Schottky barrier heights of tantalum oxide, barium strontium titanate, lead zirconate titanate and strontium bismuth tantalate

Schottky barrier heights of various metals on tantalum pentoxide, barium strontium titanate, lead zirconate-titanate and strontium bismuth tantalate have been calculated as a function of metal work function. These oxides have a dimensionless Schottky barrier pinning factor, S, of 0.28 - 0.4 and not close to 1, because S is controlled by the Ti-O type bonds not Sr-O type bonds, as assumed previously. Band offsets on silicon are asymmetric with much smaller offset at the conduction band, so that Ta2O5 and barium strontium titanate (BST) are relatively poor barriers to electrons on Si.

Band alignment between Ta2O5 and metals for resistive random access memory electrodes engineering

Band alignment of resistive random access memory (RRAM) switching material Ta2O5 and different metal electrode materials was examined using high-resolution X-ray photoelectron spectroscopy. Schottky and hole barrier heights at the interface between electrode and Ta2O 5 were obtained, where the electrodes consist of materials with low to high work function (Φ m, v a c from 4.06 to 5.93 eV). Effective metal work functions were extracted to study the Fermi level pinning effect and to discuss the dominant conduction mechanism. An accurate band alignment between electrodes and Ta2O5 is obtained and can be used for RRAM electrode engineering and conduction mechanism study. © 2013 American Institute of Physics.

Promotion of Ceria Catalysts by Precious Metals: Changes in Nature of the Interaction under Reducing and Oxidizing Conditions

By depositing ceria over supported precious metal (PM) catalysts and characterizing them with in situ diffuse reflectance UV (DR UV) and in situ Raman spectroscopy, we have been able to prove a direct correlation between a decrease in ceria band gap and the work function of the metal under reducing conditions. The PM ceria interaction results in changes on the ceria side of the metal ceria interface, such that the degree of oxygen vacancy formation on the ceria surface also correlates with the precious metal work function. Nevertheless, conclusive evidence for a purely electronic interaction could not be provided by X-ray photoelectron spectroscopy (XPS) analysis. On the contrary, the results highlight the complexity of the PM ceria interaction by supporting a spillover mechanism resulting from the electronic interaction under reducing conditions. Under oxidizing conditions, another effect has been observed; namely, a structural modification of ceria induced by the presence of PM cations. In particular, we have been able to demonstrate by in situ Raman spectroscopy that, depending on the PM ionic radius, it is possible to create PM ceria solid solutions. We observed that this structural modification prevails under an oxidizing atmosphere, whereas electronic and chemical interactions take place under reducing conditions.

Tecnologia dels materials

Dins de la disciplina de Ciència i Enginyeria dels Materials, en la qual s’estudia la interrelació entre l’estructura, el processament, les propietats i les aplicacions dels materials, aquest llibre intenta descriure com les tècniques de processament industrial afecten l’estructura dels materials. L’enfocament del text se centra en el material, no pas en les tècniques emprades, temàtica més propera a les tecnologies de fabricació. El temari s’ha organitzat en cinc grans temes. Els quatre primers intenten donar els fonaments d’una tecnologia de processament (colament dels metalls, conformació per deformació, conformació per sinterització, tractaments tèrmics) mentre que el cinquè es dedica a la corrosió. El temari no inclou la tecnologia dels materials polímers que mereixeria un temari específic

Tecnologia dels materials: amb qüestions i exercicis 2a edició [versió html]

Dins de la disciplina de Ciència i Enginyeria dels Materials, en la qual s’estudia la interrelació entre l’estructura, el processament, les propietats i les aplicacions dels materials, aquest llibre intenta descriure com les tècniques de processament industrial afecten l’estructura dels materials. L’enfocament del text se centra en el material, no pas en les tècniques emprades, temàtica més propera a les tecnologies de fabricació. El temari s’ha organitzat en cinc grans temes. Els quatre primers intenten donar els fonaments d’una tecnologia de processament (colament dels metalls, conformació per deformació, conformació per sinterització, tractaments tèrmics) mentre que el cinquè es dedica a la corrosió. El temari no inclou la tecnologia dels materials polímers que mereixeria un temari específic

