High pressure and low temperature study of ammonia borane and lithium amidoborane

Hydrogen has been considered as a potentially efficient and environmentally friendly alternative energy solution. However, one of the most important scientific and technical challenges that the "hydrogen economy" faces is the development of safe and economically viable on-board hydrogen storage for fuel cell applications, especially to the transportation sector. Ammonia borane (BH3NH 3), a solid state hydrogen storage material, possesses exceptionally high hydrogen content (19.6 wt%).However, a fairly high temperature is required to release all the hydrogen atoms, along with the emission of toxic borazine. Recently research interests are focusing on the improvement of H2 discharge from ammonia borane (AB) including lowering the dehydrogenation temperature and enhancing hydrogen release rate using different techniques. Till now the detailed information about the bonding characteristics of AB is not sufficient to understand details about its phases and structures. ^ Elemental substitution of ammonia borane produces metal amidoboranes. Introduction of metal atoms to the ammonia borane structure may alter the bonding characteristics. Lithium amidoborane is synthesized by ball milling of ammonia borane and lithium hydride. High pressure study of molecular crystal provides unique insight into the intermolecular bonding forces and phase stability. During this dissertation, Raman spectroscopic study of lithium amidoborane has been carried out at high pressure in a diamond anvil cell. It has been identified that there is no dihydrogen bond in the lithium amidoborane structure, whereas dihydrogen bond is the characteristic bond of the parent compound ammonia borane. It has also been identified that the B-H bond becomes weaker, whereas B-N and N-H bonds become stronger than those in the parent compound ammonia borane. At high pressure up to 15 GPa, Raman spectroscopic study indicates two phase transformations of lithium amidoborane, whereas synchrotron X-ray diffraction data indicates only one phase transformation of this material. ^ Pressure and temperature has a significant effect on the structural stability of ammonia borane. This dissertation explored the phase transformation behavior of ammonia borane at high pressure and low temperature using in situ Raman spectroscopy. The P-T phase boundary between the tetragonal (I4mm) and orthorhombic (Pmn21) phases of ammonia borane has been determined. The transition has a positive Clapeyron slope which indicates the transition is of exothermic in nature. Influence of nanoconfinemment on the I4mm to Pmn2 1 phase transition of ammonia borane was also investigated. Mesoporus silica scaffolds SBA-15 with pore size of ~8 nm and MCM-41 with pore size of 2.1-2.7 nm, were used to nanoconfine ammonia borane. During cooling down, the I4mm to Pmn21 phase transition was not observed in MCM-41 nanoconfined ammonia borane, whereas the SBA-15 nanocondfined ammonia borane shows the phase transition at ~195 K. Four new phases of ammonia borane were also identified at high pressure up to 15 GPa and low temperature down to 90 K.^

Volume averaging of multiphase flows with hydrate formation in subsea pipelines

In oil and gas pipeline operations, the gas, oil, and water phases simultaneously move through pipe systems. The mixture cools as it flows through subsea pipelines, and forms a hydrate formation region, where the hydrate crystals start to grow and may eventually block the pipeline. The potential of pipe blockage due to hydrate formation is one of the most significant flow-assurance problems in deep-water subsea operations. Due to the catastrophic safety and economic implications of hydrate blockage, it is important to accurately predict the simultaneous flow of gas, water, and hydrate particles in flowlines. Currently, there are few or no studies that account for the simultaneous effects of hydrate growth and heat transfer on flow characteristics within pipelines. This thesis presents new and more accurate predictive models of multiphase flows in undersea pipelines to describe the simultaneous flow of gas, water, and hydrate particles through a pipeline. A growth rate model for the hydrate phase is presented and then used in the development of a new three-phase model. The conservation equations of mass, momentum, and energy are formulated to describe the physical phenomena of momentum and heat transfer between the fluid and the wall. The governing equations are solved based on an analytical-numerical approach using a Newton-Raphson method for the nonlinear equations. An algorithm was developed in Matlab software to solve the equations from the inlet to the outlet of the pipeline. The developed models are validated against a single-phase model with mixture properties, and the results of comparative studies show close agreement. The new model predicts the volume fraction and velocity of each phase, as well as the mixture pressure and temperature profiles along the length of the pipeline. The results from the hydrate growth model reveal the growth rate and location where the initial hydrates start to form. Finally, to assess the impact of certain parameters on the flow characteristics, parametric studies have been conducted. The results show the effect of a variation in the pipe diameter, mass flow rate, inlet pressure, and inlet temperature on the flow characteristics and hydrate growth rates.

