Construção e avaliação de célula de fluxo para estudo da tensão interfacial dinâmica da interface fluxo líquido - sólido por despolarização da fluorescência

A simple low-cost flow cell was developed, built and optimized in order to observe dynamic interfacial tension of continuous flow systems. Distinct materials can be used in one of the cell walls in order to observe the intermolecular forces between the flowing liquid and the chemical constitution of the walls. The fluorescence depolarization was evaluated using Rhodamine B as fluorescent probe seeded in ethylene glycol. The effects of the positioning angles on the data acquired across the cell are reported. The reproducibility of the data was evaluated with a spectrometer assembled in-house and the relative standard deviation was below 3%.

Optimization of strength and toughness on the effect of the weldable high strength steels (hss) used in offshore structures

Optimization of high strength and toughness combination on the effect of weldability is very vital to be considered in offshore oil and gas industries. Having a balanced and improved high strength and toughness is very much recommended in offshore structures for an effective production and viable exploration of hydrocarbons. This thesis aims to investigate the possibilities to improve the toughness of high strength steel. High carbon contents induce hardness and needs to be reduced for increasing toughness. The rare combination of high strength with high toughness possibilities was examined by determining the following toughening mechanism of: Heat treatment and optimal microstructure, Thermomechanical processing, Effect of welding parameters on toughness and weldability of steel. The implementation of weldability of steels to attain high toughness for high strength in offshore structures is mostly in shipbuilding, offshore platforms, and pipelines for high operating pressures. As a result, the toughening mechanisms suggested have benefits to the aims of the effect of high strength to high toughness of steel for efficiency, production and cost reduction.

Interfacial effects in organic solar cells

Solceller baserade på organiska halvledare erbjuder en möjlighet till storskalig och billig solenergiproduktion. Organiska halvledare har den fördelen att de är lösningsprocesserbara vilket gör att solceller och andra elektroniska komponenter baserade på dessa halvledare kan tillverkas vid låga temperaturer och med liten energiförbrukning. Nackdelen med dessa material är deras strukturella och energetiska oordning som leder till lägre effektivitet. För att organiska solceller ska kunna kommersialiseras krävs grundläggande insikter i de olika processer som begränsar effektiviteten. En stor del av forskningen om dessa processer har varit fokuserad kring egenskaperna av solcellens olika komponenter (de aktiva materialen) som sådana, medan gränsytorna mellan olika material har fått mindre uppmärksamhet. Gränsytor mellan olika material har distinkt olika egenskaper jämfört med ett rent material, och gränsytors olika egenskaper kan ha en väldigt stor inverkan på hur solcellerna fungerar. Syftet med denna avhandling är att klargöra några olika gränsyterelaterade effekter i organiska dioder och solceller. De gränsytor som behandlas är gränsytan mellan kontakten och det aktiva lagret (metall-organisk) och gränsytan mellan donor och acceptor (organisk-organisk). Resultaten visar att metall-organiska gränsytor måste designas noggrant för att begränsa förlust av effektivitet. En icke-idealisk kontakt leder till starkt reducerad effektivitet på grund av att elektronerna extraheras ineffektivt. Även till synes idealiska kontakter kan orsaka förluster genom spontan laddningsöverföring från metallen till det organiska lagret som effektivt sett minskar på den spänning som cellen kan alstra. Den organisk-organiska gränsytan påverkar hur mycket ström cellen kan alstra och beroende på gränsytans beskaffenhet kan de negativa rekombinationsprocesserna i materialet kontrolleras. ------------------------------------------------- Orgaanisille puolijohteille perustuvat aurinkokennot mahdollistavat suurimuotoisen ja edullisen aurinkoenergiatuotannon. Orgaanisten puolijohteiden etu on että ne voidaan liuottaa, jolloin aurinkokennot ja muut näille johteille perustuvat elektroniset komponentit voidaan valmistaa alhaisessa lämpötilassa kuluttaen vähän energiaa. Materiaalien huonona puolena on kuitenkin niiden rakenteellinen ja energeettinen epäjärjestys, jonka seurauksena niiden tehokkuus on huonompi. Orgaanisten aurinkokennojen kaupallistaminen edellyttää perustavanlaatuista ymmärystä tehokkuutta rajoittavista prosesseista. Aurinkokennotutkimus on pääosin keskittynyt aurinkokennon eri komponenttien (aktiivisten materiaalien) ominaisuuksiin, kun taas eri materiaalien rajapinnat ovat jääneet vähemmälle huomiolle. Eri materiaalien välisillä rajapinnoilla on huomattavan erilaisia ominaisuuksia verrattuna puhtaisiin materiaaleihin. Rajapintojen ominaisuudet voivat kuitenkin vaikuttaa merkittävästi aurinkokennojen toimintaan. Tämän väitöstutkimuksen tarkoituksena on selventää joitain rajapintoihin liittyviä toimintoja orgaanisissa diodeissa ja aurinkokennoissa. Käsiteltävät rajapinnat ovat rajapinta kontaktin ja aktiivisen kerroksen välillä (metallis-orgaaninen) ja rajapinta donorin ja akseptorin välillä (orgaanis-orgaaninen). Tutkimustulokset osoittavat, että metallis-orgaaniset rajapinnat tulee suunnitella huolellisesti, jotta tehokkuuden alenemista voidaan rajoittaa. Mikäli kontakti ei ole ideaalisti suunniteltu, vähenee tehokkuus huomattavasti, mikä johtuu elektronien tehottomasta ekstrahoinnista. Jopa ideaalisilta vaikuttavat kontaktit voivat johtaa tehokkuuden alenemiseen, mikäli varaus siirtyy spontaanisti metallista orgaaniseen kerrokseen, sillä tämä alentaa jännitettä jonka kenno voi tuottaa. Kennon orgaanis-orgaaninen rajapinta vaikuttaa siihen, kuinka paljon virtaa kenno pystyy tuottamaan. Rajapinnan ominaisuuksista riippuen materiaalin rekombinaatio on hallittavissa.

