Sintering and Microwave Properties of Zirconium Tin Titanate Doped with Select Oxides

Zirconium tin titanate (ZST) is often used as a dielectric resonator for the fabrication of microwave devices. Pure compositions do not sinter easily by solid state sintering; therefore, sintering ZST requires sintering aids capable of creating defects that could improve diffusion processes and/or promote liquid phase sintering. The mechanisms by which the additives influence the microstructure and, consequently, the ZSTs dielectric properties are not very clear. The effects of ZnO, Bi2O3, and La2O3, on the stoichiometry and dielectric properties of ZST sintered at different temperatures were investigated in this study.

Die Festigkeit in Abhängigkeit von Scanstrategien & -optionen beim Lasersintern vom Kunststoff

Die Scanstrategie beim LS vom Kunststoff hat einen maßgeblichen Einfluss auf den Energieeintrag in das Pulverbett und somit auf die mechanischen und optischen Eigenschaften des Bauteils. Daher bieten manche Systeme die Möglichkeit verschiedener Scanstrategien oder Scanoptionen, die je nach Anwendung und gewünschten Eigenschaften ausgewählt werden können. In diesem Artikel werden die grundlegenden Aspekte der Scanstrategie beim Laser Sintern vom Kunststoff, sowie die Double-Belichtungsfunktion aufgegriffen, mit dem Ziel den genauen Einfluss der Scanstrategie bzw. Scanoptionen auf die mechanischen Eigenschaften von Thermoplasten zu ermitteln.

Ursachen für eine mangelnde Reproduzierbarkeit beim Laser-Sintern von Kunststoffbauteilen

Das Laser-Sintern hat sich in den letzten Jahren zunehmend als Kleinserienfertigungsverfahren für Kunststoffbauteile etabliert. Dennoch entspricht die Bauteilqualität aufgrund von Verzug oder mangelnder Reproduzierbarkeit der Eigenschaften oftmals nicht den Anforderungen. Ein Grund hierfür ist die inhomogene Temperaturführung während des Prozesses. So ergeben sich aufgrund einer inhomogenen Temperaturverteilung auf der Pulverbettoberfläche sowie durch unterschiedliche Abkühlgeschwindigkeiten im Pulverbett zum Teil deutliche lokale Unterschiede im Temperatur-Zeit-Verhalten. Grundlegende Untersuchungen zu diesen Effekten fehlen jedoch bislang. Im Rahmen der dargestellten Untersuchungen gilt es daher zum einen die Reproduzierbarkeit verschiedener Laser-Sinter-Anlagen in Bezug auf die mechanischen Eigenschaften, die Maßhaltigkeit und die Bauteildichte zu analysieren und zum anderen diese Ergebnisse mit den lokalen Temperatur- und Abkühlbedingungen im Pulverbett zu korrelieren. Dabei werden durch thermografische Untersuchungen die Temperaturverteilung an der Pulverbett-oberfläche charakterisiert sowie durch Einsatz entsprechender Funk-Temperatur-messsensorik die lokalen Abkühlbedingungen von Bauteilen innerhalb des Pulverbettes analysiert. Diese lokalen Temperatur- und Abkühlbedingungen sollen anschließend mit positionsabhängigen Analysen zum Bauteilschrumpf korreliert werden. Abschließend werden Optimierungspotentiale für ein neuentwickeltes Temperaturführungssystem mit homogeneren Temperatur- und Abkühlbedingungen abgeleitet.

The physical properties of sintered zirconium /

"Contract AT-30-1-gen-366."

Thoria-urania pellet preparation /

Work performed at the Sylvania-Corning Nuclear Corporation under contract AT-30 GEN-366.

