Thermalhydraulic behavior of electrically heated rod during a critical heat flux transient

In nuclear reactors, the occurrence of critical heat flux leads to fuel rod overheating with clad fusion and radioactive products leakage. To predict the effects of such phenomenon, experiments are performed using electrically heated rods to simulate operational and accidental conditions of nuclear fuel rods. In the present work, it is performed a theoretical analysis of the drying and rewetting front propagation during a critical heat flux experiment, starting with the application of an electrical power step from steady state condition. After the occurrence of critical heat flux, the drying front propagation is predicted. After a few seconds, a power cut is considered and the rewetting front behavior is analytically observed. Studies performed with various values of coolant mass flow rate show that this variable has more influence on the drying front velocity than on the rewetting one.

Isostatic pressing of UO₂ in high temperature metals /

The hot isostatic pressing process has been applied at temperatures up to 1500°C for the fabrication of high temperature fuel rods composed of UO₂ clad in columbium and UO₂ in iron-aluminum type alloy. The fused UO₂ powder apparently becomes quite plastic at temperatures above 1200°C and can be isostatically compacted at 1500°C to 98% of its theoretical density. Columbian tubes particularly lend themselves to the fabrication of fuel rods by simultaneously compacting and cladding UO₂ powders in the tubes, but the cast iron-aluminum type alloy that was used was unsatisfactory because of its brittleness.

Ignition conditions for inertial confinement fusion targets with a nuclear spin-polarized DT fuel

The nuclear fusion cross-section is modified when the spins of the interacting nuclei are polarized. In the case of deuterium?tritium it has been theoretically predicted that the nuclear fusion cross-section could be increased by a factor d = 1.5 if all the nuclei were polarized. In inertial confinement fusion this would result in a modification of the required ignition conditions. Using numerical simulations it is found that the required hot-spot temperature and areal density can both be reduced by about 15% for a fully polarized nuclear fuel. Moreover, numerical simulations of a directly driven capsule show that the required laser power and energy to achieve a high gain scale as d-0.6 and d-0.4 respectively, while the maximum achievable energy gain scales as d0.9.

Overview of the Spanish Fuel Cycle: Technical Tours Organized by Spanish young Generation in Nuclear.

Spanish Young Generation in Nuclear (Jóvenes Nucleares, JJNN) is a non-profrt organization that depends on the Spanish Nuclear Society (Sociedad Nuclear Española, SNE).Since one of rts main goals is to spread the knowledge about nuclear power,severa! technical tours to facilities wrth an importan!role in the nuclear fuel cycle have been organized for the purpose ofleaming about the different stages of the Spanish tuel cycle. Spanish Young Generation in Nuclear had the opportunity to visit ENUSA Fuel Assembly Factory in Juzbado (Salamanca, Spain), Where it could be understood the front-end cycle which involves the uranium supply and storage, design and manufacturing of fuel bundles for European nuclear power plants. Alterwards, due to the tour of Almaraz NPP (PWR) and Santa María de Garoña NPP (BWR), rt could be comprehended how to obtain energy from this fuel in two different types of reactors.Furthermore,in these two plants, the facilities related to the back-end cycle could be toured. lt was possible to watch the Spent FuelPools, where the fuel bundles are stored under water until their activity is reduced enough to transport them to an Individual Temporary Storage Facility orto the Centralized Temporary Storage. Finally, a technical tour to ENSA Heavy Components Factory (ENSA) was accomplished, Where it could be experienced at first hand how different Nuclear Steam Supply System (NSSS) components and other nuclear elements, such as racks or shipping and storage casks for spent nuclear fuel, are manulactured. All these perlonned technical tours were a complete success thanks to a generous care and know-how of the wor1

Sistema de simulación de escenarios de ciclos avanzados de combustible nuclear en transición = Simulation system for advanced fuel cycle transition scenarios

