Use of SECM to study the electrochemical behavior of DIN 1.4575 superferritic stainless steel aged at 475 degrees C

In order to lower the excessive costs of metallic prosthesis materia Is alternatives to Ti and Ti alloys have been searched. in this study, the corrosion resistance of the DIN 1.4575 superferritic stainless steel, either solution annealed or solution annealed and aged at 475 degrees C for periods varying from 100 to 1080 h, was investigated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization methods in Hanks` solution. The solution annealed and the aged for 1080 h samples were also tested using scanning electrochemical microscopy (SECM) in a 0.1 mol/L NaCl solution at 25 degrees C. The EIS results showed that the corrosion resistance of the DIN 1.4575 steel decreases with heat treatment time at 475 degrees C probably due to alpha prime formation. Besides the diminution of the overall impedance values, the low frequency limit of the Nyquist diagrams show a progressive change from an almost capacitive response to a resistive behavior as the heat treatment time increases. Pitting corrosion resistance also decreased with aging time at 475 degrees C.

Teor crítico de cloretos para iniciação da corrosão do aço no betão: influência do estado de superfície da armadura

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química e Biológica - Processos Químicos

Electrochemical and analytical investigation of passive films formed on stainless steels in alkaline media

Passive films were grown in potentiodynamic mode, by cyclic voltammetry on AISI 316 and AISI 304 stainless steels. The composition of these films was investigated by X-ray photoelectron spectroscopy (XPS). The electrochemical behaviour and the chemical composition of the passive films formed by cyclic voltammetry were compared to those of films grown under natural conditions (by immersion at open circuit potential, OCP) in alkaline solutions simulating concrete. The study included the effect of pH of the electrolyte and the effect of the presence of chloride ions. The XPS results revealed important changes in the passive film composition, which becomes enriched in chromium and depleted in magnetite as the pH decreases. On the other hand, the presence of chlorides promotes a more oxidised passive layer. The XPS results also showed relevant differences on the composition of the oxide layers for the films formed under cyclic voltammetry and/or under OCP.

Paperikoneen kuivatusosan olosuhteiden vaikutus viiranjohtotelojen vaipan materiaalin ja pinnoitteen valintaan korroosiovaurion ehkäisemiseksi

Diplomityön tavoitteena on löytää UPM Kymin paperikone 8:n ensimmäisen kuivatusryhmän johtoteloihin kulumis- ja korroosiokestävämpi materiaali ja pinnoite vallitsevaan olosuhteeseen. Teloihin muodostuu pistemäistä korroosiota ja korroosioalue on paikallinen. Korroosiota syntyy kuivatusviiran alueella, jossa ei ole paperirainaa. Työssä suoritetaan kuivatusosan olosuhdemittauksia ja tutkitaan niiden vaikutuksia korroosion muodostumiseen. Suoritettavat olosuhdemittaukset ovat huuvan ilmatase, paineen 0-taso sekä lämpötilat ja kosteudet eri huuvan osissa. Savukaasumittauksen avulla tutkitaan huuvan ilmankiertoa ensimmäisen kuivatusryhmän viiranjohtotelojen läheisyydessä. Kuivatusviiran ilmanläpäisymittauksen avulla saadaan tietoa viiran ilmanläpäisykyvystä. Hypoteesina viiran tukkeutuminen johtuu pölyävästä kuivaus-prosessista ja kosteudesta. SEM/EDS-alkuainemittauksen avulla pystytään analysoimaan korrosiivisia alkuaineita niin korroosioalueella kuin ympäristössä. Työn tutkimuksen perusteella korroosion muodostuminen aiheutuu tukkeutuneen viiran muodostamasta happipitoisuuseroalueesta. Viiran saostumat sisältävät korrosiivisia kemikaaleja, kuten kloridia, rikkiä ja mangaania. Nämä kiihdyttävät korroosiota happipuutosalueella. Huuvan olosuhdemittauksien perusteella huuvan paineen 0-taso on vino. Savukaasu- ja kosteusmittauksien avulla huomattiin kostean ilman jäävän telojen läheisyyteen. Työssä kehitettiin paineilmapuhdistin viiran reuna-alueen puhdistamiseen. Kaavattaviin telapositioihin valittiin kobolttikromiseostettu volframikarbidipinnoite PTFE -fluoripolymeeritiivistyksellä. Muihin telapositioihin valittiin ETFE –fluori-polymeeripinnoite korroosion ehkäisemiseksi. Pinnoitteiden ja paineilmapuhdistimen avulla telojen käyttöaika nousee nykyisestä kahdesta vuodesta tavoiteltuun 10 vuoteen.

