Influence of interface on radiation effects of crystalline polymer - radiation effects on polyamide-1010 containing BMI

Aimed at saving the radiation dose required to crosslinking the polyamid-1010, BMI/PA1010 systems containing different amounts of difunctional crosslinking agent N,N'-bis-maleimide-4,4'-biphenyl methane (BMI) were prepared and the structure changes at the crystallographic and supermolecular levels before and after irradiation were studied by using WAXD, SAXS, and DSC techniques. It was found that by incorporation of BMI the microcrystal size L-100 is lowered due to the formation of hydrogen bond between the carbonyl oxygen of BMI and the amide hydrogen of PA1010 in the hydrogen bonded plane, and the overall crystallinity W-c is also decreased. The presence of BMI causes the crystal lamella thickness d(c) to decrease and greatly thickens the transition zone d(tr) between the crystalline and amorphous regions. As for the irradiated specimen, the maximum increments in the L-100 and W-c against dose curves decrease with BMI content, and the interception point D-i, at which the L-100 and W-c curves intercept their respective horizontal line of L-100/L-100(0) and W-c/W-c(0)=1, shift to lower dose with an increase in BMI concentration. In addition. the mechanism of the radiation chemical reactions in the three different phases under the action of BMI are discussed with special focus on the interface region. (C) 1999 Published by Elsevier Science Ltd. All rights reserved.

Blends of polyamide1010 with unmodified and maleic-anhydride-grafted high-impact polystyrene

The crystallization behaviors, dynamic mechanical properties, tensile, and morphology features of polyamide1010 (PA1010) blends with the high-impact polystyrene (HIPS) were examined at a wide composition range. Both unmodified and maleicanhydride-(MA)-grafted HIPS (HIPS-g-MA) were used. It was found that the domain size of HIPS-g-MA was much smaller than that of HIPS at the same compositions in the blends. The mechanical performances of PA1010-HIPS-g-MA blends were enhanced much more than that of PA1010-HIPS blends. The crystallization temperature of PA1010 shifted towards higher temperature as HIPS-g-MA increased from 20 to 50% in the blends. For the blends with a dispersed PA phase (less than or equal to 35 wt %), the T-c of PA1010 shifted towards lower temperature, from 178 to 83 degrees C. An additional transition was detected at a temperature located between the T-g's of PA1010 and PS. It was associated with the interphase relaxation peak. Its intensity increased with increasing content of PA1010, and the maximum occurred at the composition of PA1010-HIPS-g-MA 80/20. (C) 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 857-865, 1999.

Studies on the interfacial adhesion between functionalized polypropylene and polyamide 1010

The interface behavior of polyamide 1010 (PA1010) and polypropylene (PP) was studied. In order to improve their interfacial adhesion, functional PP was prepared by means of grafting glycidyl methacrylate (GMA) on PP main chains and used instead of plain PP. Several technological characterizations were performed here on their interfaces. ESCA was used to confirm that some kind of reaction occurred between end groups of PA1010 and epoxy species of PP-g-GMA. The peel test was adopted to measure interfacial adhesion. It was found that the fracture energy of interfaces between PA1010 and PP-g-GMA was dramatically increased with the content of GMA. Their interfaces were observed as being blurred by using SEM and TEM and a crack that could be seen in the case of the interfaces of the PA1010 and the plain PP disappeared.

尼龙1010分别与未接枝和接枝马来酸酐的高抗冲聚苯乙烯的共混体系研究

研究了尼龙1010(PA1010)与高抗冲聚苯乙烯(HIPS)及马来酸酐官能化的HIPS(HIPS-g-MA)间的相互作用，利用DSC,DMA,SEM及拉伸测试等方法研究了不同组成比的共混物PA1010/HIPS与PA1010/HIPS-g-MA的结晶、玻璃化转变、形态及力学性能．结果表明HIPS与PA1010虽然结构相差甚远，但两者之间仍存在着一定的相互作用；而HIPS-s-MA可使PA1010的低温熔融峰变小，当HIPS-g-MA的含量≤50%时，随着其含量的增加，共混物中PA1010的结晶温度升高；当含量＞50%时，PA1010发生分级结晶行为，其结晶温度由原来的178℃降至83℃，同时HIPS-g-MA与PA1010间的相互作用变大，DMA谱上有明显的新的松驰峰．PA1010/HIPS-g-MA共混体系的拉伸性能要优于相同组成的PA1010/HIPS体系．以上现象主要是...

