Estudo comparativo da injeção de água usando poços verticais e horizontais

Oil recovery using waterflooding has been until now the worldwide most applied method, specially for light oil recovery, its success is mainly because of the low costs involved and the facilities of the injection process. The Toe- To-Heel Waterflooding TTHWTM method uses a well pattern of vertical injector wells completed at the bottom of the reservoir and horizontal producer wells completed at the top of it. The main producing mechanism is gravitational segregation in short distance. This method has been studied since the early 90´s and it had been applied in Canada with positive results for light heavy oils, nevertheless it hasn´t been used in Brazil yet. In order to verify the applicability of the process in Brazil, a simulation study for light oil was performed using Brazilian northwest reservoirs characteristics. The simulations were fulfilled using the STARS module of the Computer Modelling Group Software, used to perform improved oil recovery studies. The results obtained in this research showed that the TTHWTM well pattern presented a light improvement in terms of recovery factor when compared to the conventional 5- Spot pattern, however, it showed lower results in the economic evaluation

Estudo dos parâmetros operacionais do processo de combustão in situ em reservatório de petróleo pesado

The occurrence of heavy oil reservoirs have increased substantially and, due to the high viscosity characteristic of this type of oil, conventional recovery methods can not be applied. Thermal methods have been studied for the recovery of this type of oil, with a main objective to reduce its viscosity, by increasing the reservoir temperature, favoring the mobility of the oil and allowing an increasing in the productivity rate of the fields. In situ combustion (ISC) is a thermal recovery method in which heat is produced inside the reservoir by the combustion of part of the oil with injected oxygen, contrasting with the injection of fluid that is heated in the surface for subsequent injection, which leads to loss heat during the trajectory to the reservoir. The ISC is a favorable method for recovery of heavy oil, but it is still difficult to be field implemented. This work had as an objective the parametric analysis of ISC process applied to a semi-synthetic reservoir with characteristics of the Brazilian Northeast reservoirs using vertical production and vertical injection wells, as the air flow injection and the wells completions. For the analysis, was used a commercial program for simulation of oil reservoirs using thermal processes, called Steam, Thermal and Advanced Processes Reservoir Simulator (STARS) from Computer Modelling Group (CMG). From the results it was possible to analyze the efficiency of the ISC process in heavy oil reservoirs by increasing the reservoir temperature, providing a large decrease in oil viscosity, increasing its mobility inside the reservoir, as well as the improvement in the quality of this oil and therefore increasing significantly its recovered fraction. Among the analyzed parameters, the flow rate of air injection was the one which had greater influence in ISC, obtaining higher recovery factor the higher is the flow rate of injection, due to the greater amount of oxygen while ensuring the maintenance of the combustion front

Regras de operação do reservatório de Magos para controlo de cheias

Face à Directiva 2007/60/CE relativa à avaliação e gestão do risco de inundações, ao Decreto-Lei nº 344/2007 que aprova o Regulamento de Segurança de Barragens, ao aumento de áreas urbanizadas e às projecções dos modelos de clima para o fim do século, que apontam para o aumento da frequência e da intensidade da ocorrência de inundações causadas por eventos de precipitação intensa de curta duração, é crucial a definição de regras de operação nos reservatórios com controlo de cheias. O Reservatório de Magos pertence à bacia hidrográfica do rio Tejo, está situado no Concelho de Salvaterra de Magos e tem como usos principais a rega e o controlo de cheias. Este trabalho tem como objecto de estudo a definição das regras de operação (restrição no caudal descarregado) do Reservatório de Magos para controlo de cheias no troço a jusante. São aplicados o modelo hidrológico HEC-HMS 3.1.0, o modelo hidráulico HEC-RAS 3.1.3 e o modelo de simulação de reservatórios HEC-ResSim 3.O para o cálculo do hidrograma de cheia, da zona inundável e para simulação do balanço de água no reservatório, respectivamente. Como resultado são apresentadas as regras de operação (caudal máximo e mínimo a descarregar) do Reservatório de Magos para controlo da zona inundável a jusante, no caso de um evento de cheia. /ABSTRACT: Based on the Directive 2007/60/CE related to the Assessment and Management of Flood Risks, on the Decree-Law n. o 344/2007 which approves the Regulation for Dam Safety, the increased urban areas and to the projections of climate models by the end of the century which is pointing to an increased frequency and intensity of occurrence of floods caused by intense rainfall events of short duration, establishing rules of operation for flood control in reservoirs becomes crucial. The Magos Reservoir belongs to the river Tagus basin, located in the county of Salvaterra de Magos and has as its main uses the irrigation and flood control. This study aims to establish the rules of operation (flow discharged restriction) of the Reservoir of Magos for flood control in the downstream reach. The methodology used in the present work includes the application of the Hydrological model HEC-HMS 3.1.0, the Hydraulic model HEC-RAS 3.1.3 and a reservoir simulation model HEC-ResSim 3.0 to calculate the hydrograph of peak discharge, floodplain zone and simulate reservoir operations, respectively. As a result, the rules of operation (maximum flow and minimum discharge) of Magos Reservoir for flood control in a downstream reach in case of flood event are presented.

