than possible with commercially available components. In order to circumvent problems in efficiently coupling free-space propagating beams to the reduced-height G-band waveguides, as well as to characterize them using quasi-optical techniques, a novel integrated micromachined slotted horn antenna has been designed and fabricated, E-, H-, and D-plane far-field antenna pattern measurements at different frequencies using a quasi-optical setup show that the fabricated structures are optimized for 180-GHz operation with an E-plane half-power beamwidth of 32° elevated 35° above the substrate, a symmetrical H-plane pattern with a half-power beamwidth of 23° and a maximum D-plane cross-polar level of -33 dB. Far-field pattern simulations using HFSS show good agreement with experimental results.

MIAWARA-C, a new ground based water vapor radiometer for measurement campaigns

In this paper a new 22 GHz water vapor spectro-radiometer which has been specifically designed for profile measurement campaigns of the middle atmosphere is presented. The instrument is of a compact design and has a simple set up procedure. It can be operated as a standalone instrument as it maintains its own weather station and a calibration scheme that does not rely on other instruments or the use of liquid nitrogen. The optical system of MIAWARA-C combines a choked gaussian horn antenna with a parabolic mirror which reduces the size of the instrument in comparison with currently existing radiometers. For the data acquisition a correlation receiver is used together with a digital cross correlating spectrometer. The complete backend section, including the computer, is located in the same housing as the instrument. The receiver section is temperature stabilized to minimize gain fluctuations. Calibration of the instrument is achieved through a balancing scheme with the sky used as the cold load and the tropospheric properties are determined by performing regular tipping curves. Since MIAWARA-C is used in measurement campaigns it is important to be able to determine the elevation pointing in a simple manner as this is a crucial parameter in the calibration process. Here we present two different methods; scanning the sky and the Sun. Finally, we report on the first spectra and retrieved water vapor profiles acquired during the Lapbiat campaign at the Finnish Meteorological Institute Arctic Research Centre in Sodankylä, Finland. The performance of MIAWARA-C is validated here by comparison of the presented profiles against the equivalent profiles from the Microwave Limb Sounder on the EOS/Aura satellite.

Diseño, implementación y verificación de una antena de microondas

A lo largo de este proyecto se han tratado las diferentes fases que tienen lugar durante el desarrollo del programa de Diseño y Verificación de una Bocina en Banda C destinada a un satélite comercial de comunicaciones. En un primer lugar, se introduce el proyecto en el mundo real realizando una pequeña aproximación a los satélites artificiales y su historia. Después, en una primera fase, se describen los diversos puntos de la etapa de diseño y los resultados de la simulación de nuestra Antena. Se estudian por separado los diferentes elementos que componen el equipo, y además, se realiza un análisis de los parámetros eléctricos que se deben tener en cuenta durante el diseño para adaptar el comportamiento de la Antena a los requisitos solicitados por el cliente. Antes de realizar la verificación de la Antena, se procede a la definición de los ensayos, que se debe realizar sobre el equipo con el fin de simular las condiciones a las que se verá sometido. Pruebas y medidas, niveles de test, etc. que nos ayudan a demostrar que nuestra Antena está preparada para realizar su misión en el espacio. Se hará una descripción sobre la forma de realizar de los ensayos y de las instalaciones donde se van a llevar a cabo, además del orden que llevaremos durante la campaña. Una vez determinados los test y con la Antena fabricada y lista, se procede a la Verificación de nuestro equipo mediante la Campaña de Ensayos con el objetivo de caracterizar por completo el funcionamiento de nuestra Antena en cualquier circunstancia. Se muestran los resultados obtenidos en los test siguiendo el orden establecido por el Test Plan. Medidas en Laboratorio y Radiación, los test de vibración y las pruebas ambientales en las Cámaras Térmicas de Vacío, y medidas eléctricas en condiciones extremas de temperatura y presión. Y una vez realizada la Campaña, se vuelve a medir la Antena para comprobar el funcionamiento tras soportar todos los ensayos. Se analizan los resultados obtenidos en cada una de las pruebas y se comparan con las simulaciones obtenidas durante la fase de diseño. Finalmente, se realiza un pequeño resumen de los valores más importantes obtenidos durante la Verificación y exponen las Conclusiones que se desprende de dicho proceso. Como último punto del proyecto, se estudian las correcciones y mejoras que se podrán llevar a cabo en futuros programas gracias a lo que hemos aprendido en este proyecto. Abstract This project presents a C Band Horn Antenna for a commercial communications satellite. All the different phases from Design to Verification are presented. First of all, an introduction to artificial satellites and their history is presented to put this project into perspective. Next, the electrical design of the Antenna is presented. Taking into account the theoretical fundamentals, each element that comprises this Antenna was designed. Their electrical performances, obtained from analysis using commercial software, are presented in the simulation results. In the design of each element of the antenna, some critical parameters are set and optimized in order to be compliant with the global requirements requested by the customer. After the design is completed, it is necessary to define the Test Campaign that has to be carried out in order to verify the validity of the designed and manufactured Antenna. Therefore, a Test Plan and the Electrical and Environmental Test Procedures are defined. This Test Campaign must be representative of the same conditions of the real space mission. Considering this, the following are defined: parameters for the network analyzer and radiation patterns measurements; test levels for the environmental test; definition of the RF measurements to be carried out and the temperatures to be applied in the thermal vacuum cycling. If the Antenna surpasses these tests, it will be ready to perform its mission in space over the entire satellite’s life cycle. The facilities where the tests are performed, as well as the sequence of the tests along the campaign are described too. After that, the Test Campaign is performed to fully characterize the Antenna in the space simulated conditions. Following the order established in the Test Plan, a radiation pattern and laboratory parameters are measured to correlate its electrical response with the simulations. Then, vibration and thermal vacuum tests are performed to verify its behavior in extreme environmental conditions. Last, if the final electrical results are the same as the initial ones, it can be stated that the antenna has successfully passed the Test Campaign. And finally, conclusions obtained from the data simulation design and Test Campaign results are presented. Status of Compliance with the specification is shown to demonstrate that the Antenna fulfills the requested requirements. Although the purpose of this project is to design and verify the response of C Band Horn Antenna, it is important to highlight improvements for future developments and the lessons learnt during this project.

