921 resultados para Municipal wastewater


Relevância:

70.00% 70.00%

Publicador:

Resumo:

Pharmaceuticals are ubiquitous in surface waters as a consequence of discharges from municipal wastewater treatment plants. However, few studies have assessed the bioavailability of pharmaceuticals to fish in natural waters. In the present study, passive samplers and rainbow trout were experimentally deployed next to three municipal wastewater treatment plants in Finland to evaluate the degree of animal exposure. Pharmaceuticals from several therapeutic classes (in total 15) were analyzed by liquid chromatography-tandem mass spectrometry in extracts of passive samplers and in bile and blood plasma of rainbow trout held at polluted sites for 10 d. Each approach indicated the highest exposure near wastewater treatment plant A and the lowest near that of plant C. Diclofenac, naproxen, and ibuprofen were found in rainbow trout, and their concentrations in bile were 10 to 400 times higher than in plasma. The phase I metabolite hydroxydiclofenac was also detected in bile. Hence, bile proved to be an excellent sample matrix for the exposure assessment of fish. Most of the monitored pharmaceuticals were found in passive samplers, implying that they may overestimate the actual exposure of fish in receiving waters. Two biomarkers, hepatic vitellogenin and cytochrome P4501A, did not reveal clear effects on fish, although a small induction of vitellogenin mRNA was observed in trout caged near wastewater treatment plants B and C.

Relevância:

70.00% 70.00%

Publicador:

Resumo:

To study the possibility of producing better water quality from municipal wastewater, a membrane bioreactor (MBR) pilot plant with flat sheet (FS) and hollow fiber (HF) membranes coupled with another pilot plant equipped with nanofiltration (NF)/reverse osmosis (RO) membranes were operated to treat municipal wastewater from the wastewater treatment plant (WWTP) Rincón de León, Alicante (Spain). This study was focused on improving the quality of the permeate obtained from the MBR process when complemented by NF or RO stages with respect to salinity, organic matter and nutrients. Furthermore, the removal efficiencies of 10 EMPs were evaluated, comparing the reductions achieved between the wastewater treatment by MBR (adsorption to sludge and biodegradation) and the later treatment using NF or RO (mainly size exclusion). The results showed that the high quality of water was obtained which is appropriate for reuse with salinity removal efficiencies higher than 97%, 96% for total organic carbon (TOC), 91% for nitrates View the MathML sourceNO3- and 99% for total phosphorous (TP). High removal efficiencies were obtained for the majority of the analyzed EMP compounds.

Relevância:

70.00% 70.00%

Publicador:

Resumo:

Human activities represent a significant burden on the global water cycle, with large and increasing demands placed on limited water resources by manufacturing, energy production and domestic water use. In addition to changing the quantity of available water resources, human activities lead to changes in water quality by introducing a large and often poorly-characterized array of chemical pollutants, which may negatively impact biodiversity in aquatic ecosystems, leading to impairment of valuable ecosystem functions and services. Domestic and industrial wastewaters represent a significant source of pollution to the aquatic environment due to inadequate or incomplete removal of chemicals introduced into waters by human activities. Currently, incomplete chemical characterization of treated wastewaters limits comprehensive risk assessment of this ubiquitous impact to water. In particular, a significant fraction of the organic chemical composition of treated industrial and domestic wastewaters remains uncharacterized at the molecular level. Efforts aimed at reducing the impacts of water pollution on aquatic ecosystems critically require knowledge of the composition of wastewaters to develop interventions capable of protecting our precious natural water resources.

The goal of this dissertation was to develop a robust, extensible and high-throughput framework for the comprehensive characterization of organic micropollutants in wastewaters by high-resolution accurate-mass mass spectrometry. High-resolution mass spectrometry provides the most powerful analytical technique available for assessing the occurrence and fate of organic pollutants in the water cycle. However, significant limitations in data processing, analysis and interpretation have limited this technique in achieving comprehensive characterization of organic pollutants occurring in natural and built environments. My work aimed to address these challenges by development of automated workflows for the structural characterization of organic pollutants in wastewater and wastewater impacted environments by high-resolution mass spectrometry, and to apply these methods in combination with novel data handling routines to conduct detailed fate studies of wastewater-derived organic micropollutants in the aquatic environment.

