Análise superficial em AFM de filmes finos com gradiente de composição em profundidade obtidos por codeposição catódica

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Física

Experimental study of the mechanical properties and durability of self-compacting mortars with nano materials (SiO2 and TiO2)

Resumo: Cement, as well as the remaining constituents of self-compacting mortars, must be carefully selected, in order to obtain an adequate composition with a granular mix as compact as possible and a good performance in the fresh state (self-compacting effect) and the hardened state (mechanical and durability-related behavior). Therefore in this work the possibility of incorporating nano particles in self-compacting mortars was studied. Nano materials are very reactive due mostly to their high specific surface and show a great potential to improve the properties of these mortars, both in mechanical and durability terms. In this work two nano materials were used, nano silica (nano SiO2) in colloidal state and nano titanium (nano TiO2) in amorphous state, in two types of self-compacting mortars (ratio binder:sand of 1:1 and 1:2). The self-compacting mortar mixes have the same water/cement ratio and 30% of replacement of cement with fly ashes. The influence of nano materials nano-SiO2 and nano-TiO2 on the fresh and hardened state properties of these self-compacting mortars was studied. The results show that the use of nano materials in repair and rehabilitation mortars has significant potential but still needs to be optimized. (C) 2015 Elsevier Ltd. All rights reserved.

Desenvolvimento de células solares de Si nano-estruturado para aplicação em azulejos solares

Dissertação apresentada para a obtenção do Grau de Mestre em Engenharia de Materiais, pela Universidade Nova de Lisboa,Faculdade de Ciências e Tecnologia

Desenvolvimento de um sensor para detecção de nano e micro concentrações de deltametrina

Dissertação para obtenção do Grau de Mestre em Engenharia Física

Desenvolvimento e caracterização de filmes de nano-compósitos de TiO2/WO3 pela técnoca de pulverização catódica

Dissertação para obtenção do Grau de Mestre em Engenharia Física

Biodispositivos electrónicos implantáveis e biodegradáveis: estudo de nano/microfibras de polivinilpirrolidona-PVP

Dissertação para obtenção do Grau de Mestre em Engenharia Biomédica

Biodispositivos electrónicos implantáveis e biodegradáveis: nano/microfibras de poli (ε-caprolactona) (PCL)

Dissertação para obtenção do Grau de Mestre em Engenharia Biomédica

Imunobiossensores capacitivos interdigitais com camadas sensíveis micro e nano-estruturadas

Dissertação para obtenção do Grau de Mestre em Biotecnologia

Molecular characterization of the fibrinogen-erythrocyte interaction and its influence on cardiovascular pathologies by AFM-based force spectroscopy

Dissertação para obtenção do Grau de Mestre em Engenharia Biomédica

Produção e caracterização de biobaterias a partir de matrizes de nano-microfibras

Na vanguarda do desenvolvimento tecnológico impõe-se o desenvolvimento de sistemas inovadores capazes de gerar energia eléctrica e de responder às necessidades relativas de miniaturização da nova geração de biodispositivos electrónicos portáteis, sem fios e auto-suficientes. O objectivo deste trabalho consistiu na produção e caracterização de um dispositivo electroquímico (biobateria) de espessura reduzida e flexível, capaz de gerar energia eléctrica a partir de fluidos biológicos, como o sangue ou suor. Parte da investigação incidiu sobre a produção e caracterização da matriz de nano-microfibras de policaprolactona. Esta matriz constitui a base dos dispositivos produzidos. Foi obtida através da técnica de electrofiação, consistindo numa membrana porosa, flexível e com elevada área superficial. Posteriormente, em ambas as faces da membrana foram depositados eléctrodos metálicos pela técnica de evaporação térmica assistida por canhão de electrões. Os estudos realizados, que incluíram a análise do comportamento electroquímico através de voltametria cíclica e espectroscopia de impedância, revelaram que os dispositivos produzidos apresentam um desempenho que depende do tempo de imersão em fluidos biológicos (como o suor), da espessura da membrana assim como dos materiais empregues na formação dos eléctrodos. Por último, procedeu-se à demonstração da aplicabilidade do dispositivo produzido colocando-o sobre pele suada e obtiveram-se valores de tensão e corrente promissores que podem levar à aplicação deste dispositivo em pacemakers, dispositivos biomédicos auto-alimentados, entre outros.