Simulação de estruturas meandriformes por objectos e estatísticas multiponto e avaliação da porosidade – aplicação a reservatórios siliciclásticos

Neste trabalho apresenta-se uma metodologia destinada a simular a morfologia e a porosidade de canais de areia em reservatórios fluviais. Como informação de partida utilizam-se um ou vários canais de areia de treino, em estrutura vectorial, que sejam representativos do reservatório, e leis de distribuição das dimensões largura e profundidade dos canais. Para a simulação da morfologia dos canais de areia, são calculados os ângulos azimutais de todos os segmentos de recta das linhas poligonais que constituem os canais de treino, a que se segue a codificação em classes de azimute e a determinação de estatísticas multiponto destas classes. Seguidamente, faz-se a simulação estocástica dos novos canais no volume do reservatório, ou seja, são geradas novas linhas poligonais condicionadas às estatísticas multiponto, a que se associam as dimensões largura e profundidade. Este algoritmo multiponto é muito eficiente, porque é a 1D, e contorna a problemática da variável azimute ser do tipo circular. A avaliação da porosidade é feita em simultâneo na conversão do modelo vectorial da morfologia dos canais de areia para o modelo matricial da malha de blocos do reservatório. Para cada bloco reservatório é contabilizada a proporção de não canal / canal e das fácies conforme um modelo conceptual de zonamento na secção do canal. A estimativa da porosidade média de cada bloco do reservatório é obtida pela soma do produto da proporção de cada fácies pela respectiva porosidade de referência. Para ilustrar as potencialidades da metodologia proposta apresenta-se um caso de estudo com dados sintéticos. De acordo com critérios geológicos e estratigráficos, consideraram-se quatro fácies na secção do canal que são discriminadas lateralmente e em profundidade por valores de referência de porosidade. O algoritmo de simulação morfológica capturou adequadamente a morfologia das imagens de treino e gerou várias imagens equiprováveis que depois foram convertidas em porosidade.

Reservatórios turbidíticos – simulação da morfologia por estatísticas multiponto e avaliação das propriedades petrofísicas

Esta dissertação apresenta uma metodologia original para simular a morfologia e as propriedades petrofísicas de reservatórios de hidrocarbonetos em sistemas de canais turbidíticos. Estes sistemas são constituídos por complexos, ou seja, conjuntos de canais de arquitetura meandriforme, e são considerados importantes alvos para a indústria petrolífera. A simulação da morfologia divide-se em duas partes, primeiramente é simulada a trajetória do complexo e depois são simuladas as trajetórias dos canais propriamente ditos condicionadas à trajetória do complexo. O algoritmo de simulação utiliza as classes de ângulos azimutais de linhas poligonais de treino como uma variável aleatória. As trajetórias são simuladas também como linhas poligonais, condicionais a estatísticas multiponto das trajetórias de treino e a pontos de controlo. As estatísticas multiponto são organizadas em árvore, que guarda sequências de classes de orientação que ocorrem na trajetória de treino e as respetivas probabilidades de ocorrência. Para avaliar as propriedades petrofísicas, o modelo morfológico das trajetórias é convertido para uma malha de blocos de alta resolução, identificando-se, em cada bloco, a fácies preponderante de acordo com um modelo conceptual de zonamento da secção dos canais. A conversão prioriza os canais mais recentes (do topo) sobre os mais antigos (da base). A cada fácies é associada uma lei de distribuição da porosidade e permeabilidade, assim são geradas imagens destas propriedades petrofísicas por Simulação Sequencial Direta com histogramas locais. Finalmente, o número de blocos da malha é reduzido por upscaling e as simulações são ordenadas para poderem ser utilizadas nos simuladores de fluxo. Para ilustrar a metodologia, utilizaram-se imagens de sísmica 3D de um reservatório turbidítico na Bacia do Baixo Congo para extrair leis de distribuição das dimensões dos canais e trajetórias de treino. Os resultados representam corretamente a arquitetura complexa destes sistemas.