In Chapter 2, chemoinformatic tools were implemented along with novel non-targeted mass spectrometric analytical methods to characterize, map, and explore an environmentally-relevant “chemical space” in municipal wastewater. This was accomplished by characterizing the molecular composition of known wastewater-derived organic pollutants and substances that are prioritized as potential wastewater contaminants, using these databases to evaluate the pollutant-likeness of structures postulated for unknown organic compounds that I detected in wastewater extracts using high-resolution mass spectrometry approaches. Results showed that application of multiple computational mass spectrometric tools to structural elucidation of unknown organic pollutants arising in wastewaters improved the efficiency and veracity of screening approaches based on high-resolution mass spectrometry. Furthermore, structural similarity searching was essential for prioritizing substances sharing structural features with known organic pollutants or industrial and consumer chemicals that could enter the environment through use or disposal.

I then applied this comprehensive methodological and computational non-targeted analysis workflow to micropollutant fate analysis in domestic wastewaters (Chapter 3), surface waters impacted by water reuse activities (Chapter 4) and effluents of wastewater treatment facilities receiving wastewater from oil and gas extraction activities (Chapter 5). In Chapter 3, I showed that application of chemometric tools aided in the prioritization of non-targeted compounds arising at various stages of conventional wastewater treatment by partitioning high dimensional data into rational chemical categories based on knowledge of organic chemical fate processes, resulting in the classification of organic micropollutants based on their occurrence and/or removal during treatment. Similarly, in Chapter 4, high-resolution sampling and broad-spectrum targeted and non-targeted chemical analysis were applied to assess the occurrence and fate of organic micropollutants in a water reuse application, wherein reclaimed wastewater was applied for irrigation of turf grass. Results showed that organic micropollutant composition of surface waters receiving runoff from wastewater irrigated areas appeared to be minimally impacted by wastewater-derived organic micropollutants. Finally, Chapter 5 presents results of the comprehensive organic chemical composition of oil and gas wastewaters treated for surface water discharge. Concurrent analysis of effluent samples by complementary, broad-spectrum analytical techniques, revealed that low-levels of hydrophobic organic contaminants, but elevated concentrations of polymeric surfactants, which may effect the fate and analysis of contaminants of concern in oil and gas wastewaters.

Taken together, my work represents significant progress in the characterization of polar organic chemical pollutants associated with wastewater-impacted environments by high-resolution mass spectrometry. Application of these comprehensive methods to examine micropollutant fate processes in wastewater treatment systems, water reuse environments, and water applications in oil/gas exploration yielded new insights into the factors that influence transport, transformation, and persistence of organic micropollutants in these systems across an unprecedented breadth of chemical space.

Relevância:

70.00% 70.00%

Publicador:

Resumo:

The possibility of thermal treatment plants of municipal wastewater is an alternative solution for the final disposition of the sludge produced on small cities as Barueri, a small town of São Paulo State, Brazil. Combustion and pyrolysis of that municipal waste, occurring respectively in air and nitrogen, have been studied by thermogravimetry (TG) and differential thermal analysis (DTA). The main steps of each case were analyzed and Kissinger plots were used to estimate respective activation energies. DTG peaks are more indicated to represent the condition of maximum reaction rates than DTA peaks.

