Delivery of the antibiotic gentamicin sulphate from precipitation cast matrices of polycaprolactone

Microporous, poly(ε-caprolactone) (PCL) matrices were loaded with the aminoglycoside antibiotic, gentamicin sulphate (GS) using the precipitation casting technique by suspension of powder in the PCL solution prior to casting. Improvements in drug loading from 1.8% to 6.7% w/w and distribution in the matrices were obtained by pre-cooling the suspension to 4°C. Gradual release of approximately 80% of the GS content occurred over 11 weeks in PBS at 37°C and low amounts of antibiotic were measured up to 20 weeks. The kinetics of release could be described effectively by the Higuchi model with the diffusion rate constant (D) increasing from of 1.7 to 5.1 μg/mg matrix/day0.5 as the drug loading increased from 1.4% to 8.3% w/w. GS-loaded PCL matrices retained anti-bacterial activity after immersion in PBS at 37°C over 14 days as demonstrated by inhibition of growth of S. epidermidis in culture. These findings recommend further investigation of precipitation-cast PCL matrices for delivery of hydrophilic molecules such as anti-bacterial agents from implanted, inserted or topical devices. © 2005 Elsevier B.V. All rights reserved.

Composite cell support membranes based on collagen and polycaprolactone for tissue engineering of skin

The preparation and characterisation of collagen:PCL composites for manufacture of tissue engineered skin substitutes and models are reported. Films having collagen:PCL (w/w) ratios of 1:4, 1:8 and 1:20 were prepared by impregnation of lyophilised collagen mats by PCL solutions followed by solvent evaporation. In vitro assays of collagen release and residual collagen content revealed an expected inverse relationship between the collagen release rate and the content of synthetic polymer in the composite that may be exploited for controlled presentation and release of biopharmaceuticals such as growth factors. DSC analysis revealed the characteristic melting point of PCL at around 60°C and a tendency for the collagen component, at high loading, to impede crystallinity development within the PCL phase. The preparation of fibroblast/composite constructs was investigated using cell culture as a first stage in mimicking the dermal/epidermal structure of skin. Fibroblasts were found to attach and proliferate on all the composites investigated reaching a maximum of 2×105/cm2 on 1:20 collagen:PCL materials at day 8 with cell numbers declining thereafter. Keratinocyte growth rates were similar on all types of collagen:PCL materials investigated reaching a maximum of 6.6×104/cm2 at day 6. The results revealed that composite films of collagen and PCL are favourable substrates for growth of fibroblasts and keratinocytes and may find utility for skin repair. © 2003 Elsevier Ltd. All rights reserved.

Gravity spun polycaprolactone fibres for soft tissue engineering:interaction with fibroblasts and myoblasts in cell culture

Poly(ε-caprolactone) (PCL) fibres were produced by wet spinning from solutions in acetone under low shear (gravity flow) conditions. As-spun PCL fibres exhibited a mean strength and stiffness of 7.9 MPa and 0.1 GPa, respectively and a rough, porous surface morphology. Cold drawing to an extension of 500% resulted in increases in fibre strength (43 MPa) and stiffness (0.3 GPa) and development of an oriented, fibrillar surface texture. The proliferation rate of Swiss 3T3 mouse fibroblasts and C2C12 mouse myoblasts on as-spun, 500% cold-drawn and gelatin-modified PCL fibres was determined in cell culture to provide a basic measure of the biocompatibility of the fibres. Proliferation of both cell types was consistently higher on gelatin-coated fibres relative to as-spun fibres at time points below 7 days. Fibroblast growth rates on cold-drawn PCL fibres exceeded those on as-spun fibres but myoblast proliferation was similar on both substrates. After 1 day in culture, both cell types had spread and coalesced on the fibres to form a cell layer, which conformed closely to the underlying topography. The high fibre compliance combined with a potential for modifying the fibre surface chemistry with cell adhesion molecules and the surface architecture by cold drawing to enhance proliferation of fibroblasts and myoblasts, recommends further investigation of gravity-spun PCL fibres for 3-D scaffold production in soft tissue engineering. © 2005 Elsevier Ltd. All rights reserved.

PHBHV/PCL microspheres as biodegradable drug delivery systems (DDS) for photodynamic therapy (PDT)

Unloaded microspheres were prepared from polyhydroxybutyrate-co-valerate (PHBHV) and poly(epsilon-caprolactone) (PCL) polymers using the emulsification-solvent evaporation method (EE). The study was conducted to determine the ideal polymeric composition and ideal molecular weight for the microspheres preparation to be used as a Drug Delivery System (DDS) for cancer therapy. In this work, NzPC, a new photosensitizer, has been investigated when incorporated into microspheres of PHBHV/PCL evaluating its application for Photodynamic Therapy (PDT) of neoplastic tissue. The biodegradation studies were conducted to analyze the effects of the incorporation of the NzPC and also to determine the release profiles in vitro condition. We also evaluated the dark toxicity and the photobiological effect of the PHBHV-PCL microspheres in cutaneous melanoma cell line (B-16-A1) used as a biological neoplastic medium.

