Building intuition of iron evolution during solar cell processing through analysis of different process models

An important aspect of Process Simulators for photovoltaics is prediction of defect evolution during device fabrication. Over the last twenty years, these tools have accelerated process optimization, and several Process Simulators for iron, a ubiquitous and deleterious impurity in silicon, have been developed. The diversity of these tools can make it difficult to build intuition about the physics governing iron behavior during processing. Thus, in one unified software environment and using self-consistent terminology, we combine and describe three of these Simulators. We vary structural defect distribution and iron precipitation equations to create eight distinct Models, which we then use to simulate different stages of processing. We find that the structural defect distribution influences the final interstitial iron concentration ([Fe-i]) more strongly than the iron precipitation equations. We identify two regimes of iron behavior: (1) diffusivity-limited, in which iron evolution is kinetically limited and bulk [Fe-i] predictions can vary by an order of magnitude or more, and (2) solubility-limited, in which iron evolution is near thermodynamic equilibrium and the Models yield similar results. This rigorous analysis provides new intuition that can inform Process Simulation, material, and process development, and it enables scientists and engineers to choose an appropriate level of Model complexity based on wafer type and quality, processing conditions, and available computation time.

Optimization of Chemical Processes Using Surrogate Models Based on a Kriging Interpolation

Superstructure approaches are the solution to the difficult problem which involves the rigorous economic design of a distillation column. These methods require complex initialization procedures and they are hard to solve. For this reason, these methods have not been extensively used. In this work, we present a methodology for the rigorous optimization of chemical processes implemented on a commercial simulator using surrogate models based on a kriging interpolation. Several examples were studied, but in this paper, we perform the optimization of a superstructure for a non-sharp separation to show the efficiency and effectiveness of the method. Noteworthy that it is possible to get surrogate models accurate enough with up to seven degrees of freedom.

Large scale optimization of a sour water stripping plant using surrogate models

In this work, we propose a new methodology for the large scale optimization and process integration of complex chemical processes that have been simulated using modular chemical process simulators. Units with significant numerical noise or large CPU times are substituted by surrogate models based on Kriging interpolation. Using a degree of freedom analysis, some of those units can be aggregated into a single unit to reduce the complexity of the resulting model. As a result, we solve a hybrid simulation-optimization model formed by units in the original flowsheet, Kriging models, and explicit equations. We present a case study of the optimization of a sour water stripping plant in which we simultaneously consider economics, heat integration and environmental impact using the ReCiPe indicator, which incorporates the recent advances made in Life Cycle Assessment (LCA). The optimization strategy guarantees the convergence to a local optimum inside the tolerance of the numerical noise.

Expansion, harvest and cryopreservation of human mesenchymal stem cells in a serum-free microcarrier process

Human mesenchymal stem cell (hMSC) therapies are currently progressing through clinical development, driving the need for consistent, and cost effective manufacturing processes to meet the lot-sizes required for commercial production. The use of animal-derived serum is common in hMSC culture but has many drawbacks such as limited supply, lot-to-lot variability, increased regulatory burden, possibility of pathogen transmission, and reduced scope for process optimization. These constraints may impact the development of a consistent large-scale process and therefore must be addressed. The aim of this work was therefore to run a pilot study in the systematic development of serum-free hMSC manufacturing process. Human bone-marrow derived hMSCs were expanded on fibronectin-coated, non-porous plastic microcarriers in 100mL stirred spinner flasks at a density of 3×10⁵cells.mL^-1 in serum-free medium. The hMSCs were successfully harvested by our recently-developed technique using animal-free enzymatic cell detachment accompanied by agitation followed by filtration to separate the hMSCs from microcarriers, with a post-harvest viability of 99.63±0.03%. The hMSCs were found to be in accordance with the ISCT characterization criteria and maintained hMSC outgrowth and colony-forming potential. The hMSCs were held in suspension post-harvest to simulate a typical pooling time for a scaled expansion process and cryopreserved in a serum-free vehicle solution using a controlled-rate freezing process. Post-thaw viability was 75.8±1.4% with a similar 3h attachment efficiency also observed, indicating successful hMSC recovery, and attachment. This approach therefore demonstrates that once an hMSC line and appropriate medium have been selected for production, multiple unit operations can be integrated to generate an animal component-free hMSC production process from expansion through to cryopreservation.

