Impact response of polyethylene nanocomposites

The quasi-static and dynamic behaviour of Linear Low Density Polyethylene (LLDPE) and two LLDPE nanocomposites were studied. Nanocomposites consisting of LLDPE filled with 1% carbon black and 0.5% nanoclay fillers, by weight, were considered. Under quasi-static tensile loading, an improvement in the energy absorbing capability was achieved by adding 1% carbon black fillers. However, during quasi-static puncture and dynamic impact loading, the advantage provided by the fillers was lost. Thermal softening due to adiabatic heating under high strain rate deformation and difference s in the state of stress are considered as reasons for this reduction. © 2011 Published by Elsevier Ltd.

On the comparative efficiency of trawls made of cotton, polyethylene and combination of both the materials

The merits and demerits of cotton, polyethylene and combination of the two materials ascertained on the basis of cost, wear and tear, maintenance, total catch and qualitative analysis of the catch are discussed by making comparative fishing experiments with the three trawl gears made of these materials. The study can be concluded with a suggestion for switching over to polyethylene twisted monofilaments for better, in case of bottom trawls without in any way adversely affecting the catch of shrimps and at the same time for enhanced fish catch. Even though the combination net is found to be equal in efficiency as the polyethylene net this idea cannot be conveniently adopted from the point of view of economy.

Comparative efficiency of trawls made of nylon, polyethylene monofilament and tape twines

Results of comparative fishing operations conducted with three nets of identical design made of nylon, twisted polyethylene monofilament and high density polyethylene (HDPE) tape twines are presented in this communication. Since the tape net recorded the highest prawn and fish catch, monofilament and nylon following in order, it can be recommended to the fishing industry as one of the cheapest and effective fishing materials evolved for trawl fabrication.

Tensile strength properties of polyethylene netting twines under exposure to out-door and artificial UV radiation

Photodegradation of three types of polyethylene twines namely, polyethylene fibrillated tape twine, polyethylene flat tape twine and polyethylene monofilament twines were studied by exposing them to sunlight and artificial UV radiation. The percentage residual strength varied in the samples, the monofilament with the highest residual strength followed by fibrillated tape twine and flat tape twine. A plot of the difference between the breaking strengths of the fibrillated tape twine and the mono filament twines against any given period of exposure exhibited a linear relationship

The high strain rate response of Ultra High Molecular-weight Polyethylene: From fibre to laminate

The effect of strain rate upon the uniaxial response of Ultra High Molecular-weight Polyethylene (UHMWPE) fibres, yarns and laminates of lay-up [0/90]48 has been measured in both the 0/90 and ±45 configurations. The tensile strength of the matrix-dominated ±45 laminate is two orders of magnitude less than that of the fibre-dominated 0/90 laminate, and is more sensitive to strain rate. A piezoelectric force sensor device was developed to obtain the high strain rate data, and this achieved a rise time of less than 1 μs. It is found that the failure strength (and failure strain) of the yarn is almost insensitive to strain rate within the range (10 -1-103 s-1). At low strain rates (below 10 -1 s-1), creep of the yarn dominates and the failure strain increases with diminishing strain rate. The tensile strength of the dry yarn exceeds that of the laminate by about 20%. Tests on single fibres exceed the strength of the yarn by 20%. © 2013 Elsevier Ltd. All rights reserved.

Collapse of a composite beam made from ultra high molecular-weight polyethylene fibres

Hot-pressed laminates with a [0/90]48 lay-up, consisting of 83% by volume of ultra high molecular-weight polyethylene (UHMWPE) fibres, and 17% by volume of polyurethane (PU) matrix, were cut into cantilever beams and subjected to transverse end-loading. The collapse mechanisms were observed both visually and by X-ray scans. Short beams deform elastically and collapse plastically in longitudinal shear, with a shear strength comparable to that observed in double notch, interlaminar shear tests. In contrast, long cantilever beams deform in bending and collapse via a plastic hinge at the built-in end of the beam. The plastic hinge is formed by two wedge-shaped microbuckle zones that grow in size and in intensity with increasing hinge rotation. This new mode of microbuckling under macroscopic bending involves both elastic bending and shearing of the plies, and plastic shear of the interface between each ply. The double-wedge pattern contrasts with the more usual parallel-sided plastic microbuckle that occurs in uniaxial compression. Finite element simulations and analytical models give additional insight into the dominant material and geometric parameters that dictate the collapse response of the UHMWPE composite beam in bending. Detailed comparisons between the observed and predicted collapse responses are used in order to construct a constitutive model for laminated UHMWPE composites. © 2013 Elsevier Ltd.