The characterization of the interfacial reaction in polyamide 1010 poly(propylene)-graft-(glycidylmethacrylate) blends

Binary blends of polyamide 1010/poly(propylene) and polyamide 1010 (PA1010)/poly(propylene)-graft-(glycidyl methacrylate) (PP-g-GMA) were prepared. The epoxy groups in PP-g-GMA react with the amino end-groups in PA1010, thus a PA1010-graft-PP copolymer is formed and acts as a compatibilizer between PA1010 and PP-g-GMA. The reaction was confirmed by electron spectroscopy for chemical analysis (ESCA) and attenuated total reflection (ATR)-FTIR spectroscopic analysis, and also evaluated by the stability of the suspension obtained by dissolving the blends in formic acid and by the morphologies of the blends.

Effect of the fold surface of the lamellae on the behavior of the trapped radicals in irradiated polyamide-1010

Two types of macromolecular free radicals -CH2CONHCHCH2- (a) and -CH2C=O (b) trapped in irradiated Polyamide-1010 (PA1010) and PA1010 filled with neodymium oxide (Nd2O3) were characterized by an ESR approach. It was found out that a was mainly trapped in the fold surface of the lamellae and b in the amorphous phase. This result suggested that trapped radicals mainly existed in the noncrystalline phases. The effect of the fold surface area of the lamellae on the behavior of the trapped radicals are discussed in this article. Whether for the specimens with similar crystallinities but different crystallite sizes or for those with the same concentration of neodymium oxide but different crystallinities, radical a exists dominantly in a specimen with a larger fold surface area of the lamellae. Under a certain circumstance, radical a can transform into radical b for a specimen with a larger fold surface area of the lamellae. It means that the fold surface area of the lamellae plays an important role in the transformation of radical a to b. (C) 1998 John Wiley & Sons, Inc.

Morphological studies of polyamide 1010/polypropylene blends

Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the morphology of blends of PA1010 and polypropylene (PP) compatibilized with polypropylene grafted with glycidyl methacrylate (PP-g-GMA). It is found that the morphologies are dependent on the content of glycidyl methacrylate in PP-g-GMA and the mixing time. The size of the dispersed PP particles decreases as the content of GMA in the PP-g-GMA increases for binary blends of PA1010 and PP-g-GMA. Similar results are obtained for changing the mixing time. Ternary blends of PA1010, PP, and PP-g-GMA indicate that morphologies depend on the content of glycidyl metyacrylate in the PP-g-GMA and the miscibility of PP and PP-g-GMA. By changing the content of GMA in PP-g-GMA, it was possible to introduce significant changes of morphology. A matrix removal TEM method is used to investigate the interfacial structure of PA1010/PP blends containing PP-g-GMA as a compatibilizer. This technique shows the reaction product between PA1010 and PP-g-GMA to be located at interface as a surrounding layer around domain particles. SEM observation on the interface shows that the adhesion between PA1010 and pure PP is very weak and their interface boundary is sharp. For the samples of PA1010 and PP-g-GMA, it was found that the interface was not so obvious, and the reaction between PA1010 and PP-g-GMA strengthens the interface significantly. (C) 1997 Elsevier Science Ltd.

Heterogeneous nucleation effects of neodymium oxide on polyamide-1010

In this paper microcrystalline structures of polyamide-1010 (PA1010) mixed with neodymium oxide (Nd2O3) were studied by Wide Angle X-ray Diffraction (WAXD) and Small Angle X-ray Scattering (SAXS). Crystallization behavior was investigated by DSC. The transition and relaxation of macromolecules in the crystalline phase were explored by Differential Scanning Calorimetry (DSC). It was revealed that neodymium oxide plays an important role in PA1010 crystallization as a heterogeneous nucleating agent. It can improve the crystallization rate, reduce crystallite size and introduce crystal imperfections. The microcrystalline structure was imposed by the addition of Nd2O3 However, the heterogeneous nucleation effect obviously does not exert its influence on the transition and relaxation of macromolecules in the crystalline phase.

Crystallization behavior of poly(propylene)/polyamide 1010 blends using poly(propylene)-graft glycidyl methacrylate as compatibilizer

Polyamide 1010/poly(propylene) (PA1010/PP) blends were investigated with and without the addition of poly(propylene)-graft-glycidyl methacrylate (PP-g-GMA). The effect of the compatibilizer on the thermal properties and crystallization behavior was determined by differential scanning calorimetry and wide-angle X-ray diffraction. From the results it is found that the crystallization of PA 1010 is significantly affected by the presence of PP-g-GMA. PP/PA 1010 (75/25) blends containing higher amounts of PP-g-GMA show concurrent crystallization at the crystallization temperature of PP. Isothermal crystallization kinetics also were performed in order to investigate the influence of the compatibilized process on the nucleation and growth mechanism. In the PP/PA 1010 (25/75) blends, concurrent crystallization behavior was not observed, even though the amount of PPg-GMA was high.

