Accurately simulating the production of radiotherapy portal images using non-zero beam angles

In this study, the delivery and portal imaging of one square-field and one conformal radiotherapy treatment was simulated using the Monte Carlo codes BEAMnrc and DOSXYZnrc. The treatment fields were delivered to a humanoid phantom from different angles by a 6 MV photon beam linear accelerator, with an amorphous-silicon electronic portal imaging device (a-Si EPID) used to provide images of the phantom generated by each field. The virtual phantom preparation code CTCombine was used to combine a computed-tomography-derived model of the irradiated phantom with a simple, rectilinear model of the a-Si EPID, at each beam angle used in the treatment. Comparison of the resulting experimental and simulated a-Si EPID images showed good agreement, within \[gamma](3%, 3 mm), indicating that this method may be useful in providing accurate Monte Carlo predictions of clinical a-Si EPID images, for use in the verification of complex radiotherapy treatments.

Determinants of skin self-examination (SSE) in men aged 50 years or older

Background: Queensland men aged 50 years and older are at high risk for melanoma. Early detection via skin self examination (SSE) (particularly whole-body SSE) followed by presentation to a doctor with suspicious lesions, may decrease morbidity and mortality from melanoma. Prevalence of whole-body SSE (wbSSE) is lower in Queensland older men compared to other population subgroups. With the exception of the present study no previous research has investigated the determinants of wbSSE in older men, or interventions to increase the behaviour in this population. Furthermore, although past SSE intervention studies for other populations have cited health behaviour models in the development of interventions, no study has tested these models in full. The Skin Awareness Study: A recent randomised trial, called the Skin Awareness Study, tested the impact of a video-delivered intervention compared to written materials alone on wbSSE in men aged 50 years or older (n=930). Men were recruited from the general population and interviewed over the telephone at baseline and 13 months. The proportion of men who reported wbSSE rose from 10% to 31% in the control group, and from 11% to 36% in the intervention group. Current research: The current research was a secondary analysis of data collected for the Skin Awareness Study. The objectives were as follows: • To describe how men who did not take up any SSE during the study period differed from those who did take up examining their skin. • To determine whether the intervention program was successful in affecting the constructs of the Health Belief Model it was aimed at (self-efficacy, perceived threat, and outcome expectations); and whether this in turn influenced wbSSE. • To determine whether the Health Action Process Approach (HAPA) was a better predictor of wbSSE behaviour compared to the Health Belief Model (HBM). Methods: For objective 1, men who did not report any past SSE at baseline (n=308) were categorised as having ‘taken up SSE’ (reported SSE at study end) or ‘resisted SSE’ (reported no SSE at study end). Bivariate logistic regression, followed by multivariable regression, investigated the association between participant characteristics measured at baseline and resisting SSE. For objective 2 proxy measures of self-efficacy, perceived threat, and outcome expectations were selected. To determine whether these mediated the effect of the intervention on the outcome, a mediator analysis was performed with all participants who completed interviews at both time points (n=830) following the Baron and Kenny approach, modified for use with structural equation modelling (SEM). For objective 3, control group participants only were included (n=410). Proxy measures of all HBM and HAPA constructs were selected and SEM was used to build up models and test the significance of each hypothesised pathway. A likelihood ratio test compared the HAPA to the HBM. Results: Amongst men who did not report any SSE at baseline, 27% did not take up any SSE by the end of the study. In multivariable analyses, resisting SSE was associated with having more freckly skin (p=0.027); being unsure about the statement ‘if I saw something suspicious on my skin, I’d go to the doctor straight away’ (p=0.028); not intending to perform SSE (p=0.015), having lower SSE self-efficacy (p<0.001), and having no recommendation for SSE from a doctor (p=0.002). In the mediator analysis none of the tested variables mediated the relationship between the intervention and wbSSE. In regards to health behaviour models, the HBM did not predict wbSSE well overall. Only the construct of self-efficacy was a significant predictor of future wbSSE (p=0.001), while neither perceived threat (p=0.584) nor outcome expectations (p=0.220) were. By contrast, when the HAPA constructs were added, all three HBM variables predicted intention to perform SSE, which in turn predicted future behaviour (p=0.015). The HAPA construct of volitional self-efficacy was also associated with wbSSE (p=0.046). The HAPA was a significantly better model compared to the HBM (p<0.001). Limitations: Items selected to measure HBM and HAPA model constructs for objectives 2 and 3 may not have accurately reflected each construct. Conclusions: This research added to the evidence base on how best to target interventions to older men; and on the appropriateness of particular health behaviour models to guide interventions. Findings indicate that to overcome resistance those men with more negative pre-existing attitudes to SSE (not intending to do it, lower initial self-efficacy) may need to be targeted with more intensive interventions in the future. Involving general practitioners in recommending SSE to their patients in this population, alongside disseminating an intervention, may increase its success. Comparison of the HBM and HAPA showed that while two of the three HBM variables examined did not directly predict future wbSSE, all three were associated with intention to self-examine skin. This suggests that in this population, intervening on these variables may increase intention to examine skin, but not necessarily the behaviour itself. Future interventions could potentially focus on increasing both the motivational variables of perceived threat and outcome expectations as well as a combination of both action and volitional self-efficacy; with the aim of increasing intention as well as its translation to taking up and maintaining regular wbSSE.