El estudio de los ciclos del combustible nuclear requieren de herramientas computacionales o "códigos" versátiles para dar respuestas al problema multicriterio de evaluar los actuales ciclos o las capacidades de las diferentes estrategias y escenarios con potencial de desarrollo en a nivel nacional, regional o mundial. Por otra parte, la introducción de nuevas tecnologías para reactores y procesos industriales hace que los códigos existentes requieran nuevas capacidades para evaluar la transición del estado actual del ciclo del combustible hacia otros más avanzados y sostenibles. Brevemente, esta tesis se centra en dar respuesta a las principales preguntas, en términos económicos y de recursos, al análisis de escenarios de ciclos de combustible, en particular, para el análisis de los diferentes escenarios del ciclo del combustible de relativa importancia para España y Europa. Para alcanzar este objetivo ha sido necesaria la actualización y el desarrollo de nuevas capacidades del código TR_EVOL (Transition Evolution code). Este trabajo ha sido desarrollado en el Programa de Innovación Nuclear del CIEMAT desde el año 2010. Esta tesis se divide en 6 capítulos. El primer capítulo ofrece una visión general del ciclo de combustible nuclear, sus principales etapas y los diferentes tipos utilizados en la actualidad o en desarrollo para el futuro. Además, se describen las fuentes de material nuclear que podrían ser utilizadas como combustible (uranio y otros). También se puntualizan brevemente una serie de herramientas desarrolladas para el estudio de estos ciclos de combustible nuclear. El capítulo 2 está dirigido a dar una idea básica acerca de los costes involucrados en la generación de electricidad mediante energía nuclear. Aquí se presentan una clasificación de estos costos y sus estimaciones, obtenidas en la bibliografía, y que han sido evaluadas y utilizadas en esta tesis. Se ha incluido también una breve descripción del principal indicador económico utilizado en esta tesis, el “coste nivelado de la electricidad”. El capítulo 3 se centra en la descripción del código de simulación desarrollado para el estudio del ciclo del combustible nuclear, TR_EVOL, que ha sido diseñado para evaluar diferentes opciones de ciclos de combustibles. En particular, pueden ser evaluados las diversos reactores con, posiblemente, diferentes tipos de combustibles y sus instalaciones del ciclo asociadas. El módulo de evaluaciones económica de TR_EVOL ofrece el coste nivelado de la electricidad haciendo uso de las cuatro fuentes principales de información económica y de la salida del balance de masas obtenido de la simulación del ciclo en TR_EVOL. Por otra parte, la estimación de las incertidumbres en los costes también puede ser efectuada por el código. Se ha efectuado un proceso de comprobación cruzada de las funcionalidades del código y se descrine en el Capítulo 4. El proceso se ha aplicado en cuatro etapas de acuerdo con las características más importantes de TR_EVOL, balance de masas, composición isotópica y análisis económico. Así, la primera etapa ha consistido en el balance masas del ciclo de combustible nuclear actual de España. La segunda etapa se ha centrado en la comprobación de la composición isotópica del flujo de masas mediante el la simulación del ciclo del combustible definido en el proyecto CP-ESFR UE. Las dos últimas etapas han tenido como objetivo validar el módulo económico. De este modo, en la tercera etapa han sido evaluados los tres principales costes (financieros, operación y mantenimiento y de combustible) y comparados con los obtenidos por el proyecto ARCAS, omitiendo los costes del fin del ciclo o Back-end, los que han sido evaluado solo en la cuarta etapa, haciendo uso de costes unitarios y parámetros obtenidos a partir de la bibliografía. En el capítulo 5 se analizan dos grupos de opciones del ciclo del combustible nuclear de relevante importancia, en términos económicos y de recursos, para España y Europa. Para el caso español, se han simulado dos grupos de escenarios del ciclo del combustible, incluyendo estrategias de reproceso y extensión de vida de los reactores. Este análisis se ha centrado en explorar las ventajas y desventajas de reprocesado de combustible irradiado en un país con una “relativa” pequeña cantidad de reactores nucleares. Para el grupo de Europa se han tratado cuatro escenarios, incluyendo opciones de transmutación. Los escenarios incluyen los reactores actuales utilizando la tecnología reactor de agua ligera y ciclo abierto, un reemplazo total de los reactores actuales con reactores rápidos que queman combustible U-Pu MOX y dos escenarios