Phase equilibria in the ZnO-rich area of the Fe-Zn-O system in air

The phase equilibria in the Fe-Zn-O system in the range 900-1580degreesC in air have been experimentally studied using equilibration and quenching techniques. The compositions of the phases at equilibrium were determined using electron probe X-ray microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were measured with a wet chemical analysis using the ammonium metavanadate technique. X-ray powder diffraction analysis (XRD) was used to characterise the phases. Iron oxide dissolved in zincite was found to be present principally in the ferric form. The XRD analysis and the composition measurements both indicate that zincite is the only phase stable in the ZnO-rich area in the range of conditions investigated. The solubility of the iron oxide in zincite rapidly increases at temperatures above 1200degreesC; the morphology of the zincite crystals also sharply changes between 1200 and 1300degreesC from rounded to plate-like crystals. The plate-like zincite forms a refractory network-the type of microstructure beneficial to the Imperial Smelting Process (ISP) sinter performance. The software program FactSage with a thermodynamically optimised database was used to predict phase equilibria in the Fe-Zn-O system.

The effect of the atmosphere and the role of pore filling on the sintering of aluminium

Alloys of Al-3.8Cu-1Mg-0.7Si, Al-4Cu-0.6Si-0.1Mg, Al-4Cu-1.2Mg and Al-1.9Mg-1.9Si were made using air atomised powder and conventional press-and-sinter powder metallurgy techniques. These were sintered under nitrogen with a controlled water content which varied from 3 to 630 ppm (a dew point of -69 to -25 degrees C), nitrogen-5%hydrogen, argon and argon-5% hydrogen, all at atmospheric pressure, or a vacuum of

The relationship of mineralization to petrology at Parys Mountain, Anglesey

The Lower Palaeozoic succession at Parys Mountain overlies a Precambrian basement (the Iona Series). This succession consists of Ordovician slates, overlain by, and in part interbedded with, Ordovician dacitic and rhyolitic volcanics, which in turn are unconformably overlain by Silurian slates. Both basement and Palaeozoic rocks have been deformed during Caledonian and Variscan orogenies. The resultant structure of Parys Mountain is interpreted as an east-north-easterly trending, single syncline overturned to the north. Many primary extrusive characters are retained by the volcanic rocks, despite the high degree of deformation. The lithologies and textures allow subdivision and interpretation of these rocks as dacite, lithic tuff, siliceous sinter, rhyolitic tuff, rhyolitic ignimbrite, rhyolitic tuff-lava, and rhyolitic lava. The results of 61 bulk chemical analyses are interpreted to show that the volcanism was of the orogenic calc-alkaline type from a continental margin/island arc environment. The magmas probably result from either partial melting of the crustal part of the oceanic lithosphere on a Benioff zone, or partial melting of the mantle, above a Benioff zone, under high load pressures and high water pressures. The mineral deposits are largely confined within the volcanic succession though some occur in the Ordovician and Silurian slates near to their contacts with the volcanics. The majority of the deposits form conformable lenses and tabular bodies, with subordinate deposits as veins and stockworks. The ore mineral assemblages are of chalcopyrite, galena, sphalerite, and pyrite. The general paragenetic sequence (73 sections) is pyrite--chalcopyrite--galena-sphalerite. The main mineralization episode is interpreted to be syngenetic, genetically related to the volcanism. The veins and stockworks probably result from Caledonian and Variscan remobilization of the primary mineralization. Trace element analyses (Cu, Zn, Pb, Ni, Co, Cd, Cr, Hg, Ba, Sr), on 350 specimens, detected anomalous concentrations of these elements around the mineralized zones, though some occur where no mineralization was found. The analyses also indicate a close relationship between the mineralization and the volcanic horizons, especially the siliceous sinter.

Fracture toughness of some high density PM steels

Tensile strengths, impact energies, and fracture toughness data are presented for pure Fe-0.5 C, Astaloy A with 0.2 and 0.6%C, and for Distaloy AB-0.6%C at relative densities of about 0.9, achieved by conventional pressing and sintering, and at close to 1.0, achieved by powder forging. At low relative density, properties are controlled by sizes of sinter necks; it is postulated that toughness scales as (x/a)4, x/a being the ratio of neck diameter to particle diameter. At high relative density, microvoid coalescence and good toughness is observed for low strength microstructures whereas cleavage and poor toughness is a concomitant of high strength.