Continuous measurement of carbon dioxid partial pressure in seawater in the region of the Iceland-Faroe Ridge (Table 1)

During the 14th expedition of the research vessel "Meteor" from the 2nd of July to the 7th of August 1968 continously recording instruments for measuring the CO2 partial pressure of seawater and atmospheric CO2 were developped by the Meteorological Institute, University of Frankfurt/M. During the Faroer expedition instrumental constants, such as relative and absolute accuracy, inertia and solvent power were tested. The performance of discontinous analyses of water samples was adopted to shipboard conditiones and correction factors depending on water volume, depth of sampling and water temperature were measured. After having computed average values of the continous records (atmosp. CO2 content, CO2 partial pressure, water temperature) geographical distribution, diurnal variation and dependence of diurnal averages were tested. At four different locations CO2 partial pressure was measured in various depths. During the voyage from the Faroer islands to Helgoland the measured concentrations of atmospheric CO2 content and CO2 partial pressure were tested with respect to a correlation of the geographical latitude.

Gas, water and volume characteristics during controlled degassing experiments on ODP Leg 164 PCS cores

A pressurized core with CH4 hydrate or dissolved CH4 should evolve gas volumes in a predictable manner as pressure is released over time at isothermal conditions. Incremental gas volumes were collected as pressure was released over time from 29 pressure core sampler (PCS) cores from Sites 994, 995, 996, and 997 on the Blake Ridge. Most of these cores were kept at or near 0ºC with an ice bath, and many of these cores yielded substantial quantities of CH4. Volume-pressure plots were constructed for 20 of these cores. Only five plots conform to expected volume and pressure changes for sediment cores with CH4 hydrate under initial pressure and temperature conditions. However, other evidence suggests that sediment in these five and at least five other PCS cores contained CH4 hydrate before core recovery and gas release. Detection of CH4 hydrate in a pressurized sediment core through volume-pressure relationships is complicated by two factors. First, significant quantities of CH4-poor borehole water fill the PCS and come into contact with the core. This leads to dilution of CH4 concentration in interstitial water and, in many cases, decomposition of CH4 hydrate before a degassing experiment begins. Second, degassing experiments were conducted after the PCS had equilibrated in an ice-water bath (0ºC). This temperature is significantly lower than in situ values in the sediment formation before core recovery. Our results and interpretations for PCS cores collected on Leg 164 imply that pressurized containers formerly used by the Deep Sea Drilling Project (DSDP) and currently used by ODP are not appropriately designed for direct detection of gas hydrate in sediment at in situ conditions through volume-pressure relationships.

Cenozoic global ice volume and temperature simulations over the past 40 million years

Variations in global ice volume and temperature over the Cenozoic era have been investigated with a set of one-dimensional (1-D) ice-sheet models. Simulations include three ice sheets representing glaciation in the Northern Hemisphere, i.e. in Eurasia, North America and Greenland, and two separate ice sheets for Antarctic glaciation. The continental mean Northern Hemisphere surface-air temperature has been derived through an inverse procedure from observed benthic d18O records. These data have yielded a mutually consistent and continuous record of temperature, global ice volume and benthic d18O over the past 35 Ma. The simple 1-D model shows good agreement with a comprehensive 3-D ice-sheet model for the past 3 Ma. On average, differences are only 1.0°C for temperature and 6.2 m for sea level. Most notably, over the 35 Ma period, the reconstructed ice volume-temperature sensitivity shows a transition from a climate controlled by Southern Hemisphere ice sheets to one controlled by Northern Hemisphere ice sheets. Although the transient behaviour is important, equilibrium experiments show that the relationship between temperature and sea level is linear and symmetric, providing limited evidence for hysteresis. Furthermore, the results show a good comparison with other simulations of Antarctic ice volume and observed sea level.