Relevância:

70.00% 70.00%

Publicador:

Resumo:

Biochemical processes by chemoautotrophs such as nitrifiers and sulfide and iron oxidizers are used extensively in wastewater treatment. The research described in this dissertation involved the study of two selected biological processes utilized in wastewater treatment mediated by chemoautotrophic bacteria: nitrification (biological removal of ammonia and nitrogen) and hydrogen sulfide (H2S) removal from odorous air using biofiltration. A municipal wastewater treatment plant (WWTP) receiving industrial dyeing discharge containing the azo dye, acid black 1 (AB1) failed to meet discharge limits, especially during the winter. Dyeing discharge mixed with domestic sewage was fed to sequencing batch reactors at 22oC and 7oC. Complete nitrification failure occurred at 7oC with more rapid nitrification failure as the dye concentration increased; slight nitrification inhibition occurred at 22oC. Dye-bearing wastewater reduced chemical oxygen demand (COD) removal at 7oC and 22oC, increased i effluent total suspended solids (TSS) at 7oC, and reduced activated sludge quality at 7oC. Decreasing AB1 loading resulted in partial nitrification recovery. Eliminating the dye-bearing discharge to the full-scale WWTP led to improved performance bringing the WWTP into regulatory compliance. BiofilterTM, a dynamic model describing the biofiltration processes for hydrogen sulfide removal from odorous air emissions, was calibrated and validated using pilot- and full-scale biofilter data. In addition, the model predicted the trend of the measured data under field conditions of changing input concentration and low effluent concentrations. The model demonstrated that increasing gas residence time and temperature and decreasing influent concentration decreases effluent concentration. Model simulations also showed that longer residence times are required to treat loading spikes. BiofilterTM was also used in the preliminary design of a full-scale biofilter for the removal of H2S from odorous air. Model simulations illustrated that plots of effluent concentration as a function of residence time or bed area were useful to characterize and design biofilters. Also, decreasing temperature significantly increased the effluent concentration. Model simulations showed that at a given temperature, a biofilter cannot reduce H2S emissions below a minimum value, no matter how large the biofilter.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Toxic chemicals can enter the marine environment through numerous routes: stormwater runoff, industrial point source discharges, municipal wastewater discharges, atmospheric deposition, accidental spills, illegal dumping, pesticide applications and agricultural practices. Once they enter a receiving system, toxicants often become bound to suspended particles and increase in density sufficiently to sink to the bottom. Sediments are one of the major repositories of contaminants in aquatic envronments. Furthermore, if they become sufficiently contaminated sediments can act as sources of toxicants to important biota. Sediment quality data are direct indicators of the health of coastal aquatic habitats. Sediment quality investigations conducted by the National Oceanic and Atmospheric Administration (NOAA) and others have indicated that toxic chemicals are found in the sediments and biota of some estuaries in South Carolina and Georgia (NOAA, 1992). This report documents the toxicity of sediments collected within five selected estuaries: Savannah River, Winyah Bay, Charleston Harbor, St. Simons Sound, and Leadenwah Creek (Figure 1). (PDF contains 292 pages)

Relevância:

60.00% 60.00%

Publicador:

Resumo:

A aplicabilidade de um método selecionado de medição indireta de vitelogenina (Vtg) em plasma sanguíneo de peixe, baseado na quantificação de fosfato álcali-lábil (alkali-labile phosphate-ALP) para acessar estrogenicidade em água, foi investigada na presente tese. O método foi originalmente desenvolvido para a espécie de peixe Carassius carassius (Carpa cruciana) e aplicado pela primeira vez na espécie Oreochromis niloticus (Tilápia do Nilo) no presente estudo. Com o objetivo de acessar a sensibilidade do método, em uma primeira etapa da investigação foram realizados estudos laboratoriais com soluções estoques de 17-ethinylestradiol (EE2), 17-estradiol (E2), e estrona (E1). Os efeitos destes hormônios foram investigados com base tanto na concentração quanto na carga, utilizando-se para tanto, unidades experimentais com volumes distintos (2 L e 130 L). Após a validação do método de ALP, a estrogenicidade foi avaliada nas seguintes águas contaminadas: (i) afluente e efluente de uma grande estação de tratamento de esgotos convencional (ETE) e de uma estação descentralizada de tratamento de esgoto de pequeno porte (Ecossistema Engenheirado-DEE); (ii) água superficial (SW) e água subterrânea (GW) coletadas em uma área de brejo contaminada com gasolina; (iii) água de uma lagoa urbana (LRF) da cidade do Rio de Janeiro, com alta densidade populacional e descarte clandestino de esgoto. Na segunda etapa foram analisados em microalgas os efeitos (outros que não disrupção endócrina) causados pelos hormônios EE2, E2 e E1. Os hormônios foram testados individualmente e em misturas, em culturas individuais e combinada (S+) das espécies de microalgas unicelulares P. subcapitata e D. subspicatus. Com base nos níveis de ALP para a espécie de peixe e no EC50 para as espécies de algas, os resultados mostraram que o EE2 e o E2 causaram disrupção endócrina superior e foram mais tóxicos do que o E1 para peixes e microalgas respectivamente. Quando em misturas (E+) de concentrações equivalentes (EE2:E2:E1), os estrogênios resultaram em efeito aditivo para as espécies O. niloticus e P. subcapitata, e menos que aditivo para D. subspicatus e cultivo misto de algas (S+). Culturas contendo ambas as espécies de algas (S+) por um longo período de exposição (96 h) resultaram na atenuação dos efeitos tóxicos causados pela exposição, tanto individual (EE2, E2 ou E1), quanto na mistura (E+) dos estrogênios, medidos em termos de EC50 (T0h 0,07; 0,09; 0,18; e 0,06 g mL-1; e T96h 1,29; 1,87; 5,58; e 4,61 g mL-1, respectivamente). O DEE apresentou uma maior eficiência na remoção dos disrutores endócrinos do que a ETE convencional. Foi detectada estrogenicidade em amostras da LRF, e de água SW e GW em área brejosa contaminada com gasolina. Os resultados dos ensaios sugerem que as interações (efeitos aditivos ou menos que aditivo) causadas pela mistura dos estrogênios assim como, as interações entre as espécies de algas afetaram o resultado final dos ensaios ecotoxicológicos. Um fator raramente abordado em estudos ecotoxicológicos que foi destacado na presente tese refere-se à importância de considerar não somente a concentração e a dosagem, mas também a carga aplicada e o volume das unidades experimentais. Devido à boa sensibilidade do O. niloticus quando exposto às concentrações relativamente baixas dos estrogênios, a combinação do método de ALP com os biomarcadores auxiliares (particularmente MN) pode ser um protocolo adequado para a detecção de estogenicidade e genotoxicidade respectivamente em diferentes ambiente aquáticos contaminados, como parte de um programa de monitoramento ambiental

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Lake Victoria shoreline in Jinja Municipality has four urban wetlands of Kirinya West/Loco, Kirinya East/Walukuba, Masese and Budumbuli which have undergone major changes during the past fifty years due to increased human activities. Amongst these activities is the continuous inflow of agricultural run-off, industrial and municipal wastewater. A significant increase in nutrient loads of Nitrogen and Phosphorus from the catchment area continues to enhance eutrophication of Lake Victoria. Pollution from point sources (Industrial plants and NWSC Kirinya final maturation pond) into Jinja’s urban wetlands were therefore studied using a simplified material flux analysis methodology to identify the active elements and estimate the pollution loads due to Nitrogen, Phosphorus, Carbon (nutrients), Chromium, Copper, Lead, Nickel and Manganese metals.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Total alkaline phosphatase activity (APA) and soluble reactive phosphorus (SRP) concentrations were measured in municipal wastewater, and a shallow Chinese freshwater lake receiving it. Activities of Dissolved alkaline phosphatase ( ADAP) in overlying and interstitial water were also analyzed monthly at three sites for several years. The lake was enriched with SRP and alkaline phosphatase by discharge of the wastewater, indicating that the inclusion of APA for estimating water pollution was reasonable. Annual data showed that APA in coarser fraction was significantly higher at the site receiving more wastewaters, both in surface and overlying water, suggesting that resuspension of enzyme most likely occurred in the basin heavily discharged. ADAP was an order of magnitude higher in the wastewater than those in lake waters, and was generally higher in interstitial water, a feature more striking at the site receiving more discharges. Besides, it was irrespectively inhibited by Na2WO4, L-cysteine and EDTA-Na, but stimulated by Cu2+, Zn2+, CTAB and Triton X-100 in interstitial, overlying and surface waters. This similarity of responding patterns to the stressors indicated an analogy between dissolved alkaline phosphatase in water column and that in interstitial water, supporting the hypothesis that the polluted sediments act as source of dissolved alkaline phosphatase in eutrophic lakes.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil, na Área de Especialização de Hidráulica