Cellulose micro/nano fibers conformational effects probed by nematic liquid crystal droplets

Probing micro-/nano-sized surface conformations, which are ubiquitous in biological systems, by using liquid crystal droplets, which change their ordering and optical appearance in response to the presence of more than ten times smaller cellulose based micro/nano fibers, might find new uses in a range of biological environments and sensors. Previous studies indicate that electrospun micro/nano cellulosic fibers produced from liquid crystalline solutions could present a twisted form [1]. In this work, we study the structures of nematic liquid crystal droplets threaded by cellulose fibers prepared from liquid crystalline and isotropic solutions as well as droplets pierced by spider-made fibers [2]. Planar anchoring at the fibers and planar and homeotropic at the drop surfaces allowed probing cellulose fibers different helical structures as well as aligned filaments.

Writing/erasing 3D micro and nano wrinkles in flexible elastomers for volatile organic compounds sensor

Micro/nano wrinkled patterns on cross-linked urethane/urea polymeric flexible free standing films with two soft segments, polypropylene oxide and polybutadiene, can be induced by UV-irradiation. The ability to write/erase these 3D structures, in a controlled manner, is the main focus of this work. The imprinting of the wrinkled structures was accomplished by swelling in an appropriate solvent followed by drying the membranes after the cross-linking process and UV irradiation. The surface tailoring of the elastomeric membranes was imaged by optical microscopy, scanning electronic microscopy and by atomic force microscopy. To erase the wrinkled structures the elastomers were swollen. The swelling as well as the sol/gel fraction and the UV radiation were tuned in order to control the wrinkles characteristics. It was found that the wrinkles wavelength, in the order of microns (1±0,25μm), was stamped by the UV radiation intensity and exposure time while the wrinkles' amplitude, in the order of nanometers (150-450 nm), was highly dependent on the swelling and sol/gel fraction. A prototype for volatile organic compounds detection was developed taking advantage of the unique 3D micro/nano wrinkles features.

Risk assessment in a research laboratory during sol–gel synthesis of nano-TiO2

The occupational risks in the nanotechnology research laboratories are an important topic since a great number of researchers are involved in this area. The risk assessment performed by both qualitative and quantitative methods is a necessary step for the management of the occupational risks. Risk assessment could be performed by qualitative methods that gather consensus in the scientific community. It is also possible to use quantitative methods, based in different technics and metrics, as indicative exposure limits are been settled by several institutions. While performing the risk assessment, the information on the materials used is very important and, if it is not updated, it could create a bias in the assessment results. The exposure to TiO2 nanoparticles risk was assessed in a research laboratory using a quantitative exposure method and qualitative risk assessment methods. It was found the results from direct-reading Condensation Particle Counter (CPC) equipment and the CB Nanotool seem to be related and aligned, while the results obtained from the use of the Stoffenmanager Nano seem to indicate a higher risk level.

Investigation on the homogeneity and stability of aqueous nano cellulose suspensions prepared using pluronic F-127

This paper presents the results of experimental investigation on the aqueous dispersion behaviour of micro crystalline cellulose (MCC) prepared using Pluronic F-127. For this purpose, different concentrations (0.5-3.0 wt.%) of MCC were dispersed in water with the help of ultrasonication technique using various concentrations of Pluronic F-127. The homogeneity of the suspensions and agglomerations were characterized by optical and transmission electron microscopy and the concentration of well dispersed MCC was measured using UV-Vis spectroscopy. Also, the suspensions were subjected to high speed ultracentrifugation at 3000 rpm and observed visually for sedimentation and subsequently, concentration was calculated using UV-Vis, in order to assess the long term stability of the suspensions. Based on these experiments, optimum concentration of Pluronic to disperse different MCC concentrations has been suggested.

An experimental investigation on nano-TiO2 and fly ash based high performance concrete

High performance concrete (HPC) offers several advantages over normal-strength concrete, namely, high mechanical strength and high durability. Therefore, HPC allows for concrete structures with less steel reinforcement and a longer service life, both of which are crucial issues in the eco-efficiency of construction materials. Nevertheless international publications on the field of concrete containing nanoparticles are scarce when compared to Portland cement concrete (around 1%) of the total international publications. HPC nanoparticle-based publications are even scarcer. This article presents the results of an experimental investigation on the mechanical properties and durability of HPC based on nano-TiO2 and fly ash. The durability performance was assessed by means of water absorption by immersion, water absorption by capillarity, ultrasonic pulse velocity, electric resistivity, chloride diffusion and resistance to sulphuric acid attack. The results show that the concretes containing an increased content of nano-TiO2 show decreased durability performance. The results also show that concrete with 1% nano-TiO2 and 30% fly ash as Portland cement replacement show a high mechanical strength (C55/C67) and a high durability. However, it should be noted that the cost of nano-TiO2 is responsible for a severe increase in the cost of concrete mixtures.