Evaluation of integrated inverter topologies for low power PV systems

This work presents the stage integration in power electronics converters as a suitable solution for solar photovoltaic inverters. The rated voltages available in Photovoltaic (PV) modules have usually low values for applications such as regulated output voltages in stand-alone or grid-connected configurations. In these cases, a boost stage or a transformer will be necessary. Transformers have low efficiencies, heavy weights and have been used only when galvanic isolation is mandatory. Furthermore, high-frequency transformers increase the converter complexity. Therefore, the most usual topologies use a boost stage and one inverter stage cascaded. However, the complexity, size, weight, cost and lifetime might be improved considering the integration of both stages. These are the expected features to turn attractive this kind of integrated structures. Therefore, some integrated converters are analyzed and compared in this paper in order to support future evaluations and trends for low power single-phase inverters for PV systems. © 2011 IEEE.

A comparative study of MPPT strategies and a novel singlephase integrated buck-boost inverter for small wind energy conversion systems

This paper presents the analysis of some usual MPPT (Maximum Power Point Tracking) strategies intended for small wind energy conversion (up to 1kW) based on permanent magnet synchronous generators (PMSG), considering the stand-alone application for a novel buck-boost integrated inverter. Each MPPT method is analytically introduced and then it is simulated using MatLab/Simulink considering standard conditions of wind and also commercially available turbines and generators. The extracted power in each case is compared with the maximum available power, so the tracking factor is calculated for each method. Thus, the focus is on the application to improve the efficiency of stand-alone wind energy conversion systems (WECS) with battery chargers and AC load supplied by inverter. Therefore, for this purpose a novel single phase buck-boost integrated inverter is introduced. Finally, the main experimental results for the introduced inverter are presented. © 2011 IEEE.

Three-phase tri-state integrated boost inverter with special space vector and dq0 control

This paper presents a three-phase integrated inverter suitable for stand-alone and grid-connected applications. Furthermore, the utilization of the special features of the tri-state coupled with the new space vector modulation allows the converter to present an attractive degree of freedom for the designing of the controllers. Additionally, the control is derived through dq0 transformation, all the system is described and interesting simulation results are available to confirm the proposal. © 2012 IEEE.

Inversores integrados monofásicos e trifásicos para aplicações fotovoltaicas: técnicas para obtenção de mppt, detecção e proteção de ilhamento, sincronização e paralelismo com a rede de distribuição de energia elétrica

Pós-graduação em Engenharia Elétrica - FEIS

Paralelismo de inversores monofásicos, isolados ou em conexão com a rede, com otimização da resposta dinâmica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Negotiating social and moral order in internet relay chat