Fatigue Prediction on Fibrin Poly-ε-caprolactone Macroporous Scaffolds

Tissue engineering applications rely on scaffolds that during its service life, either for in-vivo or in vitro applications, are under mechanical solicitations. The variation of the mechanical condition of the scaffold is strongly relevant for cell culture and has been scarcely addressed. Fatigue life cycle of poly-ε-caprolactone, PCL, scaffolds with and without fibrin as filler of the pore structure were characterized both dry and immersed in liquid water. It is observed that the there is a strong increase from 100 to 500 in the number of loading cycles before collapse in the samples tested in immersed conditions due to the more uniform stress distributions within the samples, the fibrin loading playing a minor role in the mechanical performance of the scaffolds

Construção e caracterização de um colector rotatório para produção de nanofibras alinhadas de PCL

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Biomédica

Biodispositivos electrónicos implantáveis e biodegradáveis: nano/microfibras de poli (ε-caprolactona) (PCL)

Dissertação para obtenção do Grau de Mestre em Engenharia Biomédica

Produção de fibras de policaprolactona (PCL) por fiação centrífuga

Dissertação para obtenção do Grau de Mestre em Engenharia Biomédica

Artificial thymus: a tissue engineering strategy

The thymus is the central organ responsible for the generation of T lymphocytes (1). Various diseases cause the thymus to produce in- sufficient T cells, which can lead to immune-suppression (2). Since T cells are essential for the protection against pathogens, it is crucial to promote de novo differentiation of T cells on diseased individuals. The available clinical solutions are: 1) one protocol involving the transplant of thymic stroma from unrelated children only applicable for athymic children (3); 2) for patients with severe peripheral T cell depletion and reduced thymic activity, the administration of stimu- lating molecules stimulating the activity of the endogenous thymus (4). A scaffold (CellFoam) was suggested to support thymus regen- eration in vivo (5), although this research was discontinued. Herein, we propose an innovative strategy to generate a bioartificial thymus. We use a polycaprolactone nanofiber mesh (PCL-NFM) seeded and cultured with human thymic epithelial cells (hTECs). The cells were obtained from infant thymus collected during pediatric cardio-tho- racic surgeries. We report new data on the isolation and characterization of those cells and their interaction with PCL-NFM, by expanding hTECs into relevant numbers and by optimizing cell seeding methods.

Mechanical fatigue performance of PCL-chondroprogenitor constructs after cell culture under bioreactor mechanical stimulus

In tissue engineering of cartilage, polymeric scaffolds are implanted in the damaged tissue and subjected to repeated compression loading cycles. The possibility of failure due to mechanical fatigue has not been properly addressed in these scaffolds. Nevertheless, the macroporous scaffold is susceptible to failure after repeated loading-unloading cycles. This is related to inherent discontinuities in the material due to the micropore structure of the macro-pore walls that act as stress concentration points. In this work, chondrogenic precursor cells have been seeded in Poly-ε-caprolactone (PCL) scaffolds with fibrin and some were submitted to free swelling culture and others to cyclic loading in a bioreactor. After cell culture, all the samples were analyzed for fatigue behavior under repeated loading-unloading cycles. Moreover, some components of the extracellular matrix (ECM) were identified. No differences were observed between samples undergoing free swelling or bioreactor loading conditions, neither respect to matrix components nor to mechanical performance to fatigue. The ECM did not achieve the desired preponderance of collagen type II over collagen type I which is considered the main characteristic of hyaline cartilage ECM. However, prediction in PCL with ECM constructs was possible up to 600 cycles, an enhanced performance when compared to previous works. PCL after cell culture presents an improved fatigue resistance, despite the fact that the measured elastic modulus at the first cycle was similar to PCL with poly(vinyl alcohol) samples. This finding suggests that fatigue analysis in tissue engineering constructs can provide additional information missed with traditional mechanical measurements.

Regulation of human mesenchymal stem cell osteogenesis by specific surface density of fibronectin: a gradient study

 The success of synthetic bone implants requires good interface between the material and the host tissue. To study the biological relevance of fi bronectin (FN) density on the osteogenic commitment of human bone marrow mesenchymal stem cells (hBMMSCs), human FN was adsorbed in a linear density gradient on the surface of PCL. The evolution of the osteogenic markers alkaline phosphatase and collagen 1 alpha 1 was monitored by immunohistochemistry, and the cytoskeletal organization and the cell-derived FN were assessed. The functional analysis of the gradient revealed that the lower FN-density elicited stronger osteogenic expression and higher cytoskeleton spreading, hallmarks of the stem cell commitment to the osteoblastic lineage. The identifi cation of the optimal FN density regime for the osteogenic commitment of hBM-MSCs presents a simple and versatile strategy to signifi cantly enhance the surface properties of polycaprolactone as a paradigm for other synthetic polymers intended for bone-related applications.