Tratamento de água subterrânea contaminada por compostos orgânicos voláteis: considerações sobre o dimensionamento e simulação de colunas de arrastamento por ar

A água subterrânea representa cerca de 97% de água doce existente na terra. A sua global disponibilidade, aliada às suas qualidades naturais e à inexistência de fontes superficiais de abastecimento em largas áreas continentais, tem feito, ao longo dos tempos, com que a sua utilização, nomeadamente doméstica, tenha vindo a ser uma constante. No entanto, estes tipos de reservatórios subterrâneos - aquíferos - são de uma vulnerabilidade extrema no que se refere à contaminação por poluentes. Não só são facilmente contamináveis, como se tornam difícil e morosamente recuperáveis. As normas que definem a qualidade de determinada água impõem limitações específicas para os determinados usos (no nosso país vigora o Dec.Lei nº74/90 de 7 de Março).

Instrumentalização do Propagar MOO com ferramentas de planejamento do uso da água e de análise da simulação através da utilização da linguagem Pascal Script

A simulação é uma das ferramentas mais utilizadas para a aplicação da análise sistêmica nos mais diversos estudos. Ao longo do tempo, vários modelos foram desenvolvidos para representar sistemas de recursos hídricos, utilizando a simulação. Dentre esses modelos, está o Propagar MOO, que simula a propagação de vazões em uma bacia hidrográfica, submetida à decisões operacionais de suprimento de demandas e de operação de reservatórios, introduzidas pelo usuário através de rotinas escritas na linguagem de programação Pascal Script. A utilização eficiente dessas rotinas permite ao usuário ampliar a capacidade e flexibilidade do modelo na representação de um sistema hídrico. Com o objetivo de contribuir na ampliação da flexibilidade do modelo Propagar MOO e de sua aplicabilidade à modelagem de sistemas de recursos hídricos em geral, bem como facilitar o estudo da linguagem de programação Pascal Script e motivar os profissionais da área no desenvolvimento de novas rotinas aplicadas ao modelo, foram implementadas, através do presente trabalho, rotinas genéricas contendo estratégias de planejamento do uso da água e de operação de reservatórios, bem como ferramentas para analisar seus resultados. Para ampliar essa contribuição, foi aprimorada a possibilidade de simulação da geração de energia hidrelétrica em pontos de uma rede hidrográfica, com a criação de novas ferramentas para esse fim, na estrutura interna do modelo. Por fim, para que o próprio usuário pudesse construir ferramentas para auxiliar na verificação dos resultados obtidos nas simulações, esse estudo apresenta a implementação de rotinas de uso geral para servir como exemplos de ferramentas de análise de dados.