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Le présent projet vise à documenter la nécessité d’augmenter notre connaissance de la présence des contaminants organiques tels que les médicaments dans l’environnement et d’évaluer leur devenir environnemental. On a étudié la présence de composés pharmaceutiques dans différents échantillons d'eau. On a focalisé nos efforts spécialement sur les échantillons d'eau de l'usine d'épuration de la Ville de Montréal et ses effluents, les eaux de surface avoisinantes et l’eau du robinet dans la région de Montréal. Pour ce faire, on a tout d’abord développé deux méthodes analytiques automatisées basées sur la chromatographie liquide avec extraction en phase solide (SPE) couplée à la chromatographie liquide couplée à la spectrométrie de masse en tandem (LC-MS/MS). On a également étudié les performances des trois techniques d'ionisation à pression atmosphérique (API), pour ensuite les utiliser dans la méthode analytique développée. On a démontré que l'ionisation par électronébulisation (ESI) est une méthode d'ionisation plus efficace pour l'analyse des contaminants pharmaceutiques dans des échantillons de matrices très complexes comme les eaux usées. Une première méthode analytique SPE couplée à la LC-MS/MS a été développée et validée pour l'étude des échantillons complexes provenant de l'usine d'épuration de la Ville de Montréal et des eaux de surface près de l'usine. Cinq médicaments de prescription ont été étudiés: le bézafibrate (un régulateur de lipides), le cyclophosphamide et le méthotrexate (deux agents anticancéreux), l'orlistat (un agent anti-obésité) et l’énalapril (utilisé dans le traitement de l'hypertension). La plupart de ces drogues sont excrétées par le corps humain et rejetées dans les eaux usées domestiques en faisant par la suite leur chemin vers les usines municipales de traitement des eaux usées. On a pu démontrer qu'il y a un faible taux d’élimination à l'usine d'épuration pour le bézafibrate et l'énalapril. Ces deux composés ont aussi été détectés dans les eaux de surface sur un site à proximité immédiate de la décharge de l’effluent de la station d'épuration. i En observant la nécessité de l'amélioration des limites de détection de la première méthode analytique, une deuxième méthode a été développée. Pour la deuxième méthode, un total de 14 contaminants organiques, incluant trois agents anti-infectieux (clarithromycin, sulfaméthoxazole et triméthoprime), un anticonvulsant (carbamazépine) et son produit de dégradation (10,11-dihydrocarbamazépine), l'agent antihypertensif (enalapril), deux antinéoplastiques utilisés en chimiothérapie (cyclophosphamide et méthotrexate), des herbicides (atrazine, cyanazine, et simazine) et deux produits de transformation de l’atrazine (deséthylatrazine et déisopropylatrazine) ainsi qu’un agent antiseptique (triclocarban). Ces produits ont été quantifiés dans les eaux de surface ainsi que dans l’eau du robinet. L'amélioration des limites de détection pour cette méthode a été possible grâce à la charge d'un volume d'échantillon supérieur à celui utilisé dans la première méthode (10 mL vs 1 mL). D'autres techniques de confirmation, telles que les spectres des ions produits utilisant une pente d’énergie de collision inverse dans un spectromètre de masse à triple quadripôle et la mesure des masses exactes par spectrométrie de masse à temps d’envol, ont été explorées. L'utilisation d'un analyseur de masse à temps d’envol a permis la confirmation de 6 des 14 analytes. Finalement, étant donné leur haute toxicité et pour évaluer leur persistance et leur transformation au niveau du traitement des eaux potables, la cinétique d'oxydation du cyclophosphamide et de méthotrexate avec l'ozone moléculaire et des radicaux OH a été étudiée. Les constantes de dégradation avec l'ozone moléculaire ont été calculées et la qualité de l'eau après traitement a pu être évaluée. Le rendement du processus d'ozonation a été amélioré pour la cyclophosphamide dans les eaux naturelles, en raison de la combinaison de réactions directes et indirectes. Cette étude a montré que l'ozone est très efficace pour oxyder le méthotrexate mais que le cyclophosphamide serait trop lent à s’oxyder pour un traitement efficace aux conditions usuelles de traitement de l’eau potable.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Cette thèse a été codirigée par le Dr. Florent Chazarenc

