WATER RESOURCES SITUATION AT PIRACICABA, CAPIVARI AND JUNDIAI WATERSHEDS USING A DYNAMIC SYSTEMS MODEL

Using a dynamic systems model specifically developed for Piracicaba, Capivari and Jundia River Water Basins (BH-PCJ) as a tool to help to analyze water resources management alternatives for policy makers and decision takers, five simulations for 50 years timeframe were performed. The model estimates water supply and demand, as well as wastewater generation from the consumers at BH-PCJ. A run was performed using mean precipitation value constant, and keeping the actual water supply and demand rates, the business as usual scenario. Under these considerations, it is expected an increment of about similar to 76% on water demand, that similar to 39% of available water volume will come from wastewater reuse, and that waste load increases to similar to 91%. Falkenmark Index will change from 1,403 m(3) person(-1) year(-1) in 2004, to 734 m(3) P(-1) year(-1) by 2054, and the Sustainability Index from 0.44 to 0.20. Another four simulations were performed by affecting the annual precipitation by 90 and 110%; considering an ecological flow equal to 30% of the mean daily flow; and keeping the same rates for all other factors except for ecological flow and household water consumption. All of them showed a tendency to a water crisis in the near future at BH-PCJ.

Aplicação de ferramentas de simulação de processos

Este trabalho foi efectuado com o propósito de interpretar, compreender e explicar algumas ferramentas de simulação de processos, em particular o Aspen Energy Analyzer (AEA), o Aspen Economic Evaluation (AEE) e o seu funcionamento integrado com o Aspen Hysys(AH). O AH é uma ferramenta de modelação de processos para a concepção de projectos de engenharia química, o AEA é uma ferramenta de modelação de redes de integração energética. O AEE integrado no AH é uma ferramenta que permite incorporar estudos económicos numa fase preliminar do desenvolvimento de um projecto de engenharia. A abordagem a este trabalho foi efectuada através do estudo de Casos. O Caso I foi baseado na resolução de um problema no AEA através da construção e optimização de uma rede de permutadores de calor. Os Casos II e III foram baseados na construção de um flowsheet de produção de Benzeno e de Cloreto de Vinil, respectivamente, e cada Caso foi dividido em dois cenários diferentes. Para o efeito foram utilizados os softwares AEA para a integração energética dos processos, o AH para construção do fluxograma do processo e o AEE para os estudos económicos dos diferentes cenários. Finalmente, os Casos IV e V dizem respeito à resolução de um problema de integração energética. O Caso IV foi baseado num problema de optimização da rede de permutadores através do aumento da sua área. Já o Caso V foi baseado na informação inicial das correntes do caso anterior e em dois cenários diferentes, nos quais foi estudada a influência dos preços das utilidades na construção da rede de permutadores. A conclusão foi que as ferramentas de modelação, particularmente o AH, o AEA e o AEE são uma mais-valia extraordinária para ajudar o utilizador na tomada de decisões em fases bastante preliminares da engenharia de processos.

A strategy to extend reactive distillation column performance under catalyst deactivation

This work addresses the effects of catalyst deactivation and investigates methods to reduce their impact on the reactive distillation columns performance. The use of variable feed quality and reboil ratio are investigated using a rigorous dynamic model developed in gPROMS and applied to an illustrative example, i.e., the olefin metathesis system, wherein 2-pentene reacts to form 2-butene and 3-hexene. Three designs and different strategies on column energy supply to tackle catalyst deactivation are investigated and the results compared.

Geração de simuladores de filas para diferentes contextos com estudo de casos para redes de computadores

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelação de torre eólica: controlo e desempenho

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Energia

DYNAMOD – A dynamic agent based modelling framework for digital businesses

Digital Businesses have become a major driver for economic growth and have seen an explosion of new startups. At the same time, it also includes mature enterprises that have become global giants in a relatively short period of time. Digital Businesses have unique characteristics that make the running and management of a Digital Business much different from traditional offline businesses. Digital businesses respond to online users who are highly interconnected and networked. This enables a rapid flow of word of mouth, at a pace far greater than ever envisioned when dealing with traditional products and services. The relatively low cost of incremental user addition has led to a variety of innovation in pricing of digital products, including various forms of free and freemium pricing models. This thesis explores the unique characteristics and complexities of Digital Businesses and its implications on the design of Digital Business Models and Revenue Models. The thesis proposes an Agent Based Modeling Framework that can be used to develop Simulation Models that simulate the complex dynamics of Digital Businesses and the user interactions between users of a digital product. Such Simulation models can be used for a variety of purposes such as simple forecasting, analysing the impact of market disturbances, analysing the impact of changes in pricing models and optimising the pricing for maximum revenue generation or a balance between growth in usage and revenue generation. These models can be developed for a mature enterprise with a large historical record of user growth rate as well as for early stage enterprises without much historical data. Through three case studies, the thesis demonstrates the applicability of the Framework and its potential applications.

