CMOS indoor light energy harvesting system for wireless sensing applications

Dissertação para obtenção do Grau de Doutor em Engenharia Electrotécnica e de Computadores

Design of a low-voltage CMOS RF receiver for energy harvesting sensor node

In this thesis a CMOS low-power and low-voltage RF receiver front-end is presented. The main objective is to design this RF receiver so that it can be powered by a piezoelectric energy harvesting power source, included in a Wireless Sensor Node application. For this type of applications the major requirements are: the low-power and low-voltage operation, the reduced area and cost and the simplicity of the architecture. The system key blocks are the LNA and the mixer, which are studied and optimized with greater detail, achieving a good linearity, a wideband operation and a reduced introduction of noise. A wideband balun LNA with noise and distortion cancelling is designed to work at a 0.6 V supply voltage, in conjunction with a double-balanced passive mixer and subsequent TIA block. The passive mixer operates in current mode, allowing a minimal introduction of voltage noise and a good linearity. The receiver analog front-end has a total voltage conversion gain of 31.5 dB, a 0.1 - 4.3 GHz bandwidth, an IIP3 value of -1.35 dBm, and a noise figure lower than 9 dB. The total power consumption is 1.9 mW and the die area is 305x134.5 m2, using a standard 130 nm CMOS technology.

Light harvesting in solar cells using natural pigments from red fruits adsorbed to mesoporous TiO2

Nature has developed strategies to present us with a wide variety of colours, from the green of leaves to the bright colours seen in flowers. Anthocyanins are between these natural pigments that are responsible for the great diversity of colours seen in flowers and fruits. Anthocyanins have been used to sensitize titanium dioxide (TiO2) in Dye-Sensitized Solar Cells (DSSCs). DSSCs have become one of the most popular research topic in photovoltaic cells due to their low production costs when compared to other alternatives. DSSCs are inspired in what happens in nature during photosynthesis. A primary charge separation is achieved by means of a photoexcited dye capable of performing the electron injection into the conduction band of a wide band-gap semiconductor, usually TiO2. With this work we aimed to synthesize a novel mesoporous TiO2 structure as the semiconductor in order to increase the dye loading. We used natural occurring dyes such as anthocyanins and their synthetic flavylium relatives, as an alternative to the widely used metal complexes of Ru(II) which are expensive and are environmentally unsafe. This offers not only the chance to use safer dyes for DSSCs, but also to take profit of waste biological products, such as wine and olive oil production residues that are heavily loaded with anthocyanin dyes. We also performed a photodegradation study using TiO2 as the catalyst to degrade dye contaminants, such as those from the wine production waste, by photo-irradiation of the system in the visible region of the light spectrum. We were able to succeed in the synthesis of mesoporous TiO2 both powder and thin film, with a high capacity to load a large amount of dye. We proved the concept of photodegradation using TiO2 as catalyst. And finally, we show that wine production waste is a possible dye source to DSSCs application.

Harvest control rule vs optimal harvesting of an age-structured population: The case of the Ibero-Atlantic Sardine Fishery

Research Masters

Energy harvesting device based on a metallic glass/PVDF magnetoelectric laminated composite

A flexible and low cost energy harvester device based on the magnetoelectric (ME) effect has been designed using Fe64Co17Si7B12 as amorphous magnetostrictive ribbons and PVDF as the piezoelectric element. Sandwich-type laminated composite of 3 cm long has been fabricated by gluing these ribbons to the PVDF with the Devcon 5 minute epoxy. Good power output and power density of 6.4 μW and 1.5 mW/cm3, respectively, have been obtained through a multiplier circuit. All values have been measured at the magnetomechanical resonance of the laminate. The effect of the length of the ME laminate on the power output has been also studied, exhibiting a decay as the length of the ME laminate does. Nevertheless, good performance of such device has been obtained for a 0.5 cm long device, working already at 337 KHz, within the low radio frequency (LRF) range.