Relevância:

60.00% 60.00%

Publicador:

Resumo:

La production de biodiésel par des microalgues est intéressante à plusieurs niveaux. Dans le premier chapitre, un éventail de pour et contres concernant l’utilisation de microalgues pour la production de biocarburant sont ici révisés. La culture d’algues peut s'effectuer en utilisant des terres non-arables, de l’eau non-potable et des nutriments de base. De plus, la biomasse produite par les algues est considérablement plus importante que celle de plantes vasculaires. Plusieurs espèces on le contenu lipidique en forme de triacylglycérols (TAGs), qui peut correspondre jusqu'à 30% - 40% du poids sec de la biomasse. Ces proportions sont considérablement plus élevées que celui des huiles contenues dans les graines actuellement utilisées pour le biodiésel de première génération. Par contre, une production pratique et peu couteuse de biocarburant par des microalgues requiert de surpasser plusieurs obstacles. Ceci inclut le développement de systèmes de culture efficace à faible coût, de techniques de récupération requérant peu d’énergie, et de méthodes d’extraction et de conversion de l’huile non-dommageables pour l’environnement et peu couteuses. Le deuxième chapitre explore l'une des questions importantes soulevées dans le premier chapitre: la sélection d'une souche pour la culture. Une collection de souches de microalgues d'eau douce indigène au Québec a été établi et examiné au niveau de la diversité physiologique. Cette collection est composée de cent souches, que apparaissaient très hétérogènes en terme de croissance lorsque mises en culture à 10±2 °C ou 22±2 °C sur un effluent secondaire d’une usine municipale de traitement des eaux usées (EU), défini comme milieu Bold's Basal Medium (BBM). Des diagrammes de dispersion ont été utilisés pour étudier la diversité physiologique au sein de la collection, montrant plusieurs résultats intéressants. Il y avait une dispersion appréciable dans les taux de croissance selon les différents types de milieux et indépendamment de la température. De manière intéressante, en considérant que tous les isolats avaient initialement été enrichis sur milieu BBM, la distribution était plutôt symétrique autour de la ligne d’iso-croissance, suggérant que l’enrichissement sur BBM n’a pas semblé biaiser la croissance des souches sur ce milieu par rapport aux EU. Également, considérant que les isolats avaient d’abord été enrichis à 22°C, il est assez surprenant que la distribution de taux de croissance spécifiques soit aussi symétrique autour de la ligne d’iso-croissance, avec grossièrement des nombres égaux d’isolats de part et d’autre. Ainsi, l’enrichissement à 22°C ne semble pas biaiser les cellules vers une croissance à cette température plutôt que vers 10°C. Les diagrammes de dispersion obtenus lorsque le pourcentage en lipides de cultures sur BBM ont été comparées à des cultures ayant poussé sur EU soit à 10°C ou 22°C rendent évident que la production de lipides est favorisée par la culture sur EU aux deux températures, et que la production lipidique ne semble pas particulièrement plus favorisée par l’une ou l’autre de ces températures. Lorsque la collection a été examinée pour y déceler des différences avec le site d’échantillonnage, une analyse statistique a montré grossièrement que le même degré de diversité physiologique était retrouvé dans les échantillons des deux différents sites. Le troisième chapitre a poursuivi l'évaluation de la culture d'algues au Québec. L’utilisation de déchets industriels riches en nutriments minéraux et en sources de carbone pour augmenter la biomasse finale en microalgues et le produit lipidique à faible coût est une stratégie importante pour rendre viable la technologie des biocarburants par les algues. Par l’utilisation de souches de la collection de microalgues de l’Université de Montréal, ce rapport montre pour la première fois que des souches de microalgues peuvent pousser en présence de xylose, la source de carbone