Effect of citrate ions on the electrochemical behaviour of low-carbon steel in borate buffer solutions

The electrochemical behaviour of cold-rolled low carbon steel was studied on both active and passive potential regions in borate buffer solutions with and without the addition of sodium citrate (NaCit). In the active region anodic charges increased significantly and RCT values decreased with citrate, due to the formation of soluble complexes. In the passive potential region the film formed at +0.4 V in borate buffer solution with and without 0.010 M NaCit is probably enriched by Fe3O4 oxide, while films formed at +0.8 V are probably enriched by gamma-Fe2O3. The equivalent circuit [R-s(R(CT)Q)] fitted all experimental impedance data. (C) 2003 Elsevier Ltd. All rights reserved.

Optimization of the mechanical properties of low-carbon steels by formation of a multiphase microstructure

In this work five methods of heat treatments are investigated in order to obtained convenient volume fractions of ferrite, bainite, martensite and retained austenite, starting with a low carbon steel and seeking the distinction of the phases, through optical microscopy. Specific chemical etching is improved. The results in tensile and fatigue tests were accomplished and the results were related with the microstructural parameters. The results show that the mechanical properties are closely related with the phases, grains size and the phases morphology. Copyright © 2001 Society of Automotive Engineers, Inc.

Microstructure evolution during warm deformation of low carbon steel with dispersed cementite

The microstructure evolution and mechanical behavior during large strain of a 0.16%C-Mn steel has been investigated by warm torsion tests. These experiments were carried out at 685°C at equivalent strain rate of 0.1 s . The initial microstructure composed of a martensite matrix with uniformly dispersed fine cementite particles was attained by quenching and tempering. The microstructure evolution during tempering and straining was performed through interrupted tests. As the material was reheated to testing temperature, well-defined cell structure was created and subgrains within lath martensite were observed by TEM; strong recovery took place, decreasing the dislocation density. After 1 hour at the test temperature and without straining, EBSD technique showed the formation of new grains. The flow stress curves measured had a peculiar shape: rapid work hardening to a hump, followed by an extensive flow-softening region. 65% of the boundaries observed in the sample strained to ε = 1.0 were high angle grain boundaries. After straining to ε = 5.0, average ferrite grain size close to 1.5 μm was found, suggesting that dynamic recrystallization took place. Also, two sets of cementite particles were observed: large particles aligned with straining direction and smaller particles more uniformly dispersed. The fragmentation or grain subdivision that occurred during reheating and tempering time was essential for the formation of ultrafine grained microstructure.

Low-carbon transport infrastructure: Experiences in Latin America

This issue of the Bulletin compiles and analyses the principal measures adopted by a group of countries in Latin America to reduce carbon emissions in the transport sector. These measures are the first steps towards a low-carbon transport infrastructure.

Transport, the poor and moving towards low-carbon societies

This FAL Bulletin discusses the challenges involved in creating equality in urban mobility and the need to reach towards a social sustainability framework, as existing policies often accentuate current inequities and inequalities in accessibility. Lack of access to mobility has wide-ranging effects across social groups, gender and particularly the urban poor.

Towards low-carbon transportation infrastructures

This bulletin discusses the importance of low-carbon transportation infrastructures for the integrated development of the region.

Energie rinnovabili e tecnologie "low carbon" per la produzione di biocombustibili sostenibili in paesi in via di sviluppo: il caso della Jatropha Curcas. Progetto per l'autonomia energetica di una scuola e di un ambulatorio medico in Tanzania e Madagascar.

Le tematiche che saranno affrontate all’interno del mio elaborato toccano diversi temi sensibili, tutti relativi all’ambiente e alla sua conservazione. Nella prima parte della tesi parlerò di riscaldamento globale, cambiamento climatico ma soprattutto di energie rinnovabili, in particolare l’energia da biomasse. Nella parte centrale la lente di ingrandimento verrà posta sui diversi tipi di energia e sulle relative tecnologie. Mi concentrerò prevalentemente sugli oli vegetali a scopo energetico descrivendo le principali colture e le tecnologie di estrazione. Proseguirò quindi con un excursus sulla Jatropha Curcas descrivendo in dettaglio le caratteristiche di tale coltura in termini di arboricoltura e utilizzi energetici. L’ultima parte dell’elaborato sarà dedicata all’esposizione di due casi applicativi riguardanti la Jatropha Curcas, in particolare il dimensionamento energetico di una scuola e di un ambulatorio medico in Tanzania e Madagascar.