High Pressure and Low Temperature Study of Ammonia Borane and Lithium Amidoborane

Hydrogen has been considered as a potentially efficient and environmentally friendly alternative energy solution. However, one of the most important scientific and technical challenges that the “hydrogen economy” faces is the development of safe and economically viable on-board hydrogen storage for fuel cell applications, especially to the transportation sector. Ammonia borane (BH3NH3), a solid state hydrogen storage material, possesses exceptionally high hydrogen content (19.6 wt%).However, a fairly high temperature is required to release all the hydrogen atoms, along with the emission of toxic borazine. Recently research interests are focusing on the improvement of H2 discharge from ammonia borane (AB) including lowering the dehydrogenation temperature and enhancing hydrogen release rate using different techniques. Till now the detailed information about the bonding characteristics of AB is not sufficient to understand details about its phases and structures. Elemental substitution of ammonia borane produces metal amidoboranes. Introduction of metal atoms to the ammonia borane structure may alter the bonding characteristics. Lithium amidoborane is synthesized by ball milling of ammonia borane and lithium hydride. High pressure study of molecular crystal provides unique insight into the intermolecular bonding forces and phase stability. During this dissertation, Raman spectroscopic study of lithium amidoborane has been carried out at high pressure in a diamond anvil cell. It has been identified that there is no dihydrogen bond in the lithium amidoborane structure, whereas dihydrogen bond is the characteristic bond of the parent compound ammonia borane. It has also been identified that the B-H bond becomes weaker, whereas B-N and N-H bonds become stronger than those in the parent compound ammonia borane. At high pressure up to 15 GPa, Raman spectroscopic study indicates two phase transformations of lithium amidoborane, whereas synchrotron X-ray diffraction data indicates only one phase transformation of this material. Pressure and temperature has a significant effect on the structural stability of ammonia borane. This dissertation explored the phase transformation behavior of ammonia borane at high pressure and low temperature using in situ Raman spectroscopy. The P-T phase boundary between the tetragonal (I4mm) and orthorhombic (Pmn21) phases of ammonia borane has been determined. The transition has a positive Clapeyron slope which indicates the transition is of exothermic in nature. Influence of nanoconfinemment on the I4mm to Pmn21 phase transition of ammonia borane was also investigated. Mesoporus silica scaffolds SBA-15 with pore size of ~8 nm and MCM-41 with pore size of 2.1-2.7 nm, were used to nanoconfine ammonia borane. During cooling down, the I4mm to Pmn21 phase transition was not observed in MCM-41 nanoconfined ammonia borane, whereas the SBA-15 nanocondfined ammonia borane shows the phase transition at ~195 K. Four new phases of ammonia borane were also identified at high pressure up to 15 GPa and low temperature down to 90 K.

Time course of haemodynamic, respiratory and inflammatory disturbances induced by experimental acute pulmonary polystyrene microembolism

Background and objective The time course of cardiopulmonary alterations after pulmonary embolism has not been clearly demonstrated and nor has the role of systemic inflammation on the pathogenesis of the disease. This study aimed to evaluate over 12 h the effects of pulmonary embolism caused by polystyrene microspheres on the haemodynamics, lung mechanics and gas exchange and on interleukin-6 production. Methods Ten large white pigs (weight 35-42 kg) had arterial and pulmonary catheters inserted and pulmonary embolism was induced in five pigs by injection of polystyrene microspheres (diameter similar to 300 mu mol l(-1)) until a value of pulmonary mean arterial pressure of twice the baseline was obtained. Five other animals received only saline. Haemodynamic and respiratory data and pressure-volume curves of the respiratory system were collected. A bronchoscopy was performed before and 12 h after embolism, when the animals were euthanized. Results The embolism group developed hypoxaemia that was not corrected with high oxygen fractions, as well as higher values of dead space, airway resistance and lower respiratory compliance levels. Acute haemodynamic alterations included pulmonary arterial hypertension with preserved systemic arterial pressure and cardiac index. These derangements persisted until the end of the experiments. The plasma interleukin-6 concentrations were similar in both groups; however, an increase in core temperature and a nonsignificant higher concentration of bronchoalveolar lavage proteins were found in the embolism group. Conclusion Acute pulmonary embolism induced by polystyrene microspheres in pigs produces a 12-h lasting hypoxaemia and a high dead space associated with high airway resistance and low compliance. There were no plasma systemic markers of inflammation, but a higher central temperature and a trend towards higher bronchoalveolar lavage proteins were found. Eur J Anaesthesiol 27:67-76 (C) 2010 European Society of Anaesthesiology.

Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

Nucleation and growth of metamorphic minerals in contact aureoles

THESIS ABSTRACT Nucleation and growth of metamorphic minerals are the consequence of changing P-T-X-conditions. The thesis presented here focuses on processes governing nucleation and growth of minerals in contact metamorphic environments using a combination of geochemical analytics (chemical-, isotope-, and trace element composition), statistical treatments of spatial data, and numerical models. It is shown, that a combination of textural modeling and stable isotope analysis allows a distinction between several possible reaction paths for olivine growth in a siliceous dolomite contact aureole. It is suggested that olivine forms directly from dolomite and quartz. The formation of olivine from this metastable reaction implies metamorphic crystallization far from equilibrium. As a major consequence, the spatial distribution of metamorphic mineral assemblages in a contact aureole cannot be interpreted as a proxy for the temporal evolution of a single rock specimen, because each rock undergoes a different reaction path, depending on temperature, heating rate, and fluid-infiltration rate. A detailed calcite-dolomite thermometry study was initiated on multiple scales ranging from aureole scale to the size of individual crystals. Quantitative forward models were developed to evaluate the effect of growth zoning, volume diffusion and the formation of submicroscopic exsolution lamellae (<1 µm) on the measured Mg-distribution in individual calcite crystals and compare the modeling results to field data. This study concludes that Mg-distributions in calcite grains of the Ubehebe Peak contact aureole are the consequence of rapid crystal growth in combination with diffusion and exsolution. The crystallization history of a rock is recorded in the chemical composition, the size and the distribution of its minerals. Near the Cima Uzza summit, located in the southern Adamello massif (Italy), contact metamorphic brucite bearing dolomite marbles are exposed as xenoliths surrounded by mafic intrusive rocks. Brucite is formed retrograde pseudomorphing spherical periclase crystals. Crystal size distributions (CSD's) of brucite pseudomorphs are presented for two profiles and combined with geochemistry data and petrological information. Textural analyses are combined with geochemistry data in a qualitative model that describes the formation periclase. As a major outcome, this expands the potential use of CSD's to systems of mineral formation driven by fluid-infiltration. RESUME DE LA THESE La nucléation et la croissance des minéraux métamorphiques sont la conséquence de changements des conditions de pression, température et composition chimique du système (PT-X). Cette thèse s'intéresse aux processus gouvernant la nucléation et la croissance des minéraux au cours d'un épisode de métamorphisme de contact, en utilisant la géochimie analytique (composition chimique, isotopique et en éléments traces), le traitement statistique des données spatiales et la modélisation numérique. Il est montré que la combinaison d'un modèle textural avec des analyses en isotopes stables permet de distinguer plusieurs chemins de réactions possibles conduisant à la croissance de l'olivine dans une auréole de contact riche en Silice et dolomite. Il est suggéré que l'olivine se forme directement à partir de la dolomie et du quartz. Cette réaction métastable de formation de l'olivine implique une cristallisation métamorphique loin de l'équilibre. La principale conséquence est que la distribution spatiale des assemblages de minéraux métamorphiques dans une auréole de contact ne peut pas être considérée comme un témoin de l'évolution temporelle d'un type de roche donné, puisque chaque type de roche suit différents chemins de réactions, en fonction de la température, la vitesse de réchauffement et le taux d'infiltration du fluide. Une étude thermométrique calcite-dolomite détaillée a été réalisée à diverses échelles, depuis l'échelle de l'auréole de contact jusqu'à l'échelle du cristal. Des modèles numériques quantitatifs ont été développés pour évaluer l'effet des zonations de croissance, de la diffusion