Fatigue crack propagation in some PM steels

Mechanisms of fatigue crack growth have been studied for a range of PM steels at relative densities of 0.90 and 1.0, for which strength, fracture toughness, and microstructural information was also available. It is shown that the Paris exponents for steady state crack growth are between 8 and 18 when ρr is approximately 0.9 but when ρr is approximately 1.0 the exponents are between 2.6 and 4.0, i.e in the range typical of wrought steels (2-4). At both densities, threshold stress intensities are between 5.5 and 10.8 MPa m1/2 when R = 0.1. Combinations of these thresholds and yield strengths are comparable with those for wrought steels. When R = 0.8, reductions in threshold to between 2.7 and 5 MPa m1/2 are attributed to crack closure effects. At ρr = 0.90, Fe-0.5C fails by progressive rupture of sinter necks. Astaloy A, with 0.2%C and 0.6%C, and Distaloy AB-0.6C have smaller plastic zone sizes and the cracks follow more difficult paths through particles as well as necks. When ρr is approximately 1.0, fracture is partially by true fatigue modes and partly by cleavage, the bursts of cleavage being more noticeable when Kmax is high.

Stabilization of catalyst particles against sintering on oxide supports with high oxygen ion lability exemplified by Ir-catalyzed decomposition of N2O

Iridium nanoparticles deposited on a variety of surfaces exhibited thermal sintering characteristics that were very strongly correlated with the lability of lattice oxygen in the supporting oxide materials. Specifically, the higher the lability of oxygen ions in the support, the greater the resistance of the nanoparticles to sintering in an oxidative environment. Thus with γ-Al2O3 as the support, rapid and extensive sintering occurred. In striking contrast, when supported on gadolinia-ceria and alumina-ceria-zirconia composite, the Ir nanoparticles underwent negligible sintering. In keeping with this trend, the behavior found with yttria-stabilized zirconia was an intermediate between the two extremes. This resistance, or lack of resistance, to sintering is considered in terms of oxygen spillover from support to nanoparticles and discussed with respect to the alternative mechanisms of Ostwald ripening versus nanoparticle diffusion. Activity towards the decomposition of N2O, a reaction that displays pronounced sensitivity to catalyst particle size (large particles more active than small particles), was used to confirm that catalytic behavior was consistent with the independently measured sintering characteristics. It was found that the nanoparticle active phase was Ir oxide, which is metallic, possibly present as a capping layer. Moreover, observed turnover frequencies indicated that catalyst-support interactions were important in the cases of the sinter-resistant systems, an effect that may itself be linked to the phenomena that gave rise to materials with a strong resistance to nanoparticle sintering.

Desenvolvimento de um cerâmico Al2O3/TI(C,N) para uso em maquinação

O principal objetivo deste trabalho é preparar um cermeto do tipo Al2O3/Ti(C,N) com propriedades mecânicas adequadas à sua utilização na maquinação de materiais do tipo DIN ISO 513:K01-K10 e ISO H01-H10. De forma a incrementar a sinterabilidade do cermeto investigou-se o efeito da adição de dopantes metálicos, nomeadamente alumínio metálico (Al) e hidreto de titânio (TiH2) e o efeito da substituição da moagem convencional por moagem de alta energia. As variáveis das etapas principais de processamento, i.e., da moagem, prensagem e sinterização, foram selecionadas com trabalho realizado quer na Universidade de Aveiro quer na empresa Palbit. Foram preparadas três composições do cermeto Al2O3/Ti(C,N) com adições de 5%TiH2, 1%Al e 5%TiH21%Al através da moagem de alta energia. Os parâmetros de moagem, i.e. a velocidade de rotação, o rácio bolas/pó e o tempo de moagem foram otimizados para os seguintes valores: 350 rpm, 10:1 e 5 h, respetivamente. A utilização da moagem de alta energia permitiu uma redução do tamanho de partícula dos pós até aproximadamente 100 nm e a obtenção de uma boa uniformidade da distribuição das fases (Al2O3+Ti(C,N)). A etapa de conformação foi efetuada por prensagem uniaxial seguida de prensagem isostática. A avaliação da reatividade dos cermetos através de dilatometria em atmosfera de vácuo revelou que a densificação é maioritariamente realizada em estado sólido. A adição de apenas 1%Al é a menos efetiva para a densificação. Os cermetos foram sinterizados através de sinterização convencional em forno de vazio a 1650ºC e prensagem a quente (1650ºC com uma pressão uniaxial de 25 MPa). Os valores de densificação obtidos, aproximadamente 80% e 100%, respetivamente, indicam que a aplicação de pressão durante a sinterização é efetiva para atingir densificações elevadas nos compactos, compatíveis com as suas aplicações tecnológicas. As propriedades mecânicas de dureza e de tenacidade avaliadas nos três cermetos apresentaram valores aproximados de 1800-1900 HV50 para a dureza e entre 5.4 e 7.7 MPa.m1/2 para a tenacidade à fratura.

