Influence of cassette type on the DQE of CR systems.

In our recent paper by Monnin et al. [Med. Phys. 33, 411-420 (2006)], an objective analysis of the relative performance of a computed radiography (CR) system using both standard single-side (ST-VI) and prototype dual-side read (ST-BD) plates was reported. The presampled modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE) for the systems were determined at three different beam qualities representative of paediatric chest radiography, at an entrance detector air kerma of 5 microGy. Experiments demonstrated that, compared to the standard single-side read system, the MTF for the dual-side read system was slightly reduced, but a significant decrease in image noise resulted in a marked increase in DQE (+40%) in the low spatial frequency range. However, the DQE improvement for the ST-BD plate decreased with increasing spatial frequency, and, at spatial frequencies above 2.2 mm(-1), the DQE of the dual-side read system was lower than that of the single-side one.

Measurement systems in wall production applications

Tässä tutkimuksessa kehitettiin prototyyppi betonielementin dimension mittaus järjestelmästä. Tämä järjestelmä mahdollistaa kolmiulotteisen kappaleen mittauksen. Tutkimuksessa kehitettiin myös stereonäköön perustuva kappaleen mittaus. Prototyyppiä testailin ja tulokset osoittautuivat luotettaviksi. Tutkimuksessa selvitetään ja vertaillaan myös muita lähestymistapoja ja olemassa olevia järjestelmiä kappaleen kolmiuloitteiseen mittaukseen, joita Suomalaiset yhtiöt käyttävät tällä alalla.

Methods of Design and Testing of Real Time Systems

Teollusuussovelluksissa vaaditaan nykyisin yhä useammin reaaliaikaista tiedon käsittelyä. Luotettavuus on yksi tärkeimmistä reaaliaikaiseen tiedonkäsittelyyn kykenevän järjestelmän ominaisuuksista. Sen saavuttamiseksi on sekä laitteisto, että ohjelmisto testattava. Tämän työn päätavoitteena on laitteiston testaaminen ja laitteiston testattavuus, koska luotettava laitteistoalusta on perusta tulevaisuuden reaaliaikajärjestelmille. Diplomityössä esitetään digitaaliseen signaalinkäsittelyyn soveltuvan prosessorikortin suunnittelu. Prosessorikortti on tarkoitettu sähkökoneiden ennakoivaa kunnonvalvontaa varten. Uusimmat DFT (Desing for Testability) menetelmät esitellään ja niitä sovelletaan prosessorikortin sunnittelussa yhdessä vanhempien menetelmien kanssa. Kokemukset ja huomiot menetelmien soveltuvuudesta raportoidaan työn lopussa. Työn tavoitteena on kehittää osakomponentti web -pohjaiseen valvontajärjestelmään, jota on kehitetty Sähkötekniikan osastolla Lappeenrannan teknillisellä korkeakoululla.

A Prototype for a Multimodal Biometric Security system based on Face and Audio Signatures

Any automatically measurable, robust and distinctive physical characteristic or personal trait that can be used to identify an individual or verify the claimed identity of an individual, referred to as biometrics, has gained significant interest in the wake of heightened concerns about security and rapid advancements in networking, communication and mobility. Multimodal biometrics is expected to be ultra-secure and reliable, due to the presence of multiple and independent—verification clues. In this study, a multimodal biometric system utilising audio and facial signatures has been implemented and error analysis has been carried out. A total of one thousand face images and 250 sound tracks of 50 users are used for training the proposed system. To account for the attempts of the unregistered signatures data of 25 new users are tested. The short term spectral features were extracted from the sound data and Vector Quantization was done using K-means algorithm. Face images are identified based on Eigen face approach using Principal Component Analysis. The success rate of multimodal system using speech and face is higher when compared to individual unimodal recognition systems

Stringed bed suspended bioreactors (SBSBR)for in situ nitrification in penaeid and non-penaeid hatchery systems