The Kinaesthetic Fusion Effect : fast-forward 30 years

This study investigated the Kinaesthetic Fusion Effect (KFE) first described by Craske and Kenny in 1981. The current study did not replicate these findings following a change in the reporting method used by participants. Participants did not perceive any reduction in the sagittal separation of a button pressed by the index finger of one arm and a probe touching the other, following repeated exposure to the tactile stimuli present on both unseen arms. This study’s failure to replicate the widely-cited KFE as described by Craske et al. (1984) suggests that it may be contingent on several aspects of visual information, especially the availability of a specific visual reference, the role of instructions regarding gaze direction, and the potential use of a line of sight strategy when referring felt positions to an interposed surface. In addition, a foreshortening effect was found; this may result from a line-of-sight judgment and represent a feature of the reporting method used. Finally, this research will benefit future studies that require participants to report the perceived locations of the unseen limbs.

Femoral impaction grafting in revision total hip arthroplasty

Between 1987 and 1999, 540 revision total hip replacements in 487 patients were performed at our institution with the femoral impaction grafting technique with a cemented femoral stem. All patients were prospectively followed for 2-15years post-operatively with no loss to follow-up. 494 hips remained successfully in situ at an average 6.7years. The ten year survival rate was 98.0% (95% CI 96.2 to 99.8) with aseptic loosening as the endpoint and 84.2% (95% CI 78.5 to 89.9) for re-operation for any reason. Indication for surgery and the use of any kind of reinforcement significantly influenced outcome (p<0.001). This is the largest known series of revision THR with femoral impaction grafting and the results support continued use of this technique.

Acetabular impaction grafting in total hip replacement

Background and purpose: Acetabular impaction grafting has been shown to have excellent results, but concerns regarding its suitability for larger defects have been highlighted. We report the use of this technique in a large cohort of patients with the aim of better understanding the limitations of the technique. Methods: We investigated a consecutive group of 339 cases of impaction grafting of the cup with morcellised impacted allograft bone for survivorship and mechanisms for early failure. Results: Kaplan Meier survival was 89.1% (95% CI 83.2 to 95.0%) at 5.8 years for revision for any reason, and 91.6% (95% CI 85.9 to 97.3%) for revision for aseptic loosening of the cup. Of the 15 cases revised for aseptic cup loosening, nine were large rim mesh reconstructions, two were fractured Kerboull-Postel plates, two were migrating cages, one medial wall mesh failure and one impaction alone failed. Interpretation: In our series, results were disappointing where a large rim mesh or significant reconstruction was required. In light of these results, our technique has changed in that we now use predominantly larger chips of purely cancellous bone, 8-10 mm3 in size, to fill the cavity and larger diameter cups to better fill the mouth of the reconstructed acetabulum. In addition we now make greater use of i) implants made of a highly porous in-growth surface to constrain allograft chips and ii) bulk allografts combined with cages and morcellised chips in cases with very large segmental and cavitary defects.