Utilização de resíduos de catalisador (ECAT) e cinzas da casca de arroz (CCA) na elaboração de vidros silicatos soda-cal destinados a embalagem

Dissertação (Mestrado em Tecnologia Nuclear)

Desenvolvimento e caracterização de filtros cerâmicos para aplicações a altas temperaturas

Ceramic filters are cellular structures that can be produced by various techniques, among which we highlight the replication method, or method of polymeric sponge. This method consists of impregnating polymeric foam with ceramic slurry, followed by heat treatment, where will occur decomposition of organic material and the sinter of the ceramic material, resulting in a ceramic whose structure is a replica of the impregnated sponge. Ceramic filters have specific properties that make this type of material very versatile, used in various technological applications such as filters for molten metals and burners, make these materials attractive candidates for high temperature applications. In this work we studied the systems Al2O3-LZSA ceramic filters processed in the laboratory, and commercial Al2O3-SiC ceramics filters, both obtained by the replica method, this work proposes the thermal and mechanical characterization. The sponge used in the processing of filters made in the laboratory was characterized by thermogravimetric analysis. The ceramic filters were characterized by compressive strength, flexural strength at high temperatures, thermal shock, permeability and physical characterization (density and porosity) and microstructural (MEV and X-rays). From the results obtained, the analysis was made of the mechanical behavior of these materials, comparing the model proposed by Gibson and Ashby model and modified the effective area and the tension adjusted, where the modified model adapted itself better to the experimental results, representing better the mechanical behavior of ceramic filters obtained by the replica method

Comportamento da adição do carbeto de nióbio (nBC) na matriz metálica do aço ferrítico 15kH2mfa

The 15Kh2MFA steel is a kind of Cr-Mo-V family steels and can be used in turbines for energy generation, pressure vessels, nuclear reactors or applications where the range of temperature that the material works is between 250 to 450°C. To improve the properties of these steels increasing the service temperature and the thermal stability is add a second particle phase. These particles can be oxides, carbides, nitrites or even solid solution of some chemical elements. On this way, this work aim to study the effect of addition of 3wt% of niobium carbide in the metallic matrix of 15Kh2MFA steel. Powder metallurgy was the route employed to produce this metallic matrix composite. Two different milling conditions were performed. Condition 1: milling of pure 15Kh2MFA steel and condition 2: milling of 15Kh2MFA steel with addition of niobium carbide. A high energy milling was carried out during 5 hours. Then, these two powders were sintered in a vacuum furnace (10-4torr) at 1150 and 1250°C during 60 minutes. After sintering the samples were normalized at 950°C per 3 minutes followed by air cooling to obtain a desired microstructure. Results show that the addition of niobium carbide helps to mill faster the particles during the milling when compared with that steel without carbide. At the sintering, the niobium carbide helps to sinter increasing the density of the samples reaching a maximum density of 7.86g/cm³, better than the melted steel as received that was 7,81g/cm³. In spite this good densification, after normalizing, the niobium carbide don t contributed to increase the microhardness. The best microhardness obtained to the steel with niobium carbide was 156HV and to pure 15Kh2MFA steel was 212HV. It happened due when the niobium carbide is added to the steel a pearlitic structure was formed, and the steel without niobium carbide submitted to the same conditions reached a bainitic structure