The implementation of mini-enterprise business process management.

Obviously, it is important for the mini-enterprise to acknowledgement that how to win the customers and markets, because the products must be continuously evolved so as to satisfy the customer, otherwise it will be disused by the market, that is a major problems for nowadays mini-enterprise business process management. In fact, in order to satisfy the customers, the overall business processes for mini-enterprises are mostly based on integrated business process, optimization on the integrated business process is vital for a successful min-enterprise. this paper explores how to optimize the business process of mini-enterprises based on the general principle of enterprise business process management and the main feature of the mini-enterprise, so as to instruct the mini-enterprise to control, enhance and optimize the business process in order to meet the inner requirements from the development of the enterprise and adapt itself with the continuous changes of the outside environment, most vitally it can enhance the process or re-design the process so as to meet business demands from customers.

Additive Manufacturing by LPBF and WAAM of metals: correlation between production process, microstructure and mechanical properties

In the most recent years, Additive Manufacturing (AM) has drawn the attention of both academic research and industry, as it might deeply change and improve several industrial sectors. From the material point of view, AM results in a peculiar microstructure that strictly depends on the conditions of the additive process and directly affects mechanical properties. The present PhD research project aimed at investigating the process-microstructure-properties relationship of additively manufactured metal components. Two technologies belonging to the AM family were considered: Laser-based Powder Bed Fusion (LPBF) and Wire-and-Arc Additive Manufacturing (WAAM). The experimental activity was carried out on different metals of industrial interest: a CoCrMo biomedical alloy and an AlSi7Mg0.6 alloy processed by LPBF, an AlMg4.5Mn alloy and an AISI 304L austenitic stainless steel processed by WAAM. In case of LPBF, great attention was paid to the influence that feedstock material and process parameters exert on hardness, morphological and microstructural features of the produced samples. The analyses, targeted at minimizing microstructural defects, lead to process optimization. For heat-treatable LPBF alloys, innovative post-process heat treatments, tailored on the peculiar hierarchical microstructure induced by LPBF, were developed and deeply investigated. Main mechanical properties of as-built and heat-treated alloys were assessed and they were well-correlated to the specific LPBF microstructure. Results showed that, if properly optimized, samples exhibit a good trade-off between strength and ductility yet in the as-built condition. However, tailored heat treatments succeeded in improving the overall performance of the LPBF alloys. Characterization of WAAM alloys, instead, evidenced the microstructural and mechanical anisotropy typical of AM metals. Experiments revealed also an outstanding anisotropy in the elastic modulus of the austenitic stainless-steel that, along with other mechanical properties, was explained on the basis of microstructural analyses.

Optimizing model predictive control of an industrial distillation column

The main scope of this work is the implementation of an MPC that integrates the control and the economic optimization of the system. The two problems are solved simultaneously through the modification of the control cost function that includes an additional term related to the economic objective. The optimizing MPC is based on a quadratic program (QP) as the conventional MPC and can be solved with the available QP solvers. The method was implemented in an industrial distillation system, and the results show that the approach is efficient and can be used, in several practical cases. (C) 2011 Elsevier Ltd. All rights reserved.