volumique et de la formation de lamelles d'exsolution submicroscopiques (<1µm) sur la distribution du magnésium mesuré dans des cristaux de calcite individuels. Les résultats de ce modèle ont été comparés ä des échantillons naturels. Cette étude montre que la distribution du Mg dans les grains de calcite de l'auréole de contact de l'Ubehebe Peak (USA) résulte d'une croissance cristalline rapide, associée aux processus de diffusion et d'exsolution. L'histoire de cristallisation d'une roche est enregistrée dans la composition chimique, la taille et la distribution de ses minéraux. Près du sommet Cima Uzza situé au sud du massif d'Adamello (Italie), des marbres dolomitiques à brucite du métamorphisme de contact forment des xénolithes dans une intrusion mafique. La brucite constitue des pseudomorphes rétrogrades du périclase. Les distributions de taille des cristaux (CSD) des pseudomorphes de brucite sont présentées pour deux profiles et sont combinées aux données géochimiques et pétrologiques. Les analyses textorales sont combinées aux données géochimiques dans un modèle qualitatif qui décrit la formation du périclase. Ceci élargit l'utilisation potentielle de la C5D aux systèmes de formation de minéraux controlés par les infiltrations fluides. THESIS ABSTRACT (GENERAL PUBLIC) Rock textures are essentially the result of a complex interaction of nucleation, growth and deformation as a function of changing physical conditions such as pressure and temperature. Igneous and metamorphic textures are especially attractive to study the different mechanisms of texture formation since most of the parameters like pressure-temperature-paths are quite well known for a variety of geological settings. The fact that textures are supposed to record the crystallization history of a rock traditionally allowed them to be used for geothermobarometry or dating. During the last decades the focus of metamorphic petrology changed from a static point of view, i.e. the representation of a texture as one single point in the petrogenetic grid towards a more dynamic view, where multiple metamorphic processes govern the texture formation, including non-equilibrium processes. This thesis tries to advance our understanding on the processes governing nucleation and growth of minerals in contact metamorphic environments and their dynamic interplay by using a combination of geochemical analyses (chemical-, isotope-, and trace element composition), statistical treatments of spatial data and numerical models. In a first part the thesis describes the formation of metamorphic olivine porphyroblast in the Ubehebe Peak contact aureole (USA). It is shown that not the commonly assumed succession of equilibrium reactions along a T-t-path formed the textures present in the rocks today, but rather the presence of a meta-stable reaction is responsible for forming the olivine porphyroblast. Consequently, the spatial distribution of metamorphic minerals within a contact aureole can no longer be regarded as a proxy for the temporal evolution of a single rock sample. Metamorphic peak temperatures for samples of the Ubehebe Peak contact aureole were determined using calcite-dolomite. This geothermometer is based on the temperature-dependent exchange of Mg between calcite and dolomite. The purpose of the second part of this thesis was to explain the interfering systematic scatter of measured Mg-content on different scales and thus to clarify the interpretation of metamorphic temperatures recorded in carbonates. Numerical quantitative forward models are used to evaluate the effect of several processes on the distribution of magnesium in individual calcite crystals and the modeling results were then compared to measured field. Information about the crystallization history is not only recorded in the chemical composition of grains, like isotope composition or mineral zoning. Crystal size distributions (CSD's) provide essential information about the complex interaction of nucleation and growth of minerals. CSD's of brucite pseudomorphs formed retrograde after periclase of the southern Adamello massif (Italy) are presented. A combination of the textural 3D-information with geochemistry data is then used to evaluate reaction