Elaborating a tactile-proprioceptive illusion : the kinaesthetic fusion effect

This study investigated the Kinaesthetic Fusion Effect (KFE) first described by Craske and Kenny in 1981. In Experiment 1 the study did not replicate these findings following a change in the reporting method used by participants. Participants did not perceive any reduction in the sagittal separation of a button pressed by the index finger of one arm and a probe touching the other, following repeated exposure to the tactile stimuli present on both unseen arms. This study’s failure to replicate the widely-cited KFE as described by Craske et al. (1984) suggests that it may be contingent on several aspects of visual information, especially the availability of a specific visual reference, the role of instructions regarding gaze direction, and the potential use of a line of sight strategy when referring felt positions to an interposed surface. In addition, a foreshortening effect was found; this may result from a line-of-sight judgment and represent a feature of the reporting method used. Finally, this research will benefit future studies that require participants to report the perceived locations of the unseen limbs. Experiment 2 investigated the KFE when the visual reference was removed and participants made reports of touched position, blindfolded. A number of interesting outcomes arose from this change and may provide clarification to the phenomena.

Monte Carlo verification of gel dosimetry measurements for stereotactic radiotherapy

The quality assurance of stereotactic radiotherapy and radiosurgery treatments requires the use of small-field dose measurements that can be experimentally challenging. This study used Monte Carlo simulations to establish that PAGAT dosimetry gel can be used to provide accurate, high resolution, three-dimensional dose measurements of stereotactic radiotherapy fields. A small cylindrical container (4 cm height, 4.2 cm diameter) was filled with PAGAT gel, placed in the parietal region inside a CIRS head phantom, and irradiated with a 12 field stereotactic radiotherapy plan. The resulting three-dimensional dose measurement was read out using an optical CT scanner and compared with the treatment planning prediction of the dose delivered to the gel during the treatment. A BEAMnrc DOSXYZnrc simulation of this treatment was completed, to provide a standard against which the accuracy of the gel measurement could be gauged. The three dimensional dose distributions obtained from Monte Carlo and from the gel measurement were found to be in better agreement with each other than with the dose distribution provided by the treatment planning system's pencil beam calculation. Both sets of data showed close agreement with the treatment planning system's dose distribution through the centre of the irradiated volume and substantial disagreement with the treatment planning system at the penumbrae. The Monte Carlo calculations and gel measurements both indicated that the treated volume was up to 3 mm narrower, with steeper penumbrae and more variable out-of-field dose, than predicted by the treatment planning system. The Monte Carlo simulations allowed the accuracy of the PAGAT gel dosimeter to be verified in this case, allowing PAGAT gel to be utilised in the measurement of dose from stereotactic and other radiotherapy treatments, with greater confidence in the future.

A microanalytical study of the surfaces of normal, delipidized, and artificially “resurfaced” articular cartilage

The surface amorphous layer of articular cartilage is of primary importance to its load-bearing and lubrication function. This lipid-filled layer is degraded/disrupted or eliminated when cartilage degenerates due to diseases. This article examines further the characteristic of this surface overlay using a combination of microscopy and imaging methods to evaluate the hypothesis that the surface of articular cartilage can be repaired by exposing degraded cartilage to aqueous synthetic lipid mixtures. The preliminary results demonstrate that it is possible to create a new surface layer of phospholipids on the surface of cartilage following artificial lipid removal, but such a layer does not possess enough mechanical strength for physiological function when created with either unsaturated palmitoyloleoyl- phosphatidylcholine or saturated dipalmitoyl-phosphatidylcholine component of joint lipid composition alone. We conclude that this may be due to low structural cohesivity, inadequate time of exposure, and the mix/content of lipid in the incubation environment.