Cure Characteristics of Short Polyester Fiber-PolyurethaneElastomer Composite with Interfacial Bonding Agents Based on Polymeric 4,4'-Diphenylmethanediisocyanate

Cure characteristics of short polyester fiber-polyurethane composites with respect to different bonding agents (MD resins) based on 4, 4' diphenylmethanediisocyanate (MDI) and various diols like propyleneglycol (PG), polypropyleneglycol (PPG) and glycerol (GL) were studied. Tmax. - Tmin. of composites having MD resin were found to be higher than the composite without MD resin. Minimum torque and Tmax. - Tmin., scorch time and optimum cure time were increased with the increase of MDI equivalence. Optimum ratio of MDI / -of in the resin was found to be within the range of 1-1.5. It was observed from the cure characteristics that for getting better adhesion between short polyester fiber and the polyurethane matrix the best choice of MD resin was one based on MDI and 1:1 equivalent mixture of polypropyleneglycol and glycerol.

Rheological Properties of Short Polyester Fiber-Polyurethane Elastomer Composite with Different Interfacial Bonding Agents

The rheological behavior of a short-polyester-fiber-filled polyurethane elastomer composite containing different bonding agents has been studied in the temperature range 120-160°C and in the shear rate range 63-608 s-'. The composite with and without bonding agents showed a pseudoplastic behavior which decreased with the increase of temperature. Composites containing bonding agents based on polypropyleneglycol and 4,4'-diphenylmethanediisocyanate showed the lowest viscosity values at a particular shear rate, whereas composites containing a glycerol- (GL) based bonding agent showed the highest viscosity. The viscosity of the composite decreased sharply after a particular temperature (140°C) and the fall was less drastic in the composite containing a GL-based bonding agent.

