Development of a multi-scale finite element model of the osteoporotic lumbar vertebral body for the investigation of apparent level vertebra mechanics and micro-level trabecular mechanics.

Osteoporotic spinal fractures are a major concern in ageing Western societies. This study develops a multi-scale finite element (FE) model of the osteoporotic lumbar vertebral body to study the mechanics of vertebral compression fracture at both the apparent (whole vertebral body) and micro-structural (internal trabecular bone core)levels. Model predictions were verified against experimental data, and found to provide a reasonably good representation of the mechanics of the osteoporotic vertebral body. This novel modelling methodology will allow detailed investigation of how trabecular bone loss in osteoporosis affects vertebral stiffness and strength in the lumbar spine.

Application of micro CT and computation modeling in bone tissue engineering

Computer aided technologies, medical imaging, and rapid prototyping has created new possibilities in biomedical engineering. The systematic variation of scaffold architecture as well as the mineralization inside a scaffold/bone construct can be studied using computer imaging technology and CAD/CAM and micro computed tomography (CT). In this paper, the potential of combining these technologies has been exploited in the study of scaffolds and osteochondral repair. Porosity, surface area per unit volume and the degree of interconnectivity were evaluated through imaging and computer aided manipulation of the scaffold scan data. For the osteochondral model, the spatial distribution and the degree of bone regeneration were evaluated. In this study the versatility of two softwares Mimics (Materialize), CTan and 3D realistic visualization (Skyscan) were assessed, too.

Adapting a generic BEAMnrc model of the BrainLAB m3 micro-multileaf collimator to simulate a local collimation device

This work is focussed on developing a commissioning procedure so that a Monte Carlo model, which uses BEAMnrc’s standard VARMLC component module, can be adapted to match a specific BrainLAB m3 micro-multileaf collimator (μMLC). A set of measurements are recommended, for use as a reference against which the model can be tested and optimised. These include radiochromic film measurements of dose from small and offset fields, as well as measurements of μMLC transmission and interleaf leakage. Simulations and measurements to obtain μMLC scatter factors are shown to be insensitive to relevant model parameters and are therefore not recommended, unless the output of the linear accelerator model is in doubt. Ultimately, this note provides detailed instructions for those intending to optimise a VARMLC model to match the dose delivered by their local BrainLAB m3 μMLC device.

Is providing micro-credit social responsible?

Micro-finance, which includes micro-credit as one it its services, has become big business with a range of models – from those that operate on a strictly business basis to those who come from a philanthropic base, through Non Government organisations (NGOs). Success is often measured by the numbers involved and the repayment rates – which are very high, largely because of the lending models used. The purpose of this paper is to identify whether the means used to deliver micro-credit services to the poor are socially responsible. This paper will explore the range of models currently used and propose a model that addresses some of the social responsibility issues that appear to plague delivery. The model is being developed in Beira, the second largest city in Mozambique. Mozambique exhibits many of the characteristics found in other African countries, so the model, if successful, may have implications for other poor African nations.

Structural analysis of polymeric scaffolds by Micro-CT

The use of porous structures as tissue engineering scaffolds imposes demands on structural parameters such as porosity, pore size and interconnectivity. For the structural analysis of porous scaffolds, micro-computed tomography (μCT) is an ideal tool. μCT is a 3D X-ray imaging method that has several advantages over scanning electron microscopy (SEM) and other conventional characterisation techniques: • visualisation in 3D • quantitative results • non-destructiveness • minimal sample preparation

Micro-CT analysis of tissue engineering scaffold architectures

A novel method was developed for a quantitative assessment of pore interconnectivity using micro-CT data. This method makes use of simulated spherical particles, percolating through the interconnected pore network. For each sphere diameter, the accessible pore volume is calculated. This algorithm was applied to compare pore interconnectivity of two different scaffold architectures; one created by salt-leaching and the other by stereolithography. The algorithm revealed a much higher pore interconnectivity for the latter one.

Micro-family-owned businesses in hostile environment : future engine for growth?

Using panel data from the four waves of the Indonesia Family Life Survey in 1993, 1997, 2000 and 2007 we investigate the prerequisite for and contribution of micro-family-businesses to economic development. We find that family-owned firms are on average fairly profitable compared with the industrial sector profit standard. Failure rates between 1997 and 2000 are very low (about 10%), while the industrial sector experimented a massive shakeout of about 33% in the wake of the 1997 crisis (Ter Wengel & Rodriguez, 2006), with an increase in the number of family-businesses between the two years of observation. This paper contributes to the economics of entrepreneurship studies by continuing the discussion of entrepreneurship in hostile business environments (Baumol, 1990; Sobel, 2008).

Micro-business community responsibility – approaches, motivations and barriers

Micro-businesses, those with fewer than five employees, have a significant impact on the economy. These very small players represent 89% of all Australian businesses and, collectively, they provide 17% of the nation’s private sector employment. They are ubiquitous in Australia as in many other nations, embedded in local communities and therefore well placed to influence community wellbeing. Surprisingly, very little is known about micro-Business Community Responsibility (mBCR), the micro-business equivalent of Small Business Social Responsibility (SBSR) and Corporate Social Responsibility (CSR). Most national data available on business support for community wellbeing does not separately identify micro-business contributions. In this study an exploratory approach informed by business ethics theory was taken. Data from 36 semi-structured interviews was analysed to examine perceived mBCR approaches, motivations and barriers. The sample for this study was a mix of micro-business owner-operators situated in suburban shopping areas in Brisbane. Three types of mBCR emerged. All types are at least partly driven by enlightened selfinterest (ESI). However of the three mBCR types, two combine ESI with other approaches. One type combines ESI and philanthropic approaches to mBCR, and the other combines ESI with social entrepreneurial approaches to mBCR. The combination of doing business and doing good for many micro-business owneroperators, suggests mBCR may be a significant, yet unrecognised component of the third sector social economy.

A socially responsible model of micro-credit delivery to support sustainable community development in emerging economies

Micro-finance, which includes micro-credit as one of its core services, has become an important component of a range of business models – from those that operate on a strictly economic basis to those that come from a philanthropic base, through Non Government Organisations (NGOs). Its success is often measured by the number of loans issued, their size, and the repayment rates. This paper has a dual purpose: to identify whether the models currently used to deliver micro-credit services to the poor are socially responsible and to suggest a new model of delivery that addresses some of the social responsibility issues, while supporting community development. The proposed model is currently being implemented in Beira, the second largest city in Mozambique. Mozambique exhibits many of the characteristics found in other African countries so the model, if successful, may have implications for other poor African nations as well as other developing economies.

Analysis of micro-structural changes and measurement of their parameters of a food material

Food microstructure represents the way their elements arrangement and their interaction. Researchers in this field benefit from identifying new methods of examination of the microstructure and analysing the images. Experiments were undertaken to study micro-structural changes of food material during drying. Micro-structural images were obtained for potato samples of cubical shape at different moisture contents during drying using scanning electron microscopy. Physical parameters such as cell wall perimeter, and area were calculated using an image identification algorithm, based on edge detection and morphological operators. The algorithm was developed using Matlab.