majoritairement retrouvée dans les eaux usées provenant des usines de pâte et papier, avec une hausse du taux de croissance de 2,8 fois par rapport à la croissance photoautotrophe, atteignant jusqu’à µ=1,1/jour. En présence de glycérol, les taux de croissance atteignaient des valeurs aussi élevées que µ=1,52/jour. La production lipidique augmentait jusqu’à 370% en présence de glycérol et 180% avec le xylose pour la souche LB1H10, démontrant que cette souche est appropriée pour le développement ultérieur de biocarburants en culture mixotrophe. L'ajout de xylose en cultures d'algues a montré certains effets inattendus. Le quatrième chapitre de ce travail a porté à comprendre ces effets sur la croissance des microalgues et la production de lipides. Quatre souches sauvages indigènes ont été obersvées quotidiennement, avant et après l’ajout de xylose, par cytométrie en flux. Avec quelques souches de Chlorella, l’ajout de xylose induisait une hausse rapide de l’accumulation de lipide (jusqu’à 3,3 fois) pendant les premières six à douze heures. Aux temps subséquents, les cellules montraient une diminution du contenu en chlorophylle, de leur taille et de leur nombre. Par contre, l’unique membre de la famille des Scenedesmaceae avait la capacité de profiter de la présence de cette source de carbone sous culture mixotrophe ou hétérotrophe sans effet négatif apparent. Ces résultats suggèrent que le xylose puisse être utilisé avant la récolte afin de stimuler l’augmentation du contenu lipidique de la culture d’algues, soit en système de culture continu ou à deux étapes, permettant la biorestauration des eaux usées provenant de l’industrie des pâtes et papiers. Le cinquième chapitre aborde une autre déché industriel important: le dioxyde de carbone et les gaz à effet de serre. Plus de la moitié du dioxyde de carbone qui est émis dans l'atmosphère chaque jour est dégagé par un processus stationnaire, soit pour la production d’électricité ou pour la fabrication industrielle. La libération de CO2 par ces sources pourrait être atténuée grâce à la biorestauration avec microalgues, une matière première putative pour les biocarburants. Néanmoins, toutes les cheminées dégagent un gaz différent, et la sélection des souches d'algues est vitale. Ainsi, ce travail propose l'utilisation d’un état de site particulier pour la bioprospection de souches d'algues pour être utilisé dans le processus de biorestauration. Les résultats montrent que l'utilisation d'un processus d'enrichissement simple lors de l'étape d'isolement peut sélectionner des souches qui étaient en moyenne 43,2% mieux performantes dans la production de biomasse que les souches isolées par des méthodes traditionnelles. Les souches isolées dans ce travail étaient capables d'assimiler le dioxyde de carbone à un taux supérieur à la moyenne, comparées à des résultats récents de la littérature.

Relevância:

60.00% 60.00%

Publicador:

Resumo:

Nitrification is the biological oxidation of ammonium, first to nitrite and then to nitrate by two groups of aerobic, chemolithotrophic bacteria belonging to the family Nitrobacteriaceae. The biological nitrification in municipal wastewater treatment is important in those cases were ammonia removal requirement specially exist. In a trickling filter or in an activated sludge system nitrification is rate limiting and thus necessitates longer detention time. The combined carbon oxidation-nitrification processes generally have low population of nitrifiers due to a high ratio of BOD to total nitrogen in the effluent. This necessitates, separate carbon and nitrogen oxidation processes, which thus minimizes wash out ofthe nitrifiers. Therefore, a separate stage nitrification has become essential to achieve faster and efficient removal of ammonia from the wastewater. The present work deals with the development of bio reactor for nitrifying of sewage as the tertiary process so that the treated wastewater can be used for irrigation, algal culture or fish culture