del ciclo del combustible con transmutación de actínidos minoritarios en una parte de los reactores rápidos o en sistemas impulsados por aceleradores dedicados a transmutación. Finalmente, el capítulo 6 da las principales conclusiones obtenidas de esta tesis y los trabajos futuros previstos en el campo del análisis de ciclos de combustible nuclear. ABSTRACT The study of the nuclear fuel cycle requires versatile computational tools or “codes” to provide answers to the multicriteria problem of assessing current nuclear fuel cycles or the capabilities of different strategies and scenarios with potential development in a country, region or at world level. Moreover, the introduction of new technologies for reactors and industrial processes makes the existing codes to require new capabilities to assess the transition from current status of the fuel cycle to the more advanced and sustainable ones. Briefly, this thesis is focused in providing answers to the main questions about resources and economics in fuel cycle scenario analyses, in particular for the analysis of different fuel cycle scenarios with relative importance for Spain and Europe. The upgrade and development of new capabilities of the TR_EVOL code (Transition Evolution code) has been necessary to achieve this goal. This work has been developed in the Nuclear Innovation Program at CIEMAT since year 2010. This thesis is divided in 6 chapters. The first one gives an overview of the nuclear fuel cycle, its main stages and types currently used or in development for the future. Besides the sources of nuclear material that could be used as fuel (uranium and others) are also viewed here. A number of tools developed for the study of these nuclear fuel cycles are also briefly described in this chapter. Chapter 2 is aimed to give a basic idea about the cost involved in the electricity generation by means of the nuclear energy. The main classification of these costs and their estimations given by bibliography, which have been evaluated in this thesis, are presented. A brief description of the Levelized Cost of Electricity, the principal economic indicator used in this thesis, has been also included. Chapter 3 is focused on the description of the simulation tool TR_EVOL developed for the study of the nuclear fuel cycle. TR_EVOL has been designed to evaluate different options for the fuel cycle scenario. In particular, diverse nuclear power plants, having possibly different types of fuels and the associated fuel cycle facilities can be assessed. The TR_EVOL module for economic assessments provides the Levelized Cost of Electricity making use of the TR_EVOL mass balance output and four main sources of economic information. Furthermore, uncertainties assessment can be also carried out by the code. A cross checking process of the performance of the code has been accomplished and it is shown in Chapter 4. The process has been applied in four stages according to the most important features of TR_EVOL. Thus, the first stage has involved the mass balance of the current Spanish nuclear fuel cycle. The second stage has been focused in the isotopic composition of the mass flow using the fuel cycle defined in the EU project CP-ESFR. The last two stages have been aimed to validate the economic module. In the third stage, the main three generation costs (financial cost, O&M and fuel cost) have been assessed and compared to those obtained by ARCAS project, omitting the back-end costs. This last cost has been evaluated alone in the fourth stage, making use of some unit cost and parameters obtained from the bibliography. In Chapter 5 two groups of nuclear fuel cycle options with relevant importance for Spain and Europe are analyzed in economic and resources terms. For the Spanish case, two groups of fuel cycle scenarios have been simulated including reprocessing strategies and life extension of the current reactor fleet. This analysis has been focused on exploring the advantages and disadvantages of spent fuel reprocessing in a country with relatively small amount of nuclear power plants. For the European group, four fuel cycle scenarios involving transmutation options have been addressed. Scenarios include the current fleet using Light Water Reactor technology and open fuel cycle, a full replacement of the initial fleet with Fast Reactors burning U-Pu MOX fuel and two fuel cycle scenarios with Minor Actinide transmutation in a fraction of the FR fleet or in dedicated Accelerator Driven Systems. Finally, Chapter 6 gives the main conclusions obtained from this thesis and the future work foreseen in the field of nuclear fuel cycle analysis.