Although internet chat is a significant aspect of many internet users’ lives, the manner in which participants in quasi-synchronous chat situations orient to issues of social and moral order remains to be studied in depth. The research presented here is therefore at the forefront of a continually developing area of study. This work contributes new insights into how members construct and make accountable the social and moral orders of an adult-oriented Internet Relay Chat (IRC) channel by addressing three questions: (1) What conversational resources do participants use in addressing matters of social and moral order? (2) How are these conversational resources deployed within IRC interaction? and (3) What interactional work is locally accomplished through use of these resources? A survey of the literature reveals considerable research in the field of computer-mediated communication, exploring both asynchronous and quasi-synchronous discussion forums. The research discussed represents a range of communication interests including group and collaborative interaction, the linguistic construction of social identity, and the linguistic features of online interaction. It is suggested that the present research differs from previous studies in three ways: (1) it focuses on the interaction itself, rather than the ways in which the medium affects the interaction; (2) it offers turn-by-turn analysis of interaction in situ; and (3) it discusses membership categories only insofar as they are shown to be relevant by participants through their talk. Through consideration of the literature, the present study is firmly situated within the broader computer-mediated communication field. Ethnomethodology, conversation analysis and membership categorization analysis were adopted as appropriate methodological approaches to explore the research focus on interaction in situ, and in particular to investigate the ways in which participants negotiate and co-construct social and moral orders in the course of their interaction. IRC logs collected from one chat room were analysed using a two-pass method, based on a modification of the approaches proposed by Pomerantz and Fehr (1997) and ten Have (1999). From this detailed examination of the data corpus three interaction topics are identified by means of which participants clearly orient to issues of social and moral order: challenges to rule violations, ‘trolling’ for cybersex, and experiences regarding the 9/11 attacks. Instances of these interactional topics are subjected to fine-grained analysis, to demonstrate the ways in which participants draw upon various interactional resources in their negotiation and construction of channel social and moral orders. While these analytical topics stand alone in individual focus, together they illustrate different instances in which participants’ talk serves to negotiate social and moral orders or collaboratively construct new orders. Building on the work of Vallis (2001), Chapter 5 illustrates three ways that rule violation is initiated as a channel discussion topic: (1) through a visible violation in open channel, (2) through an official warning or sanction by a channel operator regarding the violation, and (3) through a complaint or announcement of a rule violation by a non-channel operator participant. Once the topic has been initiated, it is shown to become available as a topic for others, including the perceived violator. The fine-grained analysis of challenges to rule violations ultimately demonstrates that channel participants orient to the rules as a resource in developing categorizations of both the rule violation and violator. These categorizations are contextual in that they are locally based and understood within specific contexts and practices. Thus, it is shown that compliance with rules and an orientation to rule violations as inappropriate within the social and moral orders of the channel serves two purposes: (1) to orient the speaker as a group member, and (2) to reinforce the social and moral orders of the group. Chapter 6 explores a particular type of rule violation, solicitations for ‘cybersex’ known in IRC parlance as ‘trolling’. In responding to trolling violations participants are demonstrated to use affiliative and aggressive humour, in particular irony, sarcasm and insults. These conversational resources perform solidarity building within the group, positioning non-Troll respondents as compliant group members. This solidarity work is shown to have three outcomes: (1) consensus building, (2) collaborative construction of group membership, and (3) the continued construction and negotiation of existing social and moral orders. Chapter 7, the final data analysis chapter, offers insight into how participants, in discussing the events of 9/11 on the actual day, collaboratively constructed new social and moral orders, while orienting to issues of appropriate and reasonable emotional responses. This analysis demonstrates how participants go about ‘doing being ordinary’ (Sacks, 1992b) in formulating their ‘first thoughts’ (Jefferson, 2004). Through sharing their initial impressions of the event, participants perform support work within the interaction, in essence working to normalize both the event and their initial misinterpretation of it. Normalising as a support work mechanism is also shown in relation to participants constructing the ‘quiet’ following the event as unusual. Normalising is accomplished by reference to the indexical ‘it’ and location formulations, which participants use both to negotiate who can claim to experience the ‘unnatural quiet’ and to identify the extent of the quiet. Through their talk participants upgrade the quiet from something legitimately experienced by one person in a particular place to something that could be experienced ‘anywhere’, moving the phenomenon from local to global provenance. With its methodological design and detailed analysis and findings, this research contributes to existing knowledge in four ways. First, it shows how rules are used by participants as a resource in negotiating and constructing social and moral orders. Second, it demonstrates that irony, sarcasm and insults are three devices of humour which can be used to perform solidarity work and reinforce existing social and moral orders. Third, it demonstrates how new social and moral orders are collaboratively constructed in relation to extraordinary events, which serve to frame the event and evoke reasonable responses for participants. And last, the detailed analysis and findings further support the use of conversation analysis and membership categorization as valuable methods for approaching quasi-synchronous computer-mediated communication.

