Effect of plant growth regulators in the rooting of Pinus cuttings

O trabalho avaliou o enraizamento de estacas de Pinus caribaea var. hondurensis Morelet sob a ação de diferentes níveis de reguladores vegetais. As estacas foram feitas de brotações de 4 a 6cm de comprimento de mudas de P. caribaea var. hondurensis Morelet com corte bisel na base sendo as acículas basais eliminadas. A base das estacas foram submetidas aos tratamentos por 2 segundos com os seguintes tratamentos: 1- NAA 2000mg L-1; 2- NAA 4000mg L-1; 3- NAA 6000mg L-1; 4- NAA 2000mg L-1 + PBZ 100mg L-1; 5- NAA 4000mg L-1 + PBZ; 6- NAA 6000mg L-1 + PBZ; 7- IBA 2000mg L-1; 8- IBA 4000mg L-1; 9- IBA 6000mg L-1; 10-IBA 2000mg L-1 + PBZ; 11- IBA 4000mg L-1 + PBZ; 12- IBA 6000mg L-1 + PBZ e testemunha. Após os tratamentos as estacas foram plantadas em tubetes contendo 50% de palha de arroz carbonizada e 50% de vermiculita. As avaliações realizadas aos 60 dias após o plantio mostraram que estacas de P. caribaea tratadas com IBA levaram a maior porcentagem de estacas enraizadas que aquelas tratadas com NAA, sendo o mais efetivo, IBA a 4000mg L-1 em conjunto com 100mg L-1 de paclobutrazol.

Uso de biossólidos como substrato para produção de mudas de pinus e eucalipto

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Avaliação da qualidade da madeira de cinco espécies de Pinus destinadas à produção de celulose

Pós-graduação em Ciência Florestal - FCA

Offsetting greenhouse gas emissions through biological carbon sequestration in North Eastern Australia

The Kyoto Protocol recognises trees as a sink of carbon and a valid means to offset greenhouse gas emissions and meet internationally agreed emissions targets. This study details biological carbon sequestration rates for common plantation species Araucaria cunninghamii (hoop pine), Eucalyptus cloeziana, Eucalyptus argophloia, Pinus elliottii and Pinus caribaea var hondurensis and individual land areas required in north-eastern Australia to offset greenhouse gas emissions of 1000tCO 2e. The 3PG simulation model was used to predict above and below-ground estimates of biomass carbon for a range of soil productivity conditions for six representative locations in agricultural regions of north-eastern Australia. The total area required to offset 1000tCO 2e ranges from 1ha of E. cloeziana under high productivity conditions in coastal North Queensland to 45ha of hoop pine in low productivity conditions of inland Central Queensland. These areas must remain planted for a minimum of 30years to meet the offset of 1000tCO 2e.

Long-term impacts of harvest residue management on nutrition, growth and productivity of an exotic pine plantation of sub-tropical Australia

Residue retention is an important issue in evaluating the sustainability of production forestry. However, its long-term impacts have not been studied extensively, especially in sub-tropical environments. This study investigated the long-term impact of harvest residue retention on tree nutrition, growth and productivity of a F1 hybrid (Pinus elliottii var. elliottii × Pinus caribaea var. hondurensis) exotic pine plantation in sub-tropical Australia, under three harvest residue management regimes: (1) residue removal, RR0; (2) single residue retention, RR1; and (3) double residue retention, RR2. The experiment, established in 1996, is a randomised complete block design with 4 replicates. Tree growth measurements in this study were carried out at ages 2, 4, 6, 8 and 10 years, while foliar nutrient analyses were carried out at ages 2, 4, 6 and 10 years. Litter production and litter nitrogen (N) and phosphorus (P) measurements were carried out quarterly over a 15-month period between ages 9 and 10 years. Results showed that total tree growth was still greater in residue-retained treatments compared to the RR0 treatment. However, mean annual increments of diameter at breast height (MAID) and basal area (MAIB) declined significantly after age 4 years to about 68-78% at age 10 years. Declining foliar N and P concentrations accounted for 62% (p < 0.05) of the variation of growth rates after age 4 years, and foliar N and P concentrations were either marginal or below critical concentrations. In addition, litter production, and litter N and P contents were not significantly different among the treatments. This study suggests that the impact of residue retention on tree nutrition and growth rates might be limited over a longer period, and that the integration of alternative forest management practices is necessary to sustain the benefits of harvest residues until the end of the rotation.