Análisis paramétrico de transiciones a bocinas

Las transiciones en guía de onda son las estructuras utilizadas en microondas para transferir y adaptar la señal que viaja en un determinado sistema de transmisión (por ejemplo, un cable coaxial) a otro sistema de transmisión o a un sistema radiante (por ejemplo, una antena de bocina). Los dos sistemas de transmisión entre los que la transición adapta la señal pueden ser distintos o del mismo tipo pero con alguna de sus dimensiones diferente. Existen diferentes transiciones de guía de onda que dependiendo de su utilidad son diseñadas y construidas con diferentes secciones: circular, rectangular, elíptica o incluso combinaciones de éstas. No es necesario que la sección de la guía presente una forma geométrica conocida pero los estándares que se van a seguir hacen referencia en concreto a secciones rectangulares y circulares. En el trabajo que aquí se desarrolla se pretende optimizar por medio de simulaciones paramétricas una transición entre cable coaxial con conector tipo K y una guía de onda de sección circular que sigue el estándar presentado por Flann, Millitech y Antarfs para la banda WR34. La transición que va a ser objeto de este estudio se denomina transición tapered o transición conformada. Este tipo de transiciones se caracterizan por variar una de sus dimensiones progresivamente hasta llegar al tamaño definido en el estándar correspondiente. La manera de realizar la optimización de la transición se basará en el estudio del parámetro S11 que presente la estructura a lo largo de la banda de trabajo. Ya que se sigue el estándar WR34 la banda de trabajo que éste comprende va de 21,7 a 33 GHz. Se pretende conseguir que la respuesta del parámetro S11 se encuentre por debajo de -20 dB en la banda de WR34 como resultado del diseño para poder contar de esta manera con una buena adaptación. Finalmente se propondrá un criterio a seguir para optimizar este tipo de transiciones siguiendo el objetivo de mejor adaptación teniendo en cuenta el impacto de cada tramo sobre el rango de frecuencias en el que influye y se presentarán las características finales que presenta la transición bajo estudio. En este documento se introduce de manera breve la utilidad de los transformadores de impedancias lambda cuartos en líneas de transmisión, el estado del arte de las diferentes técnicas para su diseño, y la propuesta de diseño y caracterización objeto del presente trabajo. Posteriormente, se presenta el caso de estudio para el diseño de la transición para ser integrada a una bocina de choke. Luego, se introduce el marco teórico del trabajo presentando algunos ejemplos ilustrativos de tramos de guía de onda rectangular y guía de onda circular, introduciendo adaptadores de λ/4 en simulaciones. A continuación, se explica la implementación del modelo bajo estudio en CST (Computer Simulation Technology) Studio Suite. Finalmente se presenta la discusión de los resultados obtenidos, las conclusiones y líneas futuras de trabajo. ABSTRACT. Waveguide transitions are structures used in microwave in order to transfer and adapt the signal that travels from a certain transmission system (e.g. coaxial cable) to other transmission system or to a radiant system (e.g. horn antenna). Both transmission systems between which the transition adapts the signal can be different or from the same type, but with differences in some of their dimensions. There are different waveguide transitions that, depending on their utility, are designed and constructed in different sections: circular, rectangular, elliptic or combinations of the former. The section of the guide does not have to have a known geometric shape, although the standards to be followed in this thesis apply to rectangular and circular sections. In the work here presented, we aim to optimize by means of parametric simulations, a transition between a coaxial cable with a K-type connector and a waveguide with circular section following the standard presented by Flann, Millitech y Antarfs for the band WR34. The transition studied is called tapered transition, which is characterized by the progressive variation of its dimensions, until reaching the defined size of the corresponding standard. The way of optimizing the transition will be based in the study of the parameter S11 presented by the structure along the bandwidth. Since the standard used is the WR34, the bandwidth can be defined from 21.7 up to 33 GHz. It is aimed that the response of the S11 parameter be lower equal than -20dB in the frequency band under study according to the design in order to be well matched. Finally, a criterion to follow is proposed in order to optimize these transitions type, following the better-match objective. That will be done taking into account the impact of each section on the frequency range in which influences and the final characteristics of the studied transition will be presented. In this document, it is briefly introduced the utility of quarter-wave impedance transformers in transmission lines, the state-of-art of the different techniques for their design, and the proposal of design and characterization aimed with this work. Afterwards, the study case for the design of the transition to be integrated with a choke horn antenna will be presented. Later, the theoretical frame work is introduced, giving some illustrative examples of rectangular and circular waveguide sections, and also introducing λ/4 adaptors in the simulations. Subsequently, the implementation of the model under study in CST (Computer Simulation Technology) Studio Suite will be explained. Finally, the discussion of the results, conclusion and future lines of the work are presented.