Stress Relaxation of Polyester Fiber-Polyurethane Elastomer Composite with Different Interfacial Bonding Agents

The stress relaxation behavior of polyurethane elastomer and short polyester fiber filled elastomer composites with and without bonding agents at different strain levels and strain rates was studied. It was found that these compounds exhibit a multistage relaxation mechanism and that the rate of relaxation and cross-over time depend on the strain level and strain rate. The incorporation of fibers reduced the stage-I relaxation rate and increased the cross-over time of the gum vulcanisate. A higher rate of relaxation (first stage) was shown by the composites with longitudinal fiber orientation and composites with bonding agents.

Studies on the curing of short polyester fiber-polyurethane elastomer composite with different interfacial bonding agents

The cure characteristics of short fiber-polyurethane elastomer were studied with respect to different fiber-matrix bonding agents. A hexamethylenetetramine- resorcinol -hydrated silica based bonding agent was found to affect the stability of the composite. A new bonding agent, TP resin, based on polymeric toluenediisocyanate and polypropylene glycol has been developed. Cure characteristics of the composite with and without TP resin at different fiber loadings were also compared. Minimum torque, scorch time and optimum cure time increased with fiber content. Maximum torque was consistently higher with TP resin at all fiber loadings.

Thermal Conduction in Polymeric Nanofluids and Nanosolids Controlled by Interfacial Scattering:Solutions to Some Selected Problems

Dept.of Instrumentation,Cochin University of Science and Technology

“Studies on short polyester fiber - polyurethane elastomer composite with different interfacial bonding agents”

The work presented in this thesis is regarding the development and evaluation of new bonding agents for short polyester fiber - polyurethane elastomer composites. The conventional bonding system based on hexamethylenetetramine, resorcinol and hydrated silica was not effective as a bonding agent for the composite, as the water eliminated during the formation of the RF resin hydrolysed the urethane linkages. Four bonding agents based on MDI/'I‘DI and polypropyleneglycol, propyleneglycol and glycerol were prepared and the composite recipe was optimised with respect to the cure characteristics and mechanical properties. The flow properties, stress relaxation pattern and the thermal degradation characteristics of the composites containing different bonding agents were then studied in detail to evaluate the new bonding systems. The optimum loading of resin was 5 phr and the ratio of the -01 to isocyanate was 1:1. The cure characteristics showed that the optimum combination of cure rate and processability was given by the composite with the resin based on polypropyleneglycol/ glycerol/ 4,4’diphenylmethanediisocynate (PPG/GL/MDI). From the rheological studies of the composites with and without bonding agents it was observed that all the composites showed pseudoplastic nature and the activation energy of flow of the composite was not altered by the presence of bonding agents. Mechanical properties such as tensile strength, modulus, tear resistance and abrasion resistance were improved in the presence of bonding agents and the effect was more pronounced in the case of abrasion resistance. The composites based on MDI/GL showed better initial properties while composites with resins based on MDI/PPG showed better aging resistance. Stress relaxation showed a multistage relaxation behaviour for the composite. Within the-strain levels studied, the initial rate of relaxation was higher and the cross over time was lesser for the composite containing bonding agents. The bonding agent based on MDI/PPG/GL was found to be a better choice for improving stress relaxation characteristics with better interfacial bonding. Thennogravimetirc analysis showed that the presence of fiber and bonding agents improved the thennal stability of the polyurethane elastomer marginally and it was maximum in the case of MDI / GL based bonding agents. The kinetics of degradation was not altered by the presence of bonding agents

Microwave exfoliated reduced graphene oxide epoxy nanocomposites for high performance applications