kinetics and to constrain the actual reaction mechanism for the formation of periclase. The reaction is shown to be the consequence of the infiltration of a limited amount of a fluid phase at high temperatures. The composition of this fluid phase is in large disequilibrium with the rest of the rock resulting in very fast reaction rates. RESUME DE LA THESE POUR LE GRAND PUBLIC: La texture d'une roche résulte de l'interaction complexe entre les processus de nucléation, croissance et déformation, en fonction des variations de conditions physiques telles que la pression et la température. Les textures ignées et métamorphiques présentent un intérêt particulier pour l'étude des différents mécanismes à l'origine de ces textures, puisque la plupart des paramètres comme les chemin pression-température sont relativement bien contraints dans la plupart des environnements géologiques. Le fait que les textures soient supposées enregistrer l'histoire de cristallisation des roches permet leur utilisation pour la datation et la géothermobarométrie. Durant les dernières décennies, la recherche en pétrologie métamorphique a évolué depuis une visualisation statique, c'est-à-dire qu'une texture donnée correspondait à un point unique de la grille pétrogénétique, jusqu'à une visualisation plus dynamique, où les multiples processus métamorphiques qui gouvernent 1a formation d'une texture incluent des processus hors équilibre. Cette thèse a pour but d'améliorer les connaissances actuelles sur les processus gouvernant la nucléation et la croissance des minéraux lors d'épisodes de métamorphisme de contact et l'interaction dynamique existant entre nucléation et croissance. Pour cela, les analyses géochimiques (compositions chimiques en éléments majeurs et traces et composition isotopique), le traitement statistique des données spatiales et la modélisation numérique ont été combinés. Dans la première partie, cette thèse décrit la formation de porphyroblastes d'olivine métamorphique dans l'auréole de contact de l'Ubehebe Peak (USA). Il est montré que la succession généralement admise des réactions d'équilibre le long d'un chemin T-t ne peut pas expliquer les textures présentes dans les roches aujourd'hui. Cette thèse montre qu'il s'agirait plutôt d'une réaction métastable qui soit responsable de la formation des porphyroblastes d'olivine. En conséquence, la distribution spatiale des minéraux métamorphiques dans l'auréole de contact ne peut plus être interprétée comme le témoin de l'évolution temporelle d'un échantillon unique de roche. Les pics de température des échantillons de l'auréole de contact de l'Ubehebe Peak ont été déterminés grâce au géothermomètre calcite-dolomite. Celui-ci est basé sur l'échange du magnésium entre la calcite et la dolomite, qui est fonction de la température. Le but de la deuxième partie de cette thèse est d'expliquer la dispersion systématique de la composition en magnésium à différentes échelles, et ainsi d'améliorer l'interprétation des températures du métamorphisme enregistrées dans les carbonates. Des modèles numériques quantitatifs ont permis d'évaluer le rôle de différents processus sur la distribution du magnésium dans des cristaux de calcite individuels. Les résultats des modèles ont été comparés aux échantillons naturels. La composition chimique des grains, comme la composition isotopique ou la zonation minérale, n'est pas le seul témoin de l'histoire de la cristallisation. La distribution de la taille des cristaux (CSD) fournit des informations essentielles sur les interactions entre nucléation et croissance des minéraux. La CSD des pseudomorphes de brucite retrograde formés après le périclase dans le sud du massif Adamello (Italie) est présentée dans la troisième partie. La combinaison entre les données textorales en trois dimensions et les données géochimiques a permis d'évaluer les cinétiques de réaction et de contraindre les mécanismes conduisant à la formation du périclase. Cette réaction est présentée comme étant la conséquence de l'infiltration d'une quantité limitée d'une phase fluide à haute température. La composition de cette phase fluide est en grand déséquilibre avec le reste de la roche, ce qui permet des cinétiques de réactions très rapides.