The effect of initial spacing and thinning on wood quality and graded sawn recovery of mature Caribbean pine grown in Queensland.

A mature Caribbean pine (Pinus caribaea var. hondurensis) silviculture experiment provided initial square spacing treatments of 1.8 m2, 2.4 m2, 3.0 m2 and 3.6 m2 (equal to 3088, 1737, 1111 and 772 stems/ha) that were thinned at age 10 years to 600, 400 and 200 stems/ha, retaining an unthinned control for each initial spacing. The trial was destructively sampled at age of 28 years and discs taken along 8 various stem heights were analysed for variation in basic density and SilviScan wood properties. In addition, the logs from ten stocking × thinning treatments were processed in a sawing study. Results indicate thinning effects were generally more pronounced than initial spacing effects. Fast growing trees produced wood with significantly higher average wood densities and higher average stiffness values. Detailed SilviScan densitometry results obtained radially and at various stem heights enabled construction of tree maps for wood properties, providing insights into the variation in juvenile to mature wood proportion across the initial and post-thinning stocking treatments studied. Dried dressed recovery was strongly related to tree size, and log value decreased consistently from butt to top logs across all treatments. The estimated value per hectare was highest in unthinned plots due to values being multiplied by high stem numbers per hectare. However, a complete economic analysis considering all cost structures is required to investigate the optimal silviculture to maximise economic returns to growers and processors. Improved understanding of the relationship between initial spacing, post-thinning stocking and wood and end-product quality should help to customize future forest management strategies required to produce better quality wood and wood products.

Effects of weed control and fertilization at early establishment on tree nitrogen and water use in an exotic F1 hybrid pine of subtropical Australia

Purpose We investigated the effects of weed control and fertilization at early establishment on foliar stable carbon (δ13C) and nitrogen (N) isotope (δ15N) compositions, foliar N concentration, tree growth and biomass, relative weed cover and other physiological traits in a 2-year old F1 hybrid (Pinus elliottii var. elliottii (Engelm) × Pinus caribaea var. hondurensis (Barr. ex Golf.)) plantation grown on a yellow earth in southeast Queensland of subtropical Australia. Materials and methods Treatments included routine weed control, luxury weed control, intermediate weed control, mechanical weed control, nil weed control, and routine and luxury fertilization in a randomised complete block design. Initial soil nutrition and soil fertility parameters included (hot water extractable organic carbon (C) and total nitrogen (N), total C and N, C/N ratio, labile N pools (nitrate (NO3 −) and ammonium (NH4 +)), extractable potassium (K+)), soil δ15N and δ13C. Relative weed cover, foliar N concentrations, tree growth rate and physiological parameters including photosynthesis, stomatal conductance, photosynthetic nitrogen use efficiency, foliar δ15N and foliar δ13C were also measured at early establishment. Results and discussion Foliar N concentration at 1.25 years was significantly different amongst the weed control treatments and was negatively correlated to the relative weed cover at 1.1 years. Foliar N concentration was also positively correlated to foliar δ15N and foliar δ13C, tree height, height growth rates and tree biomass. Foliar δ15N was negatively correlated to the relative weed cover at 0.8 and 1.1 years. The physiological measurements indicated that luxury fertilization and increasing weed competition on these soils decreased leaf xylem pressure potential (Ψxpp) when compared to the other treatments. Conclusions These results indicate how increasing N resources and weed competition have implications for tree N and water use at establishment in F1 hybrid plantations of southeast Queensland, Australia. These results suggest the desirability of weed control, in the inter-planting row, in the first year to maximise site N and water resources available for seedling growth. It also showed the need to avoid over-fertilisation, which interfered with the balance between available N and water on these soils.