Interplay effects during enhanced dynamic wedge deliveries

In this study the interplay effects for Enhanced Dynamic Wedge (EDW) treatments are experimentally investigated. Single and multiple field EDW plans for different wedge angles were delivered to a phantom and detector on a moving platform, with various periods, amplitudes for parallel and perpendicular motions. A four field 4D CT planned lung EDW treatment was delivered to a dummy tumor over four fractions. For the single field parallel case the amplitude and the period of motion both affect the interplay resulting in the appearance of a step function and penumbral cut off with the discrepancy worst where collimator-tumor speed is similar. For perpendicular motion the amplitude of tumor motion is the only dominant factor. For large wedge angle the dose discrepancy is more pronounced compared to the small wedge angle for the same field size and amplitude-period values. For a small field size i.e. 5 × 5 cm2 the loss of wedged distribution was observed for both 60º and 15º wedge angles for of parallel and perpendicular motions. Film results from 4D CT planned delivery displayed a mix of over and under dosages over 4 fractions, with the gamma pass rate of 40% for the averaged film image at 3%/1 mm DTA (Distance to Agreement). Amplitude and period of the tumor motion both affect the interplay for single and multi-field EDW treatments and for a limited (4 or 5) fraction delivery there is a possibility of non-averaging of the EDW interplay.

The effect of very small air gaps on small field dosimetry

The purpose of this study was to investigate the effect of very small air gaps (less than 1 mm) on the dosimetry of small photon fields used for stereotactic treatments. Measurements were performed with optically stimulated luminescent dosimeters (OSLDs) for 6 MV photons on a Varian 21iX linear accelerator with a Brainlab μMLC attachment for square field sizes down to 6 mm × 6 mm. Monte Carlo simulations were performed using EGSnrc C++ user code cavity. It was found that the Monte Carlo model used in this study accurately simulated the OSLD measurements on the linear accelerator. For the 6 mm field size, the 0.5 mm air gap upstream to the active area of the OSLD caused a 5.3 % dose reduction relative to a Monte Carlo simulation with no air gap. A hypothetical 0.2 mm air gap caused a dose reduction > 2 %, emphasizing the fact that even the tiniest air gaps can cause a large reduction in measured dose. The negligible effect on an 18 mm field size illustrated that the electronic disequilibrium caused by such small air gaps only affects the dosimetry of the very small fields. When performing small field dosimetry, care must be taken to avoid any air gaps, as can be often present when inserting detectors into solid phantoms. It is recommended that very small field dosimetry is performed in liquid water. When using small photon fields, sub-millimetre air gaps can also affect patient dosimetry if they cannot be spatially resolved on a CT scan. However the effect on the patient is debatable as the dose reduction caused by a 1 mm air gap, starting out at 19% in the first 0.1 mm behind the air gap, decreases to < 5 % after just 2 mm, and electronic equilibrium is fully re-established after just 5 mm.

Sustainable infrastructure operations : a review of assessment schemes and decision support

Infrastructure forms a vital component in supporting today’s way of life and has a significant role or impact on economic, environmental and social outcomes of the region around it. The design, construction and operation of such assets are a multi-billion dollar industry in Australia alone. Another issue that will play a major role in our way life is that of climate change and the greater concept of sustainability. With limited resources and a changing natural world it is necessary for infrastructure to be developed and maintained in a manner that is sustainable. In order to achieve infrastructure sustainability in operations it is necessary for there to be: a sustainability assessment scheme that provides a scientifically sound and realistic approach to measuring an assets level of sustainability; and, systems and tools to support the making of decisions that result in sustainable outcomes by providing feedback in a timely manner. Having these in place will then help drive the consideration of sustainability during the decision making process for infrastructure operations and maintenance. In this paper we provide two main contributions; a comparison and review of sustainability assessment schemes for infrastructure and their suitability for use in the operations phase; and, a review of decision support systems/tools in the area of infrastructure sustainability in operations. For this paper, sustainability covers not just the environment, but also finance/economic and societal/community aspects as well. This is often referred to as the Triple Bottom Line and forms one of the three dimensions of corporate sustainability [Stapledon, 2004].

Oriented graphitic carbon films for hydrogen gas sensors

An oriented graphitic nanostructured carbon film has been employed as a conductometric hydrogen gas sensor. The carbon film was energetically deposited using a filtered cathodic vacuum arc with a -75 V bias applied to a stainless steel grid placed 1cm from the surface of the Si substrate. The substrate was heated to 400°C prior to deposition. Electron microscopy showed evidence that the film consisted largely of vertically oriented graphitic sheets and had a density of 2.06 g/cm3. 76% of the atoms were bonded in sp2 or graphitic configurations. A change in the device resistance of >; 1.5% was exhibited upon exposure to 1 % hydrogen gas (in synthetic, zero humidity air) at 100°C. The time for the sensor resistance to increase by 1.5 % under these conditions was approximately 60 s and the baseline (zero hydrogen exposure) resistance remained constant to within 0.01% during and after the hydrogen exposures.