Totally implantable robot to treat chronic atrial fibrillation

Chronic atrial fibrillation affects millions of people worldwide. Its surgical treatment often fails to restore the transport function of the atrium. This study first introduces the concept of an atrial assist device (AAD) to restore the pump function of the atrium. The AAD is developed to be totally implantable in the human body with a transcutaneous energy transfer system to recharge the implanted battery. The ADD consists of a motorless pump based on artificial muscle technology, positioned on the external surface of the atrium to compress it and restore its muscular activity. A bench model reproduces the function of a fibrillating atrium to assess the circulatory support that this pump can provide. Atripump (Nanopowers SA, Switzerland) is a dome-shaped silicone-coated nitinol actuator 5 mm high, sutured on the external surface of the atrium. A pacemaker-like control unit drives the actuator that compresses the atrium, providing the mechanical support to the blood circulation. Electrical characteristics: the system is composed of one actuator that needs a minimal tension of 15 V and has a maximum current of 1.5 A with a 50% duty cycle. The implantable rechargeable battery is made of a cell having the following specifications: nominal tension of a cell: 4.1 V, tension after 90% of discharge: 3.5 V, nominal capacity of a cell: 163 mA h. The bench model consists of an open circuit made of latex bladder 60 mm in diameter filled with water. The bladder is connected to a vertically positioned tube that is filled to different levels, reproducing changes in cardiac preload. The Atripump is placed on the outer surface of the bladder. Pressure, volume and temperature changes were recorded. The contraction rate was 1 Hz with a power supply of 12 V, 400 mA for 200 ms. Preload ranged from 15 to 21 cm H(2)O. Maximal silicone membrane temperature was 55 degrees C and maximal temperature of the liquid environment was 35 degrees C. The pump produced a maximal work of 16 x 10(-3) J. Maximal volume pumped was 492 ml min(-1). This artificial muscle pump is compact, follows the Starling law and reproduces the hemodynamic performances of a normal atrium. It could represent a new tool to restore the atrial kick in persistent atrial fibrillation.

Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Effect of high hydrostatic pressure on the barrier properties of polyamide-6 films

Little is known about the barrier properties of polymer films during high pressure processing of prepackaged foods. In order to learn more about this, we examined the influence of high hydrostatic pressure on the permeation of raspberry ketone (dissolved in ethanol/water) through polyamide-6 films at temperatures between 20 and 60ºC. Permeation was lowered by increasing pressure at all temperatures. At 23°C, the increasing pressure sequence 0.1, 50, 100, 150, and 200 MPa correlated with the decreasing permeation coefficients P/(10(9) cm² s-1) of 6.2, 3.8, 3.0, 2.2, and 1.6. Analysis of the permeation kinetics indicated that this effect was due to a reduced diffusion coefficient. Pressure and temperature acted antagonistically to each other. The decrease in permeation at 200 MPa was compensated for by a temperature increase of 20ºC. After release of pressure, the former permeation coefficients were recovered, which suggests that this `pressure effect' is reversible. Taken together, our data revealed no detrimental effects of high hydrostatic pressure on the barrier properties of polymer films.

Molecular dynamics calculation of mean square displacement in alkali metals and rare gas solids and comparison with lattice dynamics

Molec ul ar dynamics calculations of the mean sq ua re displacement have been carried out for the alkali metals Na, K and Cs and for an fcc nearest neighbour Lennard-Jones model applicable to rare gas solids. The computations for the alkalis were done for several temperatures for temperature vol ume a swell as for the the ze r 0 pressure ze ro zero pressure volume corresponding to each temperature. In the fcc case, results were obtained for a wide range of both the temperature and density. Lattice dynamics calculations of the harmonic and the lowe s t order anharmonic (cubic and quartic) contributions to the mean square displacement were performed for the same potential models as in the molecular dynamics calculations. The Brillouin zone sums arising in the harmonic and the quartic terms were computed for very large numbers of points in q-space, and were extrapolated to obtain results ful converged with respect to the number of points in the Brillouin zone.An excellent agreement between the lattice dynamics results was observed molecular dynamics and in the case of all the alkali metals, e~ept for the zero pressure case of CSt where the difference is about 15 % near the melting temperature. It was concluded that for the alkalis, the lowest order perturbation theory works well even at temperat ures close to the melting temperat ure. For the fcc nearest neighbour model it was found that the number of particles (256) used for the molecular dynamics calculations, produces a result which is somewhere between 10 and 20 % smaller than the value converged with respect to the number of particles. However, the general temperature dependence of the mean square displacement is the same in molecular dynamics and lattice dynamics for all temperatures at the highest densities examined, while at higher volumes and high temperatures the results diverge. This indicates the importance of the higher order (eg. ~* ) perturbation theory contributions in these cases.