Physical Vapor Deposited Thin Films of Lignins Extracted from Sugar Cane Bagasse: Morphology, Electrical Properties, and Sensing Applications

The concern related to the environmental degradation and to the exhaustion of natural resources has induced the research on biodegradable materials obtained from renewable sources, which involves fundamental properties and general application. In this context, we have fabricated thin films of lignins, which were extracted from sugar cane bagasse via modified organosolv process using ethanol as organic solvent. The films were made using the vacuum thermal evaporation technique (PVD, physical vapor deposition) grown up to 120 nm. The main objective was to explore basic properties such as electrical and surface morphology and the sensing performance of these lignins as transducers. The PVD film growth was monitored via ultraviolet-visible (UV-vis) absorption spectroscopy and quartz crystal microbalance, revealing a linear relationship between absorbance and film thickness. The 120 nm lignin PVD film morphology presented small aggregates spread all over the film surface on the nanometer scale (atomic force microscopy, AFM) and homogeneous on the micrometer scale (optical microscopy). The PVD films were deposited onto Au interdigitated electrode (IDE) for both electrical characterization and sensing experiments. In the case of electrical characterization, current versus voltage (I vs V) dc measurements were carried out for the Au IDE coated with 120 nm lignin PVD film, leading to a conductivity of 3.6 x 10(-10) S/m. Using impedance spectroscopy, also for the Au IDE coated with the 120 nm lignin PVD film, dielectric constant of 8.0, tan delta of 3.9 x 10(-3)) and conductivity of 1.75 x 10(-9) S/m were calculated at 1 kHz. As a proof-of-principle, the application of these lignins as transducers in sensing devices was monitored by both impedance spectroscopy (capacitance vs frequency) and I versus time dc measurements toward aniline vapor (saturated atmosphere). The electrical responses showed that the sensing units are sensible to aniline vapor with the process being reversible. AFM images conducted directly onto the sensing units (Au IDE coated with 120 nm lignin PVD film) before and after the sensing experiments showed a decrease in the PVD film roughness from 5.8 to 3.2 nm after exposing to aniline.

Charcoal production using tropical pine thinnings

In Brazil, the wood from pine-plantation thinnings is difficult to sell. However, these wood thinnings could be used to produce charcoal. The physical and chemical properties of charcoal produced from logs or first and fourth thinnings of Pinus caribaea var. hondurensis and Pinus oocarpa were determined. Similar properties were also determined for sawmill slabs cut from first and fourth thinnings. Properties were compared to charcoal made from pine materials and 7-yr-old Eucalyptus grandis. Results show that Pinus spp had better chemical properties than did E. grandis. In contrast, charcoal obtained from E. grandis had higher values of apparent density and lower values of bulk density than did Pinus spp. © 1992.

Avaliação da distribuição da densidade em MDF a partir da técnica da onda de ultra-som

The goal of this research was to determine the density distribution in medium density fiberboard (MDF), manufactured with polyurethane derived from castor oil using, ultrasonic wave technique. The equipment used in this test is Steinkamp BP7 with plan and exponential transducers, both with 45 kHz frequencies, located in several zones on the plate in order to determine wave ultrasonic velocity. The Pinus caribaea and Eucalyptus grandis fiberboard were manufactured in the quality control and products development laboratory of Duratex with 500 mm long, 500 mm large, 8 and 15 mm of thickness. Three MDF for each fiber specimen and thickness were fabricated, totalizing twelve plates tested. The MDF were produced with 5% polyurethane addition, in temperature of 160°C, tension press of 53 bars and addition of moisture content of 12%. For determination of fiberboard density, samples were extracted from the same zones where the wave ultrasonic velocity was determined. In this case, DAX-Ray equipment was used. Statistical analysis shows good agreement with wave ultrasonic velocity and the density profile, validating the application of non-destructive technique in order to determine the density profile of MDF's.

Performance of 19-year-old provenances of Liquidambar styraciflua in Paraguaçu Paulista, São Paulo

The genetic variation in the growth of seven 19-year-old Liquidambar styraciflua provenances was studied in Paraguaçu Paulista, São Paulo State, Brazil. The trial was established in a complete randomized block design with seven provenances, four replications and twelve-tree square plots. Significant differences among provenances were detected for diameter at breast height, height and volume, indicating the possibility of increasing timber yield through selection of the most productive provenances. Genetic correlations between growth traits were high and statistically significant. The provenance from Finca las Victorias, Guatemala had the best and the provenance from Franklin, Virginia, United States the poorest performance for all traits. A growth comparison of Pinus caribaea var. bahamensis with the best provenance at the same site indicated that the potential of L. styraciflua for silviculture in the region of Paraguaçu Paulista is high.