Electronic tendering: an industry perspective

The construction industry is categorised as being an information-intensive industry and described as one of the most important industries in any developed country, facing a period of rapid and unparalleled change (Industry Science Resources 1999) (Love P.E.D., Tucker S.N. et al. 1996). Project communications are becoming increasingly complex, with a growing need and fundamental drive to collaborate electronically at project level and beyond (Olesen K. and Myers M.D. 1999; Thorpe T. and Mead S. 2001; CITE 2003). Yet, the industry is also identified as having a considerable lack of knowledge and awareness about innovative information and communication technology (ICT) and web-based communication processes, systems and solutions which may prove beneficial in the procurement, delivery and life cycle of projects (NSW Government 1998; Kajewski S. and Weippert A. 2000). The Internet has debatably revolutionised the way in which information is stored, exchanged and viewed, opening new avenues for business, which only a decade ago were deemed almost inconceivable (DCITA 1998; IIB 2002). In an attempt to put these ‘new avenues of business’ into perspective, this report provides an overall ‘snapshot’ of current public and private construction industry sector opportunities and practices in the implementation and application of web-based ICT tools, systems and processes (e-Uptake). Research found that even with a reserved uptake, the construction industry and its participating organisations are making concerted efforts (fortunately with positive results) in taking up innovative forms of doing business via the internet, including e-Tendering (making it possible to manage the entire tender letting process electronically and online) (Anumba C.J. and Ruikar K. 2002; ITCBP 2003). Furthermore, Government (often a key client within the construction industry),and with its increased tendency to transact its business electronically, undoubtedly has an effect on how various private industry consultants, contractors, suppliers, etc. do business (Murray M. 2003) – by offering a wide range of (current and anticipated) e-facilities / services, including e-Tendering (Ecommerce 2002). Overall, doing business electronically is found to have a profound impact on the way today’s construction businesses operate - streamlining existing processes, with the growth in innovative tools, such as e-Tender, offering the construction industry new responsibilities and opportunities for all parties involved (ITCBP 2003). It is therefore important that these opportunities should be accessible to as many construction industry businesses as possible (The Construction Confederation 2001). Historically, there is a considerable exchange of information between various parties during a tendering process, where accuracy and efficiency of documentation is critical. Traditionally this process is either paper-based (involving large volumes of supporting tender documentation), or via a number of stand-alone, non-compatible computer systems, usually costly to both the client and contractor. As such, having a standard electronic exchange format that allows all parties involved in an electronic tender process to access one system only via the Internet, saves both time and money, eliminates transcription errors and increases speed of bid analysis (The Construction Confederation 2001). Supporting this research project’s aims and objectives, researchers set to determine today’s construction industry ‘current state-of-play’ in relation to e-Tendering opportunities. The report also provides brief introductions to several Australian and International e-Tender systems identified during this investigation. e-Tendering, in its simplest form, is described as the electronic publishing, communicating, accessing, receiving and submitting of all tender related information and documentation via the internet, thereby replacing the traditional paper-based tender processes, and achieving a more efficient and effective business process for all parties involved (NT Governement 2000; NT Government 2000; NSW Department of Commerce 2003; NSW Government 2003). Although most of the e-Tender websites investigated at the time, maintain their tendering processes and capabilities are ‘electronic’, research shows these ‘eTendering’ systems vary from being reasonably advanced to more ‘basic’ electronic tender notification and archiving services for various industry sectors. Research also indicates an e-Tender system should have a number of basic features and capabilities, including: • All tender documentation to be distributed via a secure web-based tender system – thereby avoiding the need for collating paperwork and couriers. • The client/purchaser should be able to upload a notice and/or invitation to tender onto the system. • Notification is sent out electronically (usually via email) for suppliers to download the information and return their responses electronically (online). • During the tender period, updates and queries are exchanged through the same e-Tender system. • The client/purchaser should only be able to access the tenders after the deadline has passed. • All tender related information is held in a central database, which should be easily searchable and fully audited, with all activities recorded. • It is essential that tender documents are not read or submitted by unauthorised parties. • Users of the e-Tender system are to be properly identified and registered via controlled access. In simple terms, security has to be as good as if not better than a manual tender process. Data is to be encrypted and users authenticated by means such as digital signatures, electronic certificates or smartcards. • All parties must be assured that no 'undetected' alterations can be made to any tender. • The tenderer should be able to amend the bid right up to the deadline – whilst the client/purchaser cannot obtain access until the submission deadline has passed. • The e-Tender system may also include features such as a database of service providers with spreadsheet-based pricing schedules, which can make it easier for a potential tenderer to electronically prepare and analyse a tender. Research indicates the efficiency of an e-Tender process is well supported internationally, with a significant number, yet similar, e-Tender benefits identified during this investigation. Both construction industry and Government participants generally agree that the implementation of an automated e-Tendering process or system enhances the overall quality, timeliness and cost-effectiveness of a tender process, and provides a more streamlined method of receiving, managing, and submitting tender documents than the traditional paper-based process. On the other hand, whilst there are undoubtedly many more barriers challenging the successful implementation and adoption of an e-Tendering system or process, researchers have also identified a range of challenges and perceptions that seem to hinder the uptake of this innovative approach to tendering electronically. A central concern seems to be that of security - when industry organisations have to use the Internet for electronic information transfer. As a result, when it comes to e-Tendering, industry participants insist these innovative tendering systems are developed to ensure the utmost security and integrity. Finally, if Australian organisations continue to explore the competitive ‘dynamics’ of the construction industry, without realising the current and future, trends and benefits of adopting innovative processes, such as e-Tendering, it will limit their globalising opportunities to expand into overseas markets and allow the continuation of international firms successfully entering local markets. As such, researchers believe increased knowledge, awareness and successful implementation of innovative systems and processes raises great expectations regarding their contribution towards ‘stimulating’ the globalisation of electronic procurement activities, and improving overall business and project performances throughout the construction industry sectors and overall marketplace (NSW Government 2002; Harty C. 2003; Murray M. 2003; Pietroforte R. 2003). Achieving the successful integration of an innovative e-Tender solution with an existing / traditional process can be a complex, and if not done correctly, could lead to failure (Bourn J. 2002).