New material for orthopedic implants: Electrochemical study of nickel free P558 stainless steel in minimum essential medium

Nickel, a component of stainless steels (SS) applied in orthopedic implants may cause allergic processes in human tissues P558 nickel free SS was studied to verify its viability as a substitute for stainless steel containing nickel Its performance is compared to ISO 5832-9 and F138 most used nowadays grades in implants fabrications, in minimum essential medium. MEM, at 37 degrees C. Potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and ""in vitro"" cytotoxicity were used as techniques. From the electrochemical point of view P558 SS is comparable to ISO 5832-9 SS in MEM It remains passivated until the transpassivation potential, above which generalized corrosion occurs F138 presents pitting corrosion at 370 mV/SCE. The cytotoxicity results showed that P558. ISO 5832-9 and F138 do not present cytotoxic character Therefore, these results suggest that P558 SS can be applied in orthopedic implants (C) 2010 Elsevier BV All rights reserved

Comparative electrochemical study of 5832-9 stainless steel at different media of biological interest

The electrochemical behavior of ISO 5832-9 stainless steel at 37 degrees C in 0.9% NaCl, Ringer Lactate and minimum essential medium (MEM) has been studied, using linear voltammetry, and surface analysis by SEM and EDS. Mechanical and toxicity tests were made. ISO 5832-9 is passivated at corrosion potential (E) and it does not present pitting corrosion on the media studied from to 50 in V above the transpassivation potential (Ei). SEM and EDS analysis have shown that the sample previously immersed in MEM presents a diffirent behavior at 50 in V above El: the manganese oxide inclusions are absent in the surface. E. values and passivation current density values j(pass) changed according to the following. E(corr, RL) < E(corr,NaCl) < E(corr, MEM) and J (MEM) << j(RL) congruent to j(NaCl) The stainless steel was characterized as non toxic in the cytotoxicity assay

Contribuição ao estudo da inibição da corrosão do aço comum por borato, em soluções diluídas

Este trabalho teve por objetivo determinar a ação inibidora do íon borato na corrosão do aço-carbono, em soluções aquosas aproximadamente neutras, arejadas e desarejadas, na presença ou não de ions cloreto, à temperatura ambiente. Através do traçado de curvas de polarização potenciostáticas, de experimentos cronopotenciométricos e cronogalvanométricos, com ou sem riscagem do corpo de prova, e do comportamento do aço comum em ensaios de imersão a longo prazo, concluiu-se que o ion borato possui uma ação inibidora sobre a corrosão do aço, desde que o potencial não seja muito elevado. Observou-se também que o aço sofre corrosão por pites em soluções de borato, mesmo na ausência de íons agressivos e que os pites ocorrem em potenciais tanto mais baixos quanto mais diluídas forem as soluções de borato. Para soluções contendo 1000 ppm de bórax ou mais, o potencial de pite, determinado por técnicas cronopotenciométricas, está acima do potencial de corrosão. Para soluções com concentrações iguais ou superiores a 5000 ppm de bórax, não foi detectada corrosão por pites na faixa de potencial estudada, isto é, desde o potencial de evolução de H2 até o potencial de evolução de 02. A adição de 100 ppm de NaCl à solução contendo 2500 ppm de bórax reduz o potencial de pite de aço comum, em relação ao seu valor na ausência de íon cloreto.

Stability of cp-Ti and Ti-6Al-4V alloy for dental implants as a function of saliva pH - an electrochemical study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Electrochemical behaviour of heat-treated Al-Zn-Mg alloys in chloride solutions containing sulphate

The electrochemical corrosion and passivation of Al-5Zn-1.7Mg-0.23Cu-0.053Nb alloys, submitted to different heat treatments (cold-rolled, annealed, quenched and aged, and quenched in two steps and aged), in sulphate-containing chloride solutions, has been studied by means of cyclic polarization, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), and X-ray photoelectron spectroscopy (XPS). The cyclic polarization curves showed that sulphate addition to the chloride solution produced a poor reproducible shift of the breakdown potential to more positive potentials. The repassivation potentials, much more reproducible, and practically separating the passive from the pitting potential region, were slightly displaced in the negative direction with that addition. When the alloys were potentiodynamically polarized in the passive potential region, sulphate was incorporated in the oxide film, thus precluding chloride ingress. In addition, Zn depletion was favoured, whereas Mg losses were avoided. Different equivalent circuits corresponding to different alloys and potentials in the passive and pitting regions were employed to account for the electrochemical processes taking place in each condition. This work shows that sulphate makes these alloys more sensitive to corrosion, increasing the fracture properties of the surface layer and favouring the pitting attack over greater areas than chloride alone. (C) 2002 Elsevier B.V. Ltd. All rights reserved.

