Modelling and simulation of biomass gasification in a circulating fluidized bed reactor

Computational Fluid Dynamics (CFD) has found great acceptance among the engineering community as a tool for research and design of processes that are practically difficult or expensive to study experimentally. One of these processes is the biomass gasification in a Circulating Fluidized Bed (CFB). Biomass gasification is the thermo-chemical conversion of biomass at a high temperature and a controlled oxygen amount into fuel gas, also sometime referred to as syngas. Circulating fluidized bed is a type of reactor in which it is possible to maintain a stable and continuous circulation of solids in a gas-solid system. The main objectives of this thesis are four folds: (i) Develop a three-dimensional predictive model of biomass gasification in a CFB riser using advanced Computational Fluid Dynamic (CFD) (ii) Experimentally validate the developed hydrodynamic model using conventional and advanced measuring techniques (iii) Study the complex hydrodynamics, heat transfer and reaction kinetics through modelling and simulation (iv) Study the CFB gasifier performance through parametric analysis and identify the optimum operating condition to maximize the product gas quality. Two different and complimentary experimental techniques were used to validate the hydrodynamic model, namely pressure measurement and particle tracking. The pressure measurement is a very common and widely used technique in fluidized bed studies, while, particle tracking using PEPT, which was originally developed for medical imaging, is a relatively new technique in the engineering field. It is relatively expensive and only available at few research centres around the world. This study started with a simple poly-dispersed single solid phase then moved to binary solid phases. The single solid phase was used for primary validations and eliminating unnecessary options and steps in building the hydrodynamic model. Then the outcomes from the primary validations were applied to the secondary validations of the binary mixture to avoid time consuming computations. Studies on binary solid mixture hydrodynamics is rarely reported in the literature. In this study the binary solid mixture was modelled and validated using experimental data from the both techniques mentioned above. Good agreement was achieved with the both techniques. According to the general gasification steps the developed model has been separated into three main gasification stages; drying, devolatilization and tar cracking, and partial combustion and gasification. The drying was modelled as a mass transfer from the solid phase to the gas phase. The devolatilization and tar cracking model consist of two steps; the devolatilization of the biomass which is used as a single reaction to generate the biomass gases from the volatile materials and tar cracking. The latter is also modelled as one reaction to generate gases with fixed mass fractions. The first reaction was classified as a heterogeneous reaction while the second reaction was classified as homogenous reaction. The partial combustion and gasification model consisted of carbon combustion reactions and carbon and gas phase reactions. The partial combustion considered was for C, CO, H2 and CH4. The carbon gasification reactions used in this study is the Boudouard reaction with CO2, the reaction with H2O and Methanation (Methane forming reaction) reaction to generate methane. The other gas phase reactions considered in this study are the water gas shift reaction, which is modelled as a reversible reaction and the methane steam reforming reaction. The developed gasification model was validated using different experimental data from the literature and for a wide range of operating conditions. Good agreement was observed, thus confirming the capability of the model in predicting biomass gasification in a CFB to a great accuracy. The developed model has been successfully used to carry out sensitivity and parametric analysis. The sensitivity analysis included: study of the effect of inclusion of various combustion reaction; and the effect of radiation in the gasification reaction. The developed model was also used to carry out parametric analysis by changing the following gasifier operating conditions: fuel/air ratio; biomass flow rates; sand (heat carrier) temperatures; sand flow rates; sand and biomass particle sizes; gasifying agent (pure air or pure steam); pyrolysis models used; steam/biomass ratio. Finally, based on these parametric and sensitivity analysis a final model was recommended for the simulation of biomass gasification in a CFB riser.

Comparative analysis of experimental and modelling of gas-solid flow hydrodynamics:effect of friction and interparticle cohesion forces

The effect of friction and interparticle cohesion forces on the gas-solid flow hydrodynamics was discussed. A proposed interparticle cohesion and frictional force terms have been tested in a continuum fully developed flow model to investigate their effect on the general hydrodynamic features of vertical duct flow. It was observed that both terms have direct effect on lowering the material carryover, which implies a reduced bed expansion in freely bubbling column. The parametric analysis shows that cohesion and frictional forces are high when compared to kinetic stress and hence it can play a major role in describing the hydrodynamics features of the flow.