The effect of nuclear radiation on ceramic reactor-fuel materials /

"June 30, 1963."

The effect of nuclear radiation on metallic fuel materials /

"September 30, 1963."

TiN-based coatings on fuel cladding tubes for advanced nuclear reactors

Titanium nitride (TiN) thin films are coated on HT-9 and MA957 fuel cladding tubes and bars to explore their mechanical strength, thermal stability, diffusion barrier properties, and thermal conductivity properties. The ultimate goal is to implement TiN as an effective diffusion barrier to prevent the inter-diffusion between the nuclear fuel and the cladding material, and thus lead to a longer lifetime of the cladding tubes. Mechanical tests including hardness and scratch tests for the samples before and after thermal cycle tests show that the films have a high hardness of 28GPa and excellent adhesion properties despite the thermal treatment. Thermal conductivity measurements demonstrate that the thin TiN films have very minimal impact on the overall thermal conductivity of the MA957 and HT-9 substrates, i.e., the thermal conductivity of the uncoated HT-9 and MA957 substrates was 26.25 and 28.44 W m-1 K-1, and that of the coated ones was 26.21 and 28.38W m-1 K-1, respectively. A preliminary Ce diffusion test on the couple of Ce/TiN/HT-9 suggests that TiN has excellent material compatibility and good diffusion barrier properties.

Reactores a tório: o futuro da energia nuclear de fissão

Dissertação para a obtenção do grau de mestre em Engenharia Electrotécnica Ramo de Energia

Experimental thermal hydraulic studies on the enhancement of safety of LWRs

The safe use of nuclear power plants (NPPs) requires a deep understanding of the functioning of physical processes and systems involved. Studies on thermal hydraulics have been carried out in various separate effects and integral test facilities at Lappeenranta University of Technology (LUT) either to ensure the functioning of safety systems of light water reactors (LWR) or to produce validation data for the computer codes used in safety analyses of NPPs. Several examples of safety studies on thermal hydraulics of the nuclear power plants are discussed. Studies are related to the physical phenomena existing in different processes in NPPs, such as rewetting of the fuel rods, emergency core cooling (ECC), natural circulation, small break loss-of-coolant accidents (SBLOCA), non-condensable gas release and transport, and passive safety systems. Studies on both VVER and advanced light water reactor (ALWR) systems are included. The set of cases include separate effects tests for understanding and modeling a single physical phenomenon, separate effects tests to study the behavior of a NPP component or a single system, and integral tests to study the behavior of the whole system. In the studies following steps can be found, not necessarily in the same study. Experimental studies as such have provided solutions to existing design problems. Experimental data have been created to validate a single model in a computer code. Validated models are used in various transient analyses of scaled facilities or NPPs. Integral test data are used to validate the computer codes as whole, to see how the implemented models work together in a code. In the final stage test results from the facilities are transferred to the NPP scale using computer codes. Some of the experiments have confirmed the expected behavior of the system or procedure to be studied; in some experiments there have been certain unexpected phenomena that have caused changes to the original design to avoid the recognized problems. This is the main motivation for experimental studies on thermal hydraulics of the NPP safety systems. Naturally the behavior of the new system designs have to be checked with experiments, but also the existing designs, if they are applied in the conditions that differ from what they were originally designed for. New procedures for existing reactors and new safety related systems have been developed for new nuclear power plant concepts. New experiments have been continuously needed.

New Type Nuclear Reactors (NETNUC) 2008-2011 Final Report

This report summarizes the work done by a consortium consisting of Lappeenranta University of Technology, Aalto University and VTT Technical Research Centre of Finland in the New Type Nuclear Reactors (NETNUC) project during 2008–2011. The project was part of the Sustainable Energy (SusEn) research programme of the Academy of Finland. A wide range of generation IV nuclear technologies were studied during the project and the research consisted of multiple tasks. This report contains short articles summarizing the results of the individual tasks. In addition, the publications produced and the persons involved in the project are listed in the appendices.