Web-based public participatory GIS

Decision support systems (DSS) have evolved rapidly during the last decade from stand alone or limited networked solutions to online participatory solutions. One of the major enablers of this change is the fastest growing areas of geographical information system (GIS) technology development that relates to the use of the Internet as a means to access, display, and analyze geospatial data remotely. World-wide many federal, state, and particularly local governments are designing to facilitate data sharing using interactive Internet map servers. This new generation DSS or planning support systems (PSS), interactive Internet map server, is the solution for delivering dynamic maps and GIS data and services via the world-wide Web, and providing public participatory GIS (PPGIS) opportunities to a wider community (Carver, 2001; Jankowski & Nyerges, 2001). It provides a highly scalable framework for GIS Web publishing, Web-based public participatory GIS (WPPGIS), which meets the needs of corporate intranets and demands of worldwide Internet access (Craig, 2002). The establishment of WPPGIS provides spatial data access through a support centre or a GIS portal to facilitate efficient access to and sharing of related geospatial data (Yigitcanlar, Baum, & Stimson, 2003). As more and more public and private entities adopt WPPGIS technology, the importance and complexity of facilitating geospatial data sharing is growing rapidly (Carver, 2003). Therefore, this article focuses on the online public participation dimension of the GIS technology. The article provides an overview of recent literature on GIS and WPPGIS, and includes a discussion on the potential use of these technologies in providing a democratic platform for the public in decision-making.

Mailed treatment to augment primary care for alcohol disorders : a randomised controlled trial

Introduction and Aims: Remote delivery of interventions is needed to address large numbers of people with alcohol use disorders who are spread over large areas. Previous correspondence trials typically examined its effects as stand-alone treatment. This study aimed to test whether adding postal treatment to general practitioner (GP) support would lower alcohol use more than GP intervention alone. Design and Methods: A single-blind, randomised controlled trial with a crossover design was conducted over 12 months on 204 people with alcohol use disorders. Participants in an immediate correspondence condition received treatment over the first 3 months; those receiving delayed treatment received it in months 3–6. Results: Few participants were referred from GPs, and little intervention was offered by them. At 3 months, 78% of participants remained in the study. Those in immediate treatment showed greater reductions in alcohol per week, drinking days, anxiety, depression and distress than those in the delayed condition. However, post-treatment and follow-up outcomes still showed elevated alcohol use, depression, anxiety and distress. Greater baseline anxiety predicted better alcohol outcomes, although more mental distress at baseline predicted dropout. Discussion and Conclusions: The study gave consistent results with those from previous research on correspondence treatments, and showed that high levels of participant engagement over 3 months can be obtained. Substantial reductions in alcohol use are seen, with indications that they are well maintained. However, many participants continue to show high-risk alcohol use and psychological distress.