For establishing nitrification in prawn (non-penaeid, salinity 10–15 ppt) and shrimp (penaeid, salinity 30–35 ppt) larval production systems, a stringed bed suspended bioreactor (SBSBR) was designed, fabricated, and validated. It was fabricated with 5 mm polystyrene and low density polyethylene beads as the substrata for ammonia and nitrite oxidizing bacterial consortia, respectively, with an overall surface area of 684 cm2. The reactors were activated in a prototype activator and were transported in polythene bags to the site of testing. Performance of the reactors activated with the nitrifying bacterial consortia AMONPCU-1 (ammonia oxidizers for non-penaeid culture) and NIONPCU-1 (nitrite oxidizers for non-penaeid culture) was evaluated in a Macrobrachium rosenbergii larval rearing system and those activated with AMOPCU-1 (ammonia oxidizers for penaeid culture) and NIOPCU-1 (nitrite oxidizers for penaeid culture) in a Penaeus monodon seed production system. Rapid setting up of nitrification could be observed in both the static systems which resulted in a higher relative per cent survival of larvae

Seminar: Symbol Management systems to support democracy in development of an online Symbol Dictionary

Abstract This seminar will introduce an initial year of research exploring participation in the development of a bilingual symbol dictionary. Symbols can be a communication and literacy ‘lifeline’ for those unable to communicate through speech or writing. We will discuss how an online system has been built to overcome language, cultural and literacy skill issues for a country where 86% are expatriates but the target clients are Arabic born individuals with speech and language impairments. The symbols in use at present are inappropriate and yet there is no democratic way of providing a ‘user voice’ for making choices, let alone easy mechanisms for adapting and sharing newly developed symbols across the nation or extended Arabic world. This project aims to change this situation. Having sourced a series of symbols that could be adapted to suit user’s needs, the team needed to encourage those users, their carers and therapists to vote on whether the symbols would be appropriate and work with those already in use. The first prototype was developed and piloted during the WAISfest in 2013. The second phase needs further voting on the most suitably adapted symbols for use when communicating with others. There is a requirement to have mechanisms for evaluating the outcome of the votes, where symbols fail to represent accurate meanings, have inappropriate colours, representations and actions etc. There also remains the need to collect both quantitative and qualitative data. Not easy in a climate of acceptance of the expert view, a culture where to be critical can be a problem and time is not of the essence.

Supervisory systems in waste water treatment plants: sistematise their implementation

La implantació de Sistemes de Suport a la presa de Decisions (SSD) en Estacions Depuradores d'Aigües Residuals Urbanes (EDAR) facilita l'aplicació de tècniques més eficients basades en el coneixement per a la gestió del procés, assegurant la qualitat de l'aigua de sortida tot minimitzant el cost ambiental de la seva explotació. Els sistemes basats en el coneixement es caracteritzen per la seva capacitat de treballar amb dominis molt poc estructurats, i gran part de la informació rellevant de tipus qualitatiu i/o incerta. Precisament aquests són els trets característics que es poden trobar en els sistemes biològics de depuració, i en conseqüència en una EDAR. No obstant, l'elevada complexitat dels SSD fa molt costós el seu disseny, desenvolupament i aplicació en planta real, pel que resulta determinant la generació d'un protocol que faciliti la seva exportació a EDARs de tecnologia similar. L'objectiu del present treball de Tesi és precisament el desenvolupament d'un protocol que faciliti l'exportació sistemàtica de SSD i l'aprofitament del coneixement del procés prèviament adquirit. El treball es desenvolupa en base al cas d'estudi resultant de l'exportació a l'EDAR Montornès del prototipus original de SSD implementat a l'EDAR Granollers. Aquest SSD integra dos tipus de sistemes basats en el coneixement, concretament els sistemes basats en regles (els quals són programes informàtics que emulen el raonament humà i la seva capacitat de solucionar problemes utilitzant les mateixes fonts d'informació) i els sistemes de raonament basats en casos (els quals són programes informàtics basats en el coneixement que volen solucionar les situacions anormals que pateix la planta en el moment actual mitjançant el record de l'acció efectuada en una situació passada similar). El treball està estructurat en diferents capítols, en el primer dels quals, el lector s'introdueix en el món dels sistemes de suport a la decisió i en el domini de la depuració d'aigües. Seguidament es fixen els objectius i es descriuen els materials i mètodes utilitzats. A continuació es presenta el prototipus de SSD desenvolupat per la EDAR Granollers. Una vegada el prototipus ha estat presentat es descriu el primer protocol plantejat pel mateix autor de la Tesi en el seu Treball de Recerca. A continuació es presenten els resultats obtinguts en l'aplicació pràctica del protocol per generar un nou SSD, per una planta depuradora diferent, partint del prototipus. L'aplicació pràctica del protocol permet l'evolució del mateix cap a un millor pla d'exportació. Finalment, es pot concloure que el nou protocol redueix el temps necessari per realitzar el procés d'exportació, tot i que el nombre de passos necessaris ha augmentat, la qual cosa significa que el nou protocol és més sistemàtic.