Electrochemical behavior of Ti-Mo alloys applied as biomaterial

Electrochemical investigation on the as-cast Ti-Mo alloys (4-20 Mo wt.%) applied as biomaterials in Na2SO4 and Ringer physiological solutions is reported. Analyses of the open-circuit potential indicated that all alloys present spontaneous passivation. SEM and cyclic voltammograms obtained in the Ringer solution showed that the samples studied do not present pitting corrosion at potentials up to 8 V (SCE), indicating high corrosion resistance. Open-circuit potential profiles of the anodic oxides growth in both solutions show that the presence of chloride ions during the anodization does not influence the oxides' chemical stability, and also clearly indicate that adding Mo to pure Ti improves the stability of the anodic oxides. All these results suggest Ti-Mo alloys promissory to be applied as biomaterials. (c) 2008 Elsevier Ltd. All rights reserved.

Estudo do mecanismo de corrosão por pites em água do mar de aços inoxidáveis supermartensíticos microligados com Nb e Ti

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Morphological analysis of pits formed on Al 2024-T3 in chloride aqueous solution

It has been used a new image analysis method, based on segmentation by shape parameters, for pits morphology examination from Al 2024 aluminum-copper alloy in chloride aqueous solution. Corrosion behavior of this alloys in naturally aerated 3.5% NaCl solution has been investigated through open circuit potential measurements. Afterwards, pits have been characterized by image analysis taking density and size measurements right from corroded surfaces. Morphological investigation has been conducted for profiles, cut orthogonally from mean surface planes, and observed through light microscopy. Image analysis data could demonstrate that pits are wider than deep, evoluting for conical, quasi-conical or irregular shapes. Most pits have presented a quasi-conical morphology, but the wider ones have evoluted to an irregular shape influenced by sub-surface microstructure. Image analysis based on shape segmentation could enhance the differences on morphological behavior. (C) 2004 Elsevier B.V. All rights reserved.

An image analysis study of pit formation on Ti-6Al-4V

Metallographic techniques and digital image processing have been used to investigate heat-treated Ti-6Al-4V pitting corrosion, often used as aircraft components. LM and SEM metallography of 'as received', annealed (heating up to 800 degreesC/30 min and cooling furnace) and aged (heating up to 900 degreesC/30 min, quenching in water, heating up to 540 degreesC/240 min and again water-quenched) microstructures reveal pitting sites at primary and secondary alpha/beta interfaces. Microstructural arrangements influence and corrosive environment association on pit morphology could be demonstrated by digital image analysis and results statistical treatment. (C) 2002 Elsevier B.V. B.V. All rights reserved.

On the development of the electrochemical potentiokinetic method

The development of electrochemical potentiokinetic methods as applied to the testing of metals and alloys is followed from its early phases up to its latest advances relating to intergranular corrosion, SCC and pitting corrosion tests of stainless steels and special alloys and to the examination of their structure and properties. In assessing the susceptibility to intergranular and pitting corrosion by potentiokinetic polarization tests, the polarization curves which apply to the bulk of the alloy grains (the matrix) must be distinguished from those pertaining to grain boundaries. Cyclic polarization measurements such as the electrochemical potentiokinetic reactivation (EPR) test make it possible to derive the alloy's susceptibility to intergranular, pitting and crevice corrosion from characteristic potentials and other quantities determined in the 'double loop' test. EPR is rapid and responds to the combined effects of a number of factors that influence the properties of materials. The electrochemical p otentiokinetic tests are sensitive enough to detect structural changes in heat treated materials ranging far beyond the stainless steels alone, and can be used for non-destructive testing aimed at elucidating the properties and behavior of materials. © 2001 Elsevier Science Ltd. All rights reserved.

Caracterização morfológica da corrosão por pite da liga AL2024 em soluções contendo cloretos e molibdatos

A very new method application for digital image processing and analysis to classify shape and evaluate size and morphology parameters of pit corrosion is used in this paper. This method seems to be very effective to analysis surfaces with low or high degree of pitting formation. Pits formed on 2024 alloy surface by chloride and by chloride + molibdate anions have similar mean area, are found to be widther than deeper and exhibit predominantly conical or near-conical and irregular geometries.