Wideband Oylindrioal Dielectric Resonator Antenna Excited Using an L-strip Feed

A broadband cylindrical dielectric resonator antenna (DRA) energized with an L-strip feed is presented The novel exciting technique achieves a 2:1 VSWR bandwidth of 18%. The variation of bandwidth for different feed parameters is also studied

Single-feed dual-frequency dual-polarized slotted square microstrip antenna

A novel dual frequency dual-polarized square microstrip patch antenna embedded with a slot is presented. The proposed antenna offers tunability of the frequency ratio between the two frequencies by adjusting the slot dimensions. This configuration also provides a size reduction up to -51 and 35% for the two modes as compared to a square micro strip patch antenna

FDTD analysis of a symmetric T-strip fed wideband rectangular microstrip antenna

A theoretical analysis of a symmetric T-shaped rnicrostripfed rectangular microstrip antenna using the finite-difference titnedoniain (FDTD) method is presented in this paper. The resonant frequency, return loss, impedance bandwidth, and radiation patterns are predicted and are in good agreement with the measured results

L-strip excited wideband rectangular microstrip antenna

This paper presents the outcome of the experimental studies performed on L-strip fed compact rectangular microstrip antenna. The effect of the feed parameters upon the characteristics of the antenna is studied in detail. The antenna offers an impedance bandwidth of nearly 20% and is suitable for broadband applications

T-strip-fed High-Permittivity Rectangular Dielectric Resonator Antenna for Broadband Applications

rectangular low-density, high-permittivity dielectric resona or antenna (DRA) excited by T-shaped microstrip feed offering a 2:1 VSWR bandwidth of -22% at 2.975 GHz is reported. The design methoaology and experimental results of the antenna are discussed. The excellent gain and radiation performance of the proposed antenna project: it as a potential candidate for telecommunication applications

L-strip-fed Wideband Rectangular Dielectric Resonator Antenna

In this paper, the advantages of using L-shaped microviij) feed to e.tcite a rectangular dielectric resonator cuuenna (DRA) by elemanagnetic coupling are presented. This feeding technique enhances the hardsvidth and gain of the antenna without affecting its size. The experimental re srdts are validated using Fidelity software based on the finitedifference tine-domain (FDTD) method

Investigations on the radiation characteristics of new hollow dielectric horn antennas

Investigations on the design and development of certain new hollow dielectric hom antennas of rectangular cross section have been carried out. The main shortcoming of the existing ordinary hollow dielectric hom antenna (HDH) is the abrupt discontinuity at the feed-end. A new launching technique using a dielectric rod is introduced to overcome this limitation. Also a strip loading technique is employed for further modification of the antenna. Radiation parameters of new I-IDH antennas of Eplane sectoral, H-plane sectoral and pyramidal types were studied and are found to be very attractive. Theoretical approach based on Marcatili’s principle and two aperture theory along with diffraction theory and image theory is used to support the experimental findings. The HDH is considered as solid horn of effective dielectric constant and the aperture field is evaluated. The antenna is excited by the open waveguide in the dominant TE1o mode and so the existence of any hybrid mode is mled-out. The theoretical results are observed to be in good agreement with the experimental results.