Exposure to fumes and gases during welding operations

The exposure to fumes and gases is one of the hazards associated with welding operations. Apart from research conducted on the mechanism of fume and gas formation and the relationship between fume formation rates and common welding parameters, little is known about the exposure process during welding. This research project aimed to identify the factors that influence exposure, develop an understanding of their role in the exposure process and through this understanding formulate strategies for the effective control of exposure during welding. To address these aims a literature review and an experimental program was conducted The literature review surveyed epidemiological, toxicological and exposure data. The experimental program involved three approaches, the first, an evaluation of the factors that influence exposure by assessing a metal inert gas/mild steel welding process in a workshop setting. The second approach involved the study of exposure in a controlled environment provided by a wind tunnel and simulated welding process. The final approach was to investigate workplace conditions through an assessment of exposure and control strategies in industry. The exposure to fumes and gases during welding is highly variable and frequently in excess of the health based exposure standards. Exposure is influenced by a number of a factors including the welding process, base material, arc time, electrode, arc current, arc voltage, arc length, electrode polarity, shield gas, wire-to-metal-work distance (metal inert gas), metal transfer mode, intensity of the UV radiation (ozone), the frequency of arc ignitions (ozone), thermal buoyancy generated by the arc process, ventilation (natural and mechanical), the welding environment, the position of the welder, the welders stance, helmet type, and helmet position. Exposure occurs as a result of three processes: the formation of contaminants at or around the arc region; their transport from the arc region, as influenced by the entry and thermal expansion of shield gases, the vigorous production of contaminants, thermal air currents produced by the heat of the arc process, and ventilation; and finally the entry of contaminants into the breathing zone of the welder, as influenced by the position of the welder, the welders stance, helmet type, and the helmet position. The control of exposure during welding can be achieved by several means: through the selection of welding parameters that generate low contaminant formation rates; through the limitation of arc time; and by isolating the breathing zone of the welder from the contaminant plume through the use of ventilation, welder position or the welding helmet as a physical barrier. Effective control is achieved by careful examination of the workplace, the selection of the most appropriate control option, and motivation of the workforce.

Mechanisms of dynamic strain induced transformation and post-deformation evolution

In this study, a novel experimental approach was applied to study the mechanism of the equiaxed shape retention in dynamic strain induced ferrite during deformation. The post-deformation ferrite evolution in both static and dynamic transformation was studied. The refinement potential and the origin of their differences in both mechanisms were analysed.

Tailoring a lubricant for use with ZINCANNEAL steel

To be sent to dfm week beg. 9/9/02.

Sheared edge quality in the trimming of sheet metals

Examines the sheared edge quality of different automotive sheet metals resulting from the trimming process using experimental tooling and finite element modelling. The significant differences in burr, sliver and edge profile formation have been explained in terms of the strain distribution and tensile properties of the materials.

Compression and extrusion of metals using rotating dies

Experimental and theoretical investigations of compression and extrusion of metals with steadily or cyclically rotating dies were carried out. Reasonably simple models were produced by classical plasticity theory and analytical equations were developed to establish a theoretical basis for the associated phenomena. Analytical solutions agreed well with the experimental results.

Influence of processing on the roll forming characteristics of recovery annealed steel

Roll forming (including corrugating) of high strength steel has for many years been treated as an art rather than a science. This work, by using analysis at both the microscopic and standard mechanical level, has demystified the production of these high strength steels, and has helped point the direction for further development of these efficient construction products.

Ultrafine ferrite formation in steels through thermomechanical processing

The main aim of this study was to investigate the critical conditions for the formation of ultrafine grain structures using hot torsion and wedge rolling techniques. In addition, the effect of thermomechanical parameters and steel composition on the critical conditions for ultrafine grain structure formation has been systematically evaluated.

Low strain processing of LC and ULC steels

Temper rolling and tension levelling are commonly used to manufacture flat rolled steel. Both processes lengthen the steel at strains up to 3% by applying a load and stretching the strip. By latering the balance between the load and the tension the formability of the low carbon and ultra low carbon steel may be optimised.

Softening during the hot deformation of steel

The behaviour of steel undergoing hot deformation was examined with the aim of better understanding the softening mechanisms operating during industrial hot strip rolling. These softening mechanisms can significantly influence the deformation force required to attain a given reduction in thickness, and this work answered a number of questions with regard to the transition between softening mechanisms.

Experimental analysis of friction in forming automotive coated steels

The thesis addressed and answered a number of key issues in the experimental analysis of friction in sheet forming operations. Conventional friction theories were linked with the properties of sheet coatings and the process geometries. Newly derived mathematical models extended the analysis of friction in sheet metal forming applications.