Emprego da reflectometria por domínio do tempo na determinação da umidade de madeiras comerciais

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Emprego de ferramentas numéricas na avaliação do módulo de elasticidade em vigas roliças de madeira

Vigas são elementos estruturais encontrados na maioria das construções civis. Dentre os materiais de engenharia, destaca-se a madeira, por ter resistência mecânica satisfatória aliada a baixa densidade. A madeira roliça apresenta-se como boa solução na confecção de vigas, uma vez que não precisa ser processada, como é o caso da madeira serrada. O projeto de elementos estruturais de madeira requer o conhecimento de suas propriedades físicas e mecânicas, obtidas segundo as premissas de documentos normativos. Em se tratando da madeira roliça, os documentos normativos nacionais que tratam da determinação das propriedades de resistência e rigidez estão vigentes há mais de vinte anos sem revisão técnica. De forma geral, tanto as normas nacionais como as internacionais idealizam geometria troncocônica para as peças roliças de madeira, implicando equações simplificadas incapazes de prever a influência das irregularidades da forma na determinação do módulo de elasticidade longitudinal. Este trabalho objetiva avaliar a influência das irregularidades da geometria em peças roliças de madeira Corymbia citriodora e Pinus caribaea no cálculo do módulo de elasticidade longitudinal. Para tanto, utilizou-se do ensaio de flexão estática a três pontos, considerando também um modelo matemático simplificado, assumindo seção circular constante para a forma do elemento. As irregularidades das peças são consideradas nos modelos numéricos, constituídos de elementos finitos de barra e tridimensionais. Os resultados encontrados revelam equivalência estatística entre os módulos de elasticidade para ambas as formas de cálculo, indicando ser plausível a consideração de seção circular constante para as peças de madeira aqui avaliadas.

Cellular stages of root formation, root system quality and survival of Pinus elliottii var. elliottii x P. caribaea var. hondurensis cuttings in different temperature environments.

Time to first root in cuttings varies under different environmental conditions and understanding these differences is critical for optimizing propagation of commercial forestry species. Temperature environment (15, 25, 30 or 35 +/- A 2A degrees C) had no effect on the cellular stages in root formation of the Slash x Caribbean Pine hybrid over 16 weeks as determined by histology. Initially callus cells formed in the cortex, then tracheids developed and formed primordia leading to external roots. However, speed of development followed a growth curve with the fastest development occurring at 25A degrees C and slowest at 15A degrees C with rooting percentages at week 12 of 80 and 0% respectively. Cutting survival was good in the three cooler temperature regimes (> 80%) but reduced to 59% at 35A degrees C. Root formation appeared to be dependant on the initiation of tracheids because all un-rooted cuttings had callus tissue but no tracheids, irrespective of temperature treatment and clone.

Fuel manipulation with herbicide treatments to reduce fire hazard in young pine (Pinus elliottii × P. caribaea) plantations in south-east Queensland, Australia

Wildfire represents a major risk to pine plantations. This risk is particularly great for young plantations (generally less than 10 m in height) where prescribed fire cannot be used to manipulate fuel biomass, and where flammable grasses are abundant in the understorey. We report results from a replicated field experiment designed to determine the effects of two rates of glyphosate (450 g L–1) application, two extents of application (inter-row only and inter-row and row) with applications being applied once or twice, on understorey fine fuel biomass, fuel structure and composition in south-east Queensland, Australia. Two herbicide applications (~9 months apart) were more effective than a once-off treatment for reducing standing biomass, grass continuity, grass height, percentage grass dry weight and the density of shrubs. In addition, the 6-L ha–1 rate of application was more effective than the 3-L ha–1 rate of application in periodically reducing grass continuity and shrub density in the inter-rows and in reducing standing biomass in the tree rows, and application in the inter-rows and rows significantly reduced shrub density relative to the inter-row-only application. Herbicide treatment in the inter-rows and rows is likely to be useful for managing fuels before prescribed fire in young pine plantations because such treatment minimised tree scorch height during prescribed burns. Further, herbicide treatments had no adverse effects on plantation trees, and in some cases tree growth was enhanced by treatments. However, the effectiveness of herbicide treatments in reducing the risk of tree damage or mortality under wildfire conditions remains untested.