ESR approach to free radicals trapped in irradiated polyamide-1010

Two types of macromolecular free radicals similar to CH2CONH(C) over dotHCH(2) similar to (a) and similar to CH2(C) over dot = O (b) trapped in irradiated polyamide-1010 (PA1010) and PA1010 filled with neodymium oxide (Nd2O3) were characterized by an ESR approach. It is found that (a) is prevailingly trapped in the fold surface of the lamellae and (b) in the amorphous phase. This result suggests that trapped radicals mainly exist in the non-crystalline phases. The effect of the fold surface area of the lamellae on the behavior of the trapped radicals is discussed in this paper. Whether for the specimens with similar crystallinities, but different crystallite sizes, or for those with the same concentration of neodymium oxide, but different crystallinities, radical (a) exists dominantly in the specimen with a larger fold surface area of the lamellae. Under certain circumstances, radical (a) can transform into radical (b), obviously for a specimen with a larger fold surface area of the lamellae. It means that the fold surface area of the lamellae plays an important role in the transformation of radical (a) to (b). (C) 1997 Elsevier Science Ltd.

Radiation-induced crystallization of polyamide-1010 containing heterogeneous nuclei

Radiation-induced crystallization of polyamide-1010 (PA1010) or nylon-1010 containing heterogeneous nuclei (neodymium oxide, Nd2O3) is discussed in this paper by Wide Angle X-ray Diffraction (WAXD) and Differential Scanning Calorimetry (DSC). The results show that at low dosage the crystallinities of the irradiated specimens increase, while crystallite size (L(hkl)) decreases, indicating that some new crystallites are produced in the course of irradiation. The new centers were brought about in the fold surface of the lamellae. Copyright (C) 1997 Elsevier Science Ltd

Exploration of post radiation effects on polyamide-1010

Irradiated polyamide-1010 (PA1010) with and without heat treatment after gamma-ray irradiation was compared by wide angle x-ray diffraction (WAXD), differential scanning calorimeter (DSC) and the determination of gel fractions. The results indicate that post radiation effects due to post radiation crosslinking and scissions affect physical properties. Post radiation effects restrain the formation and perfection of the planes (010), and make the crystals imperfect. Post radiation effects change the crystalline structures of polyamide-1010.

Influence of the fold surface of the lamellae on radiation effects - Research on irradiated polyamide-1010 containing heterogeneous nuclei

Irradiated polyamide-1010 (PA1010) and PA1010 containing 0.5% (wt) heterogeneous nuclei were studied by ESR, WAXD, DSC and the determination of gel fractions. The fold surface of the lamellae plays an important role in the effects of radiation on crystalline PA1010. The results show that the direct radiation effects on both samples vary, while after being heated to 220 degrees C, the final radiation effects are identical, regardless of the difference in the amount of the fold surface of the lamellae. The post-radiation effects result predominantly from the fold surface.

Crystal structure of the blend of polyamide 1010 with a bismaleimide by WAXD and SAXS

The blend polyamide 1010/N,N'-(diphenylmethane-4,4'-diyl)bismaleimide (PA1010/ BMI) has been investigated by means of WAXD and SAXS. The results obtained with the help of the Ruland, variance and 1D EDCF analysis showed that the degree of crystallinity (W-c,W-x), crystallite size (L(hikl)), long period (L) and thickness of average crystal lamellae (d) decrease with BMI content. Experimental and calculated density values (rho(c)) are in good agreement. Addition of BMT to PA1010 causes an increase in structural distortion. The results from SAXS analysis also supported that a crystalline amorphous interphase exists in the lamellae of semicrystalline polymers, so that a three-phase model instead of the traditional two-phase model should be used.

Small angle X-ray scattering study of structural parameters of the aggregated state in polyamide 1010+BMI

The structural parameters of the aggregated state in the polyamide PA1010 and N,N'-bismaleimide-4,4'-diphenyl methane (BMI) system were computed by means of the desmearing intensity from SAXS and using the concept of the distance distribution function. The results revealed that the parameters Q, I(0), l(c) and L decreased with the increase BMI component, whereas O-s increased. The particle dimension Z for different BMI contents was less than 13.2 nm, and the maximum value of the distance distribution function P(Z) was found to be in the range Z = 6.5-7.0 nm.