Normanton2020

Normanton2020 This exhibition showcases the work of 3rd -4th year undergraduate landscape architecture, architecture, Interior Design, Environmental Engineering, Civil Engineering students in response to issues of sustainability in the Gulf of Carpentaria town of Normanton. 16 students and four staff set off on a 2488km journey to undertake the second half of the Carpentaria Project (following Linking Karumba: Creating Sustainable Connections 2008), in the other Carpentaria Shire town of Normanton. This project, Get EnGulfed: Normanton 2020, looked back and forwards to propose strategies strengthening local and regional identities. Our project partners recognised the need for a strategic approach to developing future visions for Normanton’s growth as a socially, culturally, economically and ecologically sustainable town in the decade to 2020. They proposed: Project aims to foster: • Enhanced liveability; • A strengthened expression of town identity; • Expanded sustainable tourism. Primary challenges & opportunities: • Remoteness; • Two seasons: wet & dry; • Local economy; • Society and Cultural Heritage. The Exhibition Four groups of four students produced four strategic planning and design options toward this future: Mud Maps of Normanton: Rhys Belnap, AJ Humphries, Amos Shirreff, Haiku Van Keuk Normanton: Stay Another Day: Belle Dalton, Tom Jordan, Josh Nielsen, Carla Ramsland The Sweet Spot on the Savannah Way: Daniel Lapham, Yvonne Phillips, Patrick Poon, Dan Young Resilience Through Diversity: Jillian Kenny, Tania Metcher, Stephen Orr, Evan Thompson

Get EnGulfed: Normanton2020

Get EnGulfed: Normanton2020 This exhibition showcases the work of 3rd -4th year undergraduate landscape architecture, architecture, Interior Design, Environmental Engineering, Civil Engineering students in response to issues of sustainability in the Gulf of Carpentaria town of Normanton. It presented the work to QUT staff from across the university, as well as industry partners and invited guests. 16 students and four staff set off on a 2488km journey to undertake the second half of the Carpentaria Project (following Linking Karumba: Creating Sustainable Connections 2008), in the other Carpentaria Shire town of Normanton. This project, Get EnGulfed: Normanton 2020, looked back and forwards to propose strategies strengthening local and regional identities. Our project partners recognised the need for a strategic approach to developing future visions for Normanton’s growth as a socially, culturally, economically and ecologically sustainable town in the decade to 2020. They proposed: Project aims to foster: • Enhanced liveability; • A strengthened expression of town identity; • Expanded sustainable tourism. • Primary challenges & opportunities: • Remoteness; • Two seasons: wet & dry; • Local economy; • Society and Cultural Heritage. The Exhibition Four groups of four students produced four strategic planning and design options toward this future: Mud Maps of Normanton: Rhys Belnap, AJ Humphries, Amos Shirreff, Haiku Van Keuk Normanton: Stay Another Day: Belle Dalton, Tom Jordan, Josh Nielsen, Carla Ramsland The Sweet Spot on the Savannah Way: Daniel Lapham, Yvonne Phillips, Patrick Poon, Dan Young Resilience Through Diversity: Jillian Kenny, Tania Metcher, Stephen Orr, Evan Thompson

Dosimetric effects of a high-density spinal implant

In this study, a treatment plan for a spinal lesion, with all beams transmitted though a titanium vertebral reconstruction implant, was used to investigate the potential effect of a high-density implant on a three-dimensional dose distribution for a radiotherapy treatment. The BEAMnrc/DOSXYZnrc and MCDTK Monte Carlo codes were used to simulate the treatment using both a simplified, recltilinear model and a detailed model incorporating the full complexity of the patient anatomy and treatment plan. The resulting Monte Carlo dose distributions showed that the commercial treatment planning system failed to accurately predict both the depletion of dose downstream of the implant and the increase in scattered dose adjacent to the implant. Overall, the dosimetric effect of the implant was underestimated by the commercial treatment planning system and overestimated by the simplified Monte Carlo model. The value of performing detailed Monte Carlo calculations, using the full patient and treatment geometry, was demonstrated.