Eutrofização e capacidade de carga de fósforo de seis reservatórios a bacia do Rio Seridó, região semi-árida do Estado do RN

The eutrofization is a natural process of accumulation of nutrients in aquatic´s body that it has been accelerated for the human´s actives, mainly the related with the activities of camp, industrial and the inadequate disposition of the domestic sewage. The enrichment of the aquatic´s body with nutrients, mainly the nitrogen and the phosphorus, and the consequent proliferation of algae and Cyanobacteria can commit the quality of the water for the public provisioning, for the fish farming and for other ends. The problem becomes more critical when there is a shortage of water naturally as in the semi-arid area of the Brazilian northeast. Before that problem this work had as objective evaluates the trophic state of six reservoirs of the basin of River Seridó of Rio Grande of Norte and also estimate the capacity of load of match of the reservoir and risk probabilities based on the established limits by the resolution Conama 357/05. The results demonstrate that the six reservoirs are eutrofization, with concentration of total phosphorus and cloro a in the water upster to 50 e 12 μg l-1. The results show that space homogeneity exists in the state trophic of the reservoirs, but a significant variation interanual in function of the increase of the concentrations of nutrients and decrease of the transparency of the water with the reduction of the body of water accumulated in the reservoirs.The results of the simulation risk estocastic show that the reservoirs could receive annually from 72 to 216 Kg of P, assuming a risk of 10% of increasing in more than 30 μg l-1 the annual medium concentrations of total match in the water of these reservoirs. This load could be high in until 360 kg of P a year in case the managers assume a risk of 10% of increasing in more than 50 μg l-1 the annual medium concentrations of total phosphorus in the waters of these reservoirs

Análise paramétrica da simulação composicional do processo de Drenagem Gravitacional Assistida por Gás (GAGD)

In Brazil and around the world, oil companies are looking for, and expected development of new technologies and processes that can increase the oil recovery factor in mature reservoirs, in a simple and inexpensive way. So, the latest research has developed a new process called Gas Assisted Gravity Drainage (GAGD) which was classified as a gas injection IOR. The process, which is undergoing pilot testing in the field, is being extensively studied through physical scale models and core-floods laboratory, due to high oil recoveries in relation to other gas injection IOR. This process consists of injecting gas at the top of a reservoir through horizontal or vertical injector wells and displacing the oil, taking advantage of natural gravity segregation of fluids, to a horizontal producer well placed at the bottom of the reservoir. To study this process it was modeled a homogeneous reservoir and a model of multi-component fluid with characteristics similar to light oil Brazilian fields through a compositional simulator, to optimize the operational parameters. The model of the process was simulated in GEM (CMG, 2009.10). The operational parameters studied were the gas injection rate, the type of gas injection, the location of the injector and production well. We also studied the presence of water drive in the process. The results showed that the maximum vertical spacing between the two wells, caused the maximum recovery of oil in GAGD. Also, it was found that the largest flow injection, it obtained the largest recovery factors. This parameter controls the speed of the front of the gas injected and determined if the gravitational force dominates or not the process in the recovery of oil. Natural gas had better performance than CO2 and that the presence of aquifer in the reservoir was less influential in the process. In economic analysis found that by injecting natural gas is obtained more economically beneficial than CO2

Estudo paramétrico do processo de injeção de solventes em poços horizontais para reservatórios de óleos pesados

The world has many types of oil that have a range of values of density and viscosity, these are characteristics to identify whether an oil is light, heavy or even ultraheavy. The occurrence of heavy oil has increased significantly and pointing to a need for greater investment in the exploitation of deposits and therefore new methods to recover that oil. There are economic forecasts that by 2025, the heavy oil will be the main source of fossil energy in the world. One such method is the use of solvent vaporized VAPEX which is known as a recovery method which consists of two horizontal wells parallel to each other, with a gun and another producer, which uses as an injection solvent that is vaporized in order to reduce the viscosity of oil or bitumen, facilitating the flow to the producing well. This method was proposed by Dr. Roger Butler, in 1991. The importance of this study is to analyze how the influence some operational reservoir and parameters are important in the process VAPEX, such as accumulation of oil produced in the recovery factor in flow injection and production rate. Parameters such as flow injection, spacing between wells, type of solvent to be injected, vertical permeability and oil viscosity were addressed in this study. The results showed that the oil viscosity is the parameter that showed statistically significant influence, then the choice of Heptane solvent to be injected showed a greater recovery of oil compared to other solvents chosen, considering the spacing between the wells was shown that for a greater distance between the wells to produce more oil