Optimal synthesis of Fenton reactor networks for phenol degradation

There is an increasing need to treat effluents contaminated with phenol with advanced oxidation processes (AOPs) to minimize their impact on the environment as well as on bacteriological populations of other wastewater treatment systems. One of the most promising AOPs is the Fenton process that relies on the Fenton reaction. Nevertheless, there are no systematic studies on Fenton reactor networks. The objective of this paper is to develop a strategy for the optimal synthesis of Fenton reactor networks. The strategy is based on a superstructure optimization approach that is represented as a mixed integer non-linear programming (MINLP) model. Network superstructures with multiple Fenton reactors are optimized with the objective of minimizing the sum of capital, operation and depreciation costs of the effluent treatment system. The optimal solutions obtained provide the reactor volumes and network configuration, as well as the quantities of the reactants used in the Fenton process. Examples based on a case study show that multi-reactor networks yield decrease of up to 45% in overall costs for the treatment plant. (C) 2010 The Institution of Chemical Engineers. Published by Elsevier B.V. All rights reserved.

Extractive Fermentation of Clavulanic Acid by Streptomyces DAUFPE 3060 Using Aqueous Two-Phase System

The influence of four variables, specifically PEG molar mass (400, 1,000, and 8,000 g/mol), concentrations of PEG and phosphate salts (15, 20, and 25% for both), and agitation intensity (110, 150, and 200 rpm), on clavulanic acid (CA) extraction by extractive fermentation with PEG/phosphate salts aqueous two-phase system was investigated in shaken flasks using a 2(4-1)-fractional factorial design. After selection of the two most significant variables (agitation intensity and PEG molar mass), an optimization study conducted according to a 2(2)-central composite design revealed that 25% PEG 8,000 g/mol and phosphate salts at 240 rpm (run 6) were the best conditions for the extractive fermentation, leading to the best results in terms of partition coefficient (k = 8.2), yield of CA in the PEG-rich phase (eta(T) = 93%) and productivity (P = 5.3 mg/Lh). As a first attempt to make a scale-up of these results, the effectiveness of the extractive fermentation was then checked in a bench-scale bioreactor under conditions as close as possible to the optimum ones determined in flasks. The highest CA concentration obtained in the PEG-rich phase (691 mg/L) was 30% higher than in flasks, thus demonstrating the potential of such a new process, integrating the production and extraction steps, as a promising, low-cost tool to obtain high yields of this and similar products. (C) 2010 American Institute of Chemical Engineers Biotechnol. Prog., 27: 95-103, 2011

Anthocyanin synthesis, growth and nutrient uptake in suspension cultures of strawberry cells

Strawberry (Fragaria ananassa cv. Shikinari) cell suspension cultures carried out in shake flasks for 18 d were closely examined for cell growth, anthocyanin synthesis and the development of pigmented cells in relation to the uptake of carbohydrate, extracellular PO4, NO3, NH4, and calcium. Cell viability, extracellular anthocyanin content, pH and electrical conductivity of the broth were also monitored. The specific growth rate of strawberry cells at exponential phase was 0.27 and 0.28 d(-1) based on fresh and dry weight, respectively. Anthocyanin synthesis was observed to increase continuously to a maximum value of 0.86 mg/g fresh cell weight (FCW) at day 6, and was partially growth-associated. Anthocyanin synthesis was linearly related to the increase in pigmented cell ratio, which increased with time and reached a maximum value of ca. 70% at day 6 due to reduction in cell viability and depletion of substrate. Total carbohydrate uptake was closely associated with increase in cell growth, and glucose was utilized in preference to fructose. Nitrate and ammonia were consumed until 9 d of culture, but phosphate was completely absorbed within 4 d. Calcium was assimilated throughout the growth cycle. After 9 d, cell lysis was observed which resulted in the leakage of intracellular substances and a concomitant pH rise. Anthocyanin was never detected in the broth although the broth became darkly pigmented during the lysis period. This suggests that anthocyanin was synthesized only by viable pigmented cells, and degraded rapidly upon cell death and lysis. Based on the results of kinetic analysis, a model was developed by incorporating governing equations for the ratio of pigmented cells into a Bailey and Nicholson's model. This was verified by comparison with the experimental data. The results suggest Bat the model satisfactorily describes the strawberry cell culture process, and may thus be used for process optimization.