Modelação, simulação e implementação de agitação acústica para aplicações em microfluídica

Tese de Doutoramento (Programa Doutoral em Engenharia Biomédica)

Höyry- ja kaasuturbiinin mallintaminen prosessisimulointiohjelmaan

Tässä diplomityössä on mallinnettu höyry- ja kaasuturbiini Balas -prosessisimulointi-ohjelmaan. Balas on Valtion Teknillisen Tutkimuskeskuksen kehittämä simulointiohjelma, erityisesti paperi- ja selluteollisuuden prosessien staattiseen simulointiin. Työn tavoitteena on kehittää simulointimallit höyry- ja kaasuturbiinille, sekä tutkia niiden toimivuutta vertaamalla simulointeja mittaus- ja mitoitustietoihin. Työssä on muodostettu matemaattiset mallit höyryturbiinille, höyryturbiinin säätövyöhykkeelle sekä höyryturbiinin off-design laskennalle. Kaasuturbiinille muodostettiin toimintakäyrät, joiden avulla tarkastellaan sen toimintaa off-design tilanteessa. Komponentit mallinnettiin diplomityövaiheessa Matlab-ympäristöön, josta ne siirretään Balasiin erillisessä työvaiheessa. Malleissa on kiinnitetty huomiota erityisesti niiden helppokäyttöisyyteen ja monipuolisuuteen. Höyryturbiinimalleja testattiin simuloimalla erään paperitehtaan yhteydessä toimivan voimalaitoksen vastapaineturbiini säätövyöhykkeineen ja vertaamalla simulointituloksia tehtaan mittaustietoihin. Kaasuturbiinimallia testattiin vertaamalla GE Power MS 7001 kaasuturbiinin mitoitustietoja vastaavilla parametreilla simuloituun tapaukseen.

Blender- ja Bullet-ohjelmiston soveltuvuus robotiikan simulointiin.

Työssä tutkittiin Blender- ja Bullet-ohjelmiston soveltuvuutta robotin dynamiikan analysointiin. Ohjelmistot ovat avoimia ohjelmistoja joten niiden käyttö oli maksutonta. Robotin osat mallinnettiin Blender-ohjelmistolla ja koottiin kokoonpanoksi asettamalla nivelet kappaleiden väleille. Kokoonpanon tiedot siirrettiin Bullet-ohjelmistoon COLLADA-tiedoston välityksellä. Bullet-ohjelmistossa robotin dynaaminen käyttäytyminen laskettiin matemaattisesti tietokoneen avulla.

MÉTODO ALTERNATIVO PARA A SÍNTESE E MECANISMO DE 2-(1,3-DITIANO-2-ILIDENO)-ACETONITRILA

We report an alternative method for the synthesis of 2-(1,3-dithian-2-ylidene)-acetonitrile using 3-(4-chlorophenyl)-3-oxopropanenitrile and carbon disulfide as starting materials. The methanolysis of the intermediate 3-(4-chlorophenyl)-2-(1,3-dithian-2-ylidene)-3-oxopropanenitrile occurs via three possible intermediates, leading to the formation of the product at a 75% overall yield. Molecular modeling simulation of the reaction pathway using B3LYP 6-311G++(2df,2p) justified the proposed reaction mechanism.

Piezoelectric Ultrasonic Micromotors

This report describes development of micro-fabricated piezoelectric ultrasonic motors and bulk-ceramic piezoelectric ultrasonic motors. Ultrasonic motors offer the advantage of low speed, high torque operation without the need for gears. They can be made compact and lightweight and provide a holding torque in the absence of applied power, due to the traveling wave frictional coupling mechanism between the rotor and the stator. This report covers modeling, simulation, fabrication and testing of ultrasonic motors. Design of experiments methods were also utilized to find optimal motor parameters. A suite of 8 mm diameter x 3 mm tall motors were machined for these studies and maximum stall torques as large as 10^(- 3) Nm, maximum no-load speeds of 1710 rpm and peak power outputs of 27 mW were realized. Aditionally, this report describes the implementation of a microfabricated ultrasonic motor using thin-film lead zirconate titanate. In a joint project with the Pennsylvania State University Materials Research Laboratory and MIT Lincoln Laboratory, 2 mm and 5 mm diameter stator structures were fabricated on 1 micron thick silicon nitride membranes. Small glass lenses placed down on top spun at 100-300 rpm with 4 V excitation at 90 kHz. The large power densities and stall torques of these piezoelectric ultrasonic motors offer tremendous promis for integrated machines: complete intelligent, electro-mechanical autonomous systems mass-produced in a single fabrication process.

Modelación de los sectores estudiados para definir el perfil logístico de Colombia

Colombia siempre ha velado por tener una mejor infraestructura del país, haciendo que se mantenga preocupado por su posición competitiva frente a su desarrollo como hub logístico de Latinoamérica. Esto se ve fundamentado a través de la política nacional logística escrita en el COMPES 3547. Sin embargo, hay un desconocimiento por los empresarios grandes y pequeños del país acerca de las pretensiones que el gobierno quiere llevar a cabo sobre los distintos sectores económicos. La simulación de estructuras como sistemas es de vital importancia para el desarrollo y mejoramiento de cadenas de suministro. La administración de la cadena como sistema que integra procesos permite producir constantemente, mantener niveles adecuados de inventario y cumplir con los requerimientos del cliente final. Lo anterior teniendo en cuenta que los principales actores de la cadena son proveedores, fabricantes, clientes, detallistas, transportadores y distribuidores, En un entorno en el que la globalización constituye quizá el motor más importante para el desempeño de la cadena de suministros, pues rompe barreras geográficas. En síntesis la simulación es un aporte importante para la correcta planeación y operación de la cadena de suministros y esto a la vez permite prestar un buen servicio al cliente mientras se reducen costos y tiempos.