Graphene has captured the attention of scientific community due to recently emerging high performance applications. Hence, studying its reinforcing effects on epoxy resin is a significant step. In this study, microwave exfoliated reduced graphene oxide (MERGO) was prepared from natural graphite for subsequent fabrication of epoxy nanocomposites using triethylenetetramine (TETA) as a curing agent via insitu polymerization. Thermogravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), C13 NMR spectroscopy, X-ray photoelectron spectroscopy (XPS) and ultravioletevisible (UVevis) spectroscopy were employed to confirm the simultaneous reduction and exfoliation of graphene oxide. The reinforcing effect of MERGO on epoxy resin was explored by investigating its static mechanical properties and dynamic mechanical analysis (DMA) at MERGO loadings of 0 to 0.5 phr. The micro-structure of epoxy/MERGO nanocomposites was investigated using scanning electron microscope (SEM), transmission electron microscope (TEM) and XRD techniques. The present work reports an enhancement of 32%, 103% and 85% in tensile, impact and flexural strength respectively of epoxy by the addition of even 0.25 phr MERGO. At this loading elastic and flexural moduli also increased by 10% and 65%, respectively. Single-edge-notch three-point-Bending (SEN-TPB) fracture toughness (KIC) measurements were carried out where a 63% increase was observed by the introduction of 0.25 phr MERGO. The interfacial interactions brought about by graphene also benefited the dynamic mechanical properties to a large extent in the form of a significant enhancement in storage modulus and slightly improved glass transition temperature. Considerable improvements were also detected in dielectric properties. The epoxy nanocomposite also attained an ac conductivity of 10 5 S/m and a remarkable increase in dielectric constant. The simple and cost effective way of graphene synthesis for the fabrication of epoxy/MERGO nanocomposites may be extended to the preparation of other MERGO based polymer nanocomposites. This remarkable class of materials has thrown open enormous opportunities for developing conductive adhesives and in microelectronics

Oxidation of silicon: further tests for the interfacial silicon emission model

The classical description of Si oxidation given by Deal and Grove has well-known limitations for thin oxides (below 200 Ã). Among the large number of alternative models published so far, the interfacial emission model has shown the greatest ability to fit the experimental oxidation curves. It relies on the assumption that during oxidation Si interstitials are emitted to the oxide to release strain and that the accumulation of these interstitials near the interface reduces the reaction rate there. The resulting set of differential equations makes it possible to model diverse oxidation experiments. In this paper, we have compared its predictions with two sets of experiments: (1) the pressure dependence for subatmospheric oxygen pressure and (2) the enhancement of the oxidation rate after annealing in inert atmosphere. The result is not satisfactory and raises serious doubts about the model’s correctness

Interfacial structure of wild-type and mutant forms of puroindoline-b bound to DPPG monolayers

The interaction of wild-type puroindoline-b (Pin-b+) and two mutant forms having single residue substitutions (G46S or W44R) with L-alpha-dipalmitoylphosphatidyl-dl-glycerol (DPPG) as a Langmuir monolayer at the air/water interface was investigated by neutron reflectivity (NR) and Brewster angle microscopy (BAM). NR profiles were fitted using a three-layer model to enable differences in penetration of protein between the lipid headgroup and acyl regions to be determined. The data showed similar surface excesses for each of the three proteins at the interface; however, it was revealed that the depth of penetration of protein into the lipid region differed for each protein with Pin-b+ penetrating further into the acyl region of the lipid compared to the mutant forms of the protein that interacted with the headgroup region only. BAM images revealed that the domain structure of the DPPG monolayers was disrupted when Pin-b+ adsorption had reached equilibrium, suggesting protein penetration had led to compression of the lipid region. In contrast, the domain structure was unaffected by the W44R mutant, suggesting no change in compression of the lipid region and hence little or no penetration of protein into the lipid layer.

Fracture toughness and cutting

An exploratory model for cutting is presented which incorporates fracture toughness as well as the commonly considered effects of plasticity and friction. The periodic load fluctuations Been in cutting force dynamometer tests are predicted, and considerations of chatter and surface finish follow. A non-dimensional group is put forward to classify different regimes of material response to machining. It leads to tentative explanations for the difficulties of cutting materials such as ceramics and brittlo polymers, and also relates to the formation of discontinuous chips. Experiments on a range of solids with widely varying toughness/strength ratios generally agree with the analysis.