Modelling cement grinding circuits

Modelling and simulation studies were carried out at 26 cement clinker grinding circuits including tube mills, air separators and high pressure grinding rolls in 8 plants. The results reported earlier have shown that tube mills can be modelled as several mills in series, and the internal partition in tube mills can be modelled as a screen which must retain coarse particles in the first compartment but not impede the flow of drying air. In this work the modelling has been extended to show that the Tromp curve which describes separator (classifier) performance can be modelled in terms of d(50)(corr), by-pass, the fish hook, and the sharpness of the curve. Also the high pressure grinding rolls model developed at the Julius Kruttschnitt Mineral Research Centre gives satisfactory predictions using a breakage function derived from impact and compressed bed tests. Simulation studies of a full plant incorporating a tube mill, HPGR and separators showed that the models could successfully predict the performance of the another mill working under different conditions. The simulation capability can therefore be used for process optimization and design. (C) 2001 Elsevier Science Ltd. All rights reserved.

Level monitoring system for waste oil containers: an EPS@ISEP project

Waste oil recycling companies play a very important role in our society. Competition among companies is tough and process optimization is essential for survival. By equipping oil containers with a level monitoring system that periodically reports the level and alerts when it reaches the preset threshold, the oil recycling companies are able to streamline the oil collection process and, thus, reduce the operation costs while maintaining the quality of service. This paper describes the development of this level monitoring system by a team of four students from different engineering backgrounds and nationalities. The team conducted a study of the state of the art, draw marketing and sustainable development plans and, finally, designed and implemented a prototype that continuously measures the container content level and sends an alert message as soon as it reaches the preset capacity.

Optimização de uma máquina de pultrusão

Este trabalho teve como principal objectivo optimizar um equipamento de produção de perfis pultrudidos já existente na empresa ALTO – PERFIS PULTRUDIDOS, Lda. O trabalho surgiu na sequência de um Projecto financiado pelo Programa QREN – Quadro de Referência Estratégico Nacional, determinadas debilidades identificadas no processo de pultrusão, principalmente ao nível da eficiência térmica na fieira e de alguma falta de produtividade devida às diversas operações necessárias à mudança da fieira consoante o tipo de perfil a produzir. Após um levantamento prévio da situação e uma adequada segmentação da máquina nas diferentes partes que a constituem e que contribuem activamente para o processo de produção dos perfis, foi elaborada uma lista de prioridades e foram sendo procuradas as soluções mais adequadas para cada caso, sempre com a participação activa da empresa, com vista à sua implementação final. A metodologia adoptada passou sempre por uma reunião inicial com os representantes da empresa e com os orientadores, efectuando-se a tradicional “tempestade de ideias”. Depois da correspondente maturação, desenvolvimento e aprovação prévia, por parte da empresa, as ideias foram desenvolvidas e até implementadas na sua maioria. O saldo poderá considerar-se extremamente positivo, tanto para a empresa que, ao implementar as soluções, as validou e ganhou competitividade, como para as pessoas envolvidas neste projecto, através da enorme aprendizagem adquirida.