Análise paramétrica da simulação composicional do processo de Drenagem Gravitacional Assistida por Gás (GAGD)

In Brazil and around the world, oil companies are looking for, and expected development of new technologies and processes that can increase the oil recovery factor in mature reservoirs, in a simple and inexpensive way. So, the latest research has developed a new process called Gas Assisted Gravity Drainage (GAGD) which was classified as a gas injection IOR. The process, which is undergoing pilot testing in the field, is being extensively studied through physical scale models and core-floods laboratory, due to high oil recoveries in relation to other gas injection IOR. This process consists of injecting gas at the top of a reservoir through horizontal or vertical injector wells and displacing the oil, taking advantage of natural gravity segregation of fluids, to a horizontal producer well placed at the bottom of the reservoir. To study this process it was modeled a homogeneous reservoir and a model of multi-component fluid with characteristics similar to light oil Brazilian fields through a compositional simulator, to optimize the operational parameters. The model of the process was simulated in GEM (CMG, 2009.10). The operational parameters studied were the gas injection rate, the type of gas injection, the location of the injector and production well. We also studied the presence of water drive in the process. The results showed that the maximum vertical spacing between the two wells, caused the maximum recovery of oil in GAGD. Also, it was found that the largest flow injection, it obtained the largest recovery factors. This parameter controls the speed of the front of the gas injected and determined if the gravitational force dominates or not the process in the recovery of oil. Natural gas had better performance than CO2 and that the presence of aquifer in the reservoir was less influential in the process. In economic analysis found that by injecting natural gas is obtained more economically beneficial than CO2

Estudo da perda de carga e calor no poço injetor no processo De drenagem gravitacional assistida por vapor (SAGD)

The oil companies in the area in general are looking for new technologies that can increase the recovery factor of oil contained in reservoirs. These investments are mainly aimed at reducing the costs of projects which are high. Steam injection is one of these special methods of recovery in which steam is injected into the reservoir in order to reduce the viscosity of the oil and make it more mobile. The process assisted gravity drainage steam (SAGD) using steam injection in its mechanism, as well as two parallel horizontal wells. In this process steam is injected through the horizontal injection well, then a vapor chamber is formed by heating the oil in the reservoir and, by the action of gravitational forces, this oil is drained down to where the production well. This study aims to analyze the influence of pressure drop and heat along the injection well in the SAGD process. Numerical simulations were performed using the thermal simulator STARS of CMG (Computer Modeling Group). The parameters studied were the thermal conductivity of the formation, the flow of steam injection, the inner diameter of the column, the steam quality and temperature. A factorial design was used to verify the influence of the parameters studied in the recovery factor. We also analyzed different injection flow rates for the model with pressure drop and no pressure drop, as well as different maximum flow rates of oil production. Finally, we performed an economic analysis of the two models in order to check the profitability of the projects studied. The results showed that the pressure drop in injection well have a significant influence on the SAGD process.

Análise paramétrica do método de injeção alternada de água e CO2(WAG) em reservatórios de petróleo

After the decline of production from natural energy of the reservoir, the methods of enhanced oil recovery, which methods result from the application of special processes such as chemical injection, miscible gases, thermal and others can be applied. The advanced recovery method with alternating - CO2 injection WAG uses the injection of water and gas, normally miscible that will come in contact with the stock oil. In Brazil with the discovery of pre-salt layer that gas gained prominence. The amount of CO2 present in the oil produced in the pre-salt layer, as well as some reservoirs is one of the challenges to be overcome in relation to sustainable production once this gas needs to be processed in some way. Many targets for CO2 are proposed by researchers to describe some alternatives to the use of CO2 gas produced such as enhanced recovery, storage depleted fields, salt caverns storage and marketing of CO2 even in plants. The largest oil discoveries in Brazil have recently been made by Petrobras in the pre -salt layer located between the states of Santa Catarina and Espírito Santo, where he met large volumes of light oil with a density of approximately 28 ° API, low acidity and low sulfur content. This oil that has a large amount of dissolved CO2 and thus a pioneering solution for the fate of this gas comes with an advanced recovery. The objective of this research is to analyze which parameters had the greatest influence on the enhanced recovery process. The simulations were performed using the "GEM" module of the Computer Modelling Group, with the aim of studying the advanced recovery method in question. For this work, semi - synthetic models were used with reservoir and fluid data that can be extrapolated to practical situations in the Brazilian Northeast. The results showed the influence of the alternating injection of water and gas on the recovery factor and flow rate of oil production process, when compared to primary recovery and continuous water injection or continuous gas injection