Eficàcia predictiva de l’HCR-20 i del PCL:SV en contexts institucionals

L’estudi es dirigeix a avaluar la capacitat predictiva sobre la violència dels instruments de judici clínic estructurat, amb una metodologia que aporti resultats comparables a estudis de l’àmbit internacional. La investigació es va portar a terme en un hospital civil de salut mental i la mostra està composta per 114 pacients de les unitats de crònics i subaguts. A l’avaluació inicial, l’HCR-20, el PCL:SV i el Protocol 7 van ser els instruments utilitzats per a la recollida d’informació de les variables predictors. La variable depenent o resultat va ser registrada prospectivament per part de l’equip d’infermeria amb un instrument observacional de fàcil ús, el MOAS. Mitjançant índexs de correlació, càlcul de riscos relatius, i anàlisis de regressió logística i corbes ROC va ser possible conèixer que l’HCR-20 i el PCL-SV són mesures vàlides per a la predicció de la violència intrahospitalària en el curt i mig termini en una mostra espanyola de persones amb malaltia mental severa. L’HCR-20 i particularment els ítems clínics van ser els millors predictors de la violència física envers a persones i objectes. Tant la puntuació numèrica de l’HCR-20 com el judici clínic estructurat van demostrar una precisió predictiva alta i comparable a l'obtinguda amb la versió original de l'instrument. El PCL:SV va arribar una precisió predictiva moderada que va anar disminuint al llarg del seguiment. Altres factors de risc com les agressions o la ira prèvies a l’avaluació també van augmentar significativament el risc de violència durant l’any de seguiment.

Micropartículas de p(hbhv) e de blendas de p(hbhv):pcl contendo dexametasona ou acetato de dexametasona como modelos de fármacos : caracterização físico-química e perfis de liberação in vitro

Tendo em vista o controle da porosidade da matriz polimérica de micropartículas constituídas por blendas de poli(hidroxibutirato-co-hidroxivalerato) [P(HBHV)] e de poli- ε-caprolactona (PCL), o presente trabalho objetivou verificar a possibilidade de controle da liberação de fármacos associados a esses sistemas. Foram preparadas micropartículas constituídas de blendas de P(HBHV):PCL nas proporções de 100:0, 90:10 e 80:20 (m/m) pelo método de emulsificação/evaporação de solvente, variandose o volume de fase orgânica. Os modelos de fármacos utilizados foram a dexametasona e o acetato de dexametasona. As micropartículas obtidas apresentaram rendimento e eficiência de encapsulação satisfatória, entretanto, através de análises por microscopia óptica e microscopia eletrônica de varredura foi evidenciada a ocorrência de cristais de fármaco não encapsulado. Os diâmetros de partícula permaneceram em torno de 100 a 200 μm e variaram em função do volume de fase orgânica. A área superficial foi afetada pelo percentual de PCL na blenda e pela presença de cristais do fármaco nas formulações. A análise térmica das amostras demonstrou que o processo de obtenção alterou a estrutura cristalina do P(HBHV) e que a encapsulação dos fármacos levou à variação da sua temperatura de transição vítrea e cristalinidade. Os perfis de dissolução da dexametasona a partir das micropartículas apresentaram ajustes adequados ao modelo monoexponencial e foram semelhantes aos perfis apresentados pelo fármaco não encapsulado. Nas formulações contendo acetato de dexametasona houve liberação sustentada do fármaco por até 250 horas quando associado aos sistemas e a modelagem matemática indicou ajuste dos perfis ao modelo biexponencial. Evidenciou-se um aumento nos valores das constantes de liberação dos fármacos conforme o acréscimo do conteúdo de PCL na blenda.

Biodegradation of blend films in soil and soil with chorume. I. PVC/PCL

Blends of synthetic and biodegradable polymers can be important in attaining material plastic degradation in the environment. Biodegradation using soil and chorume (liquid waste from landfill) microorganisms is a promising area these days. This paper intends to study the PVC/PCL blend degradation in soil using aerobic biodegradation (Bartha respirometer). The morphology and structural changes of the blends were studied by FTIR, scanning electron microscopy, differential scanning calorimetry and contact angle measurements. Blend films prepared by the casting of dichloroethane solutions were buried in a Bartha respirometer containing soil and soil plus chorume and kept there for 120 days. During this time CO2 evolution was measured from time to time. The results showed that PCL films degrade faster than PVC/PCL and PVC films.

Influência da geometria e umidade de colunas de solo na biodegradação de filmes de PCL

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)