Parametric CAD model based shape optimization using adjoint functions

Adjoint methods have proven to be an efficient way of calculating the gradient of an objective function with respect to a shape parameter for optimisation, with a computational cost nearly independent of the number of the design variables [1]. The approach in this paper links the adjoint surface sensitivities (gradient of objective function with respect to the surface movement) with the parametric design velocities (movement of the surface due to a CAD parameter perturbation) in order to compute the gradient of the objective function with respect to CAD variables.
For a successful implementation of shape optimization strategies in practical industrial cases, the choice of design variables or parameterisation scheme used for the model to be optimized plays a vital role. Where the goal is to base the optimization on a CAD model the choices are to use a NURBS geometry generated from CAD modelling software, where the position of the NURBS control points are the optimisation variables [2] or to use the feature based CAD model with all of the construction history to preserve the design intent [3]. The main advantage of using the feature based model is that the optimized model produced can be directly used for the downstream applications including manufacturing and process planning.
This paper presents an approach for optimization based on the feature based CAD model, which uses CAD parameters defining the features in the model geometry as the design variables. In order to capture the CAD surface movement with respect to the change in design variable, the “Parametric Design Velocity” is calculated, which is defined as the movement of the CAD model boundary in the normal direction due to a change in the parameter value.
The approach presented here for calculating the design velocities represents an advancement in terms of capability and robustness of that described by Robinson et al. [3]. The process can be easily integrated to most industrial optimisation workflows and is immune to the topology and labelling issues highlighted by other CAD based optimisation processes. It considers every continuous (“real value”) parameter type as an optimisation variable, and it can be adapted to work with any CAD modelling software, as long as it has an API which provides access to the values of the parameters which control the model shape and allows the model geometry to be exported. To calculate the movement of the boundary the methodology employs finite differences on the shape of the 3D CAD models before and after the parameter perturbation. The implementation procedure includes calculating the geometrical movement along a normal direction between two discrete representations of the original and perturbed geometry respectively. Parametric design velocities can then be directly linked with adjoint surface sensitivities to extract the gradients to use in a gradient-based optimization algorithm.
The optimisation of a flow optimisation problem is presented, in which the power dissipation of the flow in an automotive air duct is to be reduced by changing the parameters of the CAD geometry created in CATIA V5. The flow sensitivities are computed with the continuous adjoint method for a laminar and turbulent flow [4] and are combined with the parametric design velocities to compute the cost function gradients. A line-search algorithm is then used to update the design variables and proceed further with optimisation process.

