Power Efficient Redundant Execution for Chip Multiprocessor

This paper describes the design of a power efficient microarchitecture for transient fault detection in chip multiprocessors (CMPs) We introduce a new per-core dynamic voltage and frequency scaling (DVFS) algorithm for our architecture that significantly reduces power dissipation for redundant execution with a minimal performance overhead. Using cycle accurate simulation combined with a simple first order power model, we estimate that our architecture reduces dynamic power dissipation in the redundant core by an mean value of 79% and a maximum of 85% with an associated mean performance overhead of only 1:2%

Energy-efficient redundant execution for chip multiprocessors

Relentless CMOS scaling coupled with lower design tolerances is making ICs increasingly susceptible to wear-out related permanent faults and transient faults, necessitating on-chip fault tolerance in future chip microprocessors (CMPs). In this paper, we describe a power-efficient architecture for redundant execution on chip multiprocessors (CMPs) which when coupled with our per-core dynamic voltage and frequency scaling (DVFS) algorithm significantly reduces the energy overhead of redundant execution without sacrificing performance. Our evaluation shows that this architecture has a performance overhead of only 0.3% and consumes only 1.48 times the energy of a non-fault-tolerant baseline.

A magnetic micro-manipulator for application of three dimensional forces

Magnetic manipulation finds diverse applications in actuation, characterization, and manipulation of micro-and nano-scale samples. This paper presents the design and development of a novel magnetic micro-manipulator for application of three-dimensional forces on a magnetic micro-bead. A simple analytical model is proposed to obtain the forces of interaction between the magnetic micromanipulator and a magnetic micro-bead. Subsequently, guidelines are proposed to perform systematic design and analysis of the micro-manipulator. The designed micro-manipulator is fabricated and evaluated. The manipulator is experimentally demonstrated to possess an electrical bandwidth of about 1 MHz. The ability of the micro-manipulator to apply both in-plane and out-of-plane forces is demonstrated by actuating permanent-magnet micro-beads attached to micro-cantilever beams. The deformations of the micro-cantilevers are also employed to calibrate the dependence of in-plane and out-of-plane forces on the position of the micro-bead relative to the micro-manipulator. The experimentally obtained dependences are found to agree well with theory. (C) 2015 AIP Publishing LLC.

Three-degree-of-freedom Parallel Manipulator to Track the Sun for Concentrated Solar Power Systems

In concentrated solar power(CSP) generating stations, incident solar energy is reflected from a large number of mirrors or heliostats to a faraway receiver. In typical CSP installations, the mirror needs to be moved about two axes independently using two actuators in series with the mirror effectively mounted at a single point. A three degree-of-freedom parallel manipulator, namely the 3-RPS parallel manipulator, is proposed to track the sun. The proposed 3-RPS parallel manipulator supports the load of the mirror, structure and wind loading at three points resulting in less deflection, and thus a much larger mirror can be moved with the required tracking accuracy and without increasing the weight of the support structure. The kinematics equations to determine motion of the actuated prismatic joints in the 3-RPS parallel manipulator such that the sun's rays are reflected on to a stationary receiver are developed. Using finite element analysis, it is shown that for same sized mirror, wind loading and maximum deflection requirement, the weight of the support structure is between 15% and 60% less with the 3-RPS parallel manipulator when compared to azimuth-elevation or the target-aligned configurations.

3自由度并联柔索驱动变刚度操作臂的刚度控制

利用柔索的弹性及驱动冗余性构造了一种3自由度并联柔索驱动变刚度操作臂,在静力学与刚度分析的基础上,进行刚度控制研究。首先,将柔索驱动力映射到关节空间,并分析等效关节力与柔索张力和外力的关系, 提出该操作臂的三维力矢量闭合原理。根据微分变换原理进行刚度分析,得到关节刚度矩阵及操作手刚度矩阵, 并进行数值算例分析,结果表明:刚度与柔索的张力有关,调节柔索张力可以改变系统刚度。最后,采用位置与张力混合控制的策略,对该变刚度操作臂进行了刚度控制,并进行了仿真验证。

一种7DOF冗余手臂构形的运动学与动力学特性研究

冗余度机构具有高度的灵活性和避障能力,利用冗余自由度可以改善仿人机器人手臂的运动性能。以实现人体手臂的运动特性和操作灵活性为目标,研制了一种7DOF冗余仿人机器人手臂,根据冗余手臂的机构学特点,研究了手臂的运动学和动力学性能,并在工作空间、肘部关节的自运动能力以及手臂自重引起的关节重力矩等方面与其它两种典型的冗余手臂构形进行了比较分析。

基于模糊推理水下作业系统运动控制研究

水下作业系统是运动学冗余系统,本文将模糊推理方法融入基于任务优先运动学控制算法,对系统载体与机械手进行协调运动分配,同时对系统多个任务进行优化。通过带有3自由度水下机械手的水下作业系统进行算例仿真研究,说明运动控制算法的有效性。