Estudo da injeção de CO2 em reservatórios carbonáticos de dupla-porosidade

As rochas carbonáticas ocupam, numa visão global, um expressivo volume da crosta terrestre. De maneira geral, pode-se dizer que essas rochas estão presentes nas diversas unidades litoestatigráficas da Terra. Os reservatórios carbonáticos são reservas naturalmente fraturadas que exigem uma abordagem diferenciada na modelagem em programas de simulação numérica. Os modelos de dupla porosidade são descritos por funções de tranferências que modelam o fluxo de óleo entre matriz e fraturas. Em um reservatório carbonático naturalmente fraturado o sistema de fraturas é determinante no escoamento de fluidos dentro da reserva. Os maiores reservatórios carbonáticos do mundo estão situados no Oriente Médio e na América do Norte. As maiores reservas de óleo brasileiras encontradas neste tipo de reservatório estão localizadas nos campos do Pré-Sal. No Pré-Sal, um volume significativo de dióxido de carbono é produzido juntamente com o óleo. A disponibilidade de um volume consideravél de dióxido de carbono derivado da produção de óleo no Pré-Sal favorece a utilização dos processos de EOR (Enhanced Oil Recovery) por injeção de gás. O processo de injeção de dióxido de carbono vem sendo utilizado em uma grande quantidade de projetos pelo mundo. A afinidade existente entre o óleo e o dióxido de carbono causa uma frente miscível entre as duas fases causando inchamento e vaporização do óleo dentro do reservatório. Para o estudo, foi utilizado um modelo base de reservatório de dupla-porosidade, desenvolvido pela CMG para o 6° Projeto de Soluções Comparativas da SPE, que modela sistemas de fraturas e de matriz e a tranferência de massa fluida entre elas, características de reservatórios naturalmente fraturados. Foi feita uma análise da injeção de diferentes vazões de dióxido de carbono no modelo base e em modelos semelhantes, com aumento e redução de 5 e 0.5 pontos nas propriedades de porosidade e permeabilidade da matriz, respectivamente, tendo a produção de óleo como resultado. A injeção de 25 milhões de pés cúbicos por dia de CO2 foi a vazão que obteve a melhor fator de recuperação

Análise paramétrica do método de injeção alternada de água e CO2(WAG) em reservatórios de petróleo

After the decline of production from natural energy of the reservoir, the methods of enhanced oil recovery, which methods result from the application of special processes such as chemical injection, miscible gases, thermal and others can be applied. The advanced recovery method with alternating - CO2 injection WAG uses the injection of water and gas, normally miscible that will come in contact with the stock oil. In Brazil with the discovery of pre-salt layer that gas gained prominence. The amount of CO2 present in the oil produced in the pre-salt layer, as well as some reservoirs is one of the challenges to be overcome in relation to sustainable production once this gas needs to be processed in some way. Many targets for CO2 are proposed by researchers to describe some alternatives to the use of CO2 gas produced such as enhanced recovery, storage depleted fields, salt caverns storage and marketing of CO2 even in plants. The largest oil discoveries in Brazil have recently been made by Petrobras in the pre -salt layer located between the states of Santa Catarina and Espírito Santo, where he met large volumes of light oil with a density of approximately 28 ° API, low acidity and low sulfur content. This oil that has a large amount of dissolved CO2 and thus a pioneering solution for the fate of this gas comes with an advanced recovery. The objective of this research is to analyze which parameters had the greatest influence on the enhanced recovery process. The simulations were performed using the "GEM" module of the Computer Modelling Group, with the aim of studying the advanced recovery method in question. For this work, semi - synthetic models were used with reservoir and fluid data that can be extrapolated to practical situations in the Brazilian Northeast. The results showed the influence of the alternating injection of water and gas on the recovery factor and flow rate of oil production process, when compared to primary recovery and continuous water injection or continuous gas injection

Análise de viabilidade de injeção de fluidos alternativos ao vapor em reservatórios de óleo pesado

