A novel single-phase hpf hybrid rectifier suitable for front-end trolleybus systems

This paper proposal presents the development and the experimental analysis of a new single-phase hybrid rectifier structure with high power factor (PF) and low harmonic distortion of current (THDI), suitable for application in traction systems of electrical vehicles pulled by electrical motors (trolleybus), which are powered by urban distribution network. This front-end rectifier structure is capable of providing significant improvements in trolleybuses systems and in the urban distribution network costs, and efficiency. The proposed structure is composed by an ordinary single-phase diode rectifier with parallel connection of a switched converter. It is outlined that the switched converter is capable of composing the input line current waveform assuring high power factor (HPF) and low THDI, as well as ordinary front-end converter. However, the power rating of the switched converter is about 34% of the total output power, assuring robustness and reliability. Therefore, the proposed structure was named single-phase HPF hybrid rectifier. A prototype rated at 15kW was developed and analyzed in laboratory. It was found that the input line current harmonic spectrum is in accordance with the harmonic limits imposed by IEC61000-3-4. The principle of operation, the mathematical analysis, the PWM control strategy, and experimental results of a 15kW prototype are also presented in this paper. © 2009 IEEE.

Harmonic content identification based on neural method for single phase power systems

An alternative method is presented in this paper to identify the harmonic components of non-linear loads in single phase power systems based on artificial neural networks. The components are identified by analyzing the single phase current waveform in time domain in half-cycle of the ac voltage source. The proposed method is compared to the fast Fourier transform. Simulation and experimental results are presented to validate the proposed approach.

Optimized dynamic response of parallel operation of two single phase inverters based on evolutionary theory

In this work it is proposed an optimized dynamic response of parallel operation of two single-phase inverters with no control communication. The optimization aims the tuning of the slopes of P-ω and Q-V curves so that the system is stable, damped and minimum settling time. The slopes are tuned using an algorithm based on evolutionary theory. Simulation and experimental results are presented to prove the feasibility of the proposed approach. © 2010 IEEE.

Single phase a-plane MgZnO epilayers for UV optoelectronics: substitutional behaviour of Mg at large contents

High quality 1 μm thick a-plane MgxZn1−xO layers were produced by molecular beam epitaxy with Mg contents higher than 50%. Resonant Rutherford backscattering spectrometry combined with ion channeling revealed a uniform growth in both composition and atomic order. The lattice-site location of Mg, Zn and O elements was determined independently, proving the substitutional behaviour of Mg in Zn-sites of the wurtzite lattice. X-Ray diffraction pole figure analysis also confirms the absence of phase separation. Optical properties at such high Mg contents were studied in Schottky photodiodes.

Operator's, organizational, direct support and general support maintenance manual : air conditioner, horizontal, compact, 9,000 Btu/hr, 115 volt, single phase 50/60 hertz, model A9KH-115P, NSN 4120-01-136-2214.

"31 October 1986."

Organizational maintenance repair parts and special tools list : air conditioning units, electric motor driven, 9,000 Btu/hr, vertical compact, 115 volt, single phase, 50/60 cycle (Therm-Air Manufacturing Co. model CV-9-1-15-60) FSN 4120-935-1609; 9,000 Btu/hr, vertical compact, 230 volt, three phase, 50/60 cycle ....

"February 1970."

Organizational maintenance repair parts and special tools list : air conditioner, vertical, compact, self-contained, air cooled, electric motor driven, 115 volts, A.C. 50/60 hertz, single phase, 9,000 Btu/hr cooling, 6,000 Btu/hr heating (Harvey W. Hottel model CV-9-5/6-15), FSN 4120-935-1609.

"September 1974."

Operators, organizational, direct support, and general support maintenance manual : water purification unit, 420 gallons per hour, electric driven, 115V, single phase, 60 hertz 1/20 to 1 1/4 hp (Litton Systems, Inc. model LPU 420-1), FSN 4610-012-5490.

"1 October 1969"--P. i.

Operator's manual : grinding kit, valve seat, electric 35 degree angle type concentric drive, 1/4 horsepower, AC/DC, single phase, 115-volt, 14000 RPM rated no load speed (K.O. Lee Company model P300BB) (4910-060-9983) and (K.O. Lee Company model P300BB-M2) (4910-473-6437).

"February 1965."

Operator and organizational maintenance manual (including repair parts and special tool lists) : tester, engine distributor, bench type, 6, 12, and 24-volt distributors, single-phase, 60-cycle, 115-volt (Heyer Products Company Inc., model 168) (4910-392-2939).

"30 September 1963."

Operator's, manual : milling machine, ram type, swivel head, plain table, power feed, 1 1/2 horsepower, 110-volt, 60-cycle, single-phase (Van Norman Machine Company models IR-3-22 and IRQ-3-22) (3417-624-4254).

"March 1967."

Organizational maintenance manual (including repair parts and special tools lists) : milling-grinding-drilling-slotting attachment, 115/230-volt, 60-cycle, single-phase, 1/3 horsepower (Dumore Company model 827401) ...

"January 1965."

Organizational maintenance manual : lathe, engine, bench mounted, solid bed type, 10 inch swing, no. 2 Morse taper center, 1-3/8 spindle hole, 110-volts, 60 cycle, single phase 3/4-horsepower, w/Army dwg. no. 7550151 bench (standard-modern tool series 2,000 model, 11 inch) (3416-517-0955).

"November 1965."

Operator's manual : boring machine, engine cylinder, portable, 3 1/2 to 7 1/2 bore diameter, 18 inch depth of bore, 110-volt, 60-cycle, single-phase (Cedar Rapids Engineering Company model FL) (4910-223-9734).

"November 1965."

Operator's manual : grinding machine, machine tool attachment, internal and external grinding, 5" maximum external diameter wheel, 1/4" minimum internal diameter wheel, 4,600 to 42,400 rpm spindle speed, 1/2 hp, AC/DC, 115 V, 60-C, single phase (Dumore series 5) ...

"October 1967."