Modelling and estimating models of physician labour supply and productivity

Ma thèse s’intéresse aux politiques de santé conçues pour encourager l’offre de services de santé. L’accessibilité aux services de santé est un problème majeur qui mine le système de santé de la plupart des pays industrialisés. Au Québec, le temps médian d’attente entre une recommandation du médecin généraliste et un rendez-vous avec un médecin spécialiste était de 7,3 semaines en 2012, contre 2,9 semaines en 1993, et ceci malgré l’augmentation du nombre de médecins sur cette même période. Pour les décideurs politiques observant l’augmentation du temps d’attente pour des soins de santé, il est important de comprendre la structure de l’offre de travail des médecins et comment celle-ci affecte l’offre des services de santé. Dans ce contexte, je considère deux principales politiques. En premier lieu, j’estime comment les médecins réagissent aux incitatifs monétaires et j’utilise les paramètres estimés pour examiner comment les politiques de compensation peuvent être utilisées pour déterminer l’offre de services de santé de court terme. En second lieu, j’examine comment la productivité des médecins est affectée par leur expérience, à travers le mécanisme du "learning-by-doing", et j’utilise les paramètres estimés pour trouver le nombre de médecins inexpérimentés que l’on doit recruter pour remplacer un médecin expérimenté qui va à la retraite afin de garder l’offre des services de santé constant. Ma thèse développe et applique des méthodes économique et statistique afin de mesurer la réaction des médecins face aux incitatifs monétaires et estimer leur profil de productivité (en mesurant la variation de la productivité des médecins tout le long de leur carrière) en utilisant à la fois des données de panel sur les médecins québécois, provenant d’enquêtes et de l’administration. Les données contiennent des informations sur l’offre de travail de chaque médecin, les différents types de services offerts ainsi que leurs prix. Ces données couvrent une période pendant laquelle le gouvernement du Québec a changé les prix relatifs des services de santé. J’ai utilisé une approche basée sur la modélisation pour développer et estimer un modèle structurel d’offre de travail en permettant au médecin d’être multitâche. Dans mon modèle les médecins choisissent le nombre d’heures travaillées ainsi que l’allocation de ces heures à travers les différents services offerts, de plus les prix des services leurs sont imposés par le gouvernement. Le modèle génère une équation de revenu qui dépend des heures travaillées et d’un indice de prix représentant le rendement marginal des heures travaillées lorsque celles-ci sont allouées de façon optimale à travers les différents services. L’indice de prix dépend des prix des services offerts et des paramètres de la technologie de production des services qui déterminent comment les médecins réagissent aux changements des prix relatifs. J’ai appliqué le modèle aux données de panel sur la rémunération des médecins au Québec fusionnées à celles sur l’utilisation du temps de ces mêmes médecins. J’utilise le modèle pour examiner deux dimensions de l’offre des services de santé. En premierlieu, j’analyse l’utilisation des incitatifs monétaires pour amener les médecins à modifier leur production des différents services. Bien que les études antérieures ont souvent cherché à comparer le comportement des médecins à travers les différents systèmes de compensation,il y a relativement peu d’informations sur comment les médecins réagissent aux changementsdes prix des services de santé. Des débats actuels dans les milieux de politiques de santé au Canada se sont intéressés à l’importance des effets de revenu dans la détermination de la réponse des médecins face à l’augmentation des prix des services de santé. Mon travail contribue à alimenter ce débat en identifiant et en estimant les effets de substitution et de revenu résultant des changements des prix relatifs des services de santé. En second lieu, j’analyse comment l’expérience affecte la productivité des médecins. Cela a une importante implication sur le recrutement des médecins afin de satisfaire la demande croissante due à une population vieillissante, en particulier lorsque les médecins les plus expérimentés (les plus productifs) vont à la retraite. Dans le premier essai, j’ai estimé la fonction de revenu conditionnellement aux heures travaillées, en utilisant la méthode des variables instrumentales afin de contrôler pour une éventuelle endogeneité des heures travaillées. Comme instruments j’ai utilisé les variables indicatrices des âges des médecins, le taux marginal de taxation, le rendement sur le marché boursier, le carré et le cube de ce rendement. Je montre que cela donne la borne inférieure de l’élasticité-prix direct, permettant ainsi de tester si les médecins réagissent aux incitatifs monétaires. Les résultats montrent que les bornes inférieures des élasticités-prix de l’offre de services sont significativement positives, suggérant que les médecins répondent aux incitatifs. Un changement des prix relatifs conduit les médecins à allouer plus d’heures de travail au service dont le prix a augmenté. Dans le deuxième essai, j’estime le modèle en entier, de façon inconditionnelle aux heures travaillées, en analysant les variations des heures travaillées par les médecins, le volume des services offerts et le revenu des médecins. Pour ce faire, j’ai utilisé l’estimateur de la méthode des moments simulés. Les résultats montrent que les élasticités-prix direct de substitution sont élevées et significativement positives, représentant une tendance des médecins à accroitre le volume du service dont le prix a connu la plus forte augmentation. Les élasticitésprix croisées de substitution sont également élevées mais négatives. Par ailleurs, il existe un effet de revenu associé à l’augmentation des tarifs. J’ai utilisé les paramètres estimés du modèle structurel pour simuler une hausse générale de prix des services de 32%. Les résultats montrent que les médecins devraient réduire le nombre total d’heures travaillées (élasticité moyenne de -0,02) ainsi que les heures cliniques travaillées (élasticité moyenne de -0.07). Ils devraient aussi réduire le volume de services offerts (élasticité moyenne de -0.05). Troisièmement, j’ai exploité le lien naturel existant entre le revenu d’un médecin payé à l’acte et sa productivité afin d’établir le profil de productivité des médecins. Pour ce faire, j’ai modifié la spécification du modèle pour prendre en compte la relation entre la productivité d’un médecin et son expérience. J’estime l’équation de revenu en utilisant des données de panel asymétrique et en corrigeant le caractère non-aléatoire des observations manquantes à l’aide d’un modèle de sélection. Les résultats suggèrent que le profil de productivité est une fonction croissante et concave de l’expérience. Par ailleurs, ce profil est robuste à l’utilisation de l’expérience effective (la quantité de service produit) comme variable de contrôle et aussi à la suppression d’hypothèse paramétrique. De plus, si l’expérience du médecin augmente d’une année, il augmente la production de services de 1003 dollar CAN. J’ai utilisé les paramètres estimés du modèle pour calculer le ratio de remplacement : le nombre de médecins inexpérimentés qu’il faut pour remplacer un médecin expérimenté. Ce ratio de remplacement est de 1,2.