A system's model for maintenance support and decision making in building services systems

Modern buildings are designed to enhance the match between environment, spaces and the people carrying out work, so that the well-being and the performance of the occupants are all in harmony. Building services are systems that facilitate a healthy working environment within which workers productivity can be optimised in the buildings. However, the maintenance of these services is fraught with problems that may contribute to up to 50% of the total life cycle cost of the building. Maintenance support is one area which is not usually designed into the system as this is not common practice in the services industry. The other areas of shortfall for future designs are; client requirements, commissioning, facilities management data and post occupancy evaluation feedback which needs to be adequately planned to capture and document this information for use in future designs. At the University of Reading an integrated approach has been developed to assemble the multitude of aspects inherent in this field. The means records required and measured achievements for the benefit of both building owners and practitioners. This integrated approach can be represented in a Through Life Business Model (TLBM) format using the concept of Integrated Logistic Support (ILS). The prototype TLBM developed utilises the tailored tools and techniques of ILS for building services. This TLBM approach will facilitate the successful development of a databank that would be invaluable in capturing essential data (e.g. reliability of components) for enhancing future building services designs, life cycle costing and decision making by practitioners, in particular facilities managers.

The findings from a single pass deghoster prototype for terrestrial transmitted video

A deterministic prototype video deghoster is presented which is capable of calculating all the multipath channel distortion characteristics in one single pass and subsequently removing the multipath distortions, commonly termed ghosts. Within the system, a channel identification algorithm finds in isolation all the ghost components while a dedicated DSP filter subsystem is capable of removing ghosts in real time. The results from the system are presented.

Are superhumps good measures of the mass ratio for AM CVn systems?

We extend recent work that included the effect of pressure forces to derive the precession rate of eccentric accretion discs in cataclysmic variables to the case of double degenerate systems. We find that the logical scaling of the pressure force in such systems results in predictions of unrealistically high primary masses. Using the prototype AM CVn as a calibrator for the magnitude of the effect, we find that there is no scaling that applies consistently to all the systems in the class. We discuss the reasons for the lack of a superhump period to mass ratio relationship analogous to that known for SU UMa systems and suggest that this is because these secondaries do not have a single valued mass-radius relationship. We highlight the unreliability of mass-ratios derived by applying the SU UMa expression to the AM CVn binaries.

Prototype Generation from Ontology Charts

Semantic Analysis is a business analysis method designed to capture system requirements. While these requirements may be represented as text, the method also advocates the use of Ontology Charts to formally denote the system's required roles, relationships and forms of communication. Following model driven engineering techniques, Ontology Charts can be transformed to temporal Database schemas, class diagrams and component diagrams, which can then be used to produce software systems. A nice property of these transformations is that resulting system design models lend themselves to complicated extensions that do not require changes to the design models. For example, resulting databases can be extended with new types of data without the need to modify the database schema of the legacy system. Semantic Analysis is not widely used in software engineering, so there is a lack of experts in the field and no design patterns are available. This make it difficult for the analysts to pass organizational knowledge to the engineers. This study describes an implementation that is readily usable by engineers, which includes an automated technique that can produce a prototype from an Ontology Chart. The use of such tools should enable developers to make use of Semantic Analysis with minimal expertise of ontologies and MDA.

Volunteered Geographic Information For Water Management: A Prototype Architecture

Driven by Web 2.0 technology and the almost ubiquitous presence of mobile devices, Volunteered Geographic Information (VGI) is knowing an unprecedented growth. These notable technological advancements have opened fruitful perspectives also in the field of water management and protection, raising the demand for a reconsideration of policies which also takes into account the emerging trend of VGI. This research investigates the opportunity of leveraging such technology to involve citizens equipped with common mobile devices (e.g. tablets and smartphones) in a campaign of report of water-related phenomena. The work is carried out in collaboration with ADBPO - Autorità di bacino del fiume Po (Po river basin Authority), i.e. the entity responsible for the environmental planning and protection of the basin of river Po. This is the longest Italian river, spreading over eight among the twenty Italian Regions and characterized by complex environmental issues. To enrich ADBPO official database with user-generated contents, a FOSS (Free and Open Source Software) architecture was designed which allows not only user field-data collection, but also data Web publication through standard protocols. Open Data Kit suite allows users to collect georeferenced multimedia information using mobile devices equipped with location sensors (e.g. the GPS). Users can report a number of environmental emergencies, problems or simple points of interest related to the Po river basin, taking pictures of them and providing other contextual information. Field-registered data is sent to a server and stored into a PostgreSQL database with PostGIS spatial extension. GeoServer provides then data dissemination on the Web, while specific OpenLayers-based viewers were built to optimize data access on both desktop computers and mobile devices. Besides proving the suitability of FOSS in the frame of VGI, the system represents a successful prototype for the exploitation of user local, real-time information aimed at managing and protecting water resources.