Designing for engagement : building IT systems

Context The School of Information Technology at QUT has recently undertaken a major restructuring of their Bachelor of Information Technology (BIT) course. Some of the aims of this restructuring include a reduction in first year attrition and to provide an attractive degree course that meets both student and industry expectations. Emphasis has been placed on the first semester in the context of retaining students by introducing a set of four units that complement one another and provide introductory material on technology, programming and related skills, and generic skills that will aid the students throughout their undergraduate course and in their careers. This discussion relates to one of these four fist semester units, namely Building IT Systems. The aim of this unit is to create small Information Technology (IT) systems that use programming or scripting, databases as either standalone applications or web applications. In the prior history of teaching introductory computer programming at QUT, programming has been taught as a stand alone subject and integration of computer applications with other systems such as databases and networks was not undertaken until students had been given a thorough grounding in those topics as well. Feedback has indicated that students do not believe that working with a database requires programming skills. In fact, the teaching of the building blocks of computer applications have been compartmentalized and taught in isolation from each other. The teaching of introductory computer programming has been an industry requirement of IT degree courses as many jobs require at least some knowledge of the topic. Yet, computer programming is not a skill that all students have equal capabilities of learning (Bruce et al., 2004) and this is clearly shown by the volume of publications dedicated to this topic in the literature over a broad period of time (Eckerdal & Berglund, 2005; Mayer, 1981; Winslow, 1996). The teaching of this introductory material has been done pretty much the same way over the past thirty years. During this period of time that introductory computer programming courses have been taught at QUT, a number of different programming languages and programming paradigms have been used and different approaches to teaching and learning have been attempted in an effort to find the golden thread that would allow students to learn this complex topic. Unfortunately, computer programming is not a skill that can be learnt in one semester. Some basics can be learnt but it can take many years to master (Norvig, 2001). Faculty data typically has shown a bimodal distribution of results for students undertaking introductory programming courses with a high proportion of students receiving a high mark and a high proportion of students receiving a low or failing mark. This indicates that there are students who understand and excel with the introductory material while there is another group who struggle to understand the concepts and practices required to be able to translate a specification or problem statement into a computer program that achieves what is being requested. The consequence of a large group of students failing the introductory programming course has been a high level of attrition amongst first year students. This attrition level does not provide good continuity in student numbers in later years of the degree program and the current approach is not seen as sustainable.

Australia : LIS education

The topic of library and information science (LIS) education has been under the spotlight in the professional literature in Australia and New Zealand for a number of years. Critical issues of discussion encompass the apparent lack of a core curriculum for the discipline, the perceived gulf between LIS education and LIS practice, and the pressing need for career-long learning and development. One of the central points of debate that emerges repeatedly is the long-standing question about the positioning of the profession: Is LIS a graduate profession of highly skilled individuals valued for their expertise and professionalism or is it a profession of anyone who works in a library, regardless of their qualifications (LIANZA, 2005)? While Australia and New Zealand do not stand alone in this debate – similar issues are echoed in many other countries – there are inevitably some local characteristics which warrant exploration. The discussion presented here highlights the historical background to professional training, the specific professional policies and standards that guide LIS education and some of the challenges facing professional and paraprofessional education, given the changing environment of education in Australia as a whole, with some comparisons made with the New Zealand situation. While all too often library practitioners point the finger at the library educators to ‘right the wrongs’, the authors wish to reinforce the idea that the future of effective and relevant LIS education is a matter for all stakeholders in the profession: practitioners and educators, students and staff, employers and employees, with cohesion potentially offered by the professional body.

Re-thinking pedagogy for middle school students with little, no or severely interrupted schooling

The arrival of substantial cohorts of English language learners from Africa with little, no or severely interrupted schooling is requiring new pedagogic responses from teachers in Australia and other Western countries of refugee re-settlement. If the students are to have optimal educational and life chances, it is crucial for them to acquire resources for conceptually deep and critical literacy tasks while still learning basic reading and writing skills. This requires teachers to extend their pedagogic repertoires: subject area teachers must teach language and literacy alongside content; high school teachers must teach what has been thought of as primary school curriculum. The aim of this article is to describe some teacher responses to these challenges. Data are drawn from a study involving an intensive language school and three high schools, and also from the author’s experience as a homework tutor for refugees. Stand-alone basic skills programs are described, as are modifications of long-established ESL programs. It is also argued that teachers need to find ways of linking with the conceptual knowledge of students who arrive with content area backgrounds different from others in their class. Everyday life experiences prior to, and after re-settlement in the West, are rich with potential in this regard.

Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Image acquisition and manipulation protocols for CT-PET fusion to improve the accuracy of gross tumour volume localisation for 3D conformal radiotherapy for lung cancer

Aims: To develop clinical protocols for acquiring PET images, performing CT-PET registration and tumour volume definition based on the PET image data, for radiotherapy for lung cancer patients and then to test these protocols with respect to levels of accuracy and reproducibility. Method: A phantom-based quality assurance study of the processes associated with using registered CT and PET scans for tumour volume definition was conducted to: (1) investigate image acquisition and manipulation techniques for registering and contouring CT and PET images in a radiotherapy treatment planning system, and (2) determine technology-based errors in the registration and contouring processes. The outcomes of the phantom image based quality assurance study were used to determine clinical protocols. Protocols were developed for (1) acquiring patient PET image data for incorporation into the 3DCRT process, particularly for ensuring that the patient is positioned in their treatment position; (2) CT-PET image registration techniques and (3) GTV definition using the PET image data. The developed clinical protocols were tested using retrospective clinical trials to assess levels of inter-user variability which may be attributed to the use of these protocols. A Siemens Somatom Open Sensation 20 slice CT scanner and a Philips Allegro stand-alone PET scanner were used to acquire the images for this research. The Philips Pinnacle3 treatment planning system was used to perform the image registration and contouring of the CT and PET images. Results: Both the attenuation-corrected and transmission images obtained from standard whole-body PET staging clinical scanning protocols were acquired and imported into the treatment planning system for the phantom-based quality assurance study. Protocols for manipulating the PET images in the treatment planning system, particularly for quantifying uptake in volumes of interest and window levels for accurate geometric visualisation were determined. The automatic registration algorithms were found to have sub-voxel levels of accuracy, with transmission scan-based CT-PET registration more accurate than emission scan-based registration of the phantom images. Respiration induced image artifacts were not found to influence registration accuracy while inadequate pre-registration over-lap of the CT and PET images was found to result in large registration errors. A threshold value based on a percentage of the maximum uptake within a volume of interest was found to accurately contour the different features of the phantom despite the lower spatial resolution of the PET images. Appropriate selection of the threshold value is dependant on target-to-background ratios and the presence of respiratory motion. The results from the phantom-based study were used to design, implement and test clinical CT-PET fusion protocols. The patient PET image acquisition protocols enabled patients to be successfully identified and positioned in their radiotherapy treatment position during the acquisition of their whole-body PET staging scan. While automatic registration techniques were found to reduce inter-user variation compared to manual techniques, there was no significant difference in the registration outcomes for transmission or emission scan-based registration of the patient images, using the protocol. Tumour volumes contoured on registered patient CT-PET images using the tested threshold values and viewing windows determined from the phantom study, demonstrated less inter-user variation for the primary tumour volume contours than those contoured using only the patient’s planning CT scans. Conclusions: The developed clinical protocols allow a patient’s whole-body PET staging scan to be incorporated, manipulated and quantified in the treatment planning process to improve the accuracy of gross tumour volume localisation in 3D conformal radiotherapy for lung cancer. Image registration protocols which factor in potential software-based errors combined with adequate user training are recommended to increase the accuracy and reproducibility of registration outcomes. A semi-automated adaptive threshold contouring technique incorporating a PET windowing protocol, accurately defines the geometric edge of a tumour volume using PET image data from a stand alone PET scanner, including 4D target volumes.

Fear and danger in nocturnal urban environments

At the centre of this research is an ethnographic study that saw the researcher embedded within the fabric of inner city life to better understand what characteristics of user activity and interaction could be enhanced by technology. The initial research indicated that the experience of traversing the city after dark unified an otherwise divergent user group through a shared concern for personal safety. Managing this fear and danger represented an important user need. We found that mobile social networking systems are not only integral for bringing people together, they can help in the process of users safely dispersing as well. We conclude, however, that at a time when the average iPhone staggers under the weight of a plethora of apps that do everything from acting as a carpenter’s level to a pregnancy predictor, we consider the potential for the functionality of a personal safety device to be embodied within a stand alone artifact.