Time domain decomposition for European options in financial modelling

Finance is one of the fastest growing areas in modern applied mathematics with real world applications. The interest of this branch of applied mathematics is best described by an example involving shares. Shareholders of a company receive dividends which come from the profit made by the company. The proceeds of the company, once it is taken over or wound up, will also be distributed to shareholders. Therefore shares have a value that reflects the views of investors about the likely dividend payments and capital growth of the company. Obviously such value will be quantified by the share price on stock exchanges. Therefore financial modelling serves to understand the correlations between asset and movements of buy/sell in order to reduce risk. Such activities depend on financial analysis tools being available to the trader with which he can make rapid and systematic evaluation of buy/sell contracts. There are other financial activities and it is not an intention of this paper to discuss all of these activities. The main concern of this paper is to propose a parallel algorithm for the numerical solution of an European option. This paper is organised as follows. First, a brief introduction is given of a simple mathematical model for European options and possible numerical schemes of solving such mathematical model. Second, Laplace transform is applied to the mathematical model which leads to a set of parametric equations where solutions of different parametric equations may be found concurrently. Numerical inverse Laplace transform is done by means of an inversion algorithm developed by Stehfast. The scalability of the algorithm in a distributed environment is demonstrated. Third, a performance analysis of the present algorithm is compared with a spatial domain decomposition developed particularly for time-dependent heat equation. Finally, a number of issues are discussed and future work suggested.

Advanced parametrical modelling of 24 GHz radar sensor IC packaging components

This paper deals with the development of an advanced parametrical modelling concept for packaging components of a 24 GHz radar sensor IC used in automotive driver assistance systems. For fast and efficient design of packages for system-in-package modules (SiP), a simplified model for the description of parasitic electromagnetic effects within the package is desirable, as 3-D field computation becomes inefficient due to the high density of conductive elements of the various signal paths in the package. By using lumped element models for the characterization of the conductive components, a fast indication of the design's signal-quality can be gained, but so far does not offer enough flexibility to cover the whole range of geometric arrangements of signal paths in a contemporary package. This work pursues to meet the challenge of developing a flexible and fast package modelling concept by defining parametric lumped-element models for all basic signal path components, e.g. bond wires, vias, strip lines, bumps and balls. © Author(s) 2011. CC Attribution 3.0 License.