Energy harvesting performance of BaTiO3/poly(vinylidene fluoride-trifluoroethylene) spin coated nanocomposites

The energy harvesting efficiency of poly(vinylidene fluoride-trifluoroethylene) spin coated films and its nanocomposites with piezoelectric BaTiO3 have been investigated as a function of ceramic filler size and content. It is found that the best energy harvesting performance of ~0.28 W is obtained for the nanocomposite samples with 20% filler content of 10 nm size particles and for 5% filler content for the 100 and 500 nm size fillers. For the larger filler average sizes, the power decreases for filler contents above 5% due to increase of the mechanical stiffness of the samples. Due to the similar dielectric characteristics of the samples, the performance is mainly governed by the mechanical response. The obtained power values, easy processing and the low cost and robustness of the polymer, allow the implementation of the material for micro and nanogenerator applications.

Optimization of magnetoelectric composites based on electroactive polymers for energy harvesting and sensor application

Tese de Doutoramento em Engenharia de Materiais.

A spin-offs journey into achieving marketable products from bacterial cellulose

[Excerpt] Academic spin-offs, technological ventures born inside Universities, have increasingly strengthen the connections between the scholarship and the economy, by fostering the role of technology transfer and knowledge commercialization. This presentation will outline the major steps in taking an idea or a technology to market, growing the venture and aiming at securing a successful exit. Also, it will present BCTechnologies (Bacterial Cellulose Technologies), a spin-off from the University of Minho (Portugal). (...)

The relation of the concentration of macronutrients in the substrate and in the foliage to cell wall thickness and cellulose concentration in the xylem of slash pine (Pinus elliotti)

Sand culture experiments, using a sub-irrigation technique, were installed in order to find out the effects of the macronutrients N, P, K, Ca, Mg and S on growth, aspect, mineral composition, length of fibers, thickness of cell wall and cellulose concentration in slash pine. The aim was to obtain, under controlled conditions, basic information which could eventually lead to practical means designed to increase the rate of growth and to make of slash pine a richer source of cellulose. Nitrogen, Phosphorus, Potassium Experiment A 3 x 3 x 3 factorial design with two replicates was used. Nitrogen was supplied initially at the levels of 25, 50 and 100 ppm; phosphorus was given at the rates of 5, 10 and 20 ppm; potassium was supplied at the rates of 25, 50 and 100 ppm; six months after the experiment was started the first level for each element was dropped to zero. Others macro and all micronutrients were supplied at uniform rates. Fifteen hours of illumination per day were provided. The experimental technique for growing the slash pine seedlings proved quite satisfactory. Symptoms of deficiency of nitrogen, phosphorus and potassium were observed, described and recorded in photographs and water colors. These informations will help to identify abnormalities which may appear under field conditions. Chemical analysis of the several plant parts, on the other hand, give a valuable means to assess the nutritional status of slash pine, thus confirming when needed, the visual diagnosis. The correctness of manurial pratices, on the other hand, can be judged with the help of the analytical data tabulated. Under the experimental conditions nitrogen caused the highest increases on growth, as measured by increments in height and dry weights, whereas the effects of phosphorus and potassium were less marked. Cellulose concentration was not significantly affected by the treatments used. Higher levels of N seemed to decrease both length of fiber elements and the thickness of cell wall. The effects of P and K were not well defined. Calcium, Magnesium, Sulfur Experiment A 3 x 3 x 3 factorial design with two replicates was used. Calcium was supplied initially at the levels of 12.5, 25 and 50 ppm; magnesium and sulfur were given at the rates of 6, 12.5 and 25 ppm. Other macro and micronutrients were supplied at uniform rates, common to all treatments. Three months after starting the experiment the first level for each element was dropped to zero. Symptoms of deficiency of calcium, magnesium and sulfur were observed, described and recorded as in the case of the previous experiment. Chemical analysis were made, both for mineral content and cellulose concentration. Length of fibers and thickness of cell wall were measured. Both calcium and magnesium increase height, sulfur failing to give significant response. Dry weight was beneficially affected by calcium and sulfur. The levels of calcium, magnesium and sulfur in the needles associated with deficiency and maximum growth are comparable with those found in the literature. Cellulose concentration increased when the level of sulfur in the substrate was raised. The thickness of cell wall was negatively affected by the treatments; no effect was observed with regards to length of fibers.