Many of hydrocarbon reserves existing in the world are formed by heavy oils (°API between 10 and 20). Moreover, several heavy oil fields are mature and, thus, offer great challenges for oil industry. Among the thermal methods used to recover these resources, steamflooding has been the main economically viable alternative. Latent heat carried by steam heats the reservoir, reducing oil viscosity and facilitating the production. This method has many variations and has been studied both theoretically and experimentally (in pilot projects and in full field applications). In order to increase oil recovery and reduce steam injection costs, the injection of alternative fluid has been used on three main ways: alternately, co-injected with steam and after steam injection interruption. The main objective of these injection systems is to reduce the amount of heat supplied to the reservoir, using cheaper fluids and maintaining the same oil production levels. This works discusses the use of carbon dioxide, nitrogen, methane and water as an alternative fluid to the steam. The analyzed parameters were oil recoveries and net cumulative oil productions. The reservoir simulation model corresponds to an oil reservoir of 100 m x 100 m x 28 m size, on a Cartesian coordinates system (x, y and z directions). It is a semi synthetic model with some reservoir data similar to those found in Brazilian Potiguar Basin. All studied cases were done using the simulator STARS from CMG (Computer Modelling Group, version 2009.10). It was found that waterflood after steam injection interruption achieved the highest net cumulative oil compared to other fluids injection. Moreover, it was observed that steam and alternative fluids, co-injected and alternately, did not present increase on profitability project compared with steamflooding

Simulação do escoamento multifásico no interior de bombas de cavidades progressivas metálicas

The progressing cavity pumping (PCP) is one of the most applied oil lift methods nowadays in oil extraction due to its ability to pump heavy and high gas fraction flows. The computational modeling of PCPs appears as a tool to help experiments with the pump and therefore, obtain precisely the pump operational variables, contributing to pump s project and field operation otimization in the respectively situation. A computational model for multiphase flow inside a metallic stator PCP which consider the relative motion between rotor and stator was developed in the present work. In such model, the gas-liquid bubbly flow pattern was considered, which is a very common situation in practice. The Eulerian-Eulerian approach, considering the homogeneous and inhomogeneous models, was employed and gas was treated taking into account an ideal gas state. The effects of the different gas volume fractions in pump volumetric eficiency, pressure distribution, power, slippage flow rate and volumetric flow rate were analyzed. The results shown that the developed model is capable of reproducing pump dynamic behaviour under the multiphase flow conditions early performed in experimental works

Incorporação do vínculo de suavidade no ajuste de histórico de reservatórios de petróleo

The history match procedure in an oil reservoir is of paramount importance in order to obtain a characterization of the reservoir parameters (statics and dynamics) that implicates in a predict production more perfected. Throughout this process one can find reservoir model parameters which are able to reproduce the behaviour of a real reservoir.Thus, this reservoir model may be used to predict production and can aid the oil file management. During the history match procedure the reservoir model parameters are modified and for every new set of reservoir model parameters found, a fluid flow simulation is performed so that it is possible to evaluate weather or not this new set of parameters reproduces the observations in the actual reservoir. The reservoir is said to be matched when the discrepancies between the model predictions and the observations of the real reservoir are below a certain tolerance. The determination of the model parameters via history matching requires the minimisation of an objective function (difference between the observed and simulated productions according to a chosen norm) in a parameter space populated by many local minima. In other words, more than one set of reservoir model parameters fits the observation. With respect to the non-uniqueness of the solution, the inverse problem associated to history match is ill-posed. In order to reduce this ambiguity, it is necessary to incorporate a priori information and constraints in the model reservoir parameters to be determined. In this dissertation, the regularization of the inverse problem associated to the history match was performed via the introduction of a smoothness constraint in the following parameter: permeability and porosity. This constraint has geological bias of asserting that these two properties smoothly vary in space. In this sense, it is necessary to find the right relative weight of this constrain in the objective function that stabilizes the inversion and yet, introduces minimum bias. A sequential search method called COMPLEX was used to find the reservoir model parameters that best reproduce the observations of a semi-synthetic model. This method does not require the usage of derivatives when searching for the minimum of the objective function. Here, it is shown that the judicious introduction of the smoothness constraint in the objective function formulation reduces the associated ambiguity and introduces minimum bias in the estimates of permeability and porosity of the semi-synthetic reservoir model