Otimização Energética na Produção de Biodiesel

Enquadrado num contexto cada vez mais marcado pela necessidade imperiosa de adoção e desenvolvimento de práticas ambientais e energeticamente sustentáveis, este trabalho visa contribuir para a caracterização e otimização do consumo de energia na produção de biodiesel. O biodiesel pode ser encarado como uma boa resposta aos graves problemas que os combustíveis fósseis estão a provocar nas sociedades modernas, pois é uma fonte de energia biodegradável, não-tóxica e sintetizada a partir de várias matérias-primas. Porém, o elevado custo de produção, como consequência do elevado preço das matérias-primas, constitui o maior problema para a sua implementação e comercialização a grande escala. A produção de biodiesel é, em sua quase totalidade, conduzida por via de reação de transesterificação, usando óleo vegetal e álcool como matérias-primas. O objetivo geral deste trabalho é otimizar energeticamente um processo de produção de biodiesel, via catálise homogênea alcalina (BCHA). Para alcançar esse objetivo, um fluxograma típico de produção foi construído e analisado, tanto do ponto de vista energético como econômico. Posteriormente oportunidades de otimização do processo foram identificadas, no sentido de reduzir o consumo de utilidades, impacto ambiental e aumentar a rentabilidade econômica. A construção do processo, a caracterização da alimentação, os critérios de operacionalidade, a obtenção de resultados e demais fatores foram efetuados com auxílio de um software de simulação Aspen Plus versão 20.0 criado pela Aspen Technology products. Os resultados do trabalho revelaram que o processo BCHA produz uma corrente com 99,9 % em biodiesel, obedecendo às normas internacionais em vigor. Na parte energética, o processo BCHA base necessitou de 21.405,1 kW em utilidades quentes e 14.886,3 kW em utilidades frias. A integração energética do processo BCHA, segundo a metodologia pinch, permitiu uma redução das necessidades quentes para 10.752,3 kW (redução de 50 %) e frias para 4.233,5 kW (redução de 72 %). A temperatura no ponto de estrangulamento (PE) foi de 157,7 ºC nas correntes quentes e 147,7 ºC nas correntes frias. Em termos econômicos, o custo total é reduzido em 35% com a integração energética proposta. Essa diminuição, deve-se sobretudo à redução do custo operacional, onde as necessidades de vapor de muita alta pressão (VMAP), vapor de alta pressão (VAP) e água de resfriamento (AR) apresentaram quebras de 2 %, 92 % e 71 %, respectivamente. Como conclusão final, salienta-se que a integração do processo BCHA estudado é energética e economicamente viável.

Integração Energética da Unidade de Pré-destilação U-0100 da Fábrica de Aromáticos

A presente dissertação foi realizada no âmbito do Mestrado em Engenharia Química no ramo de Otimização Energética na Indústria Química, do Instituto Superior de Engenharia do Porto. O estudo energético foi desenvolvido na empresa Petrogal, S.A, na Refinaria de Matosinhos, avaliando a possível racionalização energética do processo existente na Fábrica de Aromáticos. Os objetivos propostos basearam-se na realização de uma integração energética à unidade de pré-destilação, denominada por U-0100, que se encontra instalada na Fábrica de Aromáticos. Pretende-se, de uma forma geral, o reaproveitamento máximo da energia do processo, diminuindo o recurso a utilidades externas. Para tal recorreu-se à metodologia da análise do ponto de estrangulamento, designada por tecnologia Pinch. Numa primeira fase da otimização foi necessário conhecer todo o processo em causa e os conceitos associados à tecnologia aplicada. Após contactar com o processo procedeu-se ao levantamento energético do mesmo, referente ao ano 2013. Nesta etapa foram recolhidos todos os dados considerados relevantes para a quantificação energética das correntes e das utilidades empregues. Depois da recolha efetuou-se a integração energética estabelecendo um ∆Tmin ótimo para o processo de 5°C, após uma prévia análise da influência deste parâmetro sobre os consumos. Constatou-se que atualmente o processo de separação opera com uma taxa de recuperação energética de 16,8% da energia total, sendo a restante energia introduzida por utilidades externas. Com a análise do ponto de estrangulamento concluiu-se que a unidade de pré - destilação U-0100 se encontra integrada energeticamente, não sendo essencial proceder a qualquer modificação à mesma. No entanto sugere-se como trabalho futuro um estudo técnico e económico da implementação de um pré-aquecedor de ar, necessário ao processo de combustão que se dá na fornalha H-0101. Isto tendo em vista o reaproveitamento máximo da corrente, gases de combustão, que é desperdiçada para o meio ambiente.