Optimizing fused deposition modelling: the impact of geometrical slicing parameters on mechanical properties

This comprehensive study explores the intricate world of 3D printing, with a focus on Fused Deposition Modelling (FDM). It sheds light on the critical factors that influence the quality and mechanical properties of 3D printed objects. Using an optical microscope with 40X magnification, the shapes of the printed beads is correlated to specific slicing parameters, resulting in a 2D parametric model. This mathematical model, derived from real samples, serves as a tool to predict general mechanical behaviour, bridging the gap between theory and practice in FDM printing. The study begins by emphasising the importance of geometric parameters such as layer height, line width and filament tolerance on the final printed bead geometry and the resulting theoretical effect on mechanical properties. The introduction of VPratio parameter (ratio between the area of the voids and the area occupied by printed material) allows the quantification of the variation of geometric slicing parameters on the improvement or reduction of mechanical properties. The study also addresses the effect of overhang and the role of filament diameter tolerances. The research continues with the introduction of 3D FEM (Finite Element Analysis) models based on the RVE (Representative Volume Element) to verify the results obtained from the 2D model and to analyse other aspects that affect mechanical properties and not directly observable with the 2D model. The study also proposes a model for the examination of 3D printed infill structures, introducing also an innovative methodology called “double RVE” which speeds up the calculation of mechanical properties and is also more computationally efficient. Finally, the limitations of the RVE model are shown and a so-called Hybrid RVE-based model is created to overcome the limitations and inaccuracy of the conventional RVE model and homogenization procedure on some printed geometries.

The Basic Reproduction Number Obtained From Jacobian And Next Generation Matrices - A Case Study Of Dengue Transmission Modelling.

The basic reproduction number is a key parameter in mathematical modelling of transmissible diseases. From the stability analysis of the disease free equilibrium, by applying Routh-Hurwitz criteria, a threshold is obtained, which is called the basic reproduction number. However, the application of spectral radius theory on the next generation matrix provides a different expression for the basic reproduction number, that is, the square root of the previously found formula. If the spectral radius of the next generation matrix is defined as the geometric mean of partial reproduction numbers, however the product of these partial numbers is the basic reproduction number, then both methods provide the same expression. In order to show this statement, dengue transmission modelling incorporating or not the transovarian transmission is considered as a case study. Also tuberculosis transmission and sexually transmitted infection modellings are taken as further examples.

Parametric model for the analysis of concrete expansion due to alkali-aggregate reaction

The alkali-aggregate reaction (AAR) is a chemical reaction that provokes a heterogeneous expansion of concrete and reduces important properties such as Young's modulus, leading to a reduction in the structure's useful life. In this study, a parametric model is employed to determine the spatial distribution of the concrete expansion, combining normalized factors that influence the reaction through an AAR expansion law. Optimization techniques were employed to adjust the numerical results and observations in a real structure. A three-dimensional version of the model has been implemented in a finite element commercial package (ANSYS(C)) and verified in the analysis of an accelerated mortar test. Comparisons were made between two AAR mathematical descriptions for the mechanical phenomenon, using the same methodology, and an expansion curve obtained from experiment. Some parametric studies are also presented. The numerical results compared very well with the experimental data validating the proposed method.

Effects of Variations in Nonlinear Damping Coefficients on the Parametric Vibration of a Cantilever Beam with a Lumped Mass

Uncertainties in damping estimates can significantly affect the dynamic response of a given flexible structure. A common practice in linear structural dynamics is to consider a linear viscous damping model as the major energy dissipation mechanism. However, it is well known that different forms of energy dissipation can affect the structure's dynamic response. The major goal of this paper is to address the effects of the turbulent frictional damping force, also known as drag force on the dynamic behavior of a typical flexible structure composed of a slender cantilever beam carrying a lumped-mass on the tip. First, the system's analytical equation is obtained and solved by employing a perturbation technique. The solution process considers variations of the drag force coefficient and its effects on the system's response. Then, experimental results are presented to demonstrate the effects of the nonlinear quadratic damping due to the turbulent frictional force on the system's dynamic response. In particular, the effects of the quadratic damping on the frequency-response and amplitude-response curves are investigated. Numerically simulated as well as experimental results indicate that variations on the drag force coefficient significantly alter the dynamics of the structure under investigation. Copyright (c) 2008 D. G. Silva and P. S. Varoto.