Organizations redesign and building of information systems

Develop software is still a risky business. After 60 years of experience, this community is still not able to consistently build Information Systems (IS) for organizations with predictable quality, within previously agreed budget and time constraints. Although software is changeable we are still unable to cope with the amount and complexity of change that organizations demand for their IS. To improve results, developers followed two alternatives: Frameworks that increase productivity but constrain the flexibility of possible solutions; Agile ways of developing software that keep flexibility with less upfront commitments. With strict frameworks, specific hacks have to be put in place to get around the framework construction options. In time this leads to inconsistent architectures that are harder to maintain due to incomplete documentation and human resources turnover. The main goals of this work is to create a new way to develop flexible IS for organizations, using web technologies, in a faster, better and cheaper way that is more suited to handle organizational change. To do so we propose an adaptive object model that uses a new ontology for data and action with strict normalizing rules. These rules should bound the effects of changes that can be better tested and therefore corrected. Interfaces are built with templates of resources that can be reused and extended in a flexible way. The “state of the world” for each IS is determined by all production and coordination acts that agents performed over time, even those performed by external systems. When bugs are found during maintenance, their past cascading effects can be checked through simulation, re-running the log of transaction acts over time and checking results with previous records. This work implements a prototype with part of the proposed system in order to have a preliminary assessment its feasibility and limitations.

A novel HPF voltage source rectifier for variable speed refrigeration systems

A novel single-phase voltage source rectifier capable to achieve High-Power-Factor (HPF) for variable speed refrigeration system application, is proposed in this paper. The proposed system is composed by a single-phase high-power-factor boost rectifier, with two cells in interleave connection, operating in critical conduction mode, and employing a soft-switching technique, controlled by a Field Programmable Gate Array (FPGA), associated with a conventional three-phase IGBT bridge inverter (VSI - Voltage Source Inverter), controlled by a Digital Signal Processor (DSP). The soft-switching technique for the input stage is based on zero-current-switching (ZCS) cells. The rectifier's features include the reduction in the input current ripple, the reduction in the output voltage ripple, the use of low stress devices, low volume for the EMI input filter, high input power factor (PF), and low total harmonic distortion (THD) in the input current, in compliance with the EEC61000-3-2 standards. The digital controller for the output stage has been developed using a conventional voltage-frequency control (scalar V/f control), and a simplified stator oriented Vector control, in order to verify the feasibility and performance of the proposed digital controls for continuous temperature control applied at a refrigerator prototype.

Development of a prototype for measuring plantar forces

Studies on the distribution of plantar pressure between the sole of the foot and the ground were developed before the 19th century. Currently, the most often employed plantar pressure measurement systems are Pedar® and FScan®, which have restrictions such as operational difficulty and high cost. In the present study, a device was constructed from two pressure plates capable of measuring plantar forces in discreet areas of the feet at a low cost, using strain-gages attached to sixteen strategic points of the mechanical elements. Sixteen prismatic beams were soldered to each frame, for which the free extremity of each beam represented a specific point of the foot. Two strain gauges were attached to each beam - one near the upper fixed extremity and the other near the lower fixed extremity. Using a Wheatstone bridge electric circuit, the gauges were used to measure the force acting on the extremity of the beam. Precision and accuracy of the prototype was about 10%. In some measurements, accuracy was 2%. The low precision and accuracy were mainly due to the restrictions of the available equipment, which only permitted four measurements at a time. Thus, it was necessary for participants to stand on the plates four separate times, which signified possible changes in the position of the feet on the pressure plates. Despite some limitations, the aim was achieved. The prototype has been used in some studies and represents a contribution to biomechanics, demonstrating the viability of using strain gauges.