Laboratory and field investigation of the performance of suction drains, a novel low-carbon technology for ground stabilization

Con riferimento alla realizzazione di tunnel per servizi interrati, l’incertezza che contraddistingue il quadro geologico, oltre che incidere sui costi, riveste un ruolo chiave nella progettazione preliminare. Sebbene un’approfondita caratterizzazione geotecnica e geologica del volume di terreno inerente l’opera di scavo sia generalmente parte integrante del progetto, non è comunque possibile eliminare del tutto tali incertezze per via dell’estensione del volume interessato oltre che per la disomogeneità che sempre contraddistingue il terreno. Generalmente, investigazioni in corso d’opera e interventi di stabilizzazione devono essere previsti per contenere i costi di perforazione ed ottimizzare la progettazione. Ad esempio, tra i metodi di esplorazione geotecnica figurano i tunnel pilota, i quali sono in grado di garantire un’ottimale caratterizzazione del quadro geotecnico del sottosuolo. Con riferimento agli interventi di stabilizzazione del terreno, adottabili laddove una perforazione tradizionale non consentirebbe il tunnelling, vi è un vasta gamma di scelta. Pertanto, da una prima analisi delle problematiche connesse al tunnelling emerge che la stabilizzazione delle facce di scavo riveste un’importanza e un risconto applicativo di prim’ordine. Questa tesi si inserisce all’interno di un progetto che promuove un’innovativa ed economica tecnica di stabilizzazione dei tunnel per suzione tenendo quindi conto dell’influenza della suzione sulla coesione non drenata.

An Investigation of Silicon Impregnation of Low-Carbon Steels

A problem of metallurgy during the last part of the Nineteenth and the early Twentieth Century, and one that stood very near the front, was investigations of methods to produce a non-corrosive surface on iron and steel without affecting the physical properties of these base metals.

Hot-Dip Aluminizing of Low-Carbon Steels

In a relatively short period of sixty-five years, aluminum has grown to the rank of fifth in total weight of met­als produced in the world. Throughout its short life, aluminum has been found to have excellent corrosion-resistant properties; yet only in recent years has aluminum been under consideration as a corrosion-resistant coating for iron and steel.

Blends of babassu, palm kernal and coconut mame with fossil kerosene: low carbon number methyl esters as a possible source for renewable jet fuel

Three different oils: babassu, coconut and palm kernel have been transesterified with methanol. The fatty acid methyl esters (FAME) have been subjected to vacuum fractional distillation, and the low boiling point fractions have been blended with fossil kerosene at three different proportions: 5, 10 and 20% vol.

Pathways to Low Carbon Transport in the EU – From Possibility to Reality. Report of the CEPS Task Force on transport and climate change. CEPS Task Force Report, June 2013

A new CEPS Task Force Report has identified possible pathways for achieving the EU’s ambitious climate change targets. It concludes that a GHG emissions reduction in line with EU climate change policy is possible, but it requires immediate action. This report argues that most of the reductions required of the transport sector in the EU could come from more energy-efficient vehicles, combined with the gradual introduction of low-carbon fuels and new engine technologies. The key policy for reducing GHG emissions in road transport is the steady tightening of emissions standards in line with technological progress. The report also identifies strategies for the transport system to become more energy and/or carbon efficient, arguing that leverage can be further enhanced by local and city governments’ incentives for efficient and low-carbon vehicles in line with local circumstances and choices. The Task Force on Low Carbon Transport brought together a diverse set of stakeholders from the car and oil industries, business associations, international organisations, member states, academic experts and NGOs. This authoritative report is the result of that unique collaboration.

Reforming the Market Design of EU Electricity Markets: Addressing the Challenges of a Low-Carbon Power Sector. CEPS Task Force Report, 27 July 2015

This CEPS Task Force Report focuses on whether there is a need to adapt the EU’s electricity market design and if so, the options for doing so. In a first step, it analyses the current market trends by distinguishing between their causes and their consequences. Then, the current blueprint of EU power market design – the target model – is briefly introduced, followed by a discussion of the shortcomings of the current approach and the challenges in finding suitable solutions. The final chapter offers an inventory of solutions differentiating between recommendations shared among Task Force members and non-consensual options.