Importance of considering a material micro-failure criterion in the numerical modelling of the shot peening process applied to parabolic leaf springs

Shot peening is a cold-working mechanical process in which a shot stream is propelled against a component surface. Its purpose is to introduce compressive residual stresses on component surfaces for increasing the fatigue resistance. This process is widely applied in springs due to the cyclical loads requirements. This paper presents a numerical modelling of shot peening process using the finite element method. The results are compared with experimental measurements of the residual stresses, obtained by the X-rays diffraction technique, in leaf springs submitted to this process. Furthermore, the results are compared with empirical and numerical correlations developed by other authors.

Scalable continuous-variable entanglement of light beams produced by optical parametric oscillators

We show that scalable multipartite entanglement among light fields may be generated by optical parametric oscillators (OPOs). The tripartite entanglement existent among the three bright beams produced by a single OPO-pump, signal, and idler-is scalable to a system of many OPOs by pumping them in cascade with the same optical field. This latter serves as an entanglement distributor. The special case of two OPOs is studied, as it is shown that the resulting five bright beams share genuine multipartite entanglement. In addition, the structure of entanglement distribution among the fields can be manipulated to some degree by tuning the incident pump power. The scalability to many fields is straightforward, allowing an alternative implementation of a multipartite quantum information network with continuous variables.

A contribution for thermoeconomic modelling: A methodology proposal

This work presents a thermoeconomic optimization methodology for the analysis and design of energy systems. This methodology involves economic aspects related to the exergy conception, in order to develop a tool to assist the equipment selection, operation mode choice as well as to optimize the thermal plants design. It also presents the concepts related to exergy in a general scope and in thermoeconomics which combines the thermal sciences principles (thermodynamics, heat transfer, and fluid mechanics) and the economic engineering in order to rationalize energy systems investment decisions, development and operation. Even in this paper, it develops a thermoeconomic methodology through the use of a simple mathematical model, involving thermodynamics parameters and costs evaluation, also defining the objective function as the exergetic production cost. The optimization problem evaluation is developed for two energy systems. First is applied to a steam compression refrigeration system and then to a cogeneration system using backpressure steam turbine. (C) 2010 Elsevier Ltd. All rights reserved.

Thermal error evaluation and modelling of a CNC cylindrical grinding machine

With the relentless quest for improved performance driving ever tighter tolerances for manufacturing, machine tools are sometimes unable to meet the desired requirements. One option to improve the tolerances of machine tools is to compensate for their errors. Among all possible sources of machine tool error, thermally induced errors are, in general for newer machines, the most important. The present work demonstrates the evaluation and modelling of the behaviour of the thermal errors of a CNC cylindrical grinding machine during its warm-up period.

Performance of the Equivalent Reservoir Modelling Technique for Multi-Reservoir Hydropower Systems

This paper investigates the validity of a simplified equivalent reservoir representation of a multi-reservoir hydroelectric system for modelling its optimal operation for power maximization. This simplification, proposed by Arvanitidis and Rosing (IEEE Trans Power Appar Syst 89(2):319-325, 1970), imputes a potential energy equivalent reservoir with energy inflows and outflows. The hydroelectric system is also modelled for power maximization considering individual reservoir characteristics without simplifications. Both optimization models employed MINOS package for solution of the non-linear programming problems. A comparison between total optimized power generation over the planning horizon by the two methods shows that the equivalent reservoir is capable of producing satisfactory power estimates with less than 6% underestimation. The generation and total reservoir storage trajectories along the planning horizon obtained by equivalent reservoir method, however, presented significant discrepancies as compared to those found in the detailed modelling. This study is motivated by the fact that Brazilian generation system operations are based on the equivalent reservoir method as part of the power dispatch procedures. The potential energy equivalent reservoir is an alternative which eliminates problems with the dimensionality of state variables in a dynamic programming model.