Design, modeling and control of an autonomous field robot for white asparagus harvesting

Magdeburg, Univ., Fak. für Maschinenbau, Diss., 2014

Advantages of a modified gastroscope for video-assisted internal mammary artery harvesting.

Instead of standard rigid thoracoscopes, we used a modified gastroscope for video assistance during 12 minimally invasive left internal mammary harvesting. Flexibility and remote control of its last centimeters give to the gastroscope a total freedom of movements, and perfect positioning in every direction. The scope is equipped with cold light, a suction canal and an irrigation canal, which allow for in situ washing without needing to remove it from the thoracic cavity. Thanks to these advantages, vision and lighting are always perfect.

III Simpósio Brasileiro de Captação de Água de Chuva no Semi-Árido - os Sistemas de Water Harvesting e sua Aplicação em Cabo Verde

A localização geográfica do arquipélago de Cabo Verde na zona saheliana entre as isoietas de 250 mm e 500 mm aproximadamente, aliada aos condicionalismos físicos, climáticos e económicos explicam em grande parte, os escassos recursos hídricos disponíveis. Devido ao caracter torrencial das chuvas, os resultados de aplicação das diferentes técnicas e sistemas de “water harvesting”, provaram no passado de que se tratam de tecnologias que podem contribuir para uma melhor gestão dos recursos hídricos. Por esta razão, deverão continuar a fazer parte dos programas de investigação aplicada, aperfeiçoadas e divulgadas no seio das comunidades rurais e nas áreas urbanas devido ao baixo custo do preço da água captada e as vantagens de caracter ambiental. Este trabalho faz uma abordagem sobre as tecnologias de aproveitamento de águas superficiais, com destaque para os sistemas de “water harvesting”, e discute as potencialidades do seu desenvolvimento em Cabo Verde.

Insects associated with tropical foliage produced in the coffee growing region of Colombia

We conducted a survey of insects and pest management practices on 34 farms growing ornamental tropical foliage plants in the central coffee region of Colombia over two years. Tropical foliage provided habitat for a diverse range of insects. In total, phytophagous or detritivorous insects from six orders, 40 families and 62 genera were collected. The most common were Hemiptera (29 genera from 16 families), followed by Coleoptera (17 genera from 4 families), Diptera (5 genera from 5 families), Lepidoptera (5 genera from 4 families), Hymenoptera (3 genera from 2 families) and Orthoptera (2 genera from 2 families). The most common phytophagous species were leaf cutting ants (Atta and Acromyrmex spp.), leaf beetles (Chrysomelidae), leafhoppers (Cicadellidae), stinkbugs (Pentatomidae), squash bugs (Coreidae), tree hoppers (Membracidae) and plant hoppers (Fulgoridae). Beneficial insects identified from tropical foliage included predators and parasitoids amongst 5 orders, 12 families and 22 genera. The most abundant were predators among the Coccinellidae, Chrysopidae, Reduviidae, Lycidae and Formicidae but only low numbers of parasitoids (Ichneumonidae, Braconidae and Tachinidae) were collected. A pest management questionnaire given to growers revealed a preponderance of reliance on broad spectrum insecticides with a smaller number of growers (approximately one third) also using some biological control methods. Our survey contributes basic information regarding diversity of Neotropical insects associated with ornamental foliage plants.

Iliac wing fracture following graft harvesting from the anterior iliac crest: literature review based on a case report.

The morbidity of bone graft harvesting from the iliac crest has been widely discussed in the literature. For some authors, it is considered to be low and for others relatively high. We report on a case of a fracture of the iliac wing after graft harvesting from the anterior iliac crest despite good surgical technique. This complication is well known and most of these fractures heal uneventfully if treated conservatively. However, if anatomical and technical considerations are respected, the patient could be spared this inconvenience. Based on a literature